Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CIRCULAR CONFIGURATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Structural Sizing of a 25,000-lb Payload, Air-Breathing Launch Vehicle For Single-Stage-To-Orbit

In support of NASA's Air-Breathing Launch Vehicle (ABLV) study, a 25,000-lb payload version of the GTX (formerly Trailblazer) reference vehicle concept was developed. The GTX is a vertical lift-off, reusable, single-stage-to-orbit launch vehicle concept that uses hypersonic air-breathing propulsion in a rocket-based combined-cycle (RBCC) propulsion system to reduce the required propellant fraction. To achieve this goal the vehicle and propulsion system must be well integrated both aerodynamically and structurally to reduce weight. This study demonstrates the volumetric and structural efficiency of a vertical takeoff, horizontal landing, hypersonic vehicle with a circular cross section. A departure from the lifting body concepts, this design philosophy is even extended to the engines, which have semicircular nacelles symmetrically mounted on the vehicle. Material candidates with a potential for lightweight and simplicity have been selected from a set of near term technologies (5 to 10 years). To achieve the mission trajectory, preliminary weight estimates show the vehicle's gross lift-off weight is 1.26 x 10(exp 6) lb. The structural configuration of the GTX vehicle and its propulsion system are described. The vehicle design benefits are presented, and key technical issues are highlighted.

Roche, Joseph M.↗

Pitched and Yawed Circular Jets in Cross-Flow

Results from an experimental investigation of flow field generated by pitched and yawed jets discharging from a flat plate into a cross-flow are presented. The circular jet was pitched at alpha = 20 degrees and 45 degrees and yawed between beta = 0 degrees and 90 degrees in increments of 15 degrees. The measurements were performed with two X-wires providing all three components of velocity and turbulence intensity. These data were obtained at downstream locations of x = 3, 5, 10 and 20, where the distance x normalized by the jet diameter, is measured from the center of the orifice. Data for all configurations were acquired at a momentum-flux ratio J = 8. Additionally, for selected angles and locations, surveys were conducted for J = 1.5, 4, and 20. As expected, the jet penetration is found to be higher at larger alpha. With increasing beta the jet spreads more. The rate of reduction of peak streamwise vorticity, with the downstream distance is significantly lessened at higher alpha but is found to be practically independent of alpha. Thus, at the farthest measurement station x = 20, omega(sub xmax) is about five times larger for beta = 0 degrees compared to the levels at beta = 0 degrees. Streamwise velocity within the jet-vortex structure is found to depend on the parameter J. At J = 1.5 and 4, 'wake-like' velocity profiles are observed. In comparison, a 'jet-like' overshoot is present at higher J.

Milanovic, Ivana M.↗

Noise Reduction Through Circulation Control

Circulation control technology uses tangential blowing around a rounded trailing edge or a leading edge to change the force and moment characteristics of an aerodynamic body. This technology has been applied to circular cylinders, wings, helicopter rotors, and even to automobiles for improved aerodynamic performance. Only limited research has been conducted on the acoustics of this technology. Since wing flaps contribute to the environmental noise of an aircraft, an alternate blown high lift system without complex mechanical flaps could prove beneficial in reducing the noise of an approaching aircraft. Thus, in this study, a direct comparison of the acoustic characteristics of high lift systems employing a circulation control wing configuration and a conventional wing flapped configuration has been made. These results indicate that acoustically, a circulation control wing high lift system could be considerably more acceptable than a wing with conventional mechanical flaps.

Munro, Scott E.↗

Noise Reduction Through Circulation Control

Circulation control technology uses tangential blowing around a rounded trailing edge or a leading edge to change the force and moment characteristics of an aerodynamic body. This technology has been applied to circular cylinders, wings, helicopter rotors, and even to automobiles for improved aerodynamic performance. Only limited research has been conducted on the acoustic of this technology. Since wing flaps contribute to the environmental noise of an aircraft, an alternate blown high lift system without complex mechanical flaps could prove beneficial in reducing the noise of an approaching aircraft. Thus, in this study, a direct comparison of the acoustic characteristics of high lift systems employing a circulation control wing configuration and a conventional wing flapped configuration has been made. These results indicate that acoustically, a circulation control wing high lift system could be considerably more acceptable than a wing with conventional mechanical flaps.

