Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “point contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Development of a Novel Helmet Support Assembly for NASA Orion Crew Survival Suit

Orion Spacecraft water landing environments have necessitated the design and testing of a novel Helmet Support Assembly (HSA) as part of the NASA Orion Crew Survival Systems (OCSS) launch and re-entry spacesuit. A series of development sled tests using 5 th female, 50th male, and 95th male Hybrid III Anthropometric Test Devices (ATDs) simulated worst case water landings and identified the need for an integrated suit countermeasure to control the helmet during dynamic loading. Initial prototype countermeasures rigidly restrained the helmet keeping the helmet in place as desired, but led to large force and moment transmission to the upper neck. Further development led to a flexible HSA which used high-strength steel wire contoured to the size-matched ATD thorax and attached to both the front and rear of the neck ring. The selected wire diameter and contoured shape provided some ability to flex under the expected worst-case dynamic loads. The existing shoulder harness was used to restrain the helmet motion during “eyeballs out/down” loading while also attempting to prevent head-to-helmet contact in “eyeballs down” spinal-axis loading. A new small prototype helmet was also developed and tested for the 5th and 50th ATDs with both HSA devices. Dynamic impact tests were conducted on the HIA (Horizontal Impulse Accelerator) at Wright Patterson Air Force Base (WPAFB) under simulated off-nominal landing conditions using a representative Orion seat and 5-point harness. For each ATD size, peak Neck Injury Criteria (Nij) were compared to equivalent sled tests with an unsuited ATD configuration. Adding a helmet without attempting to control motion increased peak Nij values for all ATD sizes. The use of the rigid countermeasure showed decreased peak Nij results for the 5th female, but increased peak Nij values for both 50th configurations and the 95th male ATDs. By comparison, the flexible HSA showed reduced peak Nij values for all ATD sizes. Overall, this series of dynamic impact tests identified a risk of increased crew neck loading when under- or over-restraining the helmet during simulated Orion water landings and also demonstrated an effective strategy to mitigate those loads with a compliant HSA design.

Safety↗
DOE OSTI2021

BCJ amplitude relations for Anti-de Sitter boundary correlators in embedding space

We generalize the color/kinematics duality of flat-space scattering amplitudes to the embedding space formulation of AdS boundary correlators. Kinematic numerators and propagators are replaced with differential operators acting on a scalar contact diagram that is the AdS generalization of the momentum conserving delta function of flat space scattering amplitudes. We show that color/kinematics duality implies differential relations among AdS boundary correlators that naturally generalize the flat space BCJ amplitude relations and verify them for the correlators of Yang-Mills theory and of the Nonlinear Sigma Model through four- and six-points, respectively. For the latter we also find representations of the four- and six-point correlator that manifest the duality. Possible double-copy procedures in AdS space are also discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Unusual Li 2 O sublimation promotes single-crystal growth and sintering

Li 2 O is rarely used for cathode material synthesis due to its high melting point (1,438 °C). Here we discover that Li 2 O can sublimate at 800-1,000 °C under ambient pressure, opening new possibilities for cathode synthesis. We propose a mechanism that enables synthesis of single crystals-such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) or LiNi 0.9 Mn 0.05 Co 0.05 O 2 (NMC90)-without direct contact with Li 2 O salts. We show that Li 2 O vapour successfully converts spent polycrystalline NMC811 into segregated single crystals without milling or post-treatment. The Li 2 O vapour, derived from Li 2 O solids, diffuses rapidly and reacts with precursors, mimicking a molten-salt environment, which facilitates single-crystal growth. The chemical lithiation process continuously drives Li 2 O sublimation, sintering the crystals. Single crystals derived from Li 2 O and fresh precursors or spent polycrystals exhibit outstanding cycling after 1,000 cycles in full cells. The demonstrated Li 2 O sublimation and its universal role in promoting single-crystal growth provides an effective approach for single-crystal synthesis, scale-up and recycling.

