SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Typical testing experience in cryogenic wind tunnels

Airfoil testing as a major activity of many wind tunnels is considered, and emphasis is placed on airfoil testing with sidewall boundary-layer removal, oscillating airfoil testing, and three-dimensional wake topology. Buffeting as the structural response of an aircraft or test model to the aerodynamic excitation produced by separated flows is analyzed, as well as flutter problems and testing techniques. Strain-gage balance studies, optical methods and visualization techniques, and fluid mechanics are examined. Focus is placed on a two-spot laser as a boundary-layer probe, hot-film gages, fluctuating-pressure measurements, skin-friction balance, and nonadiabatic airfoil testing. Boattail afterbody pressure tests are covered, and Space Shuttle Orbiter base drag and launch configuration are discussed.

Kilgore, Robert A.↗

NASA NTRS1997

Neural Network Research on Tilt-Rotor Hover Performance

Results from a neural network study on XV-15 tilt-rotor hover performance are presented. Two XV-15 test data bases, acquired during separate tests conducted in the National Full-Scale Aerodynamics Complex at NASA Ames, were used in this study. The two XV-15 test data bases used were: the 1997 80- by 120-Foot Wind Tunnel test data base and the 1984 Outdoor Aerodynamic Research Facility (OARF) test data base. The objectives associated with the 80- by 120-Foot Wind Tunnel test data were to conduct data quality checks, obtain neural network representations, and demonstrate sensitivity to test conditions. The objectives associated with the OARF outdoor test data were to obtain a 'zero wind' neural network representation, and formulate and implement a neural network based wind correction procedure. An additional objective, common to both test data bases, was to conduct error comparisons. The conclusions from the present study were as follows: Compared to measured parameters (i.e., collective pitch angle), derived parameters (i.e., thrust coefficient) were found preferable as neural network inputs. For the 80- by 120-Foot Wind Tunnel test data base, the neural network based figure of merit representations did not extrapolate rotor stall. Using the OARF outdoor test database, a neural network based wind correction procedure was formulated and successfully implemented. Based on an error comparison, the present neural network based wind correction procedure was found to be more accurate compared to the existing, momentum-theory-based wind correction procedure. Also, a separate error comparison showed that the 80- by 120-Foot Wind Tunnel hover performance data were comparable to non-wind-corrected outdoor test data.

Kozapalli, S.↗

NASA NTRS1983

Analysis and correlation of the test data from an advanced technology rotor system

Comparisons were made of the performance and blade vibratory loads characteristics for an advanced rotor system as predicted by analysis and as measured in a 1/5 scale model wind tunnel test, a full scale model wind tunnel test and flight test. The accuracy with which the various tools available at the various stages in the design/development process (analysis, model test etc.) could predict final characteristics as measured on the aircraft was determined. The accuracy of the analyses in predicting the effects of systematic tip planform variations investigated in the full scale wind tunnel test was evaluated.

Jepson, D.↗

NASA NTRS1987

High-resolution heat-transfer-coefficient maps applicable to compound-curve surfaces using liquid crystals in a transient wind tunnel

Tests were performed in a transient heat transfer tunnel in which the model under test was preheated prior to allowing room temperature air to be suddenly drawn over the model. The resulting movement of isothermal contours on the model is revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record is obtained of a temperature and time data pair for all points on the model during a single test. Experiments on a duct model are reported in which the model was preheated using a hot air stream. A manner in which initial model temperature nonuniformities could be taken into account was investigated. The duct model was also tested with a steady-state measurement technique and results were compared with the transient measurements, but recognizing that differences existed between the upstream thermal boundary conditions. The steady-state and transient measurements were shown to be consistent with predicted values. The main advantage of this transient heat transfer technique using liquid crystals is that since the test model need not be actively heated, high-resolution measurements on surfaces with complex shapes may be obtained.