Munro, Scott E.↗

CFD Simulations of the IHF Arc-Jet Flow: Compression-Pad/Separation Bolt Wedge Tests

This paper reports computational analyses in support of two wedge tests in a high enthalpy arc-jet facility at NASA Ames Research Center. These tests were conducted using two different wedge models, each placed in a free jet downstream of a corresponding different conical nozzle in the Ames 60-MW Interaction Heating Facility. Each panel test article included a metallic separation bolt imbedded in Orion compression-pad and heatshield materials, resulting in a circular protuberance over a flat plate. The protuberances produce complex model flowfields, containing shock-shock and shock-boundary layer interactions, and multiple augmented heating regions on the test plate. As part of the test calibration runs, surface pressure and heat flux measurements on water-cooled calibration plates integrated with the wedge models were also obtained. Surface heating distributions on the test articles as well as arc-jet test environment parameters for each test configuration are obtained through computational fluid dynamics simulations, consistent with the facility and calibration measurements. The present analysis comprises simulations of the nonequilibrium flowfield in the facility nozzle, test box, and flowfield over test articles, and comparisons with the measured calibration data.

CFD↗

CFD Simulations of the IHF Arc-Jet Flow: Compression-Pad Separation Bolt Wedge Tests

This paper reports computational analyses in support of two wedge tests in a high enthalpy arc-jet facility at NASA Ames Research Center. These tests were conducted using two different wedge models, each placed in a free jet downstream of a corresponding different conical nozzle in the Ames 60-MW Interaction Heating Facility. Each panel test article included a metallic separation bolt imbedded in Orion compression-pad and heatshield materials, resulting in a circular protuberance over a flat plate. The protuberances produce complex model flowfields, containing shock-shock and shock-boundary layer interactions, and multiple augmented heating regions on the test plate. As part of the test calibration runs, surface pressure and heat flux measurements on water-cooled calibration plates integrated with the wedge models were also obtained. Surface heating distributions on the test articles as well as arc-jet test environment parameters for each test configuration are obtained through computational fluid dynamics simulations, consistent with the facility and calibration measurements. The present analysis comprises simulations of the non-equilibrium flow field in the facility nozzle, test box, and flow field over test articles, and comparisons with the measured calibration data.

CFD↗

THE STELLAR STRUCTURE AND KINEMATICS OF DWARF SPHEROIDAL GALAXIES FORMED BY TIDAL STIRRING

Using high-resolution N-body simulations, we study the stellar properties of dwarf spheroidal (dSph) galaxies resulting from the tidally induced morphological transformation of disky dwarfs on a cosmologically motivated eccentric orbit around the Milky Way. The dwarf galaxy models initially consist of an exponential stellar disk embedded in an extended spherical dark matter halo. Depending on the initial orientation of the disk with respect to the orbital plane, different final configurations are obtained. The least evolved dwarf is triaxial and retains a significant amount of rotation. The more evolved dwarfs are prolate spheroids with little rotation. We show that in this scenario the final density distribution of stars can be approximated by a simple modification of the Plummer law. The kinematics of the dwarfs is significantly different depending on the line of sight which has important implications for mapping the observed stellar velocity dispersions of dwarfs to subhalo circular velocities. When the dwarfs are observed along the long axis, the measured velocity dispersion is higher and decreases faster with radius. In the case where rotation is significant, when viewed perpendicular to the long axis, the effect of minor axis rotation is detected, as expected for triaxial systems. We model the velocity dispersion profiles and rotation curves of the dwarfs under the assumption of constant mass-to-light ratio by solving the Jeans equations for spherical and axisymmetric systems and adjusting different sets of free parameters, including the total mass. We find that the mass is typically overestimated when the dwarf is seen along the long axis and underestimated when the observation is along the short or intermediate axis. For the studied cases, the effect of non-sphericity cannot, however, bias the inferred mass by more than 60% in either direction, even for the most strongly stripped dwarf which is close to disruption.

