Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixed effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Photorefractive effect in CdMnTe:V Crystal

We present two-wave mixing result obtained with a CdMnTe:V crystal. A photorefractive gain coefficient of 0.20 /cm was observed at 633 nm with the signal-to-pump ratio being of the order of 10(exp -3). This crystal was grown by vertical Bridgman Technique and doped with Vanadium during the growth. The crystal were of good optical quality and showed high resistivity. Room temperature absorption and low temperature photoluminescence studies comparing the band edge and defect center at the doped and undoped CdMnTe crystal will also be discussed.

Pour, K. M.↗
NASA NTRS2003

Effects of Humidity on Aerosols in Southern Africa during the Biomass Burning Season

Measurements of the aerosol total light scattering coefficient, asp, and the aerosol hemispheric backscatter ratio, p(1), as functions of relative humidity (RH in %) (so-called humidographs) at three wavelengths (450,550, and 700 nm) were obtained in the dry season in southern Africa (1) in ambient air in South Africa, Botswana, Mozambique and Zambia, (2) at various distances downwind in identifiable smoke plumes from biomass fires, and (3) along the southwest coast of Africa. The ratio of sigma(sub sp) at an RH of 80% to that at 30% provides a measure of the effects of RH on sigma(sub sp), and similarly for Beta(1). For the three broad sampling categories given above, and at a wavelength of 550 nm, these ratios varied from 1.42 +/- 0.05 to 2.07 +/- 0.03 for sigma(sub sp), and from 0.69 +/- 0.05 to 0.99 +/- 0.14 for Beta(1). In general, humidographs for the ambient air samples showed a greater dependence on RH than those for smoke from identifiable biomass fires. During a period when dense, aged smoke was transported to the region from the north, the humidographs for sigma(sub sp) for ambient air samples were similar to those for identifiable smoke plume samples just approximately 10- to 50-min old. This suggests that as far as the effects of RH on sigma(sub sp) are concerned the effects of aging of smoke and its mixing with ambient air are realized within less than about an hour.

Magi, Brian I.↗
NASA NTRS2006

Line Mixing in Water Vapor and Methane

A multispectrum fitting algorithm has been used to identify line mixing and determine mixing parameters for infrared transitions of H2O and CH4 in the 5-9 micrometer region. Line mixing parameters at room temperature were determined for two pairs of transitions in the v2 fundamental band of H2O-16, for self-broadening and for broadening by H2, He, CO2, N2, O2 and air. Line mixing parameters have been determined from air-broadened CH4 spectra, recorded at temperatures between 210 K and 314 K, in selected R-branch manifolds of the v4 band. For both H2O and CH4, the inclusion of line mixing was seen to have a greater effect on the retrieved values of the line shifts than on the retrieved values of other parameters

Smith, M. A. H.↗
NASA NTRS2010

High-Resolution Spectroscopy of Stratospheric Ethane Following the Jupiter Impact of 2009

We report on high-resolution infrared spectroscopy of ethane (C2H6) performed at the latitude of an impact site on Jupiter discovered on 19 July 2009 by A. Wesley from a location in Murrumbateman, Australia. The observations used the NASA Goddard Space Flight Center's Heterodyne Instrument for Planetary Wind and Composition (HIPWAC) at the NASA Infrared Telescope Facility (IRTF) on Mauna Kea, Hawaii. HIPWAC is a mid-infrared (9-12 microns) heterodyne spectrometer operating at the highest limit of spectral resolving power (lambda\Delta\lambda > l06), providing information on atmospheric constituent abundance and temperature through fully resolved tine shapes. Ethane is a stable trace product of methane photochemistry that is nearly uniformly mixed in Jupiter's stratosphere, providing an effective probe of that altitude region. Ethane emission line profiles near 11,74 microns in the Ug band were measured in Jupiter's stratosphere at 25 MHz (11.00083/cm) resolution. A sequence of spectra of ethane acquired over a range of longitude at the impact latitude (56S planetocentric) probes constituent abundance and temperature profile, both on and off the impact region. Near the site of the impact, ethane emission increased above levels measured well outside the impact region. Radiative transfer analysis indicates increased ethane mole fraction (30% greater). Variation in the measured continuum level and line intensities within 75deg of the impact longitude indicate the presence of an opacity source (haze) at altitudes near and above the tropopause and as high as the 10-mbar level near the impact site. The indication of possible haze opacity up to the 10-mbar level in the atmosphere is consistent with measurements made by HIPWAC's predecessor as part of the IRTF Shoemaker Levy-9 campaign in 1994.

