Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solution processable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Case Study for Lunar ISRU Systems Utilizing Polar Water

In-Situ Resource Utilization (ISRU) is key to long term presence at any extraterrestrial destination. Current NASA direction is to achieve a sustainable presence on the lunar surface by 2028. Mission plans currently target the lunar South Pole to leverage the extended periods of solar illumination and allows for potential access to water ice in the permanently shadowed areas around the poles. With water, it is possible to produce both fuel and oxidizer to fully refuel a vehicle. In order to address ISRU infusion into mission planning, a study of an end-to-end ISRU propellant production system was initiated to assess ISRU architectures and obtain mass and power estimates for each. The results of these case studies will be presented. For this study, The ISRU system architecture involved two sites; the mine site in a shadowed crater where water ice is excavated and extracted from the regolith and the propellant production site at an illuminated ridge where the water is processed into liquefied O2 and H2 propellants. Fixed hardware would be emplaced at each site, with two alternating water tankers to transport water between them. Notional lunar sites were identified for this architecture for baseline environmental parameters. Technology solutions for each subsystem were selected based on those with the highest fidelity models or those that have empirical laboratory data to anchor to. While power needs were identified for each location, a power solution was not prescribed, therefore the masses presented do not include surface power systems. The baseline case in this study assumed that 10 mT of oxygen, along with enough hydrogen to support a propulsion mixture ratio of 6, must be produced in 225 days. Therefore 15 mT of water would need to be collected and processed. The baseline solution resulted in a system mass of5 mT and a total required power of 68kW. The majority of the mass was split between the ridge site system and the two water tankers (2.6 mTand 1.8mTrespectively). The majority of the required power was with three subsystems at approximately 20 kW each: hydrogen liquefaction, electrolysis, and the water extractor subsystem. Trades for four key variables are also presented, namely production rate, water concentration, dry overburden depth, and number of water transport trips. This can be compared to a system that targets oxygen from the minerals in the surface regolith material. A carbothermal reduction reactor system was used for this comparison. The use of direct solar thermal energy to process the regolith and the ease of access of the resource resulted in significantly lower values for the oxygen case: approximately 2.7 mT and 11.8 kW. However, the mass trade would favor the water case over successive missions where the hydrogen up-mass of 2 mT per mission will accrue against the oxygen system.1Aerospace Research Engineer, Chemical and Thermal Propulsion Systems Branch, Senior Member.2Mechanical Engineer, Propulsion and Power Division/Energy Conversion Systems, 2101 Nasa Pkwy/Mailcode EP3 Houston, TX 77058, AIAA member.

Lunar↗
NASA NTRS1979

A viscous flow analysis of the tip vortex generation process

A viscous primary-secondary flow analysis designed for numerical solution by forward marching integration is applied to the tip vortex generation problem. Equations governing streamwise momentum, streamwise vorticity, and a gas law are solved in conjunction with equations governing scalar and vector surface potentials for the secondary velocities. The numerical method used combines a consistently split linearized block implicit (LBI) scheme for parabolic equations and a scalar iterative ADI scheme for elliptic equations. Computed results are presented for a wing of rectangular planform immersed in a high Reynolds number stream at 6 degrees incidence. The physical mechanism for generation of the tip vortex, as revealed by the analysis and computations, is discussed. Detailed flow results for the case of 6 degree incidence are included.

Shamroth, S. J.↗
NASA NTRS1991

Characterization of the corrosion resistance of biologically active solutions: The effects of anodizing and welding

An understanding of fabrication processes, metallurgy, electrochemistry, and microbiology is crucial to the resolution of microbiologically influenced corrosion (MIC) problems. The object of this effort was to use AC impedance spectroscopy to characterize the corrosion resistance of Type II anodized aluminum alloy 2219-T87 in sterile and biologically active media and to examine the corrosion resistance of 316L, alloy 2219-T87, and titanium alloy 6-4 in the welded and unwelded conditions. The latter materials were immersed in sterile and biologically active media and corrosion currents were measured using the polarization resistance (DC) technique.

