Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scaled testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Large-Scale Wind-Tunnel Tests of Exhaust Ingestion Due to Thrust Reversal on a Four-Engine Jet Transport during Ground Roll

Wind-tunnel tests have been conducted on a large-scale model of a swept-wing jet transport type airplane to study the factors affecting exhaust gas ingestion into the engine inlets when thrust reversal is used during ground roll. The model was equipped with four small jet engines mounted in nacelles beneath the wing. The tests included studies of both cascade and target type reversers. The data obtained included the free-stream velocity at the occurrence of exhaust gas ingestion in the outboard engine and the increment of drag due to thrust reversal for various modifications of thrust reverser configuration. Motion picture films of smoke flow studies were also obtained to supplement the data. The results show that the free-stream velocity at which ingestion occurred in the outboard engines could be reduced considerably, by simple modifications to the reversers, without reducing the effective drag due to reversed thrust.

Tolhurst, William H., Jr.↗
NASA NTRS1974

Propulsion system tests on a full scale Centaur vehicle to investigate 3-burn mission capability of the D-lT configuration

Propulsion system tests were conducted on a full scale Centaur vehicle to investigate system capability of the proposed D-lT configuration for a three-burn mission. This particular mission profile requires that the engines be capable of restarting and firing for a final maneuver after a 5-1/2-hour coast to synchronous orbit. The thermal conditioning requirements of the engine and propellant feed system components for engine start under these conditions were investigated. Performance data were also obtained on the D-lT type computer controlled propellant tank pressurization system. The test results demonstrated that the RL-10 engines on the Centaur vehicle could be started and run reliably after being thermally conditioned to predicted engine start conditions for a one, two and three burn mission. Investigation of the thermal margins also indicated that engine starts could be accomplished at the maximum predicted component temperature conditions with prestart durations less than planned for flight.

Groesbeck, W. A.↗
NASA NTRS1991

Evaluation of some scale effects in the response and failure of composite beams

The feasibility of using scale model testing for predicting full-scale behavior of composite beams loaded in tension and flexure was investigated. Classical laws of similitude were applied to fabricate and test replica model beams to identify scaling effects in the load response, strength, and mode of failure. Experiments were conducted using graphite-epoxy composite beams having different laminate stacking sequences and a range of scaled sizes. Results indicated that the elastic response of scaled composite beams was independent of specimen size. However, a significant scale effect in strength was observed. In addition, a transition in failure mode was observed among scaled beams of certain laminate stacking sequences. Weibull statistical and fracture mechanics based models were applied to predict the strength scale effect since standard failure criteria cannot account for the influence of absolute specimen size in failure.

Jackson, Karen E.↗
NASA NTRS1945

High-Speed Wind-Tunnel Tests of a 0.3-Scale Model of the P-47D Airplane

Presented in this report are the results of high-speed wind-tunnel tests of a 0.3-scale model of the P-47D airplane. Included are the aerodynamic characteristics of the model, pressure distributions on the wing and horizontal tail, elevator hinge moments, and tuft photographs showing the flow over the wing and horizontal tail. The results indicate that, at level-flight lift coefficients, the P-47D airplane will not exhibit a diving tendency below a Mach number of 0.78 at an altitude of 20,000 feet or below a Mach number of 0.72 at an altitude of 40,000 feet. The Mach number at which the lift, drag, and pitching-moment coefficients diverged rapidly from the low speed values is about C.15 higher than the critical Mach number. This is an unusually large margin.

William T Hamilton↗
NASA NTRS2005

NARC Rayon Replacement Program for the RSRM Nozzle, Phase IV Qualification and Implementation Status

