Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Topaz, a Potential Volatile-Carrier in Cold Subduction Zone: Constraint from Synchrotron X-ray Diffraction and Raman Spectroscopy at High Temperature and High Pressure

The equation of state and stability of topaz at high-pressure/high-temperature conditions have been investigated by in situ synchrotron X-ray diffraction (XRD) and Raman spectroscopy in this study. No phase transition occurs on topaz over the experimental pressure–temperature ($P-T$) range. The pressure–volume data were fitted by the third-order Birch–Murnaghan equation of state (EoS) with the zero-pressure unit–cell volume V 0 = 343.86 (9) Å 3 , the zero-pressure bulk modulus K 0 = 172 (3) GPa, and its pressure derivative K’ 0 = 1.3 (4), while the obtained K 0 = 155 (2) GPa when fixed K’ 0 = 4. In the pressure range of 0–24.4 GPa, the vibration modes of in-plane bending OH-groups for topaz show non-linear changes with the increase in pressure, while the other vibration modes show linear changes. Moreover, the temperature–volume data were fitted by Fei’s thermal equation with the thermal expansion coefficient α 300 = 1.9 (1) × 10 –5 K –1 at 300 K. Finally, the $P-T$ stability of topaz was studied by a synchrotron-based single-crystal XRD at simultaneously high $P-T$ conditions up to ~10.9 GPa and 700 K, which shows that topaz may maintain a metastable state at depths above 370 km in the upper mantle along the coldest subducting slab geotherm. Thus, topaz may be a potential volatile-carrier in the cold subduction zone. It can carry hydrogen and fluorine elements into the deep upper mantle and further affect the geochemical behavior of the upper mantle.

36 MATERIALS SCIENCE↗

Derived parameters for NGC 6791 from high-metallicity isochrones

We have computed 8, 10, and 12 Gyr isochrones and physically consistent models of zero-age red horizontal branch stars for stellar masses between 0.55 and 1.3 solar mass, all at (fe/H) = +0.15. Comparison to the NGC 6791 BVI photometry of Kaluzny & Udalski (1992) and Montgomery et al. (1994) yields an age of 10.0 +/- 0.5 Gyr at an apparent distance modulus 13.49 less than (m-M)(sub V) less than 13.70. The color offsets required to fit the isochrones, combined with the spectroscopic results of Friel & Janes (1993), imply that the foreground reddening to NGC 6791 lies in the range 0.24 greater than E(B -V) greater than 0.19 with +0.27 less than (Fe/H) less than + 0.44. These results are derived using a technique by which we predict color shifts and apply these to the isochrones to simulate progressively higher metallicities. The zero-age horizontal branch model suggest that the red horizontal branch stars of NGC 6791 have masses approximately less than 0.7 solar mass. The masses are similar to those found for M67 red horizontal branch stars by Tripicco et al. (1993) and for globular cluster red horizontal branch stars, even though the M67 progenitors are approximately 0.2 solar-mass more massive, while the progenitors of globular cluster horizontal branch stars are similarly less massive. This suggests the presence of a mechanism, not strongly dependent on metallicity, which reduces stellar envelopes on the zero-age horizontal branch to a given mass rather than by a given amount.

Dorman, Ben↗

Promising born/graphite/resin composites

Lightweight composite has high specific strength and stiffness and remains effective under extreme environmental conditions. Use as engineering material is feasible because it has excellent mechanical properties and is easily produced within small tolerances on constituent volume fractions. Main benefit of composite is its improved longitudinal strength and modulus.

Evensen, H. A.↗

Nondestructive evaluation of sintered ceramics

Radiography and several acoustic and thermoacoustic microscopy techniques are investigated for application to structural ceramics for advanced heat engines. A comparison is made of the results obtained from the use of scanning acoustic microscopy (SAM), scanning laser acoustic microscopy (SLAM), and thermoacoustic microscopy (TAM). These techniques are evaluated on research samples of green and sintered monolithic silicon nitrides and silicon carbides in the form of modulus-of-rupture (MOR) bars containing deliberately introduced flaws. Strengths and limitations of the techniques are described, with the emphasis being on statistics of detectability of flaws that constitute potential fracture origins. Further, it is shown that radiographic evaluation and guidance helped develop uniform high-density Si3N4 MOR bars with improved four-point flexural strength (875, 544, and 462 MPa at room temperature, 1200 C, 1370 C, respectively) and reduced scatter in bend strength.