25 ENERGY STORAGE↗
DOE OSTI2020

CRNT4SBML: a Python package for the detection of bistability in biochemical reaction networks

Motivation: Signaling pathways capable of switching between two states are ubiquitous within living organisms. They provide the cells with the means to produce reversible or irreversible decisions. Switchlike behavior of biological systems is realized through biochemical reaction networks capable of having two or more distinct steady states which are dependent on initial conditions. Investigation of whether a certain signaling pathway can confer bistability involves a substantial amount of hypothesis testing. The cost of direct experimental testing can be prohibitive. Therefore, constraining the hypothesis space is highly bene?cial. One such methodology is based on Chemical Reaction Network Theory which uses computational techniques to rule out pathways that are not capable of bistability regardless of kinetic constant values and molecule concentrations. Although useful, these methods are complicated from both pureandcomputationalmathematicsperspectives.Thus,theiradoptionisverylimitedamongstbiologists. Results: We brought Chemical Reaction Network Theory approaches closer to experimental biologists by automating all the necessary steps in CRNT4SMBL. The input is based on SBML format which is the community standard for biological pathway communication. The tool parses SBML and derives C-graph representations of the biological pathway with mass action kinetics. Next steps involve an ef?cient search for potential saddle-node bifurcation points using an optimization technique. This type of bifurcation is important as it has the potential of acting as a switching point between two steady states. Finally, if any bifurcation points are present, numerical continuation analysis extends the equilibria branches for generating the diagram. Presence of an S-shaped bifurcation diagram indicates that the pathway acts as a bistable switch for the given optimization parameters. Availability: CRNT4SBML is available via the Python Package Index. The documentation can be found at https://crnt4sbml.readthedocs.io. CRNT4SBML is licensed under the Apache Software License 2.0. Contact: vladislav.petyuk@pnnl.gov

Reyes, Brandon C.↗
DOE OSTI2023

CCN data from TAMU TRACER campaign in the Houston TX region from July to September 2022