79 ASTRONOMY AND ASTROPHYSICS↗

Stability and control characteristics of a monoplanar elliptic missile model at Mach numbers from 1.60 to 2.86

An investigation was conducted of a monoplanar maneuverable missile concept having a nose forebody with a circular cross section and a centerbody and afterbody with elliptical cross sections. The tests involved several component changes and were conducted in the low Mach number test section of the Langley Unitary Plan wind tunnel at Mach numbers of 1.60, 2.16, and 2.86, at angles of attack ranging from -4 degs to 28 degs and at sideslip angles ranging from -4 degs to 8 degs. The most significant result was that at the highest Mach number (2.86), the configuration with the infrared nose produced nearly twice the axial force as the same configuration with the radar nose. The cranked wing had a destabilizing effect on the longitudinal stability and had no effect on the lateral-directional stability. The nose strakes had no effect longitudinally and were detrimental to the lateral-directional stability.

Sawyer, W. C.↗

Mars Ascent Vehicle Flight Analysis

The scientific objective of the Mars Surveyor Program 2005 mission is to return Mars rock, soil, and atmospheric samples to Earth for detailed analysis. The present investigation focuses on design of Mars Ascent Vehicle for this mission. Aerodynamic, aerothermodynamic, and trajectory design considerations are addressed to assess the ascent configuration, determine aerodynamic stability, characterize thermal protection system requirements, and ascertain the required system mass. Aerodynamic analysis reveals a subsonic static instability with the baseline configuration; however, stability augmentation options are proposed to mitigate this problem. The ascent aerothermodynamic environment is shown to be benign (on the order of the sea-level boiling point of water on Earth). As a result of these low thermal and pressure loads, a lightweight, low rigidity material can be employed as the aftbody aerodynamic shroud. The required nominal MAV lift-off mass is 426 kg for a December 2006 equatorial launch into a 300-km circular orbit with 30-degree inclination. Off-nominal aerodynamic and atmospheric conditions are shown to increase this liftoff mass by approximately 10%. Through performance of these analyses, the Mars Ascent Vehicle is deemed feasible with respect to the current mission mass and size constraints.

Desai, P. N.↗

Crossflow Mixing of Noncircular Jets

An experimental investigation has been conducted of the isothermal mixing of a turbulent jet injected perpendicular to a uniform crossflow through several different types of sharp-edged orifices. Jet penetration and mixing was studied using planar Mie scattering to measure time-averaged mixture fraction distributions of circular, square, elliptical, and rectangular orifices of equal geometric area injected into a constant velocity crossflow. Hot-wire anemometry was also used to measure streamwise turbulence intensity distributions at several downstream planes. Mixing effectiveness was determined using (1) a spatial unmixedness parameter based on the variance of the mean jet concentration distributions and (2) by direct comparison of the planar distributions of concentration and of turbulence intensity. No significant difference in mixing performance was observed for the six configurations based on comparison of the mean properties.

