Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “raw materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Temperature transformation of blended magnesium potassium phosphate cement binders

In this study, a multi-technique approach was utilised to determine the high temperature performance of magnesium potassium phosphate cement (MKPC) blended with fly ash (FA) or ground granulated blast furnace slag (GBFS) with respect to nuclear waste immobilisation applications. Conceptual fire conditions were employed (up to 1200 °C, 30 min) to simulate scenarios that could occur during interim storage, transportation or within a final geological disposal facility. After exposure up to 400 °C, the main crystalline phase, struvite-K (MgKPO{sub 4}·6H{sub 2}O), was dehydrated to poorly crystalline MgKPO{sub 4} (with corresponding volumetric and mass changes), with MgKPO{sub 4} recrystallisation achieved by 800 °C. XRD and SEM/EDX analysis revealed reaction occurred between the MgKPO{sub 4} and FA/GBFS components after exposure to 1000–1200 °C, with the formation of potassium aluminosilicate phases, leucite and kalsilite (KAlSi{sub 2}O{sub 6} and KAlSiO{sub 4}), commensurate with a reduced relative intensity (or complete elimination) of the dehydrated struvite-K phase, MgKPO{sub 4.} This was further supported by solid-state NMR ({sup 27}Al and {sup 29}Si MAS), where only residual features associated with the raw FA/GBFS components were observable at 1200 °C. The high temperature phase transformation of blended MKPC binders resulted in the development of a glass/ceramic matrix with all existing porosity infilled via sintering and the formation of a vitreous phase, whilst the physical integrity was retained (no cracking or spalling). This study demonstrates that, based on small-scaled specimens, blended MKPC binders should perform satisfactorily under fire performance parameters relevant to the operation of a geological disposal facility, up to at least 1200 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High strain rate nanoindentation testing: Recent advancements, challenges and opportunities

Recent advancements in electronics have renewed the interest in high strain rate nanoindentation testing, resulting in the development of new high strain rate nanoindentation test equipment and test methodologies. Here, in this work, the current state-of-the-art in high strain rate nanoindentation testing is critically reviewed, with focus on three key aspects - the testing equipment's dynamic mechanical and electronic response, test methodology, and post-processing of raw data to obtain hardness and strain rate. The challenges in instrument hardware design and post-test data analysis are discussed, along with optimal strain rate window for accurate high strain rate measurements. Specific focus will be on instrumented high strain rate testing using self-similar indenters at strain rates in excess of 100 s -1 , wherein load and depth of penetration into the sample are both measured or applied.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Empowering Scientific Discovery Through Computing at the Advanced Photon Source

This paper explores the challenges and solutions for managing and processing the vast amount of data generated by the Advanced Photon Source (APS), a synchrotron light source facility producing ultra-bright x-rays for diverse scientific domains. With 68 experimental beamlines covering materials research, biology, and more, the APS serves a wide user base across academia, government, and industry. The ongoing upgrade of the APS storage ring and installation of new instruments will amplify data generation and processing demands. This paper discusses the approach to address these demands through automated data processing using standardized workflows that produce faster scientific insights. The APS Data Management System coordinates various data related tasks to manage storage, data transfer, metadata cataloging, data processing, and interfaces with tools provided by Globus. Through integration with the Argonne Leadership Computing Facility (ALCF), APS users can efficiently access high-performance computing resources. Standardized workflows have led to reduced computational burdens on scientists and greater accessibility of high performance computing resources. We demonstrate how standardization and collaboration enable scientists to rapidly convert raw data into meaningful scientific results, establishing a streamlined path from data collection to analysis and ultimately to publication.