During TRACER, the Texas A&M Rapid Onsite Atmospheric Measurements Van (ROAM-V) was deployed to capture airmasses behind (maritime) and ahead (continental) of the passage of the sea-breeze front through Houston. On select sampling days, ROAM-V sampled in the morning/mid-day on the coast and then transited to a second inland site for the afternoon/evening. The suite of instruments deployed on ROAM-V included a Condensation Particle Counter (CPC; GRIMM Model 5.403 CPC), Scanning Mobility Particle Sizer (SMPS; TSI 3750 detector, TSI 3082 classifier, TSI 3088 neutralizer, TSI 3081A Differential Mobility Analyzer), Cloud Condensation Nuclei counter (Droplet Measurement Technologies CCN Counter), micro pulse lidar (Droplet Measurement Technologies Micro Pulse LiDAR (miniMPL)), and a Davis Rotating Uniform size-cut Monitor (DRUM; DRUMAir 4-DRUM). Before sampling at each location, the latitude and longitude were recorded using the GPS on the phone application “My Altitude”. Onboard the ROAM-V, aerosol samples are drawn through a shared isokinetic inlet at a flow rate ranging from 3.5 to 7.0 LPM. A portion of this flow is directed through a cyclone impactor (Brechtel, Inc. Model SCC 0.732) and 0.5 LPM is directed to the CCN. To calculate particle losses, we used a two-step method. First, the measured SMPS size distributions were used to calculate particle loss through the inlet during sampling. Second, the corrected SMPS data was used to calculate the average of the total losses per scan down the CCN line. Then, the correction was applied to the CCN data. This calculation was done separately for each deployment location due to changes in the measured size distributions between locations. Particle loss from diffusion (based on Kesten, 1991 and Gormley, 1949), inertial impaction in 90-degree bends (based on Aerosol Measurement, 2011 and Crane, 1977), and cyclone impactor efficiency (based on Dirgo, 1985) were included in the loss calculation. When the SMPS was not sampling at a location (in the case of an instrument malfunction or operator error), the reported CPC data was corrected with an average of the total losses for the entire campaign at the specified deployment location (e.g., if we needed to correct Galveston data, then the average of all calculated losses at Galveston was taken). These flatline corrections were used for all data on 22/07/13, 22/07/20, 22/07/22, and the data from Galveston on 22/08/09. The supersaturation uncertainty is estimated conservatively at +/- 0.03%, where variation in the inlet temperature, pressure, and calibration technique prevents a more accurate measurement. Confidence in the reported supersaturation measurements is based on a pre-campaign calibration (following the methods from our previous work and Deng, 2014 based on Rose, 2008) in addition to inter-comparisons with the DOE for two days (22/08/18 and 22/09/01) where TAMU was co-located with AMF1. The inter-comparisons show good agreement between our instrument and the DOEs instrument on both days at all supersaturations. After the last inter-comparison on 22/09/01, there was no indication of a malfunction by our instrument through the rest of the campaign. Unfortunately, the instrument was dropped during demobilization. A post-campaign calibration was conducted, which showed a substantial departure from the pre-campaign calibration. The drop may have damaged the instrument’s ability to produce the desired supersaturations. Therefore, we do consider the data after 22/09/01 to be correct, but it should be used with caution. The CCN counter sampled for 3 minutes at each supersaturation setpoint (0.2, 0.4, 0.6, 0.8, 1.0, and 1.2%). At the end of a cycle, the instrument was set to 0.01% supersaturation for 5 minutes. The data is comprised of the last 60 seconds of each supersaturation set point (0.2, 0.4, 0.6, 0.8, 1.0, and 1.2%) to ensure the instrument stabilized and was able to reach thermal equilibrium. We removed the data during the periods where there were operational difficulties, setup, or maintenance. This data was collected for ARM Field Campaign AFC07055 and supported by DOE ASR grant DE-SC0021047. For any further questions, please feel free to contact the instrument PI, Sarah D. Brooks, sbrooks@tamu.edu. Rose et. al. Calibration and Measurement Uncertainties of a Continuous-Flow Cloud Condensation Nuclei Counter (DMT-CCNC): CCN Activation of Ammonium Sulfate and Sodium Chloride Aerosol Particles in Theory and Experiment. Atmos. Chem. Phys., 8, 1153-1179, 2008. Deng et. al. Using Raman Microspectroscopy to Determine Chemical Composition and Mixing State of Airborne Marine Aerosols over the Pacific Ocean. Aerosol Science and Technology, Vol 48, Issue 2, 2014. Kesten et. al. Calibration of a TSI Model 3025 Ultrafine Condensation Particle Counter. Aerosol Science and Technology, 15:2, 107-111, 1991. Gormley et. al. Diffusion from a Stream Flowing through a Cylindrical Tube. Proceedings of the Royal Irish Academy, Vol 52, 163-169, 1948. Aerosol Measurement: Principles, Techniques, and Applications, Third Edition. John Wiley & Sons, Inc, 2011. Crane et. al. Inertial Deposition of Particles in a Bent Pipe. Journal of Aerosol Science, Vol 8, 161-170, 1977. Dirgo et. al. Cyclone Collection Efficiency: Comparison of Experimental Results with Theoretical Predictions. Aerosol Science and Technology, 4:4, 401-415, 1985.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

The SILEX experiment system operations

The European Space Agency is going to conduct an inter orbit link experiment which will connect a low Earth orbiting satellite and a Geostationary satellite via optical terminals. This experiment has been called SILEX (Semiconductor Inter satellite Link EXperiment). Two payloads will be built. One called PASTEL (PASsager de TELecommunication) will be embarked on the French Earth observation satellite SPOT4. The future European experimental data relay satellite ARTEMIS (Advanced Relay and TEchnology MISsion) will carry the OPALE terminal (Optical PAyload Experiment). The principal characteristic of the mission is a 50 Megabits flow of data transmitted via the optical satellite link. The relay satellite will route the data via its feeder link thus permitting a real time reception in the European region of images taken by the observation satellite. The PASTEL terminal has been designed to cover up to 9 communication sessions per day with an average of 5. The number of daily contact opportunities with the low earth orbiting satellite will be increased and the duration will be much longer than the traditional passes over a ground station. The terminals have an autonomy of 24 hours with respect to ground control. Each terminal will contain its own orbit model and that of its counter terminal for orbit prediction and for precise computation of pointing direction. Due to the very narrow field of view of the communication laser beam, the orbit propagation calculation needs to be done with a very high accuracy. The European Space Agency is responsible for the operation of both terminals. A PASTEL Mission Control System (PMCS) is being developed to control the PASTEL terminal on board SPOT4. The PMCS will interface with the SPOT4 Control Centre for the execution of the PASTEL operations. The PMCS will also interface with the ARTEMIS Mission Control System for the planning and the coordination of the operation. It is the first time that laser technology will be used to support inter-satellite links in Europe. Due to the complexity and experimental character of this new optical technology, the SILEX experiment control facilities will be designed to allow as much operational flexibility as possible.

