Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sensor performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Safe2Ditch Steer-To-Clear Development and Flight Testing

This paper describes a series of small unmanned aerial system (sUAS) flights performed at NASA Langley Research Center in April and May of 2019 to test a newly added Steer-to-Clear feature for the Safe2Ditch (S2D) prototype system. S2D is an autonomous crash management system for sUAS. Its function is to detect the onset of an emergency for an autonomous vehicle, and to enable that vehicle in distress to execute safe landings to avoid injuring people on the ground or damaging property. Flight tests were conducted at the City Environment Range for Testing Autonomous Integrated Navigation (CERTAIN) range at NASA Langley. Prior testing of S2D focused on rerouting to an alternate ditch site when an occupant was detected in the primary ditch site. For Steer-to-Clear testing, S2D was limited to a single ditch site option to force engagement of the Steer-to-Clear mode. The implementation of Steer-to-Clear for the flight prototype used a simple method to divide the target ditch site into four quadrants. An RC car was driven in circles in one quadrant to simulate an occupant in that ditch site. A simple implementation of Steer-to- Clear was programmed to land in the opposite quadrant to maximize distance to the occupant’s quadrant. A successful mission was tallied when this occurred. Out of nineteen flights, thirteen resulted in successful missions. Data logs from the flight vehicle and the RC car indicated that unsuccessful missions were due to geolocation error between the actual location of the RC car and the derived location of it by the Vision Assisted Landing component of S2D on the flight vehicle. Video data indicated that while the Vision Assisted Landing component reliably identified the location of the ditch site occupant in the image frame, the conversion of the occupant’s location to earth coordinates was sometimes adversely impacted by errors in sensor data needed to perform the transformation. Logged sensor data was analyzed to attempt to identify the primary error sources and their impact on the geolocation accuracy. Three trends were observed in the data evaluation phase. In one trend, errors in geolocation were relatively large at the flight vehicle’s cruise altitude, but reduced as the vehicle descended. This was the expected behavior and was attributed to sensor errors of the inertial measurement unit (IMU). The second trend showed distinct sinusoidal error for the entire descent that did not always reduce with altitude. The third trend showed high scatter in the data, which did not correlate well with altitude. Possible sources of observed error and compensation techniques are discussed.

Petty, Bryan J.↗
NASA NTRS2023

Distributed Ground Sensor Fusion Based Object Tracking for Autonomous Advanced Air Mobility Operations

Autonomous operations are a crucial aspect in the context of Advanced Air Mobility and other emerging aviation markets. In order to enable this autonomy, an accurate and detailed understanding of the positions of the various vehicles in the air is necessary. Full localization independent of on-board sensors makes the system suitable for noncooperative vehicles. This paper focuses on the object tracking part that relies on distributed ground-based sensor fusion, considering specific properties and limitations of different sensor types. Results show satisfactory performance in nominal scenarios with full coverage. Dropouts of individual sensors affect the accuracy of the tracking results, which agrees with expectations for partial coverage, when full localization is not achievable anymore. Finally, a study is performed to identify which parameters have the largest impact on the fit error.

Autonomous↗
NASA NTRSDate not supplied

Applying Sensor Uncertainty Mitigation Schemes to Detect-and-Avoid Systems

Impact of sensor noise on the performance of Detect-And-Avoid (DAA) systems can be reduced by implementing various mitigation schemes. This paper evaluates the Sensor Uncertainty Mitigation (SUM) method, implemented in the Detect and Avoid Alerting Logic for Unmanned Systems (DAIDALUS) algorithm, a reference implementation in the DAA minimum operational performance standards. DAIDALUS SUM performance is evaluated using a few safety and operational suitability metrics and compared with more traditional approaches using static safety buffers. A large number of encounters representative of low-speed unmanned aircraft against non-cooperative manned aircraft are simulated and evaluated. An air-to-air radar model produces representative sensor noise for the DAA system. Results show that increasing the tunable parameters for horizontal and vertical uncertainty in DAIDALUS SUM improves the safety metric at the cost of increasing the number of system alerts leading to increased workload. A range of SUM parameters is recommended as suitable values for the type of operations considered for this work. General trends and optimal SUM configurations were found to be nearly the same for two large and very different encounter data sets.

