Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Beam Simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Beam Measurements of the Tianlai Dish Radio Telescope using an Unmanned Aerial Vehicle

Precision measurement of the beam pattern of an antenna is very important for many applications. While traditionally such measurement is often made in a microwave anechoic chamber or at a test range, measurement using an unmanned aerial vehicle offers a number of advantages: the measurement can be made for the assembled antenna on site, thus reflecting the actual characteristics of the antenna of interest, and more importantly, it can be performed for larger antennas which cannot be steered or easily measured using the anechoic chamber and test range. Here we report our beam measurement experiment with UAV for a 6 meter dish used in the Tianlai array, which is a radio astronomy experiment. Due to the dish's small collecting area, calibration with an astronomical source only allows for determining the antenna beam pattern over a very limited angular range. We describe in detail the setup of the experiment, the components of the signal transmitting system, the design of the flight path and the procedure for data processing. We find the UAV measurement of the beam pattern agrees very well with the astronomical source measurement in the main lobe, but the UAV measurement can be extended to the fourth side lobe. The measured position and width of each lobe also shows good agreement with electromagnetic field simulation. This UAV-based approach of beam pattern measurement is flexible and inexpensive, and the technique may also be applied to other experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRSDate not supplied

NASA Space Radiation Laboratory Galactic Cosmic Ray Simulator

With exciting new Agency plans for a sustainable return to the moon, astronauts will once again leave earth’s protective magnetosphere only to endure higher levels of radiation from galactic cosmic rays (GCR) and the possibility of a large solar particle event (SPE). Gateway, lunar landers, and surface habitats will be designed to protect crew against SPEs with vehicle optimization, storm shelter concepts, and/or active dosimetry; however, the ever-penetrating GCR will continue to pose the most significant health risks especially as lunar missions increase in duration and as NASA sets its aspirations on Mars. The primary risks of concern include carcinogenesis, central nervous system effects resulting in potential in-mission cognitive or behavioral impairment and/or late neurological disorders, degenerative tissue effects including cataracts, circulatory and heart disease, as well as, potential immune system decrements impacting multiple aspects of crew health. Characterization and mitigation of these risks requires a significant reduction in the large biological uncertainties of chronic (low-dose rate) heavy ion exposures and the validation of countermeasures in a relevant space environment. NASA has developed the “GCR Simulator” at Brookhaven National Laboratory to generate a spectrum of ion beams that approximates the primary and secondary GCR field experienced at human organ locations within a deep-space vehicle. The majority of the dose is delivered from protons (~65-75%) and helium ions (~10-20%) with heavier ions (Z>3) contributing the remainder. The “GCR Simulator” exposes state-of-the art cellular and animal model systems to 33 sequential beams including 4 proton energies plus degrader, 4 helium energies plus degrader, and the five heavy ions of C, O, Si, Ti, and Fe. A polyethylene degrader is used with the 100 MeV/n H and He beams to provide a nearly continuous distribution of low energy particles. A 500 mGy exposure, delivering doses from each of the 33 beams, requires 75-90 minutes. To more closely simulate the low dose rates found in space, sequential field exposures can be divided into daily fractions over 2-6 weeks, with individual beam fractions as low as 0.1-0.2 mGy. In the large beam configuration (60 x 60 cm2), 54 special housing cages can accommodate 2-3 mice each for a 70-75 min duration or ~15 individually housed rats. Emerging research results from our 2018 runs utilizing mixed heavy ion fields and protracted space exposures are forthcoming and will deepen our understanding of the numerous health risks faced by astronauts. This talk discusses NASA’s innovative technology solution for a ground-based GCR simulator at the NASA Space Radiation Laboratory to enable future exploration missions.

galactic cosmic ray simulator↗
DOE OSTI2022

SPACE: 3D parallel solvers for Vlasov-Maxwell and Vlasov-Poisson equations for relativistic plasmas with atomic transformations

A parallel, relativistic, three-dimensional particle-in-cell code SPACE has been developed for the simulation of electromagnetic fields, relativistic particle beams, and plasmas. In addition to the standard second-order Particle-in-Cell (PIC) algorithm, SPACE includes efficient novel algorithms to resolve atomic physics processes such as multi-level ionization of plasma atoms, recombination, and electron attachment to dopants in dense neutral gases. SPACE also contains a highly adaptive particle-based method, called Adaptive Particle-in-Cloud (AP-Cloud), for solving the Vlasov-Poisson problems. It eliminates the traditional Cartesian mesh of PIC and replaces it with an adaptive octree data structure. The code's algorithms, structure, capabilities, parallelization strategy, and performance have been discussed. Additionally, typical examples of SPACE applications to accelerator science and engineering problems are described.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Design of Silicide-Strengthened Nb–Si–Cr–(Mo) alloys for additive manufacturing

Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nonlinear models for coupling the effects of stimulated Raman scattering to inertial confinement fusion codes

Laser plasma instabilities (LPI) reduce driver-target coupling, alter implosion symmetry, and therefore can fundamentally limit fusion performance in inertial confinement fusion (ICF). Developing a predictive modeling capability for LPI effects can critically advance the success of the field. We perform vector particle-in-cell simulations of multi-speckled laser beams undergoing stimulated Raman scattering (SRS) at various densities and intensities relevant to mainly indirectly driven and a subset of parameter space for directly driven ICF systems, focusing on the regimes with intensities above the onset of electron trapping. Based on the wavenumber of the SRS daughter electron plasma wave, we identify several regions with underpinning SRS saturation physics: the electron-trapping dominated region with intermediate kλD values, the strong Landau damping region at larger kλD values, and the region where the Langmuir decay instability arises at lower kλD values. We develop a nonlinear SRS reflectivity model that features the base trapping-dominated scaling of (kλD)−4 and its modifications. Electron trapping deforms the initialized electron distribution functions, and we have developed a new δf-Gaussian-mixture algorithm for an accurate characterization of the trapped hot electron population. With this SRS hot electron description, we construct a nonlinear energy deposition model and a hot electron source model—based on a modified Manley–Rowe relation—suitable for including SRS effects as a sub-grid module in a high-fidelity ICF design code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Electron cyclotron emission quasi-optical transmission system on the HL-3 tokamak

A new quasi-optical (QO) Electron Cyclotron Emission (ECE) transmission system has been established on the HL-3 tokamak, which includes a focusing QO mirror combination and a long-distance transmission line. This system was developed to meet the requirements for poloidal spatial resolution and the high signal-to-noise ratio needed for magnetohydrodynamic (MHD) instability studies using ECE on the HL-3. The QO mirror combination was installed inside the vacuum chamber for focusing. Laboratory test results, theoretical calculations, and synthetic ECE simulation results indicate that the Gaussian beam can meet the spatial resolution requirements for the accurate measurement of the MHD instability on the q = 1/2/3 surfaces, corresponding to the poloidal mode numbers m = 3/6/9. This includes good diagnostic poloidal spatial resolution for the important 2/1 and 3/2 modes. At the front end of the transmission line, a high-efficiency mode converter was designed to transition the TE 10 mode to the HE 11 mode for input into the transmission line, with an insertion loss of less than 1.5 dB. A 30 m long-distance corrugated oversized waveguide was constructed, with transmission losses ranging from 6 to 10 dB in the 60–120 GHz range. Polarization adjustment results show that the polarization offset and geometric spatial polarization angle change consistently, which can provide a reference for polarization adjustment in other complex structured transmission lines. As a result, the newly established ECE QO transmission system will provide strong support for future physics research involving ECE on the HL-3.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Focusing of laser-accelerated ions with spherically curved targets

A theoretical model for laser-accelerated ion focusing from spherically curved targets using a Gaussian self-similar solution is presented. This model describes the evolution of the focal location and focal radius with final ion energy and the initial radial boundary of the ions, the latter being a function of both target geometry and the ion acceleration radius for a given ion energy. The theory is supported by particle-in-cell simulations of a variety of target shapes with varying radii of curvature and target opening angles, as well as variations in the injected electron beam radius and energy spectrum. The theory and simulations suggest that the focal location varies linearly with the radius of curvature, with the square root of the ratio of ion energy to effective electron temperature, and monotonically increases with the energy-dependent ratio of the initial ion radial boundary to the radius of curvature. Considering ponderomotive acceleration, this suggests that the focal length should scale inversely with intensity, $(I_Lλ_L^2)$ −1/4 , suggesting a 10× increase in intensity will reduce the focal distance by ̃1.8× for a given ion energy.

