Thermally drawn rechargeable battery fiber enables pervasive power
Explore the source record for details and available documents.
Khudiyev, Tural↗
SEARCH · Engineering Papers
Results for “protective structures”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
High-Level Considerations for Access and Access Controls by Design
The design and construction of a nuclear power plant must include robust structures and a security boundary that is difficult to penetrate. For security considerations, the reactors would ideally be sited underground, beneath a massive solid block, which would be too thick to be penetrated by tools or explosives. Additionally, all communications and power transfer lines would also be located underground and would be fortified against any possible design basis threats. Limiting access with difficult-to-penetrate physical barriers is a key aspect for determining response and staffing requirements. Considerations considered in a graded approach to physical protection are described.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Compilation and Evaluation of Data from Groundwater Impounded within the U12n and U12t Tunnels, Rainier and Aqueduct Mesas, Nevada National Security Site
The Department of Defense (DOD) Defense Threat Reduction Agency (DTRA) and the U.S. Department of Energy (DOE) Office of Environmental Management Nevada Program (EM NV) conducted routine physical and geochemical monitoring of water impounded behind impermeable structures placed within the U12n and U12t tunnels on the Nevada National Security Site (NNSS) (formerly the Nevada Test Site [NTS]). Desert Research Institute (DRI) conducted a semiquantitative evaluation of pressure data to determine the extent to which the tunnels have been inundated and a qualitative evaluation of monitored geochemical parameters to determine if trends exist that were indicative of hydrologic and/or geochemical processes operating behind the tunnel plugs. Data were also evaluated to determine if monitored radiological parameters exceeded primary standards associated with the Environmental Protection Agency’s (EPA) Safe Drinking Water Act (SDWA) (40 C.F.R. § 141.66).
54 ENVIRONMENTAL SCIENCES↗
Waste to worth: A high-temperature water-gas shift magnetite catalyst with encapsulated core-shell structure from coal fly ash
In this paper, we demonstrate the synthesis of magnetite-based, encapsulated catalyst with a core-shell structure from coal fly ash, an industrial solid waste, and its application to industrially important high temperature water-gas shift reaction (HT-WGSR). The catalyst precursor was first synthesized through a leaching-precipitation-hydrothermal process, leading to the formation of a nanosheet-like hematite precursor consisting of Fe 3+ as primary element and minor cations including Al 3+ , Mg 2+ and other cations (e.g. Ca 2+ and Ti 4+ ). During the WGSR, the nanosheets broke into smaller particles with a core of magnetite with a diameter of ~20 nm, whereas the inherent impurity elements were activated and migrated to the outer surface forming a shell with a thickness of ~4 nm. Due to the protection of shell, the as-synthesized catalyst exhibited improved activity, thermal stability and long-term durability for HT-WGSR at 400 °C and 450 °C. Compared to the pure hematite, this catalyst exhibited much higher activity and stability, i.e., increased CO conversion and decreased deactivation rate constant, by a factor of four and three, respectively. Additionally, through a bottom-up reverse synthesis, we have confirmed that Al 3+ functioned as a textual promoter enhancing the interfacial area of the catalyst. On the other hand, the presence of minor impurity elements, in particular 2.58 wt% Mg 2+ and 0.18 wt% Ti 4+ , were found to increase the basicity, and promote the adsorption rate of CO, the redox of catalysts, and the alteration of the reaction mechanism from regenerative to associative with the formation of a strong intermediate formate. Finally, this study not only opens a new direction on the valorization of solid waste into high-value catalysts, promoting the sustainability of solid waste management, but also provides an alternative, cost-effective and scalable approach for the design and fine-tuning of encapsulated catalysts.
01 COAL, LIGNITE, AND PEAT↗
A tyrosine phosphoregulatory system controls exopolysaccharide biosynthesis and biofilm formation in Vibrio cholerae
Production of an extracellular matrix is essential for biofilm formation, as this matrix both secures and protects the cells it encases. Mechanisms underlying production and assembly of matrices are poorly understood. Vibrio cholerae, relies heavily on biofilm formation for survival, infectivity, and transmission. Biofilm formation requires Vibrio polysaccharide (VPS), which is produced by vps gene-products, yet the function of these products remains unknown. Here, we demonstrate that the vps gene-products vpsO and vpsU encode respectively for a tyrosine kinase and a cognate tyrosine phosphatase. Collectively, VpsO and VpsU act as a tyrosine phosphoregulatory system to modulate VPS production. We present structures of VpsU and the kinase domain of VpsO, and we report observed autocatalytic tyrosine phosphorylation of the VpsO C-terminal tail. The position and amount of tyrosine phosphorylation in the VpsO C-terminal tail represses VPS production and biofilm formation through a mechanism involving the modulation of VpsO oligomerization. We found that tyrosine phosphorylation enhances stability of VpsO. Regulation of VpsO phosphorylation by the phosphatase VpsU is vital for maintaining native VPS levels. This study provides new insights into the mechanism and regulation of VPS production and establishes general principles of biofilm matrix production and its inhibition.