Baaklini, George Y.↗

Thermoacoustic Effects at a Solid-Fluid Boundary: The Role of a Second-Order Thermal Expansion Coefficient

Analytical and numerical studies are to be carried out to examine time-averaged thermal effects which are induced by the interaction of strong acoustic fields with a rigid boundary (thermoacoustic streaming). Also of interest is the significance of a second-order thermal expansion coefficient that emerges from this analysis. The model problem to be considered is that of a sphere that is acoustically levitated such that it is effectively isolated in a high-intensity standing acoustic field. The solution technique involves matched asymptotic analysis along with numerical solution of the boundary layer equations. The objective of this study is to predict the thermoacoustic streaming behavior and fully understand the role of the associated second-order thermodynamic modulus.

Gopinath, Ashok↗

Manufacture of porous biodegradable polymer conduits by an extrusion process for guided tissue regeneration

We have fabricated porous, biodegradable tubular conduits for guided tissue regeneration using a combined solvent casting and extrusion technique. The biodegradable polymers used in this study were poly(DL-lactic-co-glycolic acid) (PLGA) and poly(L-lactic acid) (PLLA). A polymer/salt composite was first prepared by a solvent casting process. After drying, the composite was extruded to form a tubular construct. The salt particles in the construct were then leached out leaving a conduit with an open-pore structure. PLGA was studied as a model polymer to analyze the effects of salt weight fraction, salt particle size, and processing temperature on porosity and pore size of the extruded conduits. The porosity and pore size were found to increase with increasing salt weight fraction. Increasing the salt particle size increased the pore diameter but did not affect the porosity. High extrusion temperatures decreased the pore diameter without altering the porosity. Greater decrease in molecular weight was observed for conduits manufactured at higher temperatures. The mechanical properties of both PLGA and PLLA conduits were tested after degradation in vitro for up to 8 weeks. The modulus and failure strength of PLLA conduits were approximately 10 times higher than those of PLGA conduits. Failure strain was similar for both conduits. After degradation for 8 weeks, the molecular weights of the PLGA and PLLA conduits decreased to 38% and 43% of the initial values, respectively. However, both conduits maintained their shape and did not collapse. The PLGA also remained amorphous throughout the time course, while the crystallinity of PLLA increased from 5.2% to 11.5%. The potential of seeding the conduits with cells for transplantation or with biodegradable polymer microparticles for drug delivery was also tested with dyed microspheres. These porous tubular structures hold great promise for the regeneration of tissues which require tubular scaffolds such as peripheral nerve, long bone, intestine, or blood vessel.

NASA Discipline Cell Biology↗

Graphene reinforced UHMWPE fibers

Thermoplastic polymers are increasingly used in electric vehicles, hydrogen fuel cell vehicles, and other decarbonization applications due to their lightweight and formability. Higher-strength polymers are needed to supplant metals in the vehicle structure, thereby reducing mass and improving efficiency. Ultra-high molecular weight polyethylene (UHMWPE) fibers possess one of the highest strength-to-weight ratios of technical polymers, and further improvement via reinforcement by nanofillers, such as graphene, will expand their performance envelope. Here, in this work, UHMWPE/graphene nanocomposite fibers were gel spun and characterized for their morphological, microstructural, thermal, and mechanical properties. The addition of a low fraction of graphene improved the tensile strength of the fibers by 25% and tensile modulus by 32%. Differential scanning calorimetry showed an increase in melting temperature and degree of crystallinity, which indicates improved coordination of the molecular chains induced by the addition of graphene. The reinforcement also affected the cross-sectional shape of the fibers; the aspect ratio of the fibers’ elliptical shape declined with increasing graphene content showing the skeletal effect of the graphene nanofillers in the polymer matrix. The reinforcing effect of graphene declined above a threshold concentration, and theoretical modeling was applied to demonstrate that increased agglomerates led to reduced properties. This work demonstrates a simple, effective method to produce graphene-reinforced UHMWPE fibers and lays a foundation for understanding the potential for leveraging graphene to form ultra-high-performance nanocomposite fibers for myriad engineering applications.

36 MATERIALS SCIENCE↗

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗

Evaluation of a high response electrohydraulic digital control valve

The application is described of a digital control valve on an electrohydraulic servo actuator. The digital control problem is discussed in general as well as the design and evaluation of a breadboard actuator. The evaluation revealed a number of problems associated with matching the valve to a hydraulic load. The problems were related to lost motion resulting from bulk modulus and leakage. These problems were effectively minimized in the breadboard actuator by maintaining a 1000 psi back pressure on the valve circuit and thereby improving the effective bulk modulus.