Fast, Kelly↗
NASA NTRS2010

Detailed Structure of the Tropical Upper Troposphere and Lower Stratosphere as Revealed by Balloon Sonde Observations of Water Vapor, Ozone, Temperature, and Winds During the NASA TCSP and TC4 Campaigns

We report on balloon sonde measurements of water vapor and ozone using the cryogenic frost point hygrometer and electrochemical concentration cell ozonesondes made at Alajuela, Costa Rica (10.0 N, 84.2 W) during two NASA airborne campaigns: the Tropical Convective Systems and Processes (TCSP) mission in July 2005 and the Tropical Composition, Clouds, and Climate Coupling Experiment (TC4), July - August 2007. In both campaigns we found an upper troposphere that was frequently supersaturated but no evidence that deep convection had reached the tropopause. The balloon sondes were complemented by campaigns of 4 times daily high-resolution radiosondes from mid-June through mid-August in both years. The radiosonde data reveal vertically propagating equatorial waves that caused a large increase in the variability of temperature in the tropical tropopause layer (TTL). These waves episodically produced cold point tropopauses (CPTs) above 18 km, yet in neither campaign was saturation observed above approx 380 K or 17 km. The averages of the water vapor minima below this level were 5.2 ppmv in TCSP and 4.8 ppmv in TC4, and the individual profile minima all lay at or above approx 360 K. The average minima in this 360 C380 K layer provide a better estimate of the effective stratospheric entry value than the average mixing ratio at the CPT. We refer to this upper portion of the TTL as the tropopause saturation layer and consider it to be the locus of the final dehydration of nascent stratospheric air. As such, it is the local equivalent to the tape head of the water vapor tape recorder.

Selkirk, Henry B.↗
NASA NTRS2015

Benefits of a 4th Ice Class in the Simulated Radar Reflectivities of Convective Systems Using a Bulk Microphysics Scheme

Numerous cloud microphysical schemes designed for cloud and mesoscale models are currently in use, ranging from simple bulk to multi-moment, multi-class to explicit bin schemes. This study details the benefits of adding a 4th ice class (hail) to an already improved 3-class ice bulk microphysics scheme developed for the Goddard Cumulus Ensemble model based on Rutledge and Hobbs (1983,1984). Besides the addition and modification of several hail processes from Lin et al. (1983), further modifications were made to the 3-ice processes, including allowing greater ice super saturation and mitigating spurious evaporationsublimation in the saturation adjustment scheme, allowing graupelhail to become snow via vapor growth and hail to become graupel via riming, and the inclusion of a rain evaporation correction and vapor diffusivity factor. The improved 3-ice snowgraupel size-mapping schemes were adjusted to be more stable at higher mixing rations and to increase the aggregation effect for snow. A snow density mapping was also added. The new scheme was applied to an intense continental squall line and a weaker, loosely-organized continental case using three different hail intercepts. Peak simulated reflectivities agree well with radar for both the intense and weaker case and were better than earlier 3-ice versions when using a moderate and large intercept for hail, respectively. Simulated reflectivity distributions versus height were also improved versus radar in both cases compared to earlier 3-ice versions. The bin-based rain evaporation correction affected the squall line case more but did not change the overall agreement in reflectivity distributions.

bulk microphysics schemes↗
NASA NTRS2015

Parametric Design of Injectors for LDI-3 Combustors

Application of a partially calibrated National Combustion Code (NCC) for providing guidance in the design of the 3rd generation of the Lean-Direct Injection (LDI) multi-element combustion configuration (LDI-3) is summarized. NCC was used to perform non-reacting and two-phase reacting flow computations on several LDI-3 injector configurations in a single-element and a five-element injector array. All computations were performed with a consistent approach for mesh-generation, turbulence, spray simulations, ignition and chemical kinetics-modeling. Both qualitative and quantitative assessment of the computed flowfield characteristics of the several design options led to selection of an optimal injector LDI- 3 design that met all the requirements including effective area, aerodynamics and fuel-air mixing criteria. Computed LDI-3 emissions (namely, NOx, CO and UHC) will be compared with the prior generation LDI- 2 combustor experimental data at relevant engine cycle conditions.