59 BASIC BIOLOGICAL SCIENCES↗
Digital Assurance for Grid Reliability in the Era of Large Load Growth
The rapid expansion of large electric loads is reshaping the operational and regulatory landscape of the U.S. electric grid. These facilities are reaching new scales of expansion, now exceeding a gigawatt per site, and their highly sensitive, digitally driven behaviors introduce new reliability risks. Recent grid events, including large load losses following routine transmission disturbances, highlight the consequences of limited ride-through capability, inconsistent protection settings, inadequate modeling, and lack of behind-the-meter visibility. Parallels to earlier integration challenges of new grid technologies suggest that the grid’s existing processes, standards, and interconnection frameworks are no longer adequate for emerging large loads. This brief synthesizes lessons from the evolution of inverter-based resource regulation and applies them to large-load integration. It identifies critical gaps in modeling accuracy, interconnection processes, performance standards, and compliance mechanisms. Technical recommendations emphasize advanced monitoring, improved modeling, coordinated communication protocols, modernized substations, and structured behind-the-meter control schemes. Collectively, these measures provide a roadmap to maintain bulk power system reliability while enabling the continued growth of large, electrified digital infrastructure.
24 - POWER TRANSMISSION AND DISTRIBUTION↗
High Temperature Ternary Chloride Molten Salt Pump
This work investigates the design criteria considering thermal, structural, and mate-rial selection of a ternary chloride (MgCl2-NaCl-KCl) molten salt pump that is capable of running at temperatures above 720 °C. In this work, preliminary testing of salt-wetted hydrodynamic bearings was done to investigate different material pairings including colmonoy grades, stellite grades, and a novel NiWC-based alloy (i.e. HybrimetTM NiWC3b) used as a High Velocity Ox-ygen Fuel (HVOF) coating. The coating has shown to withstand the corrosive nature of the salt, and is additionally used to protect a 316L stainless steel pump reservoir. The pump wetted components are made of Inconel 625, and it features a carbon ring seal developed by Flows-erve flooded with a N2 gas flow on the overhead to keep salt vapors from interacting with the external ambient air. This research showcases a promising design for use in the CSP Gen 3 liquid-pathway and sets the ground for further development and use of the HybrimetTM NiWC3b as a competitive alternative to available superalloys. Further work will further characterize the pump by performance & cycle testing in molten salt at higher temperatures.
14 SOLAR ENERGY↗
Iron-rich microstructure records of high temperature multi-component silicate melt behavior in nuclear fallout
Above-ground nuclear explosions that interact with the surface of the earth entrain materials from the surrounding environment, influencing the resulting physical and chemical evolution of the fireball, which can affect the final chemical phase and mobility of hazardous radionuclides that are dispersed in the environment as fallout particles. The interaction of iron with a nuclear explosion is of specific interest due to the potential for iron to act as a redox buffer and because of the likelihood of significant masses of metals to be present in urban environments. We investigated fallout from a historic surface interacting nuclear explosion conducted on a steel tower and report the discovery of widespread and diverse iron-rich micro-structures preserved within the samples, including crystalline dendrites and micron-scale iron-rich spheres with liquid immiscibility textures. We assert these micro-structures reflect local redox conditions and cooling rates and can inform interpretation of high temperature events, enabling new insights into fireball condensation physics and chemistry when metals from the local environment (i.e. structural steel) are vaporized or entrained. Finally, these observations also significantly expand the availability of silicate immiscibility datasets applicable to rapidly quenched systems such as meteorite impact melt glass.