detect and avoid↗
NASA NTRS2021

Evaluation of Sensor Uncertainty Mitigation Methods for Detect-and-Avoid Systems

The impact of sensor noise on the performance of Detect-And-Avoid (DAA) systems can be reduced by implementing various mitigation schemes. This paper evaluates two such methods. One of them is the Sensor Uncertainty Mitigation (SUM) method, implemented in the Detect and Avoid Alerting Logic for Unmanned Systems (DAIDALUS) algorithm, a reference implementation in the DAA minimum operational performance standards. The second method is the Virtual Intruder State Aggregation (VISA), which averages multiple subsequent intruder states extrapolated to the current (most recent) time into a single ``aggregated`` intruder state. The VISA method can be used either individually as a sensor noise mitigation method in its own right, or in combination with DAIDALUS SUM. The performance of these methods is evaluated using three safety and operational suitability metrics and compared with a baseline configuration using static safety buffers. A large number of encounters representative of low-speed unmanned aircraft against non-cooperative manned aircraft, not equipped with a broadcasting transponder or ADS-B out system, are simulated and evaluated. An air-to-air radar model produces representative sensor noise for the DAA system. Results show that increasing the DAIDALUS SUM parameters for horizontal and vertical uncertainty improves the safety metric at the cost of increasing the number of actionable alerts leading to increased workload. A range of SUM parameters is recommended as suitable values for the type of operations considered for this work. VISA was found to be almost as effective as other noise mitigation methods even when it was used alone. Combining VISA with DAIDALUS SUM achieved the best performance among all investigated methods used with DAIDALUS. General trends and optimal SUM configurations were found to be nearly the same for two large and very different encounter data sets.

Detect-and-Avoid Systems↗
NASA NTRS2023

Performance of High-Resolution Mo/Cu Transition Edge Sensors Fabricated Using a Lift-Off Process

The soft X-ray band below ≈0.5 keV is expected to provide rich information on metallicity, temperature, and distribution of hot gas in our galaxy and the intergalactic medium. Resolving these densely spaced emission lines requires energy resolution on the order of 1--2 eV. The low count rates from diffuse astrophysical sources also necessitate large collection areas, particularly for a sounding rocket instrument with short exposure times and limited resources. This translates to large pixel sizes (about 1 mm 2 ) for a reasonable number of read-out channels. To achieve the required energy resolution with 200 nm thin Au absorbers (heat capacity C about 1 pJ/K), we are developing TES microcalorimeters with very high temperature sensitivity (αI), low enough current sensitivity (βI), and minimal excess noise (M). Out of the various fabrication approaches for the TES bilayer we have explored, the lift-off approach (as pioneered for Mo/Au TES by Joel Weber at NIST) so far is the simplest to execute. The simple square TES geometries we have tested to date show promising results for αI and βI. Measured complex impedance and noise for bare devices without absorbers are well described by two-body thermal models and their excess noise is found to be consistent with predictions for mixed-down Johnson noise by Wessels et al. More sensitive measurements with larger heat capacity are planned to accurately determine excess noise. In this paper, we give an overview of the process and summarize results of our detailed characterization measurements for thermal conductance G, αI, βI, and noise for several devices across a range of bias points.