Jones, T. V.↗

NASA NTRS1988

High-resolution heat-transfer-coefficient maps applicable to compound-curve surfaces using liquid crystals in a transient wind tunnel

Jones, Terry V.↗

NASA NTRS1976

Correlation of low speed wind tunnel and flight test data for V/STOL aircraft

The availability of wind tunnel test data for correlation purposes of the same V/STOL aircraft tested in flight is very limited. This is due in a large part to size limitations of wind tunnels and the number of wind tunnels available for testing of full-scale aircraft. Wind tunnel tests are described for two research aircraft - the XV-5B fan-in-wing aircraft and the YOV-10 RCF (rotating cylinder flap) aircraft - in the NASA Ames 40- by 80-foot wind tunnel. The tests were conducted specifically to provide for correlation between wind tunnel and in-flight aerodynamics and noise test data. Correlation between aerodynamic and noise data are presented and testing techniques that are related to the accuracy of the data, or that might affect the correlations, are discussed. The correlation of noise measurements made with a J-85 engine mounted on a F-106 aircraft during low altitude flyovers with the same J-85 engine mounted on a model and tested in the Ames 40- by 80-foot wind tunnel are also reported.

Cook, W. L.↗

NASA NTRS1971

Aerodynamic characteristics of Lockheed delta-body orbiter and stage-and-one-half launch vehicle

An experimental wind tunnel test program was conducted to investigate the subsonic through high supersonic aerodynamic characteristics of the Lockheed delta lifting body orbiter and stage-and-one-half launch vehicle. Analyses and results of these data are presented. A 0.01-scale model of the LS 200-5 system was designed and fabricated for testing in wind tunnels. Orbiter and launch configurations were tested over a speed range of Mach 0.6 to 2.0, whereas only the orbiter was tested over a speed range of Mach 2.3 to 4.6. Six-component force and moment data, base pressures, and schlieren photos were obtained at various angles-of-attack and sideslip. A 0.03-scale model of the orbiter was also designed, fabricated, and tested in a wind tunnel. Six-component force and moment data, base pressure, and a limited amount of tuft flow visualization data were obtained on a variety of configuration combinations.

Velligan, F. A.↗

NASA NTRS2000

Recent Cycle Time Reduction at Langley Research Center

The NASA Langley Research Center (LaRC) has been engaged in an effort to reduce wind tunnel test cycle time in support of Agency goals and to satisfy the wind tunnel testing needs of the commercial and military aerospace communities. LaRC has established the Wind Tunnel Enterprise (WTE), with goals of reducing wind tunnel test cycle time by an order of magnitude by 2002, and by two orders of magnitude by 2010. The WTE also plans to meet customer expectations for schedule integrity, as well as data accuracy and quality assurance. The WTE has made progress towards these goals over the last year with a focused effort on technological developments balanced by attention to process improvements. This paper presents a summary of several of the WTE activities over the last year that are related to test cycle time reductions at the Center. Reducing wind tunnel test cycle time, defined here as the time between the freezing of loft lines and delivery of test data, requires that the relationship between high productivity and data quality assurance be considered. The efforts have focused on all of the drivers for test cycle time reduction, including process centered improvements, facility upgrades, technological improvements to enhance facility readiness and productivity, as well as advanced measurement techniques. The application of internet tools and computer modeling of facilities to allow a virtual presence of the customer team is also presented.

Kegelman, Jerome T.↗

NASA NTRS1999

NASA/FAA Tailplane Icing Program Overview

The effects of tailplane icing were investigated in a four-year NASA/FAA Tailplane Icing, Program (TIP). This research program was developed to improve the understanding, of iced tailplane aeroperformance and aircraft aerodynamics, and to develop design and training aides to help reduce the number of incidents and accidents caused by tailplane icing. To do this, the TIP was constructed with elements that included icing, wind tunnel testing, dry-air aerodynamic wind tunnel testing, flight tests, and analytical code development. This paper provides an overview of the entire program demonstrating the interconnectivity of the program elements and reports on current accomplishments.