38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
Lipid sponge droplets as programmable synthetic organelles
Living cells segregate molecules and reactions in various subcellular compartments known as organelles. Spatial organization is likely essential for expanding the biochemical functions of synthetic reaction systems, including artificial cells. Many studies have attempted to mimic organelle functions using lamellar membrane-bound vesicles. However, vesicles typically suffer from highly limited transport across the membranes and an inability to mimic the dense membrane networks typically found in organelles such as the endoplasmic reticulum. Here, we describe programmable synthetic organelles based on highly stable nonlamellar sponge phase droplets that spontaneously assemble from a single-chain galactolipid and nonionic detergents. Due to their nanoporous structure, lipid sponge droplets readily exchange materials with the surrounding environment. In addition, the sponge phase contains a dense network of lipid bilayers and nanometric aqueous channels, which allows different classes of molecules to partition based on their size, polarity, and specific binding motifs. The sequestration of biologically relevant macromolecules can be programmed by the addition of suitably functionalized amphiphiles to the droplets. We demonstrate that droplets can harbor functional soluble and transmembrane proteins, allowing for the colocalization and concentration of enzymes and substrates to enhance reaction rates. Droplets protect bound proteins from proteases, and these interactions can be engineered to be reversible and optically controlled. Our results show that lipid sponge droplets permit the facile integration of membrane-rich environments and self-assembling spatial organization with biochemical reaction systems.
59 BASIC BIOLOGICAL SCIENCES↗
Accessing the Spectral Function in a Current-Carrying Device
The presence of an electrical transport current in a material is one of the simplest and most important realizations of nonequilibrium physics. The current density breaks the crystalline symmetry and can give rise to dramatic phenomena, such as sliding charge density waves, insulator-to-metal transitions, or gap openings in topologically protected states. Almost nothing is known about how a current influences the electron spectral function, which characterizes most of the solid’s electronic, optical, and chemical properties. In this work, we show that angle-resolved photoemission spectroscopy with a nanoscale light spot provides not only a wealth of information on local equilibrium properties, but also opens the possibility to access the local nonequilibrium spectral function in the presence of a transport current. Unifying spectroscopic and transport measurements in this way allows simultaneous noninvasive local measurements of the composition, structure, many-body effects, and carrier mobility in the presence of high current densities. In the particular case of our graphene-based device, we are able to correlate the presence of structural defects with locally reduced carrier lifetimes in the spectral function and a locally reduced mobility with a spatial resolution of 500 nm.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Effects of elevated temperature exposure on the residual stress state and microstructure of PVD Cr coatings on SiC investigated via in situ X-ray diffraction and transmission electron microscopy
Pure Cr coatings are being considered as corrosion-resistant layers for SiC-SiC f composite fuel cladding in light water reactors. The residual stress state and interdiffusion behavior of Cr coatings deposited on SiC substrates using bipolar high-power impulse magnetron sputtering (B-HiPIMS) and direct current impulse magnetron sputtering (DCMS) were studied using in situ X-ray diffraction experiments at 300 °C, 700 °C, and 1200 °C. After elevated temperature exposure, evolution of the coating microstructure and coating/substrate interdiffusion was characterized by transmission electron microscopy. The compressive residual stress of the dense B-HiPIMS coating at room temperature was gradually relieved at 300 °C, while the stress transitioned to a tensile state at 700 °C. Grain growth of the Cr coating and a Cr–SiC interdiffusion layer consisting of newly formed Cr–C and Cr–Si phases were observed in the B-HiPIMS coating after exposure at 700 °C. The phases in the interdiffusion layer were identified to be Cr 7 C 3 , Cr 3 Si, and Cr 5 Si 3 C x experimentally and by thermodynamic predictions. For the DCMS coating, however, changes in residual stress and microstructure at the elevated temperatures were limited by the inherent porosity and inhomogeneous structure of the as-deposited coating. At 1200 °C, both coating types interacted rapidly with the underlying SiC substrate in the early stages of the experiment. The results from this study suggest that the characteristics of the Cr coatings do not significantly change at the reactor operating temperature of 300 °C, while changes in microstructure and stress state are expected in off-normal conditions of 700 °C and 1200 °C. Finally the results from this study suggest the B-HiPIMS coating is best-suited as a protective coating for SiC fuel cladding.