Anderson, R. L.↗

Evaluation of Common Thermoplastic Polymers in High-Pressure Cycling Hydrogen Under Ambient and Cold Environments as Applicable to the Hydrogen Infrastructure

Thermoplastic polymers are required to perform unfailingly under stringent conditions of changing pressures (35 MPa to 70 MPa) and temperatures (-40°C to +85°C) in storage and fueling operations. Although diffusivity in glassy polymers appear to be an order of magnitude lower than elastomers, polymer microstructural attributes such as degree of crystallinity and presence of polar and non-polar groups on the main chain with and without branching can play a substantial role in influencing their behaviors in hydrogen environments. In the work described here, the effect of high-pressure hydrogen cycling on PEEK, PTFE, PA11, HDPE, POM (and different commercial grades of these polymers) under ambient and cold (-40°C) conditions is addressed. Ex-situ characterization for polymer changes included density measurements for impact of hydrogen retention, hardness changes using nanoindentation, storage modulus and glass transition changes using dynamic mechanical and thermal analysis (DMTA), degree of crystallization with Differential Scanning Calorimetry (DSC) and tensile testing following ASTM D412. In other evaluations, solid-state nuclear magnetic resonance (NMR), attenuated total reflectance Fourier transform infra-red spectroscopy (ATRFTIR), X-ray diffraction (XRD), and X-ray CT results are presented. The overall impact of these evaluations is to establish a technical basis for the behaviors of common thermoplastics in cycling hydrogen environments under ambient and cold temperatures while establishing the relationship between polymer structure-based properties and hydrogen transport effects.

Menon, Nalini C.↗

Lowest critical velocity of rotating shafts.

The effect of the gyroscopic moment on the appearance of a first imaginary critical velocity (minimum negative value of lambda) is investigated and shown to have an important effect on the computation of the first critical velocity. A numerical procedure is developed which can be used for overcoming the difficulties arising when the first real and the first imaginary roots are similar in modulus. As an example, a real shaft with two supports was analyzed. For the computation the real shaft was subdivided into ten sections, and for two of them (representing compressor and turbine) the gyroscopic moment was taken into account. The present method is especially useful when high speed computational facilities are not available.

Atzori, B.↗

Relationship between fatigue life in the creep-fatigue region and stress-strain response

On the basis of mechanical tests and metallographic studies, strainrange partitioned lives were predicted by introducing stress-strain materials parameters into the Universal Slopes Equation. This was the result of correlating fatigue damage mechanisms and deformation mechanisms operating at elevated temperatures on the basis of observed mechanical and microstructural behavior. Correlation between high temperature fatigue and stress strain properties for nickel base superalloys and stainless steel substantiated the method. Parameters which must be evaluated for PP- and CC- life are the maximum stress achievable under entirely plastic and creep conditions respectively and corresponding inelastic strains, and the elastic modulus. For plasticity/creep interaction conditions (PC and CP) two more pairs of stress strain parameters must be ascertained.

Berkovits, A.↗

Detection of an extremely strong magnetic field in the double-degenerate binary merger product HD 144941

HD 144941 is an extreme He (EHe) star, a rare class of subdwarf OB star formed from the merger of two white dwarf (WD) stars. Uniquely amongst EHe stars, its lightcurve has been reported to be modulated entirely by rotation, suggesting the presence of a magnetic field. Here we report the first high-resolution spectropolarimetric observations of HD 144941, in which we detect an extremely strong magnetic field both in circular polarization (with a line-of-sight magnetic field averaged over the stellar disk〈Bz〉 ∼ −8 kG) and in Zeeman splitting of spectral lines (yielding a magnetic modulus of〈B〉 ∼17 kG). We also report for the first time weak Hαemission consistent with an origin an a Centrifugal Magnetosphere (CM). HD 144941’s atmospheric parameters could be consistent with either a subdwarf or a main sequence (MS) star, and its surface abundances are neither similar to other EHe stars nor to He-strong magnetic stars. However, its Hαemission properties can only be reproduced if its mass is around 1 M⊙, indicating that it must be a post-MS object. Since there is no indication of binarity, it is unlikely to be a stripped star, and was therefore most likely produced in a WD merger. HD 144941 is therefore further evidence that mergers area viable pathway for the generation of fossil magnetic fields.

M E Shultz↗

Distributed measurement of minimum and maximum in-situ stress in substrates

A system for performing distributed measurements of in-situ stress includes an expandable element with at least one fiber optic sensor. The expandable element can be positioned at various depths in a hole in a substrate. A pressurizing device expands (and contracts) the expandable element when the expandable element is inserted in the hole in the substrate to exert pressure on the hole wall. A pressure sensor provides a sensor output indicative of a pressure applied to the hole wall by the expandable element. The fiber optic sensor and an optical interrogator measure strain along a length of the sensor in a continuous, high spatial resolution manner Based on the measured strain and pressure sensor output, the system determines various properties of the substrate such as, minimum principal stress, maximum principal stress, and/or principal stress direction associated with one or more fractures in the substrate, as well as substrate modulus.