Demelenne, B.↗
NASA NTRS1994

EUVE Guest Observer Program Handbook: Extreme Ultraviolet Explorer Guest Observer Documentation: Use with Addendum 1 for 1995 - Appendix G

The Extreme Ultraviolet Explorer (EUVE) is a NASA explorer-class satellite mission devoted entirely to observations in the wavelength range from 70 to 760 Angstroms. The science payload incorporates five separate instruments: four photometric imaging systems and a three-channel EUV spectrometer. During the first phase of the mission, the imaging instruments were used to conduct a complete sky survey in four different bands in the EUV. The survey results are available to the scientific community in the first EUVE sky survey bright source list and the first EUVE all-sky catalog. The second part of the mission is being conducted by NASA as a Guest Observer program, for which pointed spectroscopic observations are conducted for guest scientists under proposals submitted to NASA and supported by the EUVE Guest Observer Center at Berkeley. The mission lifetime will extend through at least a third year of observations. Further extensions of the EUVE mission will be partially contingent upon a review process conducted in September of 1994. To support an extended mission, please contact the chair of the EUVE User 's Committee1 or the EUVE Project Office (address below). The EUVE Guest Observer (EGO) Program is supported by the EUVE Guest Observer Center (EGO Center) at the Center for Extreme Ultraviolet Astrophysics (CEA), at the University of California, Berkeley. The policies of the EGO Program and specified in the NRA. This Handbook is produced by the EGO Center as a guide to choosing appropriate targets for observation and preparing proposals. The rest of this chapter gives a broad overview of the EUVE mission and the EGO Center.

EUVE↗
DOE OSTI2022

Gamma Spectrometry Code Rodeo for Uranium Enrichment—FY 2021 Report

In FY22, the participating Department of Energy (DOE) laboratories continued the work on the project “Gamma Spectrometry Code Rodeo for Uranium Enrichment”. Oak Ridge National Laboratory (ORNL) and Lawrence Livermore National Laboratory (LLNL) continued their efforts to acquire spectra using uranium sources. A collimator (with side and back shields) was custom designed and constructed at ORNL. Spectra were acquired at ORNL using the uranium enrichment standards supplied by New Brunswick Laboratory (NBL) and the collimated M400 detector. Spectra were also acquired using steel absorbers of different thickness placed between the source and the collimated M400 detector. The plan was to ship the collimator to LLNL so that spectra could be acquired using the LLNL detector in collimated geometries. This activity was suspended since problems were noticed with the performance of the LLNL M400 detector. Also, it was brought to light to the project team that some of the aspects of the M400 detector had been updated by the vendor H3D in response to requests by the IAEA. In February 2021, the ORNL and LLNL M400 detectors were returned to the H3D factory in order to resolve the problems with the LLNL detector and to update ORNL and LLNL detectors to the same configuration as the M400 supplied to the IAEA. H3D repaired the LLNL M400 and performed the IAEA updates on both the ORNL and LLNL detectors. ORNL and LLNL received the detectors in April 2021. Data acquisition was continued using the upgraded detectors. ORNL re-collected the spectra using point sources and the NBL standards in uncollimated and collimated geometries. The collimator was shipped from ORNL to LLNL. Spectra were acquired at LLNL through Q4 of FY22. When the ORNL spectra were examined closely, it became apparent that there were spurious artifacts present in some of the spectra. This rendered suspect the ORNL spectra collected in June/July 2021 time frame. ORNL contacted H3D and per H3D’s advice, the M400 detector was returned to H3D for repairs in mid-August 2021. H3D diagnosed the problem and established that the root cause was the extra tight packaging that created a strain on the CZT crystals, causing one of them to break down. The repaired M400 was returned to ORNL in early September 2021. ORNL re-started data acquisition for the third time. Data was continued to be acquired at ORNL and LLNL through September 2021. The ORNL and LLNL data will be shared with the principal investigators from the analyzing laboratories. The GADRAS code and FRAM have been developed to have the capability to analyze the M400 spectra. Good quality spectra from FY21 have been analyzed using modified versions of GADRAS and FRAM. The spectra have also been analyzed using the GEM code. The analysis results from GADRAS, FRAM and GEM codes are presented and discussed in this report. Some preliminary results from FRAM and GEM analysis were presented in February 2021 at the U-Pu Isotopics Workshop sponsored by the IAEA. CZTU code is being modified to analyze M400 spectra. Data collection, code development and analysis will be continued in FY22 as per the FY22 Project Work Plan (PWP).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1975