36 MATERIALS SCIENCE↗
Success Using A Granular-Activated Carbon Filtration Swab to Rehabilitate Westbay{sup R} Multi-level Groundwater Monitoring Wells at the INL - 20544
In November 2015, tetrachloroethylene (PCE) was discovered in groundwater samples collected from a Westbay{sup R} multi-level groundwater monitoring well at the Idaho National Laboratory (INL).a Subsequent investigation determined that PCE was not present in the groundwater. The detected PCE was instead due to inadvertent contamination of the internal tubing fluid in the Westbay well-monitoring system, which is isolated from the surrounding groundwater. Further investigation showed that three of the 11 Westbay wells at the INL contained PCE-contaminated tubing fluid at concentrations above the U.S. Environmental Protection Agency's maximum contaminant level for drinking water (5 μg/L). Loose sediment at the bottom of some Westbay wells was also found to contain PCE; the three wells were then identified for rehabilitation as part of the INL well maintenance program. The unique construction of the Westbay wells - i.e., the small diameter (5.72 cm [2.25 in.]) and the depths of the tubing fluid ranging from 144.8 to 419 m (475 to 1,376 ft) below ground surface - posed unique challenges to the rehabilitation. Because the tubing fluid provides structural integrity, the fluid cannot be removed and then replaced without damaging the integrity of the Westbay well. Additionally, the small diameter of the systems and the associated depths limit the availability of equipment that can be used for the rehabilitation. After an evaluation of potential methods, it was determined that the use of an in-well, custom-fabricated, granular-activated-carbon filtration swab deployed via a wire line would provide the safest and most cost-effective method for rehabilitation. Westbay well rehabilitation started at well MIDDLE-2051 in late June 2018 and paused in December 2018 for the season. The PCE concentration in the tubing fluid at MIDDLE-2051 was initially reduced to a maximum concentration of 3.81 μg/L from a maximum of 642 μg/L, while the concentration of PCE in the sediment had been reduced from 5,360 to 2,270 μg/kg. Sampling was performed at MIDDLE-2051 again in August 2019, and the tubing fluid increased to a maximum concentration of 45.4 μg/L, while the concentration in the sediment decreased further to 1,890 μg/kg due to desorption of PCE from the sediment to the tubing fluid. Rehabilitation resumed at well MIDDLE-2050A in late August 2019, and the PCE concentration in the tubing fluid had been reduced to a maximum concentration of 19.0 μg/L. Although the method has been shown to be time-consuming, it has proven to be effective and safe for personnel performing the work and to the integrity of the well. Future sample data results at all wells will help determine an estimated completion of the rehabilitation. (authors)
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Organic carbon feedbacks to soil structure in Profundihumic and Haplic Ferralsols in Campinas, Sao Paulo, Brazil
Increasing soil organic matter content coincides with increasing soil porosity and decreasing bulk density, but the mechanisms that lead to changes in soil structure are unclear. We quantified and compared soil characteristics across two contrasting soils (heavily weathered ferralsols in Brazil) to clarify the effects of organic matter content on soil porosity. We found that high organic matter content fosters higher biologic activity, including root growth and animal burrowing, which in turn increase soil porosity and decreases bulk density.This dataset includes soil physical, morophological, and chemical variables from 6 soil profiles were sampled in Campinas, Sa ̃o Paulo state, southeastern Brazil to 1 m depth. Sites are regenerated mixed savanna and rainforest in the protected area of Viracopos Airport in Campinas, lightly grazed by cattle.This dataset includes soil color, bulk density, texture (percent sand, silt, clay, and coarse fragments as well as class), soil pH, cation exchange capacity, C stock, C concentration, N stock, N concentration, delta 13C, Delta 14C, and soil porosity in Excel and csv format.