The Space Shuttle NARC Rayon Replacement Program has down-selected Enka rayon as a replacement for the obsolete NARC rayon in the nozzle carbon cloth phenolic (CCP) ablative insulators. Full qualification testing of the Enka rayon-based carbon cloth phenolic is underway, including processing, thmal/structural properties, and hot-fire subscale tests. Required thermal-structural capabilities, together with confidence in erosio/char performance in simulated and subscale hot fire tests such as Wright-Patterson Air Force Base Laser Hardened Materials Evaluation Laboratory testing, NASA-MSFC 24-inch motor tests, NASA-MSFC Solid Fuel Torch - Super Sonic Blast Tube, NASA-MSFC Plasma Torch Test Bed, ATK Thiokol Forty Pound Charge and NASA-MSFC MNASA justified the testing of the new Enka-rayon candidate on full-scale static test motors. The first RSRM full-scale static test motor nozzle, fabricated using the new Enka rayon-based CCP, was successfully demonstrated in June 2004. Two additional static test motors are planned with the new Enka rayon in the next two years along with additional A-basis property characterization. Process variation or "corner-of-the-box" testing together with cured and uncured aging studies are also planned as some of the pre-flight implementation activities with 5-year cured aging studies over-lapping flight hardware fabrication.

Haddock, M. Reed↗
NASA NTRS1974

Heat transfer tests of an 0.006-scale thin skin space shuttle thermocouple model (41-0) in the Langley Research Center variable density tunnel at M equals 8 (OH13)

Orbiter entry heating distributions were obtained, and phase change paint data was correlated with thermocouple data during a program of heat transfer testing on a 0.006 scale space shuttle orbiter vehicle. The orbiter was tested at 0, 30, and 35 degrees angle of attack at Reynolds numbers of 1, 2, 3, 4, and 6 million per foot. Temperature data were obtained from a total of 57 thermocouples.

Walstad, D. G.↗
NASA NTRS1972

A proposed USAF fatigue evaluation program based upon recent systems experience

The United States Air Force has published a document entitled Aircraft Structural Integrity Program. One phase of the program is concerned with the fatigue life certification of all types of military aircraft. The document describes the criteria, analyses, and tests that are necessary in order to satisfy the USAF fatigue life requirement. Some recent and valid criticism has been directed toward the document, particularly the fatigue-life requirements contained in it. Some changes are proposed based on surveys conducted in the United States and abroad as well as some recent systems' experience. The surveys covered both military and civilian organizations. The fatigue certification case histories of selected military and commercial aircraft are presented. The design development element tests, preproduction design verification tests, and full-scale fatigue tests of each are described. A brief status report on the revisions to the MIL-A-008860 series specifications is included.

Haviland, G. P.↗
NASA NTRS1972

In-flight aeroacoustic environments on prospective space shuttle vehicles

The problem of in-flight aerodynamic noise has been studied by reliable estimates of full scale surface-pressure fluctuations from scale model tests in wind tunnels. Scaling relationships have been verified, and many details of the fluctuating pressure characteristics such as spatial correlation and convection velocities are understood. The effects of the wind tunnel environmental turbulence and noise have also been investigated sufficiently so that threshold levels of usable data are known.

Dods, J. B., Jr.↗
NASA NTRS1972

Analyses and tests confirm design of proprotor aircraft.

Discussion of the design features of a 300-knot tilt-proprotor VTOL aircraft having proprotors 25 ft in diameter, an empty weight of 7390 pounds, a maximum VTOL gross weight of 12,400 pounds, and a design dive speed of 300 knots. Proprotor stability analysis covering aeroelastic stability characteristics and flight mode stability characteristics is included. An evaluation of the proprotor design is made on the basis of aerodynamic and aeroelastic model tests and full-scale performance tests. The test results and other obtained research data suggest the readiness of this aircraft design for construction and flight tests.

Edenborough, H. K.↗
NASA NTRS1975

Development and flight tests of vortex-attenuating splines

The ground tests and full-scale flight tests conducted during development of the vortex-attenuating spline are described. The flight tests were conducted using a vortex generating aircraft with and without splines; a second aircraft was used to probe the vortices generated in both cases. The results showed that splines significantly reduced the vortex effects, but resulted in some noise and climb performance penalties on the generating aircraft.

Hastings, E. C., Jr.↗
NASA NTRS1976

Comparison of vortex lattice predicted forces with wind tunnel experiments for the F-4E(CCV) airplane with a closely coupled canard

The F-4E (CCV) wind tunnel model with closely coupled canard control surfaces was analyzed by means of a version of a vortex lattice program that included the effects of nonlinear leading edge or side edge vortex lift on as many as four individual planforms. The results were compared with experimental data from wind tunnel tests of a 5% scale model tested at a Mach number M = 0.6. They indicated that a nonlinear vortex lift developed on the side edges due to tip vortices, but did not appear to develop on the leading edges within the range of angles of attack that were studied. Instead, substantial leading edge thrust was developed on the lifting surfaces. A configuration buildup illustrated the mutual interference between the wing and control surfaces. On the configuration studied, addition of the wing increased the loading on the canard, but the additional load on the canard due to adding the stabilator was small.