Ratvasky, Thomas P.↗

NASA NTRS1999

In-Flight Aerodynamic Measurements of an Iced Horizontal Tailplane

The effects of tailplane icing on aircraft dynamics and tailplane aerodynamics were investigated using, NASA's modified DHC-6 Twin Otter icing research aircraft. This flight program was a major element of the four-year NASA/FAA research program that also included icing wind tunnel testing, dry-air aerodynamic wind tunnel testing, and analytical code development. Flight tests were conducted to obtain aircraft dynamics and tailplane aerodynamics of the DHC-6 with four tailplane leading-edge configurations. These configurations included a clean (baseline) and three different artificial ice shapes. Quasi-steady and various dynamic flight maneuvers were performed over the full range of angles of attack and wing flap settings with each iced tailplane configuration. This paper presents results from the quasi-steady state flight conditions and describes the range of flow fields at the horizontal tailplane, the aeroperformance effect of various ice shapes on tailplane lift and elevator hinge moment, and suggests three paths that can lead toward ice-contaminated tailplane stall. It was found that wing, flap deflection was the most significant factor in driving the tailplane angle of attack toward alpha(tail stall). However, within a given flap setting, an increase in airspeed also drove the tailplane angle of attack toward alpha(tail stall). Moreover, increasing engine thrust setting also pushed the tailplane to critical performance limits, which resulted in premature tailplane stall.

Ratvasky, Thomas P.↗

NASA NTRS2012

An Overview of the Semi-Span Super-Sonic Transport (S4T) Wind-Tunnel Model Program

A summary of computational and experimental aeroelastic (AE) and aeroservoelastic (ASE) results for the Semi-Span Super-Sonic Transport (S4T) wind-tunnel model is presented. A broad range of analyses and multiple AE and ASE wind-tunnel tests of the S4T wind-tunnel model have been performed in support of the ASE element in the Supersonics Program, part of the NASA Fundamental Aeronautics Program. This paper is intended to be an overview of multiple papers that comprise a special S4T technical session. Along those lines, a brief description of the design and hardware of the S4T wind-tunnel model will be presented. Computational results presented include linear and nonlinear aeroelastic analyses, and rapid aeroelastic analyses using CFD-based reduced-order models (ROMs). A brief survey of some of the experimental results from two open-loop and two closed-loop wind-tunnel tests performed at the NASA Langley Transonic Dynamics Tunnel (TDT) will be presented as well.

Silva, Walter A.↗

NASA NTRS1974

Measurement of tilt rotor VTOL rotor wake-airframe ground aerodynamic interference for application to real time flight simulation

The hover and low speed rotor wake-airframe-ground aerodynamic characteristics of the XV-15 tilt rotor research aircraft were determined in wind tunnel tests of a scale model. Results of the wind tunnel tests were applied to real flight time simulation. The principal findings of the wind tunnel tests are summarized. The effect of aerodynamic interference on the handling qualities of the aircraft is analyzed. It was determined that aerodynamic interference effects are significant in hover and at low speeds, with the influence being more pronounced in ground effect than out of it. At airspeeds above 60 knots, aerodynamic interference does not have a significant effect on handling characteristics.

Gaffey, T. M.↗

NASA NTRS2020

USM3D Analyses in Support of the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel Test of Boundary-Layer Thickener Configurations

A wind tunnel test was performed in the 0.3-Meter Cryogenic Transonic Tunnel at the NASA Langley Research Center to investigate the impact of various boundary layer thickeners on the height and shape of the boundary layer on the aft portion of a semispan fuselage. The present work discusses USM3D analyses that were performed in support of the wind tunnel test. The results consisted of comparisons between USM3D and experimental data for the baseline configuration and two boundary layer thickening configurations. The comparisons considered surface pressure distributions, boundary layer profiles, and calculated boundary layer thicknesses. Additionally, a grid refinement study was performed for each of the three configurations, which illustrated general improvement in the comparisons with increasing grid refinement. Overall, the comparisons show favorable agreement between the USM3D predictions and the experimental data.

