Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “walls”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Turbulent transport modeling of shear flows around an aerodynamic wing. Development of turbulent near-wall model and its application to recirculating flows

Progress in implementing and refining two near-wall turbulence models in which the near-wall region is divided into either two or three zones is outlined. These models were successfully applied to the computation of recirculating flows. The research was further extended to obtaining experimental results of two different recirculating flow conditions in order to check the validity of the present models. Two different experimental apparatuses were set up: axisymmetric turbulent impinging jets on a flat plate, and turbulent flows in a circular pipe with a abrupt pipe expansion. It is shown that generally better results are obtained by using the present near-wall models, and among the models the three-zone model is superior to the two-zone model.

Amano, R. S.↗
NASA NTRS1983

Construction and test of flexible walls for the throat of the ILR high-speed wind tunnel

Aerodynamic tests in wind tunnels are jeopardized by the lateral limitations of the throat. This influence expands with increasing size of the model in proportion to the cross-section of the throat. Wall interference of this type can be avoided by giving the wall the form of a stream surface that would be identical to the one observed during free flight. To solve this problem, flexible walls that can adapt to every contour of surface flow are needed.

Igeta, Y.↗
NASA NTRS1982

Wall interference evaluation from pressure measurements on control surfaces

Conventional methods for the calculation of wall interference corrections are based on boundary conditions which require a knowledge of ventilated wall porosity parameters, and which are unsuitable for deformed walls. The method described uses a simple exponential decay of pressure distribution beyond the most upstream and downstream limits in order to evaluate Mach number and incidence corrections given by the method proposed by Papelier et al. (1978). It is found that, while the upstream contribution to incidence correction is significant, the upstream and downstream contributions to Mach number correction are negligible.

Gopinath, R.↗
NASA NTRS1983

Contouring tunnel walls to achieve free-air flow over a transonic swept wing

The effects of wind-tunnel walls on the flow over a swept wing were greatly reduced by wall contouring. Significant reductions in spanwise pressure gradients were achieved by shaping all of the walls to conform to the streamlines over the model in free air. Surface pressure and oil-flow data were used to evaluate the effects of Mach and Reynolds numbers on the design. Comparisons of these data with inviscid calculations indicate that free-air flow is established at a Mach number of 0.74 and at Reynolds numbers above 4.7 million.

Mateer, G. G.↗
NASA NTRS1983

Wall-function boundary conditions in the solution of the Navier-Stokes equations for complex compressible flows

To make computer codes for two-dimensional compressible flows more robust and economical, wall functions for these flows, under adiabatic conditions, have been developed and tested. These wall functions have been applied to three two-equation models of turbulence. The tests consist of comparisons of calculated and experimental results for transonic and supersonic flow over a flat plate and for two-dimensional and axisymmetrical transonic shock-wave/boundary-layer interaction flows with and without separation. The calculations are performed with an implicit algorithm that solves the Reynolds-averaged Navier-Stokes equations. It is shown that results obtained agree very well with the data for the complex compressible flows tested, provided criteria for use of the wall functions are followed. The expected savings in cost of the computations and improved robustness of the code were achieved.

Viegas, J. R.↗
NASA NTRS1981

Effect of driven-wall motion on a turbulent boundary layer

An acoustically driven wall model with amplitudes greater than 0.01 cm was used to study the effect of unsteady wall boundary conditions on the structure of a zero-pressure-gradient turbulent boundary layer. Hot-wire measurements showed large variations in fluctuation quantities (including Reynolds stress) along each model wave. These longitudinal variations decreased rapidly with increasing distance from the driven wall, but the average level of these fluctuations decreased only slightly even outside the boundary layer. When the acoustical fluctuations were subtracted, the remaining fluctuations were essentially the same as for the undriven model. It is concluded that there is no significant interaction between the acoustic and turbulent fluctuations.

Weinstein, L. M.↗
NASA NTRS1984

TWINTN4: A program for transonic four-wall interference assessment in two-dimensional wind tunnels

A method for assessing the wall interference in transonic two-dimensional wind tunnel tests including the effects of the tunnel sidewall boundary layer was developed and implemented in a computer program named TWINTN4. The method involves three successive solutions of the transonic small disturbance potential equation to define the wind tunnel flow, the equivalent free air flow around the model, and the perturbation attributable to the model. Required input includes pressure distributions on the model and along the top and bottom tunnel walls which are used as boundary conditions for the wind tunnel flow. The wall-induced perturbation field is determined as the difference between the perturbation in the tunnel flow solution and the perturbation attributable to the model. The methodology used in the program is described and detailed descriptions of the computer program input and output are presented. Input and output for a sample case are given.