Advances in the theory and application of BSF cells

The characteristics and behavior of p(+), p solar cells were investigated. The p(+), p cells were made by the removal of the n(+) surface layers from n(+), p p(+), BSF cells followed by application of a suitable contact to the resultant p(+), p structures. The open circuit voltage of p(+), p cells was found to increase with increasing 'p' bulk resistivity. The measured open circuit velocity-temperature coefficients were positive and increased with increasing resistivity. An outline of prior limitations in solar cell design is presented, and the removal of these limitations through use of BSF effects is pointed out. The study of BSF effects made feasible production of very thin high efficiency silicon cells as well as high resistivity-high efficiency cells, two desirable types of silicon cells which were previously impossible to make.

Mandelkorn, J.↗
NASA NTRS1989

X-ray beam method for displacement measurement in hostile environments

A new method of extensometry using an X-ray beam was devised, and the results of current testing reveal it to be highly feasible. This technique has been shown to provide a non-contacting system that is immune to problems associated with density variations in gaseous environments, that plague currently available optical methods. This advantage is a result of the non-refracting penetrating nature of X-rays. The method is based on X-ray-induced X-ray fluorescence of targets, which subsequently serve as fudicial markers. Some target materials have melting points over 1600 degrees C which will facilitate measurement at extremely high temperatures. A highly focused intense X-ray beam, which is produced using a Johansen 'bent crystal', is then scanned across the target, which responds by fluorescing X-rays when stimulated by the incident beam. This secondary radiation is monitored using a detector. By carefully measuring beam orientation, change in target edge position can be determined. Many variations on this basic theme are now possible such as two targets demarcating a gage length, or a beam shadowing method using opaque targets.

Jordan, Eric H.↗
NASA NTRS2002

Contact Analog/Compressed Symbology Heading Tape Assessment

A simulation assessed the performance, handling qualities and workload associated with a contact-analog, world-referenced heading tape as implemented on the Comanche Helmet Integrated Display Sight System (HIDSS) when compared with a screen-fixed, compressed heading tape. Six pilots, four active duty Army Aviators and two civilians flew three ADS-33 maneuvers and a traffic pattern in the Ames Vertical Motion Simulation facility. Small, but statistically significant advantages were found for the compressed symbology for handling qualities, workload, and some of the performance measures. It should be noted however that the level of performance and handling qualities for both symbology sets fell within the acceptable tolerance levels. Both symbology sets yield satisfactory handling qualities and performance in velocity stabilization mode and adequate handling qualities in the automatic flight control mode. Pilot comments about the contact analog symbology highlighted the lack of useful rate of change information in the heading tape and "blurring" due to the rapid movement of the heading tape. These issues warrant further study. Care must be taken in interpreting the operational significance of these results. The symbology sets yielded categorically similar data, i.e., acceptable handling qualities and adequate performance, so while the results point to the need for further study, their operational significance has yet to be determined.

Shively, R. Jay↗
DOE OSTI2022

Fluid – Fluid Interfacial Area and Its Impact on Relative Permeability - A Pore Network Modeling Study

