SEARCH · Engineering Papers

Results for “injection rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

All sources NASA NTRS DOE OSTI

DOE OSTI2023

On the confluence of ultrafast high-temperature sintering and flash sintering phenomena

Ultrafast high-temperature sintering (UHS) and flash sintering are novel methods for rapid sintering of ceramics, often completed in just a few seconds. Here, we show that both also share two additional features: an abrupt rise in electrical conductivity, which is electronic, and electroluminescence. More fundamentally, both are related to phonon physics where MD calculations have shown that proliferation of phonons at the edge of the Brillouin zone can induce Frenkel pairs without the application of electrical fields. Here, we show that, indeed, heating without the application of electric field, can also induce flash: Rapid heating processes of thin films of an oxide-salt deposited on silk fibers, with a propane torch, are shown to induce electronic conductivity, electroluminescence, and rapid sintering of the oxide. Further, the discussion in this article harkens back to two inventions, more than a century ago, which can now be related to flash and UHS: (i) the Nernst glow lamp circa 1900, made from zirconia, and (ii) the Welsbach mantle, constituted from ceria doped thorium oxide, in the late nineteenth century. Thus, the confluence between high heating rate and electric field induced flash phenomena links the past to the new. The emerging question is how injection of phonons that has been shown to create Frenkels can further induce high electronic conductivity and electroluminescence in oxides. Both electronic conductivity and luminescence are likely related to the generation of electron–hole pairs.

36 MATERIALS SCIENCE↗

NASA NTRS1972

Artificial perturbations of the radiation belts

A review is given of the properties of the radiation belts which have been produced by high-altitude nuclear detonations. The low-yield, Argus devices, 1, 2, and 3, and the Soviet test of 1 November 1962 injected intense electron fluxes in narrow L-shell intervals, with peaks at L = 1.72, 2.11, 2.17, and 1.77, respectively. The energy spectra of the electrons were indistinguishable from the equilibrium fission beta spectrum, and the fluxes initially decayed at rates approximately proportional to (time) sup -1.1. The high-yield devices, Starfish and the Soviet tests of 22 October and 28 October 1962, injected electrons over wide ranges. At L values near the lower boundary, the electron spectra appeared to be softer at the higher L values.

Cladis, J. B.↗

NASA NTRS1972

The aerothermodynamic environment of the Apollo command module during superorbital entry

Aerothermodynamic measurements were obtained on two Apollo spacecraft during atmospheric entry at near-lunar-return velocities. Histories of measured pressure and of convective and radiative heating rates are compared with theoretical predictions and with wind-tunnel results. The comparisons show that pressures measured in the wind tunnel correspond to those measured in the flight environment of the entry face. Unexplained low pressures were obtained on the conical section. Measured radiative heating rates agree with predictions calculated for both visible and infrared radiation. Good agreement was found between convective heating rates measured in flight and predictions obtained by using cold wall theory adjusted for mass injection from the ablator.

Lee, D. B.↗

NASA NTRS1981

Structure of impulsive phase of solar flares from microwave observations

Variation of the microwave intensity and spectrum due to gyro-synchrotron radiation from semi-relativistic particles injected at the top of a closed magnetic loop is described. Using the recent high spatial resolution X-ray observations from the HXIS experiment of Solar Maximum Mission and from observations by the Very Large Array (VLA), it is shown that the high microwave brightness observed at the top of the flare loop can come about if (1) the magnetic field from top to footpoints of the loop does not increase very rapidly, and (2) the accelerated particles injected in the loop have a nearly isotropic pitch angle distribution. The limits on the rate of increase of the magnetic field and/or the average pitch angle depend on the geometry and location of the loop on the solar disk.

Petrosian, V.↗

NASA NTRS1982

Structure of the impulsive phase of solar flares from microwave observations

Variation of the microwave intensity and spectrum due to synchrotron radiation from semirelativistic particles injected at the top of a closed magnetic loop has been described. Using the recent high spatial resolution X-ray observations from the HXIS experiment of the SMM and observations by the VLA, it is shown that the high microwave brightness observed at the top of the flare loop can come about if (1) the magnetic field from top to footpoints of the loop does not increase very rapidly, and (2) the accelerated particles injected in the loop have a nearly isotropic pitch angle distribution. The limits on the rate of increase of the magnetic field or the average pitch angle depend on the geometry and location of the loop on the solar disk.