Parraga, Hannah↗
NASA NTRS2010

Kepler Data Release 3 Notes

This describes the collection of data and the processing done on it so when researchers around the world get the Kepler data sets (which are a set of pixels from the telescope of a particular target (star, galaxy or whatever) over a 3 month period) they can adjust their algorithms fro things that were done (like subtracting all of one particular wavelength for example). This is used to calibrate their own algorithms so that they know what it is they are starting with. It is posted so that whoever is accessing the publicly available data (not all of it is made public) can understand it .. (most of the Kepler data is under restriction for 1 - 4 years and is not available, but the handbook is for everyone (public and restricted) The Data Analysis Working Group have released long and short cadence materials, including FFls and Dropped Targets for the Public. The Kepler Science Office considers Data Release 3 to provide "browse quality" data. These notes have been prepared to give Kepler users of the Multimission Archive at STScl (MAST) a summary of how the data were collected and prepared, and how well the data processing pipeline is functioning on flight data. They will be updated for each release of data to the public archive and placed on MAST along with other Kepler documentation, at http:// archive.stsci.edu/kepler/documents.html .Data release 3 is meant to give users the opportunity to examine the data for possibly interesting science and to involve the users in improving the pipeline for future data releases. To perform the latter service, users are encouraged to notice and document artifacts, either in the raw or processed data, and report them to the Science Office.

Cleve, Jeffrey E.↗
NASA NTRS2010

Kepler Data Release 4 Notes

The Data Analysis Working Group have released long and short cadence materials, including FFIs and Dropped Targets for the Public. The Kepler Science Office considers Data Release 4 to provide "browse quality" data. These notes have been prepared to give Kepler users of the Multimission Archive at STScl (MAST) a summary of how the data were collected and prepared, and how well the data processing pipeline is functioning on flight data. They will be updated for each release of data to the public archive and placed on MAST along with other Kepler documentation, at http://archive.stsci.edu/kepler/documents.html. Data release 3 is meant to give users the opportunity to examine the data for possibly interesting science and to involve the users in improving the pipeline for future data releases. To perform the latter service, users are encouraged to notice and document artifacts, either in the raw or processed data, and report them to the Science Office.

Van Cleve, Jeffrey↗
NASA NTRS2000

Surface Change Detection Using Large Footprint Laser Altimetry

Laser altimeters provide a precise and accurate method for mapping topography at fine horizontal and vertical scales. A laser altimeter provides range by measuring the roundtrip flight time of a short pulse of laser light from the laser altimeter instrument to the target surface. The range is then combined with laser beam pointing knowledge and absolute position knowledge to provide an absolute measurement of the surface topography. Newer generations of laser altimeters measure the range by recording the shape and time of the outgoing and received laser pulses. The shape of the return pulse can also provide unique information about the vertical structure of material such as vegetation within each laser footprint. Distortion of the return pulse is caused by the time-distributed reflections adding together and representing the vertical distribution of surfaces within the footprint. Larger footprints (10 - 100m in diameter) can support numerous target surfaces and thus provide the potential for producing complex return pulses. Interpreting the return pulse from laser altimeters has evolved from simple timing between thresholds, range-walk corrections, constant-fraction discriminators, and multi-stop time interval units to actual recording of the time varying return pulse intensity - the return waveform. Interpreting the waveform can be as simple as digitally thresholding the return pulse, calculating a centroid, to fitting one or more gaussian pulse-shapes to the signal. What we present here is a new technique for using the raw recorded return pulse as a raw observation to detect centimeter-level vertical topographic change using large footprint airborne and spaceborne laser altimetry. We use the correlation of waveforms from coincident footprints as an indication of the similarity in structure of the waveforms from epoch to epoch, and assume that low correlation is an indicator of vertical structure or elevation change. Thus, using vertically and horizontally geolocated waveforms as raw observables (i.e., waveforms tied to a common reference ellipsoid), we assess whether epoch-to-epoch vertical ground motion results in a decrease in the correlation of coincident waveforms over time, and whether this can be used to quantify the magnitude of the deformation. Results of computer models and an example over an area of eroded beachfront will be presented.

Blair, J. Bryan↗
DOE OSTI2024

Quantitative assessment of selenium diffusion and passivation in CdSeTe solar cells probed by spatially resolved cathodoluminescence

The introduction of selenium in CdSeTe/CdTe solar cells has led to improved device performances attributed to the passivation of bulk defects. In this work, high-resolution cathodoluminescence experiments are performed on a series of CdSeTe/CdTe thin films with different Se concentrations to quantify the mechanisms and the passivation role of Se. We demonstrate a universal dependence between the Se concentration and the radiative efficiency and a ten-fold enhancement of the luminescence between CdTe and CdSe 0.4 Te 0.6 . Raw luminescence maps are converted into maps of the Se concentration, revealing its graded profile within the stack. We demonstrate the diffusion of Se along CdTe grain boundaries induced by the cadmium chloride annealing treatment and determine the diffusion coefficients, which are more than eight times higher at grain boundaries than in grain interiors. These results provide microscopic insights into the distribution of Se and its impact on the passivation of CdSeTe/CdTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2024