Gross, L. W.↗
NASA NTRS1976

Ground test of the D shaped vented thrust vectoring nozzle

Static ground tests of a large scale lift/cruise thrust vectoring nozzle were conducted to establish: (1) vectoring performance 'in' and 'out' of ground effect; (2) thrust spoilage capability; (3) compatibility of the nozzle with a turbotip fan; and (4) the nozzle structural temperature distribution. Vectoring performance of a short coupled, vented nozzle design on a large scale, (60%) basis was compared with small scale (4.5%) test nozzle results. The test nozzle was a "boilerplate" model of the MCAIR "D" vented nozzle configured for operation with the LF336/J85 turbotip lift fan system. Calibration of the LF336/J85 test fan with a simple convergent nozzle was performed with four different nozzle exit areas to establish reference thrust, nozzle pressure ratio, and nozzle corrected flow characteristics for comparison with the thrust vectoring nozzle data. Thrust vectoring tests with the 'D' vented nozzle were conducted over the range of vector angles between 0 and 117 deg for several different nozzle exit areas.

Esker, D. W.↗
NASA NTRS1977

Pollution reduction technology program for small jet aircraft engines: Class T1

Small jet aircraft engines (EPA class T1, turbojet and turbofan engines of less than 35.6 kN thrust) were evaluated with the objective of attaining emissions reduction consistent with performance constraints. Configurations employing the technological advances were screened and developed through full scale rig testing. The most promising approaches in full-scale engine testing were evaluated.

Bruce, T. W.↗
NASA NTRS1978

Quiet, Clean, Short-Haul, Experimental Engine (QCSEE) Under-The-Wing (UTW) engine acoustic design

The acoustic considerations involved in the low source noise basic engine design and the design procedures followed in the development of the under-the-wing (UTW) engine boilerplate and composite nacelle acoustic treatment designs are presented. Laboratory experiments, component tests, and scale model and engine tests supporting the UTW engine acoustic design are referenced. Acoustic design features include a near-sonic inlet, low fan and core pressure ratios, low fan tip speed, high and low frequency stacked core treatment, multiple thickness treatment, and fan frame and stator vane treatment.

Sowers, H. D.↗
NASA NTRS1978

Quiet, Clean, Short-Haul Experimental Engine (QCSEE) Over-The-Wing (OTW) engine acoustic design

The acoustic considerations involved in the low source noise basic engine design and the design procedures followed in the development of the over-the-wing (OTW) nacelle acoustic treatment design are presented. Laboratory experiments, component tests, and scale model and engine tests supporting the OTW engine acoustic design are referenced. Acoustic design features include a near-sonic inlet, low fan and core pressure ratios, low fan tip speed, high and low frequency stacked core treatment, multiple thickness treatment, and fan frame and stator vane treatment.

Sowers, H. D.↗
NASA NTRS1980

Large space structures activity at MSFC

This paper describes a broad based set of activities which have been undertaken at the Marshall Space Flight Center (MSFC) developing technologies necessary to emplace and operate large structures in space. Progress has been made in the development of processes and equipment needed for the in space fabrication of structural members in both aluminum and graphite composite materials. Designs for member joining attachments have been completed and the evaluation of procedures for structural assembly have been simulated and evaluated utilizing the MSFC Neutral Buoyancy Facility. A concept of a flight test necessary for flight verification of the technologies for space fabrication, assembly, and operation of large space structure is described. Recently initiated is a project to develop design characteristics of a deployable structure required for the Science and Applications Space Platform (SASP). This is being accomplished through the design, fabrication, analysis, and test of a full scale ground test article which reflects the influence of system requirements of the SASP. Development of designs for erectable/deployable structures which are modular and have various applications to large space structures is in progress.

Denton, S. J.↗
NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