injectors↗
NASA NTRS2016

CFD-Based Design of a Filming Injector for N+3 Combustors

An effort was undertaken to perform CFD analysis of fluid flow in Lean-Direct Injection (LDI) combustors with axial swirl-venturi elements coupled with a new fuel-filming injector design for next-generation N+3 combustors. The National Combustion Code (NCC) was used to perform non-reacting and two-phase reacting flow computations on a N+3 injector configuration, in a single-element and a five-element injector array. All computations were performed with a consistent approach towards mesh-generation, spray-, ignition- and kinetics-modeling with the NCC. Computational predictions of the aerodynamics of the injector were used to arrive at an optimal injector design that met effective area, aerodynamics, and fuel-air mixing criteria. LDI-3 emissions (EINOx, EICO and UHC) were compared with the previous generation LDI-2 combustor experimental data at representative engine cycle conditions.

combustion chambers↗
NASA NTRSDate not supplied

Trajectory Planning for Mission Survivability of Autonomous Vehicles in Moderately to Extremely Uncertain Environments

Trajectory planning is a particularly challenging task for autonomous vehicles when the uncertainties in their operating environment cannot be characterized statistically. In this paper, we propose a receding horizon control strategy with novel trajectory planning policies that enable dynamic updating of the planned trajectories of autonomous vehicles operating in environments where potential conflicts are, from a statistical perspective, either partially known or completely unknown. The proposed policies utilize two metrics: (1) the number of feasible trajectories; and (2) the robustness of the feasible trajectories. We measure the effectiveness of the suggested policies in terms of mission survivability, which is defined as the probability that the primary mission is accomplished or, if that is not possible, the vehicle lands safely at an alternative site. We show that a linear combination of both metrics is an effective objective function when there is a mix of partially known and unknown uncertainties. When the operating environment is dominated by unknown disturbances, maximizing the number of feasible trajectories results in the highest mission survivability. These findings have significant implications for achieving safe aviation. autonomy.

Aviation autonomy↗
NASA NTRSDate not supplied

Trajectory Planning for Mission Survivability of Autonomous Vehicles in Moderately to Extremely Uncertain Environments

Trajectory planning is a particularly challenging task for autonomous vehicles when there are moderate to extreme uncertainties in their operating environment, i.e., where the trajectories of hazards are partially known to completely unknown. In this paper, we propose a receding horizon control strategy with novel trajectory planning policies that enable dynamic updating of the planned trajectories of autonomous vehicles. The proposed policies utilize two metrics: (1) the number of feasible trajectories; and (2) the robustness of the feasible trajectories. We measure the effectiveness of the suggested policies in terms of mission survivability, which is defined as the probability that the primary mission is accomplished or, if that is not possible, the vehicle lands safely at an alternative site. We show that a linear combination of both metrics is an effective objective function when there is a mix of partially known and unknown uncertainties. When the operating environment is dominated by unknown disturbances, maximizing the number of feasible trajectories results in the highest mission survivability. These findings have significant implications for achieving safe aviation autonomy.

aviation autonomy↗
NASA NTRS2023

Modulation of the Seasonal Cycle of the Antarctic Sea Ice Extent By Sea Ice Processes and Feedbacks With the Ocean and the Atmosphere