Abstract Relative permeability (kr) is commonly modeled as an empirical function of phase saturation. Although current empirical models can provide a good match of one or two measured relative permeabilities using saturation alone, they are unable to predict relative permeabilities well when there is hysteresis or when physical properties such as wettability change. Further, current models often result in relative permeability discontinuities that can cause convergence and accuracy problems in simulation. To overcome these problems, recent research has modeled relative permeability as a state function of both saturation (S) and phase connectivity (X). Pore network modeling (PNM) data, however, shows small differences in relative permeability for the same S-X value when approached from a different flow direction. This paper examines the impact of one additional Minkowski parameter (Mecke and Arns, 2005), the fluid-fluid interfacial area, on relative permeability to identify if that satisfactorily explains this discrepancy. We calculate the total fluid-fluid interfacial areas (IA) during two-phase (oil/water) flow in porous media using pore network modeling. The area is calculated from PNM simulations using the areas associated with corners and throats in pore elements of different shapes. The pore network is modeled after a Bentheimer sandstone, using square, triangular, and circular pore shapes. Simulations were conducted for numerous primary drainage and imbibition cycles at a constant contact angle of 0° for the wetting phase. Simultaneous measurements of capillary pressure, relative permeability, saturation, and phase connectivity are made for each displacement. Fluid-fluid interfacial area is calculated from the PNM capillary pressure, the fluid location in the pore elements, and the pore element dimensional data. The results show that differences in the relative permeability at the same (S,X) point is explained well by differences in the fluid-fluid interfacial area (IA). That is, for a larger change in IA at these intersection points, the permeability difference is greater. That difference in relative permeability approaches zero as the difference in IA approaches zero. This confirms that relative permeability can be modeled better as a unique function of S, X, and IA. The results also show that an increase in IA restricts flow decreasing the nonwetting (oil) phase permeability. This decrease is caused by an increase in the throat area fraction compared to the corner area as the total area IA increases. The wetting phase relative permeability, however, shows the inverse trend, in that its relative permeability is greater when IA becomes larger owing to a greater fraction of the total area associated with the corners. The area IA, however, impacts the nonwetting phase relative permeability more than the wetting phase relative permeability. Corner flow improves the wetting phase relative permeability because the wetting phase is continuous there. Finally, a sensitivity analysis shows that relative permeability a is more sensitive to change in S than they are for IA for the case studied implying that if only two parameters are used to model relative permeability it is better to choose S and X.

Engineering↗
NASA NTRS1990

Tele-Autonomous control involving contact

Object localization and its application in tele-autonomous systems are studied. Two object localization algorithms are presented together with the methods of extracting several important types of object features. The first algorithm is based on line-segment to line-segment matching. Line range sensors are used to extract line-segment features from an object. The extracted features are matched to corresponding model features to compute the location of the object. The inputs of the second algorithm are not limited only to the line features. Featured points (point to point matching) and featured unit direction vectors (vector to vector matching) can also be used as the inputs of the algorithm, and there is no upper limit on the number of the features inputed. The algorithm will allow the use of redundant features to find a better solution. The algorithm uses dual number quaternions to represent the position and orientation of an object and uses the least squares optimization method to find an optimal solution for the object's location. The advantage of using this representation is that the method solves for the location estimation by minimizing a single cost function associated with the sum of the orientation and position errors and thus has a better performance on the estimation, both in accuracy and speed, than that of other similar algorithms. The difficulties when the operator is controlling a remote robot to perform manipulation tasks are also discussed. The main problems facing the operator are time delays on the signal transmission and the uncertainties of the remote environment. How object localization techniques can be used together with other techniques such as predictor display and time desynchronization to help to overcome these difficulties are then discussed.

Shao, Lejun↗
NASA NTRS2006

Simplified Optics and Controls for Laser Communications

A document discusses an architecture of a spaceborne laser communication system that provides for a simplified control subsystem that stabilizes the line of sight in a desired direction. Heretofore, a typical design for a spaceborne laser communication system has called for a high-bandwidth control loop, a steering mirror and associated optics, and a fast steering-mirror actuator to stabilize the line of sight in the presence of vibrations. In the present architecture, the need for this fast steering-mirror subsystem is eliminated by mounting the laser-communication optics on a disturbance-free platform (DFP) that suppresses coupling of vibrations to the optics by 60 dB. Taking advantage of microgravitation, in the DFP, the optical assembly is free-flying relative to the rest of the spacecraft, and a low-spring-constant pointing control subsystem exerts small forces to regulate the position and orientation of the optics via voice coils. All steering is effected via the DFP, which can be controlled in all six degrees of freedom relative to the spacecraft. A second control loop, closed around a position sensor and the spacecraft attitude-control system, moves the spacecraft as needed to prevent mechanical contact with the optical assembly.