Kemp, W. B., Jr.↗
NASA NTRS1984

Isolation and characterization of beta-glucan synthase: A potential biochemical regulator of gravistimulated differential cell wall loosening

In plants, gravity stimulates differential growth in the upper and lower halves of horizontally oriented organs. Auxin regulation of cell wall loosening and elongation is the basis for most models of this phenomenon. Auxin treatment of pea stem tissue rapidly increases the activity of Golgi-localized Beta-1,4-glucan synthase, an enzyme involved in biosynthesis of wall xyloglucan which apparently constitutes the substrate for the wall loosening process. The primary objective is to determine if auxin induces de novo formation of Golgi glucan synthase and increases the level of this glucan synthase mRNA. This shall be accomplished by (a) preparation of a monoclonal antibody to the synthase, (b) isolation, and characterization of the glucan synthase, and (c) examination for cross reactivity between the antibody and translation products of auxin induced mRNAs in pea tissue. The antibody will also be used to localize the glucan synthase in upper and lower halves of pea stem tissue before, during and after the response to gravity.

Kuzmanoff, K. M.↗
NASA NTRS1984

Scaling and modeling of three-dimensional, end-wall, turbulent boundary layers

The method of matched asymptotic expansion was employed to identify the various subregions in three dimensional, turbomachinery end wall turbulent boundary layers, and to determine the proper scaling of these regions. The two parts of the b.l. investigated are the 3D pressure driven part over the endwall, and the 3D part located at the blade/end wall juncture. Models are proposed for the 3d law of the wall and law of the wake. These models and the data of van den Berg and Elsenaar and of Mueller are compared and show good agreement between models and experiments.

Goldberg, U. C.↗
NASA NTRS1984

Computation of imaginary-side pressure distributions over the flexible walls of the test section insert for the 0.3-M transonic cryogenic tunnel

Two dimensional airfoil testing in an adaptive wall test-section wind tunnel requires the computation of the imaginary flow fields extending outward from the top and bottom test section walls. A computer program was developed to compute the flow field which would be associated with an arbitrary test section wall shape. The program is based on incompressible flow theory with a Prandtl-Glauert compressibility correction. The program was validated by comparing the streamline and the pressure field generated by a source in uniform flow with the results from the computer program. A listing of the program, the validation test results, and a sample program are included.

Goodyer, M. J.↗
NASA NTRS1984

Electroless-plating technique for fabricating thin-wall convective heat-transfer models

A technique for fabricating uniform thin-wall metallic heat-transfer models and which simulates a Shuttle thermal protection system tile is described. Two 6- by 6- by 2.5-in. tiles were fabricated to obtain local heat transfer rates. The fabrication process is not limited to any particular geometry and results in a seamless thin-wall heat-transfer model which uses a one-wire thermocouple to obtain local cold-wall heat-transfer rates. The tile is relatively fragile because of the brittle nature of the material and the structural weakness of the flat-sided configuration; however, a method was developed and used for repairing a cracked tile.

Avery, D. E.↗
NASA NTRS1984

Development of a turbulence near-wall model and its application to separated and reattached flows

A numerical study is reported of flow and heat transfer in the separated and reattached flows created by an abrupt pipe expansion. In the study attention has been given primarily to the development of turbulence near-wall models based on the wall function. An efficient numerical method is also employed for the computation of high-velocity flows. The computed results are compared with experimental data obtained earlier. Generally, better results are obtained by employing the present near-wall models, and among them the three-layer model is superior to the two-layer one.

Amano, R. S.↗
NASA NTRS1984

Propagation and radiation of sound from flanged circular ducts with circumferentially varying wall admittances. I Semi-infinite ducts. II - Finite ducts with sources

Sound propagation in infinite, semiinfinite, and finite circular ducts with circumferentially varying wall admittances is investigated analytically. The infinite case is considered, and an example demonstrates the effects of wall-admittance distribution on dispersion characteristics and mode shapes. An exact solution is obtained for the semiinfinite case, a circular duct with a flanged opening: sidelobe suppression and circumferential-mode energy scattering leading to radiated-field asymmetry are found. A finite duct system with specified hard-walled pressure sources is examined in detail, evaluating reflection coefficients, transmission losses, and radiated-field directivity. Graphs and diagrams are provided, and the implications of the results obtained for the design of aircraft-turbofan inlet liners are discussed.

Fuller, C. R.↗
NASA NTRS1984

Pressure-strain correlations in curved wall boundary layers

Pressure-strain correlations, which represent some part of production and dissipation of Reynolds stress in turbulent wall-bounded shear layers, have been determined for the cases of boundary layer flow past a convex, a concave and a flat wall, the latter also in the case when it follows a convex wall (relaxing flow). The Large Eddy Interaction Model utilized for prediction also permits determination of the contribution from different parts of the turbulence spectra to the correlations in different parts across the boundary layer. The relation between the anisotropic nature of the correlations and the spectra in the different flow cases provides a means of testing models for the correlations.

Hong, S. K.↗
NASA NTRS1985

Side Shield for Wall Support

Method employs curved shield on each side of mining machine. In stowed position, shield folded against roof-support columns on one side. In deployed position, shield raised and braced against coal-seam wall by hydraulic cylinder. Shield supports wall until roof and wall properly secured by bolting and cement coating.

Lewis, E. V.↗
NASA NTRS1985

Curtain Wall Creates Ventilation Channel

Curtain-wall structure proposed for removing methane and airborne coal dust from hydrojet-jaw mining machines. Channel between curtain wall and mine wall forms closed exhaust passage. Through it, gas and dust continuously removed so high concentrations of these explosive materials not build up.

Lewis, E. V.↗