Felix T Jaeckel↗
NASA NTRS1993

Active stabilization to prevent surge in centrifugal compression systems

This report documents an experimental and analytical study of the active stabilization of surge in a centrifugal engine. The aims of the research were to extend the operating range of a compressor as far as possible and to establish the theoretical framework for the active stabilization of surge from both an aerodynamic stability and a control theoretic perspective. In particular, much attention was paid to understanding the physical limitations of active stabilization and how they are influenced by control system design parameters. Previously developed linear models of actively stabilized compressors were extended to include such nonlinear phenomena as bounded actuation, bandwidth limits, and robustness criteria. This model was then used to systematically quantify the influence of sensor-actuator selection on system performance. Five different actuation schemes were considered along with four different sensors. Sensor-actuator choice was shown to have a profound effect on the performance of the stabilized compressor. The optimum choice was not unique, but rather shown to be a strong function of some of the non-dimensional parameters which characterize the compression system dynamics. Specifically, the utility of the concepts were shown to depend on the system compliance to inertia ratio ('B' parameter) and the local slope of the compressor speedline. In general, the most effective arrangements are ones in which the actuator is most closely coupled to the compressor, such as a close-coupled bleed valve inlet jet, rather than elsewhere in the flow train, such as a fuel flow modulator. The analytical model was used to explore the influence of control system bandwidth on control effectiveness. The relevant reference frequency was shown to be the compression system's Helmholtz frequency rather than the surge frequency. The analysis shows that control bandwidths of three to ten times the Helmholtz frequency are required for larger increases in the compressor flow range. This has important implications for implementation in gas turbine engines since the Helmholtz frequencies can be over 100 Hz, making actuator design extremely challenging.

Epstein, Alan H.↗
DOE OSTI2023

Development Plan for Acoustic Emission and Vibration Sensors

This document discusses the need for high temperature, radiation tolerant sensors for monitoring vibration and acoustic emissions in advanced reactors and irradiation experiments. Testing of several commercial sensors using infrastructure available at Idaho National Laboratory was performed to benchmark currently available sensors as well as the test facilities. Finally, a strategy for developing sensors for more extreme environments is presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1973

Remote sensors - Prospects and limitations

Review of the history, present status, and future prospects and limitations of remote sensing systems for satellite-based earth resources surveys. The objectives and special areas of interest of ongoing sensor development experiments are summarized, and the measurement and performance goals of current potential sensor research is discussed.

Lehmann, J.↗
NASA NTRS1997

Registration of video sequences from multiple sensors

In this paper, we describe an approach for registration of video sequences from a suite of multiple sensors including television, infrared and radar. Video sequences generated by these sensors may contain abrupt changes in local contrast and inconsistent image features, which pose additional difficulties for registration. Our approach to registration addresses the difficulties caused by using multiple sensors. We use a representation for registration that is invariant to local contrast changes, followed by smoothing of the resulting error measure used for registration, for robust estimation of registration parameters. We use an iterative procedure to reduce the effect of inconsistent features. Finally, we describe a method that uses same-sensor registration to aide in performing registration of sequences of video frames across multiple sensors.

Sharma, Ravi K.↗
NASA NTRSDate not supplied

Development and Field Test Results of Distributed Ground Sensor Fusion Based Object Tracking

Autonomous operations are a crucial aspect in the context of Advanced Air Mobility and other emerging aviation markets. In order to enable this autonomy, an accurate and detailed understanding of the positions of the various vehicles in the air is necessary. Full localization independent of on-board sensors makes the system suitable for noncooperative vehicles. This paper focuses on the object tracking part that relies on distributed ground-based RF and other sensor fusion, considering specific properties and limitations of different sensor types. Results show satisfactory performance in nominal scenarios with full coverage for some sensor types, but RF signals are challenging because of their nature. This paper includes the results from simulations as well as field tests to support the observations and conclusions.