Liscinsky, D. S.↗

Mars Ascent Vehicle Hybrid Propulsion Configuration

As part of a Mars Sample Return (MSR) campaign, two Mars Ascent Vehicle (MAV) configurations have been designed in parallel. Each ascent vehicle configuration has a different propulsion system which ultimately leads to two unique vehicle designs. As part of a Preliminary Architecture Assessment (PAA), these vehicle designs were developed to the same level of maturity in order to inform the selection of one of the vehicles as the point of departure design for the campaign. The selection will be made in November 2019. The initial MSR architecture called for a hybrid-based propulsion MAV. This type of propulsion system calls for a solid wax motor that would utilize liquid MON-25 as an oxidizer. Hybrid rocket propulsion allows for more flexibility than traditional solid or liquid propulsion options, and typically benefits from the advantages of both. A hybrid motor can be throttled and shut down easily, and avoids significant risk in manufacturing and handling. On a theoretical level, hybrid motors perform at a higher specific impulse (Isp) than solid motors. The primary disadvantage of hybrid motors comes from additional complexity and significantly less flight heritage and low Technology Readiness Level (TRL). This paper describes the design of the hybrid propulsion configuration. An additional paper will be published describing the design of the solid propulsion configuration1. The hybrid propulsion configuration MAV was developed in 2019 by NASA Marshall Space Flight Center (MSFC) in association with NASA Jet Propulsion Laboratory (JPL). It features a Single Stage to Orbit (SSTO) design with an SP7A solid wax fuel and MON-25 liquid oxidizer. The liquid portion of the vehicle allows for a Liquid Injection Thrust Vector Controller (LITVC) as well as hypergolic propellant additives for ignition. The vehicle was designed to deliver approximately 0.31kg of Martian geological samples to a circular orbit at Mars of 343km at a 25o inclination. Although hybrid propulsion in general has been used on launch vehicles in the past, the integrated vehicle subsystems that operate in conjunction with these propulsion elements do not typically operate in a Martian environment, which in this application can get as cold as -40oC. The PAA advanced the maturity of these subsystems by performing detailed design and analysis on the vehicle with respect to structures and mechanisms, Guidance/Navigation/Control (GNC) systems, avionics, Reaction Control System (RCS), LITVC, thermal environments, and advanced Computational Fluid Dynamics (CFD). This paper will summarize the results of these studies.

Yaghoubi, Darius↗

A numerical study of capillary stability in a circular cylindrical container with a concave spheroidal bottom

The paper describes a theoretical investigation of the stability under gravitational and surface forces of a liquid in a circular cylindrical container with a concave spheroidal bottom for the case in which the volume of the liquid is sufficiently small so that the bottom is not covered completely. The gravitational field is assumed to be directed along the symmetry axis of the container, and for a specific container shape the critical Bond number is calculated as a function of liquid volume for contact angles of gamma = 0, 1, 2, and 4 deg. For gamma = 0 deg, some critical equilibrium configurations and corresponding perturbation modes are presented.

Concus, P.↗

Region-of-interest image reconstruction in circular cone-beam microCT

Cone-beam microcomputed tomography (microCT) is one of the most popular choices for small animal imaging which is becoming an important tool for studying animal models with transplanted diseases. Region-of-interest (ROI) imaging techniques in CT, which can reconstruct an ROI image from the projection data set of the ROI, can be used not only for reducing imaging-radiation exposure to the subject and scatters to the detector but also for potentially increasing spatial resolution of the reconstructed images. Increasing spatial resolution in microCT images can facilitate improved accuracy in many assessment tasks. A method proposed previously for increasing CT image spatial resolution entails the exploitation of the geometric magnification in cone-beam CT. Due to finite detector size, however, this method can lead to data truncation for a large geometric magnification. The Feldkamp-Davis-Kress (FDK) algorithm yields images with artifacts when truncated data are used, whereas the recently developed backprojection filtration (BPF) algorithm is capable of reconstructing ROI images without truncation artifacts from truncated cone-beam data. We apply the BPF algorithm to reconstructing ROI images from truncated data of three different objects acquired by our circular cone-beam microCT system. Reconstructed images by use of the FDK and BPF algorithms from both truncated and nontruncated cone-beam data are compared. The results of the experimental studies demonstrate that, from certain truncated data, the BPF algorithm can reconstruct ROI images with quality comparable to that reconstructed from nontruncated data. In contrast, the FDK algorithm yields ROI images with truncation artifacts. Therefore, an implication of the studies is that, when truncated data are acquired with a configuration of a large geometric magnification, the BPF algorithm can be used for effective enhancement of the spatial resolution of a ROI image.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Modal focal adaptive optics for Bessel-focus two-photon fluorescence microscopy

Adaptive optics (AO) improves the spatial resolution of microscopy by correcting optical aberrations. While its application has been well established in microscopy modalities utilizing a circular pupil, its adaptation to systems with non-circular pupils, such as Bessel-focus two-photon fluorescence microscopy (2PFM) with an annular pupil, remains relatively uncharted. Herein, we present a modal focal AO (MFAO) method for Bessel-focus 2PFM. Measuring and correcting aberration using a spatial light modulator placed in conjugation with the focal plane of the microscope objective, MFAO employs Zernike annular polynomials — a first in AO implementation — to achieve performance on par with a previous zonal AO method, but with a notably simplified optical configuration. We validated the performance of MFAO in correcting artificial and sample-induced aberrations, as well as in in vivo imaging of zebrafish larvae and mouse brains. By expanding the application of modal AO to annular pupils as well as aberration measurement and correction to a wavefront modulator at the objective focal plane, MFAO represents a notable advancement in the implementation of AO in microscopy.