Physics - Plasma physics↗
DOE OSTI2021

High yield polar direct drive fusion neutron sources at the National Ignition Facility

Polar direct drive neutron source experiments were performed at the National Ignition Facility showing substantial improvement in total neutron yield and efficiency of conversion of laser energy to fusion output. Plastic capsules 3–4 mm in diameter were filled with 1.5 mg/cc of deuterium–tritium (DT) fuel and imploded with laser beam pointing and defocus designed to compensate for polar asymmetry introduced by the facility beam entrance angles. Radiation-hydrodynamics simulations were employed to optimize the multi-dimensional laser and target parameter space, within facility and target fabrication constraints. Ensembles of 1D simulations tuned to match the outputs of early shots in the series were used to design subsequent shots in the series. This allowed the later shots to be designed based on empirically motivated sensitivities to laser and target input parameters, while eliminating the need to explicitly model phenomena such as hydrodynamic instabilities and nonlinear laser–plasma interactions. Additionally, one experiment with a 3.0 mm diameter CH capsule produced 13.6 kJ (4.81 × 10 15 DT neutrons) from a laser input below the NIF optics damage threshold at 585 kJ, 328 TW. Two experiments with 4.0 mm capsules produced 31.3 and 33.6 kJ of fusion output (1.11 × 10 16 and 1.19 × 10 16 DT neutrons) with 1.10 MJ, 390 TW and 1.26 MJ, 425 TW of laser input, respectively.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Modeling the effect of MHD activity on runaway electron generation during SPARC disruptions

Magnetohydrodynamic (MHD) instabilities and runaway electrons (REs) interact in several ways, making it important to self-consistently model these interactions for accurate predictions of RE generation and the design of mitigation strategies, such as massive gas injection (MGI). Using M3D-C1 – an extended MHD code with a RE fluid model – we investigate the effects of 3-D nonlinear MHD activity, material injection, and 2-D axisymmetric vertical displacement events (VDEs) on RE evolution during disruptions on SPARC – a high-field, high-current tokamak designed to achieve a fusion gain Q > 1. Several cases, comprising different combinations of neon (Ne) and deuterium (D 2 ) injection, are considered. Here, our results demonstrate key effects that arise from the self-consistent RE + MHD coupling, such as an initial increase in RE generation due to MHD instability growth, decreased saturation energies of the m/n = 1/1 mode driving sawteeth-like activity, RE losses in stochastic magnetic fields, and subsequent RE confinement and plateau formation due to re-healing of flux surfaces. Large RE plateaus (>5 MA) are obtained with Ne-only injection (2-5 × 10 21 atoms), while combined D 2 + Ne injection (2 × 10 21 Ne atoms; 1.8 × 10 22 D 2 molecules) produces a lower RE current (<2 MA). With D 2 + Ne injection, a post thermal quench "cold" VDE terminates the RE beam, preventing a steady plateau. These simulations couple REs, 3-D MHD instabilities, MGI, and axisymmetric VDEs for the first time in SPARC disruption simulations and represent a crucial step in understanding RE generation and mitigation in high-current devices like SPARC.

Datta, Rishabh [Massachusetts Inst. of Technology ↗
DOE OSTI2020

Direct drive with the argon fluoride laser as a path to high fusion gain with sub-megajoule laser energy

Argon fluoride (ArF) is currently the shortest wavelength laser that can credibly scale to the energy and power required for high gain inertial fusion. ArF's deep ultraviolet light and capability to provide much wider bandwidth than other contemporary inertial confinement fusion (ICF) laser drivers would drastically improve the laser target coupling efficiency and enable substantially higher pressures to drive an implosion. Our radiation hydrodynamics simulations indicate gains greater than 100 are feasible with a sub-megajoule ArF driver. Our laser kinetics simulations indicate that the electron beam-pumped ArF laser can have intrinsic efficiencies of more than 16%, versus about 12% for the next most efficient krypton fluoride excimer laser. We expect at least 10% ‘wall plug' efficiency for delivering ArF light to target should be achievable using solid-state pulsed power and efficient electron beam transport to the laser gas that was demonstrated with the U.S. Naval Research Laboratory's Electra facility. These advantages could enable the development of modest size and lower cost fusion power plant modules. This would drastically change the present view on inertial fusion energy as being too expensive and the power plant size too large.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Synthesis and characterization of electron beam irradiation-induced damage in polycrystalline metal thin films