Carbon-13 NMR spectra of lignin isolated from field grown transgenic poplar

Here we present a curated dataset of a series of 13C nuclear magnetic resonance (NMR) spectra of lignin isolated from transgenic monolignol 4-O-methyltransferase (MOMT4) engineered poplar. The transgenic poplar was collected from a 3-year field trial experiment. The poplar was Soxhlet-extracted with toluene/ethanol and the extractives-free poplar was then ball-milled in a Retsch PM100 planetary ball mill using a porcelain jar with ceramic balls at 600 rpm for 2 h. The ball-milled materials were then subjected to enzymatic hydrolysis for 48 h followed by centrifugation and washing with deionized water. The solid residue was extracted twice with 96:4 (v/v) 1,4-dioxane/water mixture at room temperature overnight. The extracts were combined, rotary evaporated, and freeze-dried to recover the lignin. The dry lignin samples were dissolved in deuterated dimethyl sulfoxide for NMR characterization. 13C experiments were performed in a Bruker Avance III HD 500 MHz NMR spectrometer operating at a frequency of 125.12 MHz for the 13C nucleus using a standard Bruker pulse sequence (zgpg) on a Prodigy platform cryoprobe. The NMR spectra were acquired under the following conditions: spectra width 229 ppm, 64k data points, 1s pulse delay, and 6k scans. All the data was processed using the Bruker’s TopSpin 3.6 software. Additional meta data is embedded in the raw spectra files.

13C NMR, lignin, poplar, field trial, MOMT4, CBI↗
DOE OSTI2024

Proton NMR spectra of lignin isolated from field grown transgenic poplar

Here we present a curated dataset of a series of 1H nuclear magnetic resonance (NMR) spectra of lignin isolated from transgenic monolignol 4-O-methyltransferase (MOMT4) engineered poplar. The transgenic poplar was collected from a 2-year-old rotation trees within a three-year field trial experiment. Two replicates were collected for each transgenic poplar for the 1H NMR analysis. The poplar samples were Soxhlet-extracted with toluene/ethanol to remove the extractives and the extractives-free poplar was then ball-milled in a Retsch PM100 planetary ball mill using a porcelain jar with ceramic balls at 600 rpm for 2 h. The ball-milled materials were subjected to enzymatic hydrolysis for 48 h followed by centrifugation and washing with deionized water. The solid residue was extracted twice with 96:4 (v/v) 1,4-dioxane/water mixture at room temperature overnight. The extracts were combined, rotary evaporated, and freeze-dried to recover lignin. The dry lignin samples were dissolved in deuterated dimethyl sulfoxide and transferred into a 5 mm NMR tube. 1H NMR experiments were performed in a Bruker Avance III HD 500 MHz NMR spectrometer operating at a frequency of 125.12 MHz for the 13C nucleus using a standard Bruker pulse sequence (zg) on a Prodigy platform cryoprobe. The NMR spectra were acquired with 16 ppm spectra width, 32k data points, 3s pulse delay, and 16 scans. All the data was processed using the Bruker’s TopSpin 3.6 software. Additional meta data is embedded in the raw spectra files.

1H NMR, lignin, poplar, field trial, MOMT4, CBI↗
NASA NTRS2012

Absolute Position of Targets Measured Through a Chamber Window Using Lidar Metrology Systems