Walsh, Daniel W.↗
NASA NTRS2020

Application of IRIG 106 Digital Data Recorder Standards for Flight Test

During flight tests, data is acquired from different sources and in different formats. Sensor data, aircraft avionics bus data, time, voice and video are essential for analysis of these flight tests. IRIG 106 standards exist for recording and transferring these data types. However, to enhance interoperability of flight test data between (multinational) test teams, a standard was needed to encapsulate all these data types. For this purpose the Telemetry Group of the Range Commanders Council (RCC) first published in 2004 the IRIG 106 Chapter 10 Standard, “Solid-State On-Board Recorder Standard”. This standard is evolving up to present. This AGARDograph gives an introduction to the standard, explains how the standard is positioned among other relevant standards, and describes the equipment and their application in flight tests with some examples. The topics covered include IRIG 106 Chapter 10 compatible recording of (multiple) data streams, synchronization of data, data recorders, data retrieval, data processing, and examples of flight test programs. Further development of the standard, originally published for on-board recorders, is described for extending the requirements for ground-based data recorders. The last chapter addresses a number of issues related to the application of the Chapter 10 standard with references to information and possible solutions. This document shows how data acquisition and data processing in accordance to IRIG 106 Chapter 10 standard can be applied in NATO flight tests and will thereby contribute to collaboration and cost efficiency.

flight test instrumentation↗
NASA NTRS1986

Transition from a planar interface to cellular and dendritic structures during rapid solidification processing

The development of theoretical models which characterize the planar-cellular and cell-dendrite transitions is described. The transitions are analyzed in terms of the Chalmers number, the solute Peclet number, and the tip stability parameter, which correlate microstructural features and processing conditions. The planar-cellular transition is examined using the constitutional supercooling theory of Chalmers et al., (1953) and it is observed that the Chalmers number is between 0 and 1 during dendritic and cellular growth. Analysis of cell-dendrite transition data reveal that the transition occurs when the solute Peclet number goes through a minimum, the primary arm spacings go through a maximum, and the Chalmers number is equal to 1/2. The relation between the tip stability parameter and the solute Peclet number is investigated and it is noted that the tip stability parameter is useful for studying dendritic growth in alloys.

Laxmanan, V.↗
NASA NTRS1990

An efficient design sensitivity analysis of eigenvectors

Subspace iteration has been a major advance in solving large eigen problems when only a subset of eigen-pairs is required. The essence of this method is a transformation from displacement coordinates of an n-th order eigensystem to generalized coordinates of a smaller q-th order. The eigenvalue problem is then solved in the reduced space. The method was first developed by Clint and Jennings for real symmetric systems and was then called 'simultaneous iteration'. The success of the method prompted further research along this line and there have been many improved algorithms developed. This approach has been widely used by structural engineers for extracting the most useful natural frequencies and mode shapes of large-scale dynamic systems. This paper exploits into a new direction which is in the form of iterative process for simultaneously calculating eigenvector derivatives of many eigenvectors with respect to multi-variables. The method fully uses all the available information from preceding eigenvalue solution and, thus, effectively economizes computational efforts. It iterates through two equations derived from the first variation of the two fundamental equations used in subspace iteration method. There is no expensive large matrix decomposition required and the process converges to acceptable solution in a finite number of iterations. Therefore, the procedure increases its efficiency superiority over the others as the system size or the number of interested eigenvectors become larger and larger.