The seasonal cycle of the Antarctic sea ice extent is strongly asymmetric, with a relatively slow increase after the summer minimum followed by a more rapid decrease after the winter maximum. This cycle is intimately linked to the seasonal cycle of the insolation received at the top of the atmosphere, but sea ice processes as well as the exchanges with the atmosphere and ocean may also play a role. To quantify these contributions, a series of idealized sensitivity experiments have been performed with an eddy-permitting (∘) NEMO-LIM3 (Nucleus for European Modelling of the Ocean–Louvain-la-Neuve sea ice model version 3) Southern Ocean configuration, including a representation of ice shelf cavities, in which the model was either driven by an atmospheric reanalysis or coupled to the COSMO-CLM2 regional atmospheric model. In those experiments, sea ice thermodynamics and dynamics as well as the exchanges with the ocean and atmosphere are strongly perturbed. This perturbation is achieved by modifying snow and ice thermal conductivities, the vertical mixing in the ocean top layers, the effect of freshwater uptake and release upon sea ice growth and melt, ice dynamics, and surface albedo. We find that the evolution of sea ice extent during the ice advance season is largely independent of the direct effect of the perturbation and appears thus mainly controlled by initial state in summer and subsequent insolation changes. In contrast, the melting rate varies strongly between the experiments during the retreat, in particular if the surface albedo or sea ice transport are modified, demonstrating a strong contribution of those elements to the evolution of ice coverage through spring and summer. As with the advance phase, the retreat is also influenced by conditions at the beginning of the melt season in September. Atmospheric feedbacks enhance the model winter ice extent response to any of the perturbed processes, and the enhancement is strongest when the albedo is modified. The response of sea ice volume and extent to changes in entrainment of subsurface warm waters to the ocean surface is also greatly amplified by the coupling with the atmosphere.

regional atmosphere ocean sea ice model↗
NASA NTRS2023

Importance of Atmospheric Feedbacks in Simulating the Seasonal Cycle of the Antarctic Sea Ice and Its Response to Perturbations

The seasonal cycle of the Antarctic sea ice extent is largely controlled by the evolution of the insolation received at the top of the atmosphere. However, sea ice processes and feedbacks with the ocean and the atmosphere can modulate this seasonal cycle. Here, the atmospheric feedbacks are quantified in a series of idealized sensitivity experiments performed with an eddy-permitting (1/4°) NEMO-LIM3 Southern Ocean configuration, including a representation of ice shelf cavities, in which the model was either driven by an atmospheric reanalysis or coupled to the COSMO-CLM 2 regional atmospheric model. In these experiments, sea ice thermodynamics and dynamics as well as the exchanges with the ocean and atmosphere are strongly perturbed. This perturbation is achieved by modifying snow and ice thermal conductivities, the vertical mixing in the ocean top layers, the effect of freshwater uptake/release upon sea ice growth/melt, ice dynamics and surface albedo. We show that the changes in surface heat fluxes are very different between the configurations driven by the reanalysis and those coupled to the atmosphere. Atmospheric feedbacks enhance the response of the modelled winter ice extent to any of the perturbed processes, and the enhancement is strongest when the albedo is modified. The response of sea ice volume and extent to changes in entrainment of subsurface warm waters to the ocean surface is also greatly amplified by the coupling with the atmosphere. By contrast, the atmospheric feedbacks can damp the impact of the perturbations affecting the heat conductivity through sea ice.

Atmospheric feedbacks↗
NASA NTRS1975

Shear-flexible finite-element models of laminated composite plates and shells

Several finite-element models are applied to the linear static, stability, and vibration analysis of laminated composite plates and shells. The study is based on linear shallow-shell theory, with the effects of shear deformation, anisotropic material behavior, and bending-extensional coupling included. Both stiffness (displacement) and mixed finite-element models are considered. Discussion is focused on the effects of shear deformation and anisotropic material behavior on the accuracy and convergence of different finite-element models. Numerical studies are presented which show the effects of increasing the order of the approximating polynomials, adding internal degrees of freedom, and using derivatives of generalized displacements as nodal parameters.

Noor, A. K.↗
NASA NTRS1980

Effectiveness of advanced fuel-conservative procedures in the transitional ATC environment

The real time simulation (involving both the pilot and the air traffic controller) of fuel conservative approaches, profile descents, and four dimensional area navigation to assess the effectiveness of the procedures is discussed. Generally, results indicate some difficulties with the procedures tested in a mixed traffic environment and point to the need for computer assistance for effective implementation of candidate procedures.