Lidar is a useful tool for taking metrology measurements without the need for physical contact with the parts under test. Lidar instruments are aimed at a target using azimuth and elevation stages, then focus a beam of coherent, frequency modulated laser energy onto the target, such as the surface of a mechanical structure. Energy from the reflected beam is mixed with an optical reference signal that travels in a fiber path internal to the instrument, and the range to the target is calculated based on the difference in the frequency of the returned and reference signals. In cases when the parts are in extreme environments, additional steps need to be taken to separate the operator and lidar from that environment. A model has been developed that accurately reduces the lidar data to an absolute position and accounts for the three media in the testbed air, fused silica, and vacuum but the approach can be adapted for any environment or material. The accuracy of laser metrology measurements depends upon knowing the parameters of the media through which the measurement beam travels. Under normal conditions, this means knowledge of the temperature, pressure, and humidity of the air in the measurement volume. In the past, chamber windows have been used to separate the measuring device from the extreme environment within the chamber and still permit optical measurement, but, so far, only relative changes have been diagnosed. The ability to make accurate measurements through a window presents a challenge as there are a number of factors to consider. In the case of the lidar, the window will increase the time-of-flight of the laser beam causing a ranging error, and refract the direction of the beam causing angular positioning errors. In addition, differences in pressure, temperature, and humidity on each side of the window will cause slight atmospheric index changes and induce deformation and a refractive index gradient within the window. Also, since the window is a dispersive media, the effect of both phase and group indices have to be considered. Taking all these factors into account, a method was developed to measure targets through multiple regions of different materials and produce results that are absolute measurements of target position in three-dimensional space, rather than simply relative position. The environment in which the lidar measurements are taken must be broken down into separate regions of interest and each region solved for separately. In this case, there were three regions of interest: air, fused silica, and vacuum. The angular position of the target inside the chamber is solved using only phase index and phase velocity, while the ranging effects due to travel from air to glass to vacuum/air are solved with group index and group velocity. When all parameters are solved simultaneously, an absolute knowledge of the position of each target within an environmental chamber can be derived. Novel features of this innovation include measuring absolute position of targets through multiple dispersive and non-dispersive media, deconstruction of lidar raw data from a commercial off-the-shelf unit into reworkable parameters, and use of group velocities to reduce range data. Measurement of structures within a vacuum chamber or other harsh environment, such as a furnace, may now be measured as easily as if they were in an ambient laboratory. This analysis permits transformation of the raw data into absolute spatial units (e.g., mm). This technique has also been extended to laser tracker, theodolite, and cathetometer measurements through refractive media.

Kubalak, David↗
NASA NTRS2000

Constraints on Martian Soil Composition as Inferred from Viking XRFS and Pathfinder APXS and IMP Data

With the successful operation of the Alpha Proton X-Ray Spectrometer (APXS) during 1997's Mars Pathfinder (MPF) mission, geochemistry data are now available from three sites on Mars. APXS raw spectra for six soils and five rocks have been converted to compositional abundances. The Viking Lander X-Ray Fluorescence Spectrometer (XRFS) successfully measured elemental abundances of nine soils at Viking 1 and eight soils at Viking 2. Although the three landing sites are located in different parts of Mars, the soils exhibit broad similarities, with an iron-rich chemistry similar to that of palagonite. However, the Pathfinder sods show some significant differences from Viking soils, notably an enrichment in silica and depletion in sulfur. The XRFS samples consisted of near-surface and deep (up to 22 cm) soils acquired by a collector head at the cod of a retractable boom. It was possible to collect and analyze pebbles as large a 2 cm, but only sod, some in the form of consolidated clods, was sampled. In contrast, the APXS measured materials in situ. This resulted in MPF "rock" analyses that probably had a significant dust component and, as explored here, "soil" analyses that may have contained a rocky component We examine several possibilities to explain these differences and other attributes of the APXS and XRFS data sets: 1) The APXS soil measurements actually sampled a mixture of Viking-like soil and small bits of high-silica, low-sulfur rock, 2) The soils were derived from high-silica rocks mixed with a minor component of globally-homogenized dust; these soils are chemically distinct and have a separate geologic history from the Viking soils. 3) The weathering environment was different at the Pathfinder landing site compared to the Viking sites, and 4) Uncertainties in the XRFS and APXS measurements result in reported elemental abundances different than those that are actually present We show that none of the possibilities can be discounted, but that an MPF soil distinct in composition from Viking sods is best supported by the available data.

Bridges, N. T.↗
DOE OSTI2019

Development of Multicomponent EAM Potential for Ni-Based Superalloy

We initiated the development of multi-component EAM potentials for Aluminides and Carbides, key phases in Ni-based Superalloys. The goal is to utilize the MD simulation to understand the deformation dynamics that contribute to the formation of voids and creep initiation. For this purpose, we constructed the raw data from ab-initio (molecular dynamics) MD simulations fed into the potential development code and used Nickel as the base metal with the addition of a number of various elements including Aluminum, Chromium, Tungsten. We then developed the EAM potentials for the aluminide and carbide phases using the force-fitting code MEAMfit. Our generated potential reproduces the fundamental properties of the Ni3Al and Mo23C6 phases. We verified further the EAM potential through the thermal stability test at different temperatures and by reproducing the elastic constants consistent with the experimental values.