Ting, T.↗
NASA NTRS1982

Solidification of undercooled liquids

During rapid solidification processing (RSP) the amount of liquid undercooling is an important factor in determining microstructural development by controlling phase selection during nucleation and morphological evolution during crystal growth. While undercooling is an inherent feature of many techniques of RSP, the deepest undercoolings and most controlled studies have been possible in carefully prepared fine droplet samples. From past work and recent advances in studies of nucleation kinetics it has become clear that the initiation of crystallization during RSP is governed usually by heterogeneous sites located at surfaces. With known nucleant sites, it has been possible to identify specific pathways of metastable phase formation and microstructural development in alloys. These advances have allowed for a clearer assessment of the interplay between undercooling, cooling rate and particle size statistics in structure formation. New approaches to the examination of growth processes have been developed to follow the thermal behavior and morphology in small samples in the period of rapid crystallization and recalescence. Based upon the new experimental information from these studies, useful models can be developed for the overall solidification process to include nucleation behavior, thermodynamic constraints, thermal history, growth kinetics, solute redistribution and resulting structures. From the refinement of knowledge concerning the underlying factors that govern RSP a basis is emerging for an effective alloy design and processing strategy.

Perepezko, J. H.↗
NASA NTRS1972

Response of convectively controlled burning to nonlinear disturbances.

A process where energy release rate is proportional to the square root of the Reynolds number of a burning particle or surface is used to demonstrate some distinctive dynamic properties of a disturbed convectively controlled burning process. The instantaneous energy release rates caused by assumed periodic flow field disturbances are numerically evaluated and examined. Correlation coefficients which express the energy released in-phase with the pressure disturbance are evaluated and analytical solutions for these coefficients are derived. The response of the process is shown to be highly sensitive to the harmonic distortion of the disturbance. For some disturbances the energy released in-phase with the pressure disturbance is an order of magnitude larger than that for linear (sinusoidal) disturbances. The results show that harmonic distortion increases the coupling between the burning process and the flow field. This amplifying effect of harmonic distortion is suppressed when a disturbance becomes steep-fronted; therefore, steepening can act to limit the equilibrium amplitudes in disturbed systems. Amplification is also suppressed when the velocity disturbance is phase shifted with respect to the pressure disturbance or when the process is exposed to a high steady velocity.

Heidmann, M. F.↗
NASA NTRS2022

Plasma Assisted Nutrient Recovery from Inedible Biomass via Ash Leaching

Sustaining a human presence on the Moon, Mars, or deep space will require closing loops on many life support systems. Some form of agriculture will be required because plants produce the vitamins, antioxidants, and essential oils in our diets that degrade over time in stored foods. In addition, they provide dietary fiber, restore air, and purify water. Growing plants will require recycling nutrients trapped in inedible vegetation. Researchers at KSC have investigated the use of a thermal plasma with various carrier gases to thermally degrade inedible plant biomass for nutrient recovery. Previous work demonstrated a thermally degrading environment such as a muffle furnace improved nutrient recovery from inedible biomass prior to an acid leaching process. However, a muffle furnace is an inefficient process. We have explored the use of a small scale, thermal plasma for degradation of pellets to enhance the breakdown of plant stems, leaves, and debris to further close the nutrient loop. Plasma carrier gases such as carbon dioxide (CO2), nitrogen (N2), and air were used to explore variations in recovery and potential chemical by-products. Plasma processed inedible biomass was added to varying concentrations of acid solution for leaching of nutrients (e.g. potassium (K) , magnesium (Mg), calcium (Ca), and phosphorus (P)) for reuse in the crop production cycle. We also examined total N2 recovery. Results are presented showing the impact of plasma processing prior to acid leaching on recovery of plant nutrients.

