SEARCH · Engineering Papers

Results for “torque”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

All sources NASA NTRS DOE OSTI

NASA NTRS1976

OH-58 helicopter transmission failure analysis

The OH-58 main transmission gearbox was run at varying output torques, speeds, and oil cooling rates. The gearbox was subsequently run to destruction by draining the oil from the gearbox while operating at a speed of 6200 revs per minute and 36,000 inch-pounds output torque. Primary cause of gearbox failure was overheating and melting of the planet bearing aluminum cages. Complete failure of the gearbox occurred in 28 1/2 minutes after the oil pressure dropped to zero. The alternating and maximum stresses in the gearbox top case were approximately 10 percent of the endurance limit for the material. Deflection of the bevel gear at 67000 inch-pounds output torque indicate a marginal stiffness for the bevel gear supporting system.

Townsend, D. P.↗

NASA NTRS1975

Satellite attitude prediction by multiple time scales method

An investigation is made of the problem of predicting the attitude of satellites under the influence of external disturbing torques. The attitude dynamics are first expressed in a perturbation formulation which is then solved by the multiple scales approach. The independent variable, time, is extended into new scales, fast, slow, etc., and the integration is carried out separately in the new variables. The theory is applied to two different satellite configurations, rigid body and dual spin, each of which may have an asymmetric mass distribution. The disturbing torques considered are gravity gradient and geomagnetic. Finally, as multiple time scales approach separates slow and fast behaviors of satellite attitude motion, this property is used for the design of an attitude control device. A nutation damping control loop, using the geomagnetic torque for an earth pointing dual spin satellite, is designed in terms of the slow equation.

Tao, Y. C.↗

NASA NTRS1977

A CW ultrasonic bolt-strain monitor

There exists a need for a relatively inexpensive system for measuring strain in bolts. The torque wrench is one technique for straining bolts which has been widely applied. Unfortunately, friction in the bolt threads and between the nut and the work tend to make such a simple system inaccurate. In practice, a torque wrench is unacceptable for many situations where strain is critical. In this article, an ultrasonic technique is described which can indicate changes in bolt strain to better than one part in 10,000. The technique is based on the one-dimensional propagating-ultrasonic-wave model and uses a new ultrasonic instrument called a Reflection Oscillator Ultrasonic Spectrometer which is a closed-loop feedback marginal-oscillator system that frequency locks the device to the peak of a mechanical resonance in the bolt. The instrument indicates a shift in the bolt resonance frequency due to elongation and changes in velocity of sound due to strain. Data are presented comparing a standard torque wrench to the ultrasonic monitor for different measured stresses on the bolt as well as for different bolt conditions. The strain instrument can be used to monitor changing stresses, to measure material properties and may be applied as a strain gage or load cell.

Heyman, J. S.↗

NASA NTRS1978

Methods of attenuating wind turbine ac generator output variations

Wind speed variation, tower blockage and structural and inertial factors produce unsteady torque in wind turbines. Methods for modifying the turbine torque so that steady torque is delivered to the coupled ac generator are discussed. The method that may evolve will be influenced by the power use that develops and the trade-offs of cost, weight and complexity.

Gold, H.↗

NASA NTRS1978

Analytic investigation of advancing blade drag reduction by tip modifications

Analytic techniques were applied to study the effect on the performance of the nonlifting advancing blade when the outboard 5% of the blade is modified to reduce drag. The tip modifications studied consisted of reducing airfoil thickness, sweepback, and planform taper. The reductions in instantaneous drag and torque were calculated for tip speed ratios from about 0.19 to 0.30, corresponding to advancing blade tip Mach numbers of 0.855 to 0.936, respectively. Approximations required in the analysis introduce uncertainties into the computed absolute values of drag and torque; however, the differences in the quantities should be a fairly reliable measure of the effect of changing tip geometry. For example, at the highest tip speed, instantaneous drag, and torque were reduced by 20% and 24%, respectively, for tip sweep of 40 deg on a blade using an NACA 0010 airfoil and by comparable amounts for 30-deg sweep on a blade having an NACA 0012 airfoil section. The present method should prove to be a useful, inexpensive technique for identifying promising configurations for additional study and testing.