Chen, Chien-Chung↗
DOE OSTI2024

Carbon Management Projects (CONNECT) Database and Explorer

Overview The Carbon Management Projects (CONNECT) Toolkit is an online exploratory visualization tool developed by the U.S. Department of Energy's (DOE) Office of Fossil Energy and Carbon Management (FECM) with support from other federal agencies such as the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Transportation (DOT). It provides a single point of access to authoritative information on federal agency investment in a portfolio of research, development, and demonstration (RD&D) projects that have been publicly announced to advance technologies for point source carbon capture, carbon dioxide removal, transport, storage, and conversion, collectively referred to as carbon management. The RD&D programs covered in this tool are authorized by annual congressional appropriations ("Base Program") and the 2021 Infrastructure Investment and Jobs Act (IIJA). The tool also incorporates public information on other federal initiatives, such as the Regional Clean Hydrogen Hubs, and public information released by other government agencies, such as the Environmental Protection Agency's (EPA) and Primacy States’ Underground Injection Control Class VI permits and EPA’s facility level greenhouse gas (GHG) emissions. Developed in a geographic information system, the tool organizes carbon management projects into five groups based on the primary technology that a project aims to advance, each visually represented as a digital layer ("carbon management project layer"). Only federally funded projects are included, which can be awarded projects that are completed or ongoing, or projects that have been selected but are currently under negotiation. Project information can be viewed in the map or in the attribute table below it when turned on. In the map view, each project is displayed at either its host site (for field work), where available, or its performer site (project lead's location, further explained in the table below). Host sites and performer sites are represented in distinct icons. Several reference layers offer additional public information on infrastructural and natural resource environment for carbon management. These reference layers, combined with multiple geographical basemaps, enable users to visualize the carbon management project layers in context. Carbon management project information will be updated monthly based on feedback and information availability. Carbon management project layers Point Source Carbon Capture (PSC) This layer contains DOE-funded projects focused on capturing carbon dioxide (CO2) from power plants or industrial facilities. Carbon Dioxide Removal (CDR) This layer contains DOE-funded projects focused on capturing CO2 from the atmosphere, including direct air capture (DAC) and DAC hubs, direct ocean capture, enhanced mineralization, and biomass carbon removal and storage. For projects with multiple host sites, each of the sites are displayed individually with the project cost and cost sharing information representing the total for the entire project. Carbon Transport This layer contains DOE- and DOT-funded projects focused on CO2 transport. The Transport Research and Development sublayer contains projects that do not involve physical infrastructure; the Proposed Transport Corridor sublayer contains projects for which either a route for the transport infrastructure has been proposed or a general area for the transport infrastructure has been identified. Carbon Storage This layer contains DOE-funded key projects focused on CO2 storage. For projects with multiple field-work sites, each of the sites are displayed individually on the map with the project cost and cost sharing information representing the overall total for the entire project. Carbon Conversion This layer contains DOE-funded projects focused on converting CO2 into economically valuable products. Reference layers The following layers provide additional information in the geographic proximity of carbon management projects. Users should reference the original sources for more details (weblinks provided below and in pop-up windows on the map). Regional Clean Hydrogen Hub and Facility These layers illustrate the approximate areas of the Regional Clean Hydrogen Hubs announced by DOE's Office of Clean Energy Demonstrations (OCED) and the approximate locations of individual facilities that constitute the hubs (see "Where are the H2Hubs located?" on the webpage linked above). EPA Facility Level GHG Emissions (direct emitter) This layer shows direct CO2 emissions from stationary sources in 2022, using data extracted from EPA's Facility Level Information on GreenHouse gases Tool (FLIGHT). Captured and injected CO2 are not deducted from direct emitters’ total emissions. Contact EPA for additional details. Underground Injection Control Class VI permit/permit application This layer shows the locations of CO2 injection wells that are granted or in the process of applying for an Underground Injection Control Class VI permit by EPA or a Primacy State (currently Louisiana, North Dakota, and Wyoming). The URLs for the permits or permit applications are provided in the pop-up windows associated with the well locations. Contact EPA for additional details. Carbon Storage Resource This layer contains information on prospective CO2 storage resources in saline formations and oil and gas reservoirs provided by the National Carbon Sequestration Database and Geographic Information System (NATCARB) spatial database. Contact NETL for additional details. Existing CO2 pipeline This layer shows active CO2 pipelines based on information digitized from the map issued by the Pipeline and Hazardous Materials Safety Administration (PHMSA). Contact PHMSA for additional details.