Tobias, L.↗
NASA NTRS1993

Turbulent mixing layers in the interstellar medium of galaxies

We propose that turbulent mixing layers are common in the interstellar medium (ISM). Injection of kinetic energy into the ISM by supernovae and stellar winds, in combination with density and temperature inhomogeneities, results in shear flows. Such flows will become turbulent due to the high Reynolds number (low viscosity) of the ISM plasma. These turbulent boundary layers will be particularly interesting where the shear flow occurs at boundaries of hot (approximately 10(exp 6) K) and cold or warm (10(exp 2) - 10(exp 4) K) gas. Mixing will occur in such layers producing intermediate-temperature gas at T is approximately equal to 10(exp 5.0) - 10(exp 5.5) that radiates strongly in the optical, ultraviolet, and EUV. We have modeled these layers under the assumptions of rapid mixing down to the atomic level and steady flow. By including the effects of non-equilibrium ionization and self-photoionization of the gas as it cools after mixing, we predict the intensities of numerous optical, infrared, and ultraviolet emission lines, as well as absorption column densities of C 4, N 5, Si 4, and O 6.

Slavin, J. D.↗
NASA NTRS1995

Some wave-particle effects on large-scale Alfven wave propagation and damping

Phase mixing can reduce greatly the torsional Alfven wave's dissipation length for propagation in complex magnetic field-line geometries. This phase mixing causes significant energy transfers from large to small scales where a conversion from ordered wave energy into a particle kinetic form occurs. This conversion during its initial stages is an entropy conserving process well described by Vlasov theory, Nonlinear stages of wave-particle resonance, particle trapping, and collisional resistivity are often invoked as processes eventually responsible for converting ordered wave motions into random thermal motion. Strictly speaking, this entropy producing phase cannot be described within Vlasov theory, and the large-scale effects of these microscopic events resides at the difficult frontier between generalized fluid and kinetic theories. We attempt to describe certain aspects of such resonances within the framework of fluid theory focusing on torsional Alfven wave energy transport and deposition within flux tubes.

Siregar, E.↗
NASA NTRS2004

Possible NASA Contributions to HEAT

A four-year experiment (HEAT) has been proposed (one summer in the field, 2005) to determine the sources and causes for the enhanced cloud-to-ground lightning over Houston, Texas, in association with simultaneous experiments by the Environmental Protection Agency (EPA) and the Texas Natural Resource Conservation Commission (TNRCC). Houston is the third most populous city in the United States and the region contains 50% of the petroleum refining capacity of the United States. Recent studies covering the period 1989-2000 document a 50% increase of cloud-to-ground lightning in the Houston area as compared to background values, which is second in flash density only to the Tampa Bay, Florida area. It is suggested that the elevated flash densities could result from several factors, including, 1) the convergence due to the urban heat island effect and complex sea breeze, and 2) the increasing levels of air pollution from anthropogenic sources producing numerous small droplets and thereby suppressing mean droplet size. The latter effect would enable more cloud water to reach the mixed phase region where it is involved in the formation of precipitation and the separation of electric charge, leading to an enhancement of lightning. The primary goals of HEAT are to examine the effects of (1) pollution, (2) the urban heat island, and (3) the complex coastline, on storms and lightning characteristics in the Houston area. The project is a multi- agency effort and will employ numerous observing capabilities and expertise. Dr. Shepherd has been asked to serve as a possible co- investigator to contribute expertise in areas related to urban impacts on precipitation variability. Dr. Shepherd is also a key NASA representative in the interagency effort. This presentation will provide an overview of recent NASA research focused on urban rainfall in Houston and offer potential NASA capabilities that could contribute to HEAT.

Shepherd, J. M.↗
NASA NTRS1979

Ammonia photolysis and the greenhouse effect in the primordial atmosphere of the earth

Photochemical calculations indicate that in the prebiotic atmosphere of earth ammonia would have been irreversibly converted to N2 in less than 40 years if the ammonia surface mixing ratio were no more than 0.0001. However, if a continuous outgassing of ammonia were maintained, radiative-equilibrium calculations indicate that a surface mixing ratio of ammonia of 0.0001 or greater would provide a sufficient greenhouse effect to keep the surface temperature above freezing. With a 0.0001 mixing ratio of ammonia, 60% to 70% of the present-day solar luminosity would be adequate to maintain surface temperatures above freezing. A lower limit to the time constant for accumulation of an amount of nitrogen equivalent to the present day value is 10 my if the outgassing were such as to provide a continuous surface mixing ratio of ammonia of at least 0.00001.

Kuhn, W. R.↗