Kenneth Engeling↗
NASA NTRS1998

Modeling the Growth Rates of Tetragonal Lysozyme Crystal Faces

The measured macroscopic growth rates of the (110) and (101) faces of tetragonal lysozyme show an unexpectedly complex dependence on the supersaturation. The growth rates decay asymptotically to zero when the supersaturation is lowered to zero and increase rapidly when the supersaturation is increased. When supersaturations are increased still further the growth rates attain a maximum before starting to decrease. However, growth of these crystals is known to proceed by the classical dislocation and 2D nucleation growth mechanisms. This anomaly can be explained if growth is assumed to occur not by monomer units but by lysozyme aggregates. Analysis of the molecular packing of these crystals revealed that they were constructed of strongly bonded 4(sub 3) helices, while weaker bonds were responsible for binding the helices to each other. It follows that during crystal growth the stronger bonds are formed before the weaker ones. Thus, the growth of these crystals could be viewed as a two step process: aggregate growth units corresponding to the 4(sub 3) helix are first formed in the bulk solution by stronger intermolecular bonds and then attached to the crystal face by weaker bonds on dislocation hillocks or 2D islands. This will lead to a distribution of aggregates in the solution with monomers and lower order aggregates being predominant at low supersaturations and higher order aggregates being predominant at high supersaturations. If the crystal grows mostly by higher order aggregates, such as tetramers and octamers, it would explain the anomalous dependence of the growth rates on the supersaturation. Besides the analysis of molecular packing, a comprehensive analysis of the measured (110) and (101) growth rates was also undertaken in this study. The distribution of aggregates in lysozyme nutrient solutions at various solution conditions were determined from reversible aggregation reactions at equilibrium. The supersaturation was defined for each aggregate species with respect to its concentration at saturation in order to apply growth rate models to this process. The measured growth rates were then compared with the predicted ones from several dislocation and 2D nucleation growth models, employing tetramer and octamer growth units in polydisperse solutions and monomer units in monodisperse solutions. For the (110) face, the calculations consistently showed that the measured growth rates followed the expected model relations with octamer growth units. For the (101) face, it is not possible to obtain a clear agreement between the predicted and measured growth rates for a single growth unit as done for the (110) face. However, the calculations do indicate that the average size of the growth unit is between a tetramer and an octamer. This suggests that tetramers, octamers and other intermediate size growth units all participate in the growth process for this face. These calculations show that it is possible to model the macroscopic protein crystal growth rates if the molecular level processes can be account for, particularly protein aggregation processes in the bulk solution. Our recent investigations of tetragonal lysozyme crystals employing high resolution atomic force microscopy scans have further confirmed the growth of these crystals by aggregate growth units corresponding to 4(sub 3) helices.

Li, Meirong↗
NASA NTRS2011

ISS Operations Cost Reductions Through Automation of Real-Time Planning Tasks

In 2008 the Johnson Space Center s Mission Operations Directorate (MOD) management team challenged their organization to find ways to reduce the costs of International Space station (ISS) console operations in the Mission Control Center (MCC). Each MOD organization was asked to identify projects that would help them attain a goal of a 30% reduction in operating costs by 2012. The MOD Operations and Planning organization responded to this challenge by launching several software automation projects that would allow them to greatly improve ISS console operations and reduce staffing and operating costs. These projects to date have allowed the MOD Operations organization to remove one full time (7 x 24 x 365) ISS console position in 2010; with the plan of eliminating two full time ISS console support positions by 2012. This will account for an overall 10 EP reduction in staffing for the Operations and Planning organization. These automation projects focused on utilizing software to automate many administrative and often repetitive tasks involved with processing ISS planning and daily operations information. This information was exchanged between the ground flight control teams in Houston and around the globe, as well as with the ISS astronaut crew. These tasks ranged from managing mission plan changes from around the globe, to uploading and downloading information to and from the ISS crew, to even more complex tasks that required multiple decision points to process the data, track approvals and deliver it to the correct recipient across network and security boundaries. The software solutions leveraged several different technologies including customized web applications and implementation of industry standard web services architecture between several planning tools; as well as a engaging a previously research level technology (TRL 2-3) developed by Ames Research Center (ARC) that utilized an intelligent agent based system to manage and automate file traffic flow, archiving f data, and generating console logs. This technology called OCAMS (OCA (Orbital Communication System) Management System), is now considered TRL level 9 and is in daily use in the Mission Control Center in support of ISS operations. These solutions have not only allowed for improved efficiency on console; but since many of the previously manual data transfers are now automated, many of the human error prone steps have been removed, and the quality of the planning products has improved tremendously. This has also allowed our Planning Flight Controllers more time to focus on the abstract areas of the job, (like the complexities of planning a mission for 6 international crew members with a global planning team), instead of being burdened with the administrative tasks that took significant time each console shift to process. The resulting automation solutions have allowed the Operations and Planning organization to realize significant cost savings for the ISS program through 2020 and many of these solutions could be a viable