36 MATERIALS SCIENCE↗
DOE OSTI2022

FTICR-MS, Sensor, and Environmental Data from 5 Streams Impacted by the 2020 Holiday Farm Fire Associated with: "Spatiotemporal controls on the delivery of dissolved organic matter to streams following a wildfire"

This data package is associated with the publication "Spatiotemporal Controls on the Delivery of Dissolved Organic Matter to Streams Following a Wildfire" submitted to Geophysical Research Letters (Roebuck et al., 2022). The study aims to understand storm induced transport of pyrogenic materials to streams impacted by varying degrees of burn severity. Time series samples (24 samples in 1-hour intervals) were collected at 5 sites within the McKenzie River Watershed (Oregon, USA) whose catchment were each completely engulfed by the 2020 Holiday Farm Fire. The samples were collected in November 2020 during the first major storm pulse following the conclusion of the wildfire. Samples were characterized for dissolved organic carbon, total dissolved nitrogen, and by ultra-high resolution mass spectrometry. In situ turbidity data also collected.This data package contains 4 primary folders that include the following: 1) Metadata, 2) EnvData (Environmental Data), 3) SensorData, and 4) FTICR_SupportingData. The package contains a single file-level metadata (flmd) file. Each primary folder also contains individual data dictionaries (dd) to define and provide descriptors of column/row headers and data flags. The FTICR_SupportingData, folder 4, contains raw, unprocessed FTICR-MS Data files in addition to a csv containing processed FTICR-MS data. This package contains the following file types: csv, xml, pdf.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1976

Electrolytic pretreatment unit gaseous effluent conditioning

The electrolytic pretreatment of urine is an advanced process that eliminates the need for handling and storing the highly corrosive chemicals that are normally used in water reclamation systems. The electrolytic pretreatment process also converts the organic materials in urine to gases (N2 and O2) that can be used to replenish those lost to space by leakage, venting, and air lock operations. The electrolytic process is more than a pretreatment, since it decreases the urine solids content by approximately one third, thus reducing the load and eventual solids storage requirements of the urine processing system. The evolved gases from the pretreatment step cannot, however, be returned directly to the atmosphere of a spacecraft without first removing several impurities including hydrogen, chlorine, and certain organic compounds. A treatment concept was developed that would decrease the impurities in the gas stream that emanates from an electrolysis unit to levels sufficiently low to allow the conditioned gas stream to be safely discharged to a spacecraft atmosphere. Two methods were experimentally demonstrated that can accomplish the desired cleanup. The bases of the two methods are, repectively: (1) raw urine scrubbing and (2) silica gel sorption.

Colombo, G. V.↗
DOE OSTI2022

Machine Learning assisted optimization and parameter space exploration dataset of spin ice Hamiltonian

This repository contains both simulated and experimental structure factor data for the data challenge involving the inverse scattering problem. The simulated data were generated during a machine-learning-assisted optimization routine described in ref[1]. The experimental structure factor was measured on a rare-earth oxide, Dy2Ti2O7 using diffuse neutron scattering from time-of-flight techniques on the CORELLI instrument at the Spallation Neutron Source, Oak Ridge National Laboratory. A Metropolis Monte Carlo code implemented to run in a High-performance computing setting was used to calculated simulated structure factors for the spin-ice Hamiltonian at 680 mK, which is the same temperature as for the experimental data. The total size of all the files in this repository is 5.12 GB. A detailed description of the files is given below. ExperimentalData_630mK.dat – A linearized version of 3-dimensional experimental data of size 61×81×21. This data was processed to remove an estimation of non-magnetic background, including nuclear scattering signal and instrumentation background. Parameters.dat – 6700 samples were evaluated over the 4-dimensional parameter space (J_1, J_2, J_3 and J_(3^' )). There is an additional parameter, D in the spin Hamiltonian to mimic the dipolar interaction between magnetic ions. However, this parameter, D was fixed to a value determined by prior work. This file contains five columns for the parameters J_1, J_2, J_3, J_(3^' ) and D respectively. 3D_Simulation_Data.dat – The simulated structure factor, S(Q) data are included in this file. Each raw contains a linearized array of 3D volumes of S(Q) calculated for the parameter set given in the corresponding row of the file Parameters.dat. The size of the volume data was matched to the experimental data. Qx(h,-h,0).dat, Qy(k,k,-2k).dat, Qz(l,l,l).dat – These files contain the h, k, and l values along with the reciprocal vectors [h,-h,0], [k,k,-2k] and [l,l,l] respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fiscal Year 2020 Filtration of Hanford Tank Waste 241-AP-105