High-energy physics research, industrial sterilizing, and material processing depend extensively on electron beam accelerators. Exit windows are crucial components of such electron accelerator systems, maintaining vacuum integrity inside the machine while providing mechanical strength, thermal stability, and radiation resistance at the beam-target interface. In this study, thin metallic films of Ni, Ti, Cr, and V were explored for use in electron beam exit windows, and their properties were compared with the properties of their bulk counterparts. Simulation results of metal foils predicted Ti to exhibit less beam power dissipation compared to Ni. However, Ni possesses superior mechanical and structural properties compared to Ti. The performance of these films under electron beam irradiation was examined by depositing thin layers of these films on silicon and metallic substrates using magnetron sputtering and exposing them to e-beam irradiation in a controlled setup. The deposited films were subjected to a dose of approximately 66 kGy at a beam energy of 10 MeV and characterized prior to and postexposure to the beam using field emission scanning electron microscopy, atomic force microscopy, x-ray diffraction (XRD), and nanoindentation. Particular emphasis was given to characteristics like the grain structure, surface morphology, dislocation density, and hardness. XRD patterns revealed irradiation-induced changes in peak intensities, while the crystallinity remained largely unchanged. Nanoindentation results showed that the pristine and irradiated Ti and Ni films were twice as hard when compared to bulk Ti and Ni samples, regardless of the substrate type used (Si or bulk Ti, or Ni). These results emphasize the superior mechanical properties of thin metal films compared to their bulk counterparts. In conclusion, this study advances the optimization of thin film materials for robust and efficient e-beam applications, ensuring improved durability and operational reliability.

AFM↗
DOE OSTI2020

Pressurized Gas Beam Monitor for Extremely High Intensities – Phase II

A novel pressurized gas-filled multi-RF-cavity beam profile monitor has been studied that is simple and robust in high-radiation environments. Charged particles passing through each RF-cavity in the monitor produce intensity-dependent ionized plasma, which changes the gas permittivity. Standard RF techniques to measure the change in quality factor (Q) and frequency (f) as a function of time are then used to determine the change in permittivity and corresponding beam intensity in each cavity in the profile monitor. The sensitivity to beam intensity is adjustable using gas pressure and RF gradient. The performance of the gas-filled beam profile monitor has been numerically simulated to evaluate the sensitivity of permittivity measurements and the effectiveness of calibration strategies. An entire multi-RF-cavity system has been designed and a demonstration test has been prepared.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Plasma Photonics for the Control of Kilojoule Lasers

The main goal of this project was to develop plasma photonic devices (plasma lenses or ellipsoidal plasma mirrors (EPMs)) for controlling the focus of high-energy (kJ-class) laser systems. In order to defocus a kJclass laser beam, a plasma optic must produce a very specific plasma density profile. For a plasma lens, this profile must be peaked on axis and fall off parabolicly with radius. We developed four plasma-lens target designs that were predicted to yield the ideal plasma profile required for defocusing kJ-class laser beams. Particle-in-cell (PIC) simulations using the code OSIRIS were used to explore the design. The resulting plasma lens must also be underdense, which sets an upper limit on the solid density of the plasma-lens targets to ~ 1 mg/cm 3 or less. This low of a density is highly challenging to fabricate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Summer Student Internship: Experimental and modeling experiences

My internship at the Los Alamos National Laboratory has been an information-filled summer. Loren Espada-Castillo brought me into her project and helped mentor and guide me through the summer. The project that I was brought into was the process of shooting materials with electrons. The electron beam we used conducts a series of shots in which electrons are generated and then fired towards a target, the sample holder. The sample holder holds either a single sample or three samples. The sample holder also consists of multiple calorimeters surrounding the sample/s. The goal is to shoot certain materials and then analyze how they react to the exposure of the electrons. We shot titanium, which was meant to serve as a containment vessel window.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling Codes Used for LAMP

LAMP team is planning on using multiple computer codes as tools for modeling beam dynamics, electromagnetics, and plasma environment in ion sources. Below is a description of the computer tools we have been using or planning to use in the future. Most of the codes chosen for the LAMP project are capable to model most of the beam dynamics in LAMP. A judicious choice of the appropriate code to use will be based on speed and fidelity of the modeling with faster calculations produced by simplifying some features.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Commissioning of Phase 1 of the LANL RFQ Test Stand - Beam Characterization

A series of numerical start-to-end simulations of Phase 1 of the 750 keV RFQ Test Stand which includes the ion source (H+ duoplasmatron), a 1-Solenoid LEBT, an emittance scan station and a Faraday cup were performed to find a mechanism for the characterization of the proton beam extracted from the duoplasmatron.

43 PARTICLE ACCELERATORS↗