Bozeman, Michael D., Jr.↗

NASA NTRS2016

Pre-Test Assessment of the Use Envelope of the Normal Force of a Wind Tunnel Strain-Gage Balance

The relationship between the aerodynamic lift force generated by a wind tunnel model, the model weight, and the measured normal force of a strain-gage balance is investigated to better understand the expected use envelope of the normal force during a wind tunnel test. First, the fundamental relationship between normal force, model weight, lift curve slope, model reference area, dynamic pressure, and angle of attack is derived. Then, based on this fundamental relationship, the use envelope of a balance is examined for four typical wind tunnel test cases. The first case looks at the use envelope of the normal force during the test of a light wind tunnel model at high subsonic Mach numbers. The second case examines the use envelope of the normal force during the test of a heavy wind tunnel model in an atmospheric low-speed facility. The third case reviews the use envelope of the normal force during the test of a floor-mounted semi-span model. The fourth case discusses the normal force characteristics during the test of a rotated full-span model. The wind tunnel model's lift-to-weight ratio is introduced as a new parameter that may be used for a quick pre-test assessment of the use envelope of the normal force of a balance. The parameter is derived as a function of the lift coefficient, the dimensionless dynamic pressure, and the dimensionless model weight. Lower and upper bounds of the use envelope of a balance are defined using the model's lift-to-weight ratio. Finally, data from a pressurized wind tunnel is used to illustrate both application and interpretation of the model's lift-to-weight ratio.

strain-gage balance↗

NASA NTRS1989

Main results of CAST-10 airfoil tested in T2 cryogenic wind tunnel

The aim of this cooperative NASA/DFVLR/ONERA project was to examine the performance of the CAST-10 airfoil in the T2 cryogenic wind tunnel. Tests included general characteristics of the CAST-10 airfoil and fundamental studies on Reynold number effects. Good T2 cryogenic operation was observed. Improvements should be done for moisture elimination and for side wall boundary layer effects.

Blanchard, A.↗

NASA NTRS1991

Aerodynamics of spheres for Mach numbers from 0.6 to 10.5 including some effects of test conditions

Wind tunnel tests were made for spheres of various sizes over a range of Mach numbers and Reynolds numbers. The results indicated some conditions where the drag was affected by changes in the afterbody pressure due to a shock reflection from the tunnel wall. This effect disappeared when the Mach number was increased for a given sphere size or when the sphere size was decreased for a given Mach number. Drag measurements and Schlieren photographs show the possibility of obtaining inaccurate data when tests are made with a sphere too large for the test section size and Mach number. Tests were also made of an oblate spheroid. The results indicated a region at high Mach numbers where inherent positive static stability might occur with the oblate-face forward. The drag results are compared with those for a sphere and those for various other shapes. The drag results for the oblate spheriod and the sphere are also compared with some calculated results.

Spearman, M. Leroy↗

NASA NTRS1992

Flutter suppression digital control law design and testing for the AFW wind tunnel model

Design of a control law for simultaneously suppressing the symmetric and antisymmetric flutter modes of a sting mounted fixed-in-roll aeroelastic wind tunnel model is described. The flutter suppression control law was designed using linear quadratic Gaussian theory, and involved control law order reduction, a gain root-locus study and use of previous experimental results. A 23 percent increase in the open-loop flutter dynamic pressure was demonstrated during the wind tunnel test. Rapid roll maneuvers at 11 percent above the symmetric flutter boundary were also performed when the model was in a free-to-roll configuration.

Mukhopadhyay, Vivek↗

NASA NTRS1994

Flutter suppression digital control law design and testing for the AFW wind tunnel model

The design of a control law for simultaneously suppressing the symmetric and antisymmetric flutter modes of a sting mounted fixed-in-roll aeroelastic wind-tunnel model is described. The flutter suppression control law was designed using linear quadratic Gaussian theory, and it also involved control law order reduction, a gain root-locus study, and use of previous experimental results. A 23 percent increase in the open-loop flutter dynamic pressure was demonstrated during the wind-tunnel test. Rapid roll maneuvers at 11 percent above the symmetric flutter boundary were also performed when the model was in a free-to-roll configuration.

Mukhopadhyay, Vivek↗