54 ENVIRONMENTAL SCIENCES↗
Resilient Operation of Networked Community Microgrids with High Solar Penetration
This project, funded by the US Department of Energy’s Solar Energy Technologies Office (SETO), focused on the operation of microgrids as a coordinated network. The primary objective, which was successfully achieved, was to develop both control strategies and hardware solutions to support the resilient and efficient operation of networked microgrids with high solar penetration. The work was structured around the following four main tasks: • Development of distributed and scalable optimization algorithms for AC-coupled networked microgrids. • Design and implementation of a novel DC interconnection hardware to enable precise power exchange between microgrids. • Laboratory operational validation of the developed technologies using 480 V testbeds and commercially available hardware. • Field operational validation of the complete solution in Adjuntas, Puerto Rico, interconnecting two kW-scale, split-phase microgrids of Casa Pueblo’s microgrids. This project addressed multiple technical challenges across the domains of optimization, control, hardware interconnection, and protection. One of its key contributions was delivering tangible, real-world solutions for networking microgrids. In contrast to purely theoretical or simulation-based work, this project included full-scale hardware operational validation both in the lab and in the field. The work conducted as part of this project—in collaboration with the University of Puerto Rico; the University of Tennessee, Knoxville; the University of Central Florida; and Casa Pueblo—has advanced the state of the art in networked microgrids. Key contributions include the development of distributed control strategies, practical solutions for real-world implementation challenges, and the introduction of a novel DC interlink approach for microgrid interconnection. The project featured both laboratory and field validation using commercial off-the-shelf components. The field deployment successfully validated that a group of microgrids can operate in a coordinated manner, enabling precise power flow between systems and mutual support during extreme events. This project resulted in 15 journal publications and 15 conference papers; 5 graduate students and 15 undergraduate students were supported. The codes of distributed optimization and forecasting were made open-source through OSTI.gov for distributed optimization and forecasting. All the publications are available in the ORNL-hosted project landing page. The DC interlink with state-of-charge balancing control was operationally validated in Adjuntas by interconnecting two real-world, 240 V split-phase microgrids. To the best knowledge of the team, this represents the first operational validation of AC microgrids interconnected via DC-interlinks. As a culmination of this project, a follow-on grant was awarded to support the technology transfer of the distributed optimization framework to a commercial microgrid controller, Stellar Edge, developed by the California-based company New Sun Road.
14 SOLAR ENERGY↗
Topology-enhanced mechanical stability of swelling nanoporous electrodes
Abstract Materials like silicon and germanium offer a 10-fold improvement in charge capacity over conventional graphite anodes in lithium-ion batteries but experience a roughly threefold volume increase during lithiation, which challenges ensuring battery integrity. Nanoporous silicon, created by liquid-metal-dealloying, is a potentially attractive anode design to mitigate this challenge, exhibiting both higher capacity and extended cycle lifetimes. However, how nanoporous structures accommodate the large volume change is unknown. Here, we address this question by using phase-field modeling to produce nanoporous particles and to investigate their elastoplastic swelling behavior and fracture. Our simulations show that enhanced mechanical stability results from the network topology consisting of ligaments connected by bulbous, sphere-like nodes. The ligaments forcefully resist elongation while the nodes, behaving like isolated spherical particles, experience large stresses driving fracture. However, being smaller compared to a sphere of the same volume as the entire nanoporous particle, the nodes are more protected against fracture.
36 MATERIALS SCIENCE↗
Selection and development of aptamers for pyoverdine
The rhizosphere is a small region surrounding plant roots that is enriched in biochemicals from root exudates and populated with fungi, nematode, and bacteria. Interaction of rhizosphere organisms with plants is mainly promoted by exudates from the roots. Root exudates contain biochemicals that come from primary and secondary metabolisms of plants. These biochemicals attract microbes, which influence plant nutrition. The rhizosphere bacteria (microbiome) are vital to plant nutrient uptake and influence biotic and abiotic stress and pathogenesis. Pseudomonas is a genus of gammaproteobacteria known for its ubiquitous presence in natural habitats and its striking ecological, metabolic, and biochemical diversity. Within the genus, members of the Pseudomonas fluorescens group are common inhabitants of soil and plant surfaces, and certain strains function in the biological control of plant disease, protecting plants from infection by soilborne and aerial plant pathogens. The soil bacterium Pseudomonas protegens Pf-5 (also known as Pseudomonas fluorescensPf-5) is a well-characterized biological strain, which is distinguished by its prolific production of the secondary metabolite, pyoverdine. Knowledge of the distribution of P. fluorescens secretory activity around plant roots is very important for understanding the interaction between P. fluorescens and plants and can be achieved by real time tracking of pyoverdine. To achieve the capability of real-time tracking in soil, we have used a structure-switching SELEX strategy to select high affinity ssDNA and 2’ F-Y-RNA aptamers with specificity for pyoverdine over other siderophores. Pyoverdines from various strains possess a conserved chromophore along with strain-specific peptide chain. Some of the isolated aptamers bind to chromophore of pyoverdine. These will identify pyoverdines from a variety of pseudomonads. Identification of aptamers that selectively bind the peptide portion of pyoverdine Pf-5 is underway. The identified aptamers that are broadly and narrowly specific for pyoverdines or Pf-5 will be optimized for integration into an electrochemical biosensor to track, in real time, P fluorescens activity and other pseudomonads in and around the rhizosphere.