Petrosian, V.↗

NASA NTRS1987

Combustion chamber heat transfer characterization of LOX/hydrocarbon-type propellants

The gas-side heat transfer rates for LOX/propane and LOX/ethanol are experimentally characterized using a 1000 lb thrust water-cooled calorimeter chamber. The effects of injector element type and fuel film cooling are defined as a function of mixture ratio. The interaction of fuel injected through the resonator cavities on heat transfer and wall soot buildup are displayed as a function of time, axial distance, fuel coolant flow rate, and mixture ratio. Comparisons between clean-burning ethanol and sooting propane show a large difference between the two fuels and significantly higher than expected heat flux levels for ethanol in the throat region.

Schoenman, Leonard↗

NASA NTRS1989

Motivating the sure bounds

Motivation is provided for a theorem that provides upper and lower bounds for the reliability of reconfigurable digital control systems. The reliability goals for these systems are too high to be established by natural life testing, which means the probability of system failure must be computed from mathematical models that capture the essential elements of fault occurence and system fault recovery. The upper and lower bound theorem shows that system recovery can be adequately described by its first two moments, provided component failure rate is low and system recovery is fast. This result greatly simplifies both the fault injection experiments that study system recovery and the numerical computations that estimate the probability of system failure from a mathematical model.

White, Allan L.↗

NASA NTRS1989

Fuel-air mixing and distribution in a direct-injection stratified-charge rotary engine

A three-dimensional model for flows and combustion in reciprocating and rotary engines is applied to a direct-injection stratified-charge rotary engine to identify the main parameters that control its burning rate. It is concluded that the orientation of the six sprays of the main injector with respect to the air stream is important to enhance vaporization and the production of flammable mixture. In particular, no spray should be in the wake of any other spray. It was predicted that if such a condition is respected, the indicated efficiency would increase by some 6 percent at higher loads and 2 percent at lower loads. The computations led to the design of a new injector tip that has since yielded slightly better efficiency gains than predicted.

Abraham, J.↗

NASA NTRS1992

Rocket plume flowfield characterization using laser Rayleigh scattering

A Doppler-resolved laser Rayleigh scattering diagnostic was applied to a 111 N thrust, regenerative and fuel-film cooled, gaseous hydrogen/gaseous oxygen rocket engine. The axial and radial mean gas velocities were measured from the net Doppler shifts observed for two different scattering angles. Translational temperatures and number densities were estimated from the Doppler widths and scattered intensities, respectively, by assuming that water was the dominant scattering species in the exhaust. The experimental results are compared with theoretical predictions from a full Navier-Stokes code (RD/RPLUS) and the JANNAF Two-Dimensional Kinetics (TDK) and Standardized Plume Flowfield (SPF-II) codes. Discrepancies between the measured and predicted axial velocities, temperatures, and number densities are evident. Radial velocity measurements, however, show excellent agreement with predictions. The discrepancies are attributed primarily to inefficient mixing and combustion caused by the injection of excessive oxidizer along one side of the thrust chamber. Thrust and mass flow rate estimates obtained from the Rayleigh measurements show excellent agreement with the globally measured values.

Zupanc, Frank J.↗

NASA NTRS1992

Rocket plume flowfield characterization using laser Rayleigh scattering

Zupanc, Frank J.↗

NASA NTRS1947

Investigation of Thrust Augmentation of a 1600-pound Thrust Centrifugal-flow-type Turbojet Engine by Injection of Refrigerants at Compressor Inlets

Investigations were conducted to determine effectiveness of refrigerants in increasing thrust of turbojet engines. Mixtures of water an alcohol were injected for a range of total flows up to 2.2 lb/sec. Kerosene was injected into inlets covering a range of injected flows up to approximately 30% of normal engine fuel flow. Injection of 2.0 lb/sec of water alone produced an increase in thrust of 35.8% of rate engine conditions and kerosene produced a negligible increase in thrust. Carbon dioxide increased thrust 23.5 percent.