Hall, Timothy A.↗
NASA NTRS1995

Numerical solution of differential equations by artificial neural networks

Conventionally programmed digital computers can process numbers with great speed and precision, but do not easily recognize patterns or imprecise or contradictory data. Instead of being programmed in the conventional sense, artificial neural networks (ANN's) are capable of self-learning through exposure to repeated examples. However, the training of an ANN can be a time consuming and unpredictable process. A general method is being developed by the author to mate the adaptability of the ANN with the speed and precision of the digital computer. This method has been successful in building feedforward networks that can approximate functions and their partial derivatives from examples in a single iteration. The general method also allows the formation of feedforward networks that can approximate the solution to nonlinear ordinary and partial differential equations to desired accuracy without the need of examples. It is believed that continued research will produce artificial neural networks that can be used with confidence in practical scientific computing and engineering applications.

Meade, Andrew J., Jr.↗
NASA NTRS1998

An Image Retrieval and Processing Expert System for the World Wide Web

This paper presents a system that is being developed in the Laboratory of Applied Remote Sensing and Image Processing at the University of P.R. at Mayaguez. It describes the components that constitute its architecture. The main elements are: a Data Warehouse, an Image Processing Engine, and an Expert System. Together, they provide a complete solution to researchers from different fields that make use of images in their investigations. Also, since it is available to the World Wide Web, it provides remote access and processing of images.

Rodriguez, Ricardo↗
NASA NTRS1994

Upward appraisal as a means for improving supervisory performance and promoting process improvement, with long-term implications for organizational change

This study represents the implementation phase of an organizational development project which was initiated last year in the Management Support Division (MSD) at Langley Research Center to diagnose organizational functioning. As a result of MSD survey data from last year's effort, a Quality Action Team was created to address the responses compiled from the MSD Organizational Assessment Questionnaire and Follow-Up Questionnaire. The team was officially named the MSD Employee Relations Improvement Team (MERIT). MERIT's goal was to analyze major concerns generated by the questionnaires and to present feasible solutions to management which would improve supervisory performance, promote process improvement; and ultimately, lead to a better organization. The team met weekly and was very disciplined in following guidelines needed to ensure a fully functioning team. Several TQM tools were used during the team process, including brainstorming and the cause and effect diagram. One of the products produced by MERIT was a 'report card', more formally known as an upward appraisal system, to evaluate supervisory performance in the division office, its three branches, and in teams. Major areas of emphasis on the 47 item report card were those identified by employees through the previously administered questionnaires as needing to be improved; specifically, training, recognition, teamwork, supervision and leadership, and communication. MERIT created an enlarged and modified version of the report card which enabled scores for each individual supervisor to be recorded on a separate form, along with summary results and employee comments. Report card results have been compiled and fed back to the Division Chief and Assistant Division Chief. These individuals will in turn, feed the results back to the remaining supervisors and the team leaders. Although results differ among supervisors, some similarities exist. Communication generally appears to be adequate, which represents an improvement over last year. In contrast, recognition and teamwork are the two major areas where improvement in supervisory performance seems to be most needed. The initial report card results will serve as a baseline against which future performance ratings will be compared. Once supervisors have been presented with their data and given an opportunity to analyze and discus the results, they will be assisted in developing an action plan for improving their performance and work processes. They will be provided with ongoing support from management in following through with the action plan.

Siegfeldt, Denise V.↗
NASA NTRS1967

Dual photochemical replenisher system reduces chemical losses

Dual replenisher system reduces chemical losses and maintains optimum solution concentration during long nonprocessing cycles of photo processing machines. Using a single 3-position switch and solenoid control valves, the system provides instantaneous flow control to each processing tank.

Kolber, J. M.↗