59 BASIC BIOLOGICAL SCIENCES↗
Assessing residential activity in a home plumbing system simulator: monitoring the occurrence and relationship of major opportunistic pathogens and phagocytic amoebas
Opportunistic premise plumbing pathogens (OPPPs) have been detected in buildings’ plumbing systems causing waterborne disease outbreaks in the United States. In this study, we monitored the occurrence of OPPPs along with free-living amoeba (FLA) and investigated the effects of residential activities in a simulated home plumbing system (HPS). Water samples were collected from various locations in the HPS and analyzed for three major OPPPs: Legionella pneumophila, nontuberculous mycobacterial species (e.g., Mycobacterium avium, M. intracellulare, and M. abscessus), and Pseudomonas aeruginosa along with two groups of amoebas (Acanthamoeba and Vermamoeba vermiformis). A metagenomic approach was also used to further characterize the microbial communities. Results show that the microbial community is highly diverse with evidence of spatial and temporal structuring influenced by environmental conditions. L. pneumophila was the most prevalent pathogen (86% of samples), followed by M. intracellulare (66%) and P. aeruginosa (21%). Interestingly, M. avium and M. abscessus were not detected in any samples. The data revealed a relatively low prevalence of Acanthamoeba spp. (4%), while V. vermiformis was widely detected (81%) across all the sampling locations within the HPS. Locations with a high concentration of L. pneumophila and M. intracellulare coincided with the highest detection of V. vermiformis, suggesting the potential growth of both populations within FLA and additional protection in drinking water. After a period of stagnation lasting at least 2-weeks, the concentrations of OPPPs and amoeba immediately increased and then decreased gradually back to the baseline. Furthermore, monitoring the microbial population after drainage of the hot water tank and partial drainage of the entire HPS demonstrated no significant mitigation of the selected OPPPs. This study demonstrates that these organisms can adjust to their environment during such events and may survive in biofilms and/or grow within FLA, protecting them from stressors in the supplied water.
59 BASIC BIOLOGICAL SCIENCES↗
ATCUN-like Copper Site in βB2-Crystallin Plays a Protective Role in Cataract-Associated Aggregation
Cataract is the leading cause of blindness worldwide, and it is caused by crystallin damage and aggregation. Senile cataractous lenses have relatively high levels of metals, while some metal ions can directly induce the aggregation of human γ-crystallins. Here, for this work, we evaluated the impact of divalent metal ions in the aggregation of human βB2-crystallin, one of the most abundant crystallins in the lens. Turbidity assays showed that Pb 2+ , Hg 2+ , Cu 2+ , and Zn 2+ ions induce the aggregation of βB2-crystallin. Metal-induced aggregation is partially reverted by a chelating agent, indicating the formation of metal-bridged species. Our study focused on the mechanism of copper-induced aggregation of βB2-crystallin, finding that it involves metal-bridging, disulfide-bridging, and loss of protein stability. Circular dichroism and electron paramagnetic resonance (EPR) revealed the presence of at least three Cu 2+ binding sites in βB2-crystallin, one of them with spectroscopic features typical for Cu 2+ bound to an amino-terminal copper and nickel (ATCUN) binding motif, which is found in Cu transport proteins. The ATCUN-like Cu binding site is located at the unstructured N-terminus of βB2-crystallin, and it could be modeled by a peptide with the first six residues in the protein sequence (NH 2 -ASDHQF-). Isothermal titration calorimetry indicates a nanomolar Cu 2+ binding affinity for the ATCUN-like site. An N-truncated form of βB2-crystallin is more susceptible to Cu-induced aggregation and is less thermally stable, indicating a protective role for the ATCUN-like site. EPR and X-ray absorption spectroscopy studies reveal the presence of a copper redox active site in βB2-crystallin that is associated with metal-induced aggregation and formation of disulfide-bridged oligomers. Our study demonstrates metal-induced aggregation of βB2-crystallin and the presence of putative copper binding sites in the protein. Whether the copper-transport ATCUN-like site in βB2-crystallin plays a functional/protective role or constitutes a vestige from its evolution as a lens structural protein remains to be elucidated.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