sensor fusion↗
NASA NTRSDate not supplied

Using Open Innovation in Reducing Risk to Crews

In the exploration of destinations outside of Earth's neighborhood, specifically Mars, scientific and engineering inquiries have occurred by two means; observations from satellites and observations by landed spacecraft. Satellite observations (Mariner, MRO, Mars Odyssey, provide global-scale spatial and temporal data while landed spacecraft (Viking, Mars Pathfinder, Spirit, Opportunity, Phoenix Mars Lander) investigate highly localized areas of the surface of the planet. In preparation for human exploration, extensive knowledge of the surface and atmospheric environments should be known before the first human leaves Earth. The primary goal of performing reconnaissance on Mars on a sub-global scale is to know as much as possible about the environment to which crews will be subjected. At the current rate of launching and landing probes to Mars, it will take a very long time to understand the surface and atmospheric conditions associated with the regions where prospective crews may land. Meanwhile electronics and electrical systems are rapidly getting smaller. One can argue that to acquire the knowledge of the region, one must take hundreds, maybe thousands of measurements simultaneously. One means to perform such a task is to deploy a swarm of sensors. Such a swarm would perform an in-situ assessment of the region. Imagine a close flyby mission to Mars for example, where mini- to micro-sensors are deposited into the atmosphere over half an orbit or more. The sensors, captured by the atmospheric drag and Martian gravity slowly descend buffeted about by Martian winds and weather until they settle on the surface a great time later (think of how long dust takes to settle). As they descend they communicate a vast array of data; temperature, chemistry, pressure, radiation dose, electric or magnetic properties from a region of the planet and an individual sensor need not measure the same quantity as its neighbors. Initially, they could move at the whim of the environment but later versions could have locomotion or propulsion mechanisms. Humans wouldn't need to decide where the sensors go, the sensors do that for themselves. This is a key strength of a sensor swarm. The intelligence relies on the group not on a decision maker on earth. Real time sensor inputs direct what the swarm considers most interesting to investigate resulting in emergent behavior. We issued a $20,000 challenge to the global innovators to provide solutions as to how such a swarm could be initialized and by what protocols and methodologies by which they operate. Over 400 innovators from 49 countries took a look at the problem, with three receiving partial awards for solutions.

Mel Ferebee↗
NASA NTRS1993

The results of the in-flight attitude sensor calibration for the Arthur Holly Compton Gamma Ray Observatory

The Arthur Holly Compton Gamma Ray Observatory (GRO) was launched by the shuttle Atlantis in April 1991. This paper presents the results of the attitude sensor calibration that was performed during the early mission. The GSFC Flight Dynamics Facility (FDF) performed an alignment calibration of the two fixed-head star trackers (FHST's) and two fine Sun sensors (FSS's) on board Compton GRO. The results show a 27-arcsecond shift between the bore sights of the FHST's with respect to prelaunch measurements. The alignments of the two FSS's shifted by 0.20 and 0.05 degree. During the same time period, the Compton GRO science teams performed an alignment calibration of the science instruments with respect to the attitude reported by the on board computer (OBC). In order to preserve these science alignments, FDF adjusted the overall alignments of the FHST's and FSS's, obtained by the FDF calibration, such that when up linked to the OBC, the shift in the OBC-determined attitude is minimized. FDF also calibrated the inertial reference unit (IRU), which consists of three dual-axis gyroscopes. The observed gyro bias matched the bias that was solved for by the OBC. This bias drifted during the first 6 days after release. The results of the FDF calibration of scale factor and alignment shifts showed changes that were of the same order as their uncertainties.

Davis, W. S.↗
NASA NTRS1978

A portable hypergolic oxidizer vapor sensor for NASA's Space Shuttle program

The design and performance characteristics of an electrochemical NO2 sensor selected by NASA for the space shuttle program is described. The instrument consists of a sample pump, an electrochemical cell, and control and display electronics. The pump pushes the sample through the electrochemical cell where the vapors are analyzed and an output proportional to the NO2 concentration is produced. The output is displayed on a panel meter, and is also available at a recorder jack. The electrochemical cell is made up of a polypropylene chamber covered with teflon membrane faceplates. Plantinum electrodes are bonded to the faceplates, and the sensing and counter electrodes are potentiostatically controlled at -200 mV with respect to the reference electrode. The cell is filled with electrolyte, consisting of 13.5 cc of 23% solution of KOH.

Helms, W. R.↗
NASA NTRS1983

Three-way partitioning of sea surface temperature measurement error

Given any set of three 2 degree binned anomaly sea surface temperature (SST) data sets by three different sensors, estimates of the mean square error of each sensor estimate is made. The above formalism performed on every possible triplet of sensors. A separate table of error estimates is then constructed for each sensor.

Chelton, D.↗
NASA NTRS1989

Data-Processing System For Test Airplane

Real-time display of data on performance supports decisions regarding maneuvers. Data from sensors aboard airplane transmitted to control station on ground for immediate processing and display. Data-acquisition subsystem aboard airplane uses both pulse code modulation and frequency modulation for transmission of sensor data on operation of engine, performance of airplane, and conditions in atmosphere. No data recorded on aircraft.

Ray, R. J.↗