Tauber, M. E.↗

NASA NTRS1980

Bolt-bearing fatigue of a graphite/epoxy laminate

Graphite/epoxy laminates were tested under bolt-bearing loads for a range of bolt clampup torques and for several test conditions involving water. High clampup torque improved both the static strength and fatigue limit by about 100 percent compared to a simple pin-bearing case, which had no through-the-thickness constraint. The static strength improvement was explained in terms of failure modes. Bolt clampup also influenced the hole elongation that developed before failure. For both the static and fatigue tests, the hole elongations were much larger for the low-torque clampup. Tests in water degraded static bearing strength only slightly, but reduced the fatigue limit about 40 percent below that for tests conducted in air.

Crews, J. H., Jr.↗

NASA NTRS1980

Manipulation of large objects

Remote manipulator control experiments have been conducted to investigate the problems related to the 'controlled collision' aspect of manipulation. A six degrees of freedom pantograph arm with a six-dimensional force-torque balance sensor and microprocessor-driven real-time graphics display are employed in the experiments. Among other results, it is found that the use of computer force-torque feedback loop for 'stop at contact' provides a nearly linear relation between load transfer to jigs at 'stop at contact', rate of motion, and preset force-torque threshold values for stop under limited motion and load conditions.

Bejczy, A. K.↗

NASA NTRS1980

Nonlinear attitude dynamics of satellites

A study of predicting the rotational motion of a rigid body satellite orbiting the earth under the influence of external torques is presented. The attitude motion in response to external torques is formulated as a perturbation from a nominal torque-free case; the equations of motion are parameterized by the ratio of the orbital and attitude frequencies. The independent variable time is extended into a space of higher dimension by using new fast and slow scales. The theory is applied for predicting the attitude dynamics of an asymmetric rigid-body satellite.

Ramnath, R. V.↗

NASA NTRS1982

New Apparatus Tests Pressure-Suit Joints

New apparatus measures applied torque and angle-of-flexure in pressurized flexible joints, such as those found in diving suits and flight suits. Torque and flexure are permanently recorded on x-y plotter. Family of curves can be taken as function of suit pressure or other variables. Apparatus could also measure torque-versus-angle in mechanical linkages.

Vykukal, H. C.↗

NASA NTRS1981

A drive unit for the instrument pointing system

The requirements, capabilities, and unique design features of the instrument pointing system drive units (DU) are presented. The DU's are identical for all three gimbal axes (elevation, cross elevation, and azimuth) and provide alternating rotation of shaft versus the housing of + or - 180 deg. The design features include: two ball bearing cartridges using cemented carbide balls coated with TiC a layer; redundant brushless torque motors and resolvers; a load by-pass mechanism driven by a dc torque motor to off-load the bearings during ascent/descent, ground transportation, and to provide an emergency breaking capability; and cabling over each gimbal axis by means of cable follow-up consisting of 13 signal and 15 power flat band cable loops. Test results of disturbance torque characteristics are presented.

Birner, R.↗

NASA NTRS1980

Orbit-averaged behavior of magnetic control laws for momentum unloading

Analytical formulas are derived for orbit-averaged behavior of magnetic control laws for unloading the excess angular momentum of a spacecraft reaction wheel control system in the presence of secular environmental torques. The specific example of an axially symmetric spacecraft with an inertially fixed attitude for which the dominant environmental torque is the gravity-gradient torque is treated in detail, but extensions of the general approach to other inertially fixed and earth-pointing spacecraft are discussed. The analytical formulas are compared to detailed simulations performed for the Solar Maximum Mission spacecraft, and agreement to within 10% is found. The analytical formulas can be used in place of detailed simulations for preliminary studies, and can be used to find selected cases giving the most stringent tests of momentum unloading capability for which detailed simulations may be performed.

Camillo, P. J.↗

NASA NTRS1982

Two-Speed Valve

Operating torque adjustment of two-speed valve provided by preload spring and nut. Torque is adjusted so user finds valve easy to turn but does not turn it too quickly during fast-moving portion of valve stem travel. Drive pin transmits torque to differential nut.