Bench-scale filtration testing of 15 liters of 241-AP-105 supernatant was conducted using a Mott inline filter Model 6610 (media grade 5) backpulsed dead-end filter (BDEF) in the hot cells of the Radiochemical Processing Laboratory at Pacific Northwest National Laboratory. The as-received samples were diluted with raw water from the Hanford Site to assess the propensity for solids to form upon dilution and to assess the impact those solids have on filtration performance. The feed was split into two batches. The first batch was settled and decanted as planned in Tank Side Cesium Removal operations. The BDEF was used to filter this AP-105 feed at a targeted flux of 0.065 gpm/ft 2 and exhibited no measurable pressure increase during filtration. The second batch was fed to the BDEF with solids resuspended. This was also operated at the targeted flux of 0.065 gpm/ft 2 . In this case, the target pressure differential of 2 psid (resistance of 6.24 × 10 10 m -1 ) was reached in slightly more than 12 h. A backpulse restored the filter flux; however, the time to the next backpulse was slightly shorter. These tests indicate that after the addition of raw water, settle and decant effectively removed solids from the feed. It is not possible to assess the time required for these solids to settle based on the result from these tests. However, if sufficient time is allowed for the solids to settle, no measurable filter fouling was observed in current testing. In contrast, if insufficient time is allowed for solids to settle, filter fouling will occur relatively quickly and will likely require backpulses more frequently than every 12 hours (1.91 m 3 /m 2 volume filtered). Solids concentrated from backpulse solutions displayed large variability in composition with Al-silicates and mixed chromium-aluminum oxide phases. Amounts of Mg, Fe, and Ca were also found in the presence of Na and O. These solids could be grouped in three categories: (1) soluble Na-salts that formed large block-like particles but were made up of fibrous materials, (2) amorphous Al-phases, and (3) colloidal iron oxides with an average particle diameter of 4.2 µm.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Vaporization behavior of Ir 4 (CO) 12 and Re 2 (CO) 10 measured by torsion effusion gravimetric method

Metal carbonyls are of great importance in chemical vapor deposition (CVD), composite materials fabrication, and other near-net shape technologies. Carbonyl CVD is used for deposition of high-purity metallic and alloy coatings for which vapor pressure data is essential. In this study, we report vapor pressures of solid Ir 4 (CO) 12 and Re 2 (CO) 10 carbonyls measured by using the Knudsen Cell methodology using a torsion effusion thermogravimetric system. The vapor pressure of the Ir 4 (CO) 12 exhibited incongruent vaporization, as the molecular weight (MW) of the effusing species was determined as 128 g/mol as compared to the theoretical MW of 1105 g/mol. It is proposed that the Ir 4 (CO) 12 (s) partially decomposed (~66%) to Ir 4 (CO) 12 (g), Ir(s), and CO(g). The Re 2 (CO) 10 on the other hand, showed congruent behavior with Re 2 (CO) 10 (s) vaporizing to Re 2 (CO) 10 (g) in the measured temperature range. The raw data for vapor pressures was measured using two sets of Knudsen cells with different orifice sizes, and the equilibrium vapor pressures were calculated using Whitman-Motzfeldt methodology. The equilibrium vapor pressures of these carbonyls, partial pressures of gaseous species in case of decomposition, average molecular weights of the effusing gasses were determined. The vapor pressures and Gibbs energies of vaporization reactions of the two above mentioned carbonyls, as well as comparison of vaporization thermodynamics these two carbonyls with other carbonyls from Group VIB to VIIIB are presented in this work.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