Jones, William L.↗

NASA NTRS1936

Some Factors Affecting Combustion in an Internal-Combustion Engine

An investigation of the combustion of gasoline, safety, and diesel fuels was made in the NACA combustion apparatus under conditions of temperature that permitted ignition by spark with direct fuel injection, in spite of the compression ratio of 12.7 employed. The influence of such variables as injection advance angle, jacket temperature, engine speed, and spark position was studied. The most pronounced effect was that an increase in the injection advance angle (beyond a certain minimum value) caused a decrease in the extent and rate of combustion. In almost all cases combustion improved with increased temperature. The results show that at low air temperatures the rates of combustion vary with the volatility of the fuel, but that at high temperatures this relationship does not exist and the rates depend to a greater extent on the chemical nature of the fuel.

Rothrock, A M↗

NASA NTRS1995

Global electric field determination in the Earth's outer magnetosphere using energetic charged particles

Although many properties of the Earth's magnetosphere have been measured and quantified in the past 30 years since it was discovered, one fundamental measurement (for zeroth order MHD equilibrium) has been made infrequently and with poor spatial coverage - the global electric field. This oversight is due in part to the neglect of theorists. However, there is renewed interest in the convection electric field because it is now realized to be central to many magnetospheric processes, including the global MHD equilibrium, reconnection rates, Region 2 Birkeland currents, magnetosphere ionosphere coupling, ring current and radiation belt transport, substorm injections, and several acceleration mechanisms. Unfortunately the standard experimental methods have not been able to synthesize a global field (excepting the pioneering work of McIlwain's geostationary models) and we are left with an overly simplistic theoretical field, the Volland-Stern electric field model. Single point measurements of the plasmapause were used to infer the appropriate amplitudes of this model, parameterized by K(sub p). Although this result was never intended to be the definitive electric field model, it has gone nearly unchanged for 20 years. The analysis of current data sets requires a great deal more accuracy than can be provided by the Volland-Stern model. The variability of electric field shielding has not been properly addressed although effects of penetrating magnetospheric electric fields has been seen in mid-and low-latitude ionospheric data sets. The growing interest in substorm dynamics also requires a much better assessment of the electric fields responsible for particle injections. Thus we proposed and developed algorithms for extracting electric fields from particle data taken in the Earth's magnetosphere. As a test of the effectiveness of these new techniques, we analyzed data taken by the AMPTE/CCE spacecraft in equatorial orbit from 1984 to 1989.

Eastman, Timothy E.↗

NASA NTRS1996

Composition and evolution of the atmosphere of Venus

The contract year started by analyzing Jovian atmospheric data acquired by the Galileo Probe Mass Spectrometer (GPMS). Two Venus hydrogen projects got underway as well. The first study strives to understand how to reconcile the standard treatment of the evolution of the H2O and HDO resevoirs on Venus over 4.5 Gyr in the presence of H and D escape and injection by comets. The second study is calculating the charge exchange contribution to hydrogen loss rates, using realistic models for exospheric H, H(+), D, D(+), and ion temperature from PV data. This report includes the following papers as attachments and supporting data: 'The Galileo Probe Mass Spectrometer: Composition of Jupiter's Atmosphere'; 'Chemical Composition Measurements of the Atmosphere of Jupiter with the Galileo Probe Mass Spectrometer'; 'Ion/Neutral Escape of Hydrogen and Deuterium: Evolution of Water'; 'Hydrogen and Deuterium in the Thermosphere of Venus: Solar Cycle Variations and Escape'; and 'Solar Cycle Variations in H(+) and D(+) Densities in the Venus Ionosphere: Implications for Escape'.

Donahue, Thomas↗

NASA NTRS1986

Computational simulation of liquid rocket injector anomalies

A computer model has been developed to analyze the three-dimensional two-phase reactive flows in liquid fueled rocket combustors. The model is designed to study the influence of liquid propellant injection nonuniformities on the flow pattern, combustion and heat transfer within the combustor. The Eulerian-Lagrangian approach for simulating polidisperse spray flow, evaporation and combustion has been used. Full coupling between the phases is accounted for. A nonorthogonal, body fitted coordinate system along with a conservative control volume formulation is employed. The physical models built into the model include a kappa-epsilon turbulence model, a two-step chemical reaction, and the six-flux radiation model. Semiempirical models are used to describe all interphase coupling terms as well as chemical reaction rates. The purpose of this study was to demonstrate an analytical capability to predict the effects of reactant injection nonuniformities (injection anomalies) on combustion and heat transfer within the rocket combustion chamber. The results show promising application of the model to comprehensive modeling of liquid propellant rocket engines.