Drapeau, D. F.↗

NASA NTRS1981

Experimental results with a six-degree-of-freedom force-reflecting hand controller

Control experiments performed using an isotonic joystick connected to a six degree-of-freedom manipulator equipped with a six dimensional force-torque sensor at the base of the manipulator end effector are described. The preliminary control experiments were aimed at the investigation of the human operators' ability to command and control forces in different directions by varying the information conditions and the values of the feedforward and feedback command gains in the bilateral control loop. The main conclusions are: (1) a quantified graphic display of force-torque information can considerably enhance the operator's ability to perform a quantitatively sharp force-torque control, and (2) there seems to be a task dependent optimal combination of the feedforward and feedback command gain values which provide a dynamically smooth and stable bilateral control performance.

Bejczy, A. K.↗

NASA NTRS1982

Magnetic field control

A torque control for an electromechanical torquing device of a type where a variable clearance occurs between a rotor and field is described. A Hall effect device senses the field present, which would vary as a function of spacing between field and rotor. The output of the Hall effect device controls the power applied to the field so as to provide a well defined field and thus a controlled torque to the rotor which is well defined.

Haeussermann, W.↗

NASA NTRS1982

Pressure suit joint analyzer

A measurement system for simultaneously measuring torque and angular flexure in a pressure suit joint is described. One end of a joint under test is held rigid. A torque transducer is pivotably supported on the other movable end of a joint. A potentiometer is attached to the transducer by an arm. The wiper shaft of the potentiometer is gripped by a reference arm that rotates the wiper shaft the same angle as the flexure of joint. A signal is generated by the potentiometer which is representative of the joint flexure. A compensation circuit converts the output of the transducer to a signal representative of joint torque.

Vykukal, H. C.↗

NASA NTRS1982

The 100-meter radiometer spacecraft study

A rigid body analysis of a baseline Large Space System (LSS) which is to function as a radiometer is presented. The LSS is placed in circular orbit about the Earth at an altitude of 650 km, subjected to environmental and vehicle interaction forces and torques, without an active control system of any type on board. The environment forces and torques are gravity gradient, solar radiation, and aerodynamic. Normal operation is in nadir pointing along the Z-local vertical axis. Orbital velocity is assigned to the x-axis of the spacecraft. The analysis is then used to demonstrate the ability or lack of the gravity gradient torques to stabilize the LSS over one complete orbit.

Zimbelman, H. F.↗

NASA NTRS1982

A cryogenic valve for spacecraft applications

Space-compatible cryogenic valves are now required to operate between room and liquid helium temperatures. A remotely controllable cryogenic valve is described, which is made of bellows-type stainless steel and is operated by a miniature dc motor with integral gearset (485:1) at a nominal voltage of 28 Vdc. The power transmission provides a further reduction of 7.2:1 to give an overall gear ratio of nearly 3500:1, assuring reliability of operation at low temperatures. Valve performance (leak rate) data are presented at LN2, LHe, and SfHe temperatures at delivered torques of 18, 27, 31, and 35 N-m. At a closing torque of 31 N-m, a leak rate of 0.028 scc/sec was achieved at 2 K, while at a torque of 18 N-m the leak rate at 300 K was less than 3 x 10 to the -9th scc/sec.

Salerno, L. J.↗

NASA NTRS1982

A parametric study of the behavior of the angular momentum vector during spin rate changes of rigid body spacecraft

During a spin-up or spin-down maneuver of a spinning spacecraft, it is usual to have not only a constant body-fixed torque about the desired spin axis, but also small undesired constant torques about the transverse axes. This causes the orientation of the angular momentum vector to change in inertial space. Since an analytic solution is available for the angular momentum vector as a function of time, this behavior can be studied for large variations of the dynamic parameters, such as the initial spin rate, the inertial properties and the torques. As an example, the spin-up and spin-down maneuvers of the Galileo spacecraft was studied and as a result, very simple heuristic solutions were discovered which provide very good approximations to the parametric behavior of the angular momentum vector orientation.

Longuski, J. M.↗