Carbon Conversion↗
DOE OSTI2024

Discrete-Element and Material-Point Method (DEM and MPM) Based Solvers for Sustainable Technologies

We present the use of discrete element method (DEM) and material point method (MPM) in three relevant green technology applications that include biomass feedstock handling, lithium-ion battery manufacturing, and high-pressure reverse osmosis. Our open-source DEM and MPM solvers are developed using performance portable grid and particle management library, AMReX, thus enabling superior performance on NVIDIA and AMD GPUs with > 100 million particles. Our DEM solver resolves the motion of individual particles in a granular system and includes a bonded sphere method for modeling non-spherical particles along with Hertzian and liquid bridge-based contact models. We simulate highly variable biomass feedstock flows in large-scale hoppers for biofuel production and electrode calendering in battery manufacturing using DEM. Our simulations predict flow blockage in large scale biomass hoppers and electrode microstructure variations, thus providing valuable information for biofuel and battery manufacturers, respectively. The second half of the talk will be on MPM and its application towards pore resolved simulations of reverse osmosis membranes under compressive loads. We present a validation study of our MPM simulations with membrane microscopy imaging thus providing useful insights on membrane stability under high pressure conditions. We also present a spectral stability analysis of using linear hat, quadratic and cubic spline basis in MPM indicating regions of numerical stability.

BIOMASS FUELS,MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Interactions involved in the adsorption of ethylene glycol and 2-hydroxyethoxide on the Au(111) surface: a Density Functional Theory study

Abstract Context:The monolayers of ethylene glycol and 2-hydroxyethoxide on gold surfaces have been used in hybrid materials as biosensors. In this article, the adsorption of ethylene glycol and 2-hydroxyethoxide on the Au(111) surface was analyzed. For the first system, ethylene glycol on Au(111), there are Au$$\cdot \cdot \cdot $$ · · · O and Au$$\cdot \cdot \cdot $$ · · · H interactions. To the best of our knowledge, the Au$$\cdot \cdot \cdot $$ · · · H interaction has been overlooked until now. However, in this work, there is strong evidence that this interaction is important to stabilize the system. For the second system, the atomic interactions mentioned previously are also predicted, although there is an additional interaction between 2-hydroxyethoxide molecules. Such an interaction induces the link -O-H-O-, with high values of the electron density at the critical points of the corresponding bond path of the O-H interaction. These links suggest the forming of ethylene glycol chains.Methods:The calculations were performed using two exchange-correlation functionals: BEEF-vdW and C09$$_{x}$$ x -vdW; both functionals incorporate dispersion effects within the Kohn-Sham approach in Density Functional Theory as implemented in GPAW code and ASE computational packages. The contacts between the molecules considered in this article and the Au(111) surface were analyzed through the Quantum Theory of Atoms in Molecules implemented in GPUAM code.

Biochemistry & Molecular Biology↗
NASA NTRS1986

Titan Probe navigation analysis

In the proposed Cassini mission, a combined Saturn Orbiter/Titan Probe spacecraft will be launched from the Space Shuttle to arrive at Saturn around 2002, by means of a delta-VEGA trajectory. After Saturn-orbit insertion and a pericrone raise maneuver, the probe will be released to enter the Titan atmosphere and impact onto its surface. During its descent phase and impact onto Titan, the probe will maintain radio contact with the orbiter. Since the Titan-probe experimental phase lasts for only about four hours, probe-orbiter geometry and probe-delivery accuracy are critical to successful completion of this part of the mission. From a preliminary navigation analysis for probe delivery accuracy, it seems feasible to deliver the probe within 50 km (1-sigma value) of the desired aim-point in the Titan B-plane. The covariance study, however, clearly indicates the need for optical data, in addition to radio metric data. A Monte Carlo study indicates that a Delta-V capability of 98 m/sec for trajectory correction maneuvers will be sufficient to cover 99 percent of all contingencies during the segment from Saturn-orbit insertion to Titan-probe release.

Vijayaraghavan, A.↗