Przekwas, A. J.↗

DOE OSTI2021

A Physics-Constrained Deep Learning Model for Simulating Multiphase Flow in 3D Heterogeneous Porous Media

Physics-based simulators for multiphase flow in porous media emulate nonlinear processes with coupled physics, and usually require extensive computational resources for software development, maintenance and simulation execution. As a result, a huge demand exists for fast modeling of coupled processes in a wide range of subsurface applications including geological sequestration, hydrocarbon recovery and geothermal energy extraction. In this work, an efficient physics-constrained deep learning model is developed for solving multiphase flow in 3-Dimensional (3D) heterogeneous porous media. The model fully leverages the spatial topology predictive capability of convolutional neural networks, specifically U-Net with successive contracting and expansive steps, and is coupled with an efficient continuity-based smoother to predict flow responses that need spatial continuity. Furthermore, the transient regions are penalized to steer the training process such that the model can accurately capture flow in these regions. The model takes inputs including properties of porous media, fluid properties and well controls, and predicts the temporal-spatial evolution of the state variables (pressure and saturation). While maintaining the continuity of fluid flow, the 3D spatial domain is decomposed into 2D images for reducing training cost, and the decomposition results in an increased number of training data samples and better training efficiency. Additionally, a surrogate model is separately constructed as a postprocessor to calculate well flow rate based on the predictions of state variables from the deep learning model. We use the example of CO 2 injection into saline aquifers, and apply the physics-constrained deep learning model that is trained from physics-based simulation data and emulates the physics process. The model performs prediction with a speedup of ~ 1400 times compared to physics-based simulations, and the average temporal errors of predicted pressure and saturation plumes are 0.27% and 0.099% respectively. Furthermore, water production rate is efficiently predicted by a surrogate model for well flow rate, with a mean error less than 5%. Therefore, with its unique scheme to cope with the fidelity in fluid flow in porous media, the physics-constrained deep learning model can become an efficient predictive model for computationally demanding inverse problems or other coupled processes.

58 GEOSCIENCES↗

NASA NTRS1986

The propagation of solar flare particles in a coronal loop

A time-dependent diffusion equation with velocity-dependent diffusion and energy-loss coefficients was solved for the case where energetic solar particles are injected into a coronal loop and then diffuse out the ends of the loop into the lower corona/chromosphere. The solution yields for the case of relativistic electrons, precipitation rates and populations which are necessary for calculating thick and thin target X-ray emission. It follows that the thick target emission is necessarily delayed with respect to the particle acceleration on injection by more than the mere travel time of the particle over the loop length. In addition the time-dependent electron population at the top of the loop is calculated. This is useful in estimating the resulting micron-wave emission. The results show relative timing differences in the different emission processes which are functions of particle species, energy and the point of injection of the particles into the loop. Equivalent quantities are calculated for non-relativistic protons.

Ryan, J. M.↗

NASA NTRS1936

Some Effects of Injection Advance Angle, Engine-Jacket Temperature, and Speed on Combustion in a Compression-Ignition Engine

An optical indicator and a high-speed motion-picture camera capable of operating at the rate of 2,000 frames per second were used to record simultaneously the pressure development and the flame formation in the combustion chamber of the NACA combustion apparatus. Tests were made at engine speeds of 570 and 1,500 r.p.m. The engine-jacket temperature was varied from 100 degrees to 300 degrees F. And the injection advance angle from 13 degrees after top center to 120 degrees before top center. The results show that the course of the combustion is largely controlled by the temperature and pressure of the air in the chamber from the time the fuel is injected until the time at which combustion starts and by the ignition lag. The conclusion is presented that in a compression-ignition engine with a quiescent combustion chamber the ignition lag should be the longest that can be used without excessive rates of pressure rise; any further shortening of the ignition lag decreased the effective combustion of the engine.

Rothrock, A M↗