47 OTHER INSTRUMENTATION↗

Radiation pattern synthesis of planar antennas using the iterative sampling method

A synthesis method is presented for determining an excitation of an arbitrary (but fixed) planar source configuration. The desired radiation pattern is specified over all or part of the visible region. It may have multiple and/or shaped main beams with low sidelobes. The iterative sampling method is used to find an excitation of the source which yields a radiation pattern that approximates the desired pattern to within a specified tolerance. In this paper the method is used to calculate excitations for line sources, linear arrays (equally and unequally spaced), rectangular apertures, rectangular arrays (arbitrary spacing grid), and circular apertures. Examples using these sources to form patterns with shaped main beams, multiple main beams, shaped sidelobe levels, and combinations thereof are given.

Stutzman, W. L.↗

Electromagnetic backscattering from a layer of vegetation - A discrete approach

Electromagnetic backscattering from a layer of vegetation over a flat lossy ground is studied. The vegetated region is composed of leaves which are modeled by lossy circular dielectric discs with prescribed orientation statistics. The mean field in the layer is computed by using the Foldy approximation and a two-variable technique which is valid for small fractional volume. Simple expressions are given for the skin depth of the mean wave. Following this, the distorted Born approximation is used to calculate the co-polarized and cross polarized backscattering coefficients. These are then computed as a function of angle of incidence for different layer depths and leaf configurations.

Lang, R. H.↗

Global coverage Mobile Satellite Systems: System availability versus channel propagation impairments

Mobile Satellite Systems (MSS) in Highly Elliptical (HEO) and circular Earth orbits at Medium (MEO) and Low (LEO) altitudes have been intensively studied in the last few years as an effective means of providing global communication services. Such global coverage MSS networks are also expected to mitigate typical channel impairments usually encountered in geostationary Land Mobile Satellite (LMS) systems. In the design stages of these satellite networks, information regarding the mobile propagation channel is needed to assess the overall link availability versus elevation angle and environmental scenarios. For multisatellite LMS configurations, the mobile user on the Earth surface sees, at any given time, more than one satellite of the constellation. In our paper, it is shown that, under certain working assumptions regarding the statistics of the propagation channel, an improvement of the link availability may be achieved through the use of a multisatellite constellation. The analyses have been carried out using the European Space Agency (ESA) LMS propagation data base which presently covers a wide range of elevation angles and environmental scenarios.

Sforza, M.↗

The protoplanetary disc around HD 169142: circumstellar or circumbinary?

ABSTRACT Stellar binaries represent a substantial fraction of stellar systems, especially among young stellar objects. Accordingly, binaries play an important role in setting the architecture of a large number of protoplanetary discs. Binaries in coplanar and polar orientations with respect to the circumbinary disc are stable configurations and could induce non-axisymmetric structures in the dust and gas distributions. In this work, we suggest that the structures shown in the central region of the protoplanetary disc HD 169142 are produced by the presence of an inner stellar binary and a circumbinary (P-type) planet. We find that a companion with a mass ratio of 0.1, semimajor axis of 9.9 au, eccentricity of 0.2, and inclination of 90°, together with a 2 MJ coplanar planet on a circular orbit at 45 au reproduce the structures at the innermost ring observed at 1.3 mm and the shape of spiral features in scattered light observations. The model predicts changes in the disc’s dust structure, and star’s astrometric parameters, which would allow testing its veracity by monitoring this system over the next 20 yr.

79 ASTRONOMY AND ASTROPHYSICS↗