Ohanian, III, Osgar John↗

High-strength 3D printed poly(lactic acid) composites reinforced by shear-aligned polymer-grafted cellulose nanofibrils

This work demonstrates the application of pilot-scale surface functionalization of cellulose nanofibrils (CNFs) by aqueous grafting-through polymerization and subsequent spray drying in 3D printed poly(lactic acid) (PLA) composites. Grafted-CNF composites attain an ultimate tensile strength of 88 ± 3 MPa and a tensile modulus of elasticity of 7.8 ± 1.3 GPa in the printing direction at 20 wt% reinforcement loading. These increases, 42% and 139% over neat PLA, respectively, represent the strongest reported 3D printed CNF/PLA composite to date in the literature. The mechanisms behind these improvements are investigated by comparisons to neat PLA and unmodified spray-dried CNF/PLA controls using melt rheology, dynamic mechanical analysis, and assessment of the reinforcement dispersion. These experiments reveal that improved network formation and shear-induced alignment of the grafted CNFs facilitate the remarkable tensile properties of the printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-toughness graphite/epoxy composite material experiment

This LDEF experiment was designed to measure the effects of near-earth exposure on graphite/epoxy composites over a range of properties. All of the specimens were 8 plies thick, with one of two different cross-ply angles and with one of four different values of bonding fraction between plies. The mechanical properties of interest are toughness, strength, and elastic modulus. Six toughness specimens and nine strength/modulus specimens were manufactured and flown.

Felbeck, David K.↗

The mechanical behavior of metal-halide perovskites: Elasticity, plasticity, fracture, and creep

Wide ranging mechanical properties — elasticity, plasticity, fracture, and creep — most relevant to the mechanical reliability of perovskite solar cells (PSCs) are systematically investigated. High quality bulk single-crystals of the commonly studied metal-halide perovskites (MHPs) relevant to PSCs are fabricated and studied: CH 3 NH 3 PbBr 3 (MAPbBr 3 ) and CH 3 NH 3 PbI 3 (MAPbI 3 ). The first direct measurement of MHP Young's modulus (E) using uniaxial compression reveals E <100> of 13.1 ± 1.3 and 10.6 ± 1.0 GPa for MAPbBr 3 and MAPbI 3 , respectively. Further, the Vickers micro-hardness H (100) of MAPbBr 3 and MAPbI 3 is 0.54±0.02 GPa and 0.76±0.05 GPa, respectively. The Vickers micro-indentation fracture toughness K IC of MAPbBr 3 and MAPbI 3 is estimated at 0.20±0.03 MPa∙m 0.5 and 0.18±0.03 MPa∙m 0.5 , respectively. The stress-exponent, n, extracted from nanoindentation creep data is ~8 and ~10 for MAPbBr 3 and MAPbI 3 , respectively. The trends in these properties are discussed. These properties are best estimates and are recommended for use in future mechanical behavior and reliability analyses of MHPs and PSCs.

36 MATERIALS SCIENCE↗

Exponential Water Uptake in Ionomer Membranes Results from Polymer Plasticization

Water content is the most influential factor in the performance of ion-exchange membranes (IEMs), controlling their mechanical rigidity, ionic conductivity, and degradation rates. Membranes absorb water exponentially at high water activity (a w ), making that region of the sorption isotherm the most influential on membrane properties. Plasticization of the polymer by water has been proposed to cause this exponential uptake at high a w . However, an integrated microscopic picture of the structure, thermodynamic, and mechanical properties of IEMs as a function of a w has remained elusive. In this work, we use large-scale molecular simulations validated with experimental measurements to compute the sorption isotherms, Young’s modulus, polymer dynamics, and structure of IEMs. The simulations unveil that the exponential increase in water uptake (WU) coincides in all cases with the glass to rubber transition of the membrane, as measured through its Young’s modulus and segmental polymer dynamics. Functionalization of the polymer with alkyl groups further contributes to its plasticization, increasing the WU at a given a w and ion-exchange capacity (IEC). The alkyl chains act synergistically with water to plasticize the polymer matrix and allow water penetration in the membrane. The simulations reveal that the width of the water channels depends on the ratio λ of water to ions in the polymer but is independent of its IEC. We conclude that differences in the polymer matrix–not the water channels–are responsible for the distinct uptake response of IEMs to the thermodynamic driving force of water activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