Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Testing and analysis of dual-mode adaptive landing gear, taxi mode test system for YF-12A

The effectiveness of a dual mode adaptive landing gear system in reducing the dynamic response of an airplane during ground taxiing was studied. The dynamic taxi tests of the YF-12A research airplane are presented. A digital computer program which simulated the test conditions is discussed. The dual mode system as tested provides dynamic taxi response reductions of 25 percent at the cg and 30 to 45 percent at the cockpit.

Gamon, M. A.↗
NASA NTRS1979

Materials for helicopter gears

Some of the power train transmission gears in helicopter drive systems can become critical components as performance requirements are increased; accordingly, increasing attention must be paid to new alloys in order to obtain required performance reliability and survivability. Candidate advanced alloys, with improved high temperature properties, while increasing the resistance to scoring and scuffing, tend to have lower ductility and fracture toughness. An attempt is made to identify design materials, and process problems and requirements. In addition, it is recommended that the characterization of candidate steels be accelerated; preliminary investigation indicates that new alloys may provide improved capability against surface distress.

Source record↗
NASA NTRS1982

Planar equations of rollout motion for an aircraft with free or steerable landing gears

Equations were derived for an aircraft in a three-point attitude. Transient tire forces were simulated by delaying the application of forces derived from steady-state considerations. Predicted rollout trajectories were similar to those measured in tests of a small-scale landing-gear model equipped with pneumatic tires (where a laterally sloping runway was used to simulate a crosswind), both with and without nose-wheel steering.

Sleeper, R. K.↗
NASA NTRS1982

Tooth profile analysiis of circular-cut, spiral-bevel gears

An analysis of tooth profile changes in the transverse plane of circular-cut, spiral-bevel crown gears is presented. The analysis assumes a straight-line profile in the mid-transverse plane. The profile variation along the centerline is determined by using expressions for the variation of the spiral angle along the tooth centerline, together with the profile description at the mid-transverse plane. It is shown that the tooth surface is a hyperboloid and that significant variations in the pressure angle are possible.

Huston, R. L.↗
NASA NTRS1982

A finite element stress analysis of spur gears including fillet radii and rim thickness effects

Spur gear stress analysis results are presented for a variety of loading conditions, support conditions, fillet radii, and rim thickness. These results are obtained using the SAP IV finite-element code. The maximum stresses, occurring at the root surface, substantially increase with decreasing rim thickness for partially supported rims (that is, with loose-fitting hubs). For fully supported rims (that is, with tight-fitting hubs), the root surface stresses slightly decrease with decreasing rim thickness. The fillet radius is found to have a significant effect upon the maximum stresses at the root surface. These stresses increase with increasing fillet radius. The fillet radius has little effect upon the internal root section stresses.

Chang, S. H.↗
NASA NTRS1982

On finite element stress analysis of spur gears

Spur gear stress analysis results are presented for a variety of loading conditions, support conditions, root radii, and rime thicknesses. These results are obtained using the SAP-IV finite element code. The maximum stresses, occurring at the root surface, substantially increase with decreasing rim thickness for partially supported rims (that is, with loose fitting hubs). For fully supported rims (that is, with tight fitting hubs), the root surface stresses slightly decrease with decreasing rim thickness. The fillet radius has a significant effect upon the maximum stesses at the root surface. These stresses increase with decreasing fillet radius. Finally, the fillet radius has little effect upon the internal root section stresses.

Chang, S. H.↗
NASA NTRS1983

Hybrid geared traction transmissions

The basic configuration of geared traction drives, geometric and structural factors to be considered in their construction, and current work on hybrid helicopter transmissions rated at 500 and 3000 hp are discussed.

Nasvytis, A. L.↗
NASA NTRS1983

Spiral-bevel geometry and gear train precision

A new aproach to the solution of determination of surface principal curvatures and directions is proposed. Direct relationships between the principal curvatures and directions of the tool surface and those of the principal curvatures and directions of generated gear surface are obtained. The principal curvatures and directions of geartooth surface are obtained without using the complicated equations of these surfaces. A general theory of the train kinematical errors exerted by manufacturing and assembly errors is discussed. Two methods for the determination of the train kinematical errors can be worked out: (1) with aid of a computer, and (2) with a approximate method. Results from noise and vibration measurement conducted on a helicopter transmission are used to illustrate the principals contained in the theory of kinematic errors.

Litvin, F. L.↗
NASA NTRS1983

Compliance and stress sensitivity of spur gear teeth

The magnitude and variation of tooth pair compliance with load position affects the dynamics and loading significantly, and the tooth root stressing per load varies significantly with load position. Therefore, the recently developed time history, interactive, closed form solution for the dynamic tooth loads for both low and high contact ratio spur gears was expanded to include improved and simplified methods for calculating the compliance and stress sensitivity for three involute tooth forms as a function of load position. The compliance analysis has an improved fillet/foundation. The stress sensitivity analysis is a modified version of the Heywood method but with an improvement in the magnitude and location of the peak stress in the fillet. These improved compliance and stress sensitivity analyses are presented along with their evaluation using test, finite element, and analytic transformation results, which showed good agreement.

Cornell, R. W.↗
NASA NTRS1983

Application of active control landing gear technology to the A-10 aircraft

Two concepts which reduce the A-10 aircraft's wing/gear interface forces as a result of applying active control technology to the main landing gear are described. In the first concept, referred to as the alternate concept a servovalve in a closed pressure control loop configuration effectively varies the size of the third stage spool valve orifice which is embedded in the strut. This action allows the internal energy in the strut to shunt hydraulic flow around the metering orifice. The command signal to the loop is reference strut pressure which is compared to the measured strut pressure, the difference being the loop error. Thus, the loop effectively varies the spool valve orifice size to maintain the strut pressure, and therefore minimizes the wing/gear interface force referenced.

Ross, I.↗
NASA NTRS1983

Scaled centrifugal compressor, collector and running gear program

The Scaled Centrifugal Compressor, Collector and Running gear Program was conducted in support of an overall NASA strategy to improve small-compressor performance, durability, and reliability while reducing initial and life-cycle costs. Accordingly, Garrett designed and provided a test rig, gearbox coupling, and facility collector for a new NASA facility, and provided a scaled model of an existing, high-performance impeller for evaluation scaling effects on aerodynamic performance and for obtaining other performance data. Test-rig shafting was designed to operate smoothly throughout a speed range up to 60,000 rpm. Pressurized components were designed to operate at pressures up to 300 psia and at temperatures to 1000 F. Nonrotating components were designed to provide a margin-of-safety of 0.05 or greater; rotating components, for a margin-of-safety based on allowable yield and ultimate strengths. Design activities were supported by complete design analysis, and the finished hardware was subjected to check-runs to confirm proper operation. The test rig will support a wide range of compressor tests and evaluations.

Kenehan, J. G.↗
NASA NTRS1983

Lubricant jet flow phenomena in spur and helical gears with modified center distances and/or addendums for out-of-mesh conditions

Out-of-mesh jet lubrication of gears was examined. The pinion impingement cycle was described briefly. An analysis was developed for the lubricant jet flow in the out-of-mesh condition. The analysis provides for the inclusion of modified center distances and modified addendums. Equations were generated for the limit values of variables necessary to remove the severe limitations to facilitate computer analysis. A computer program was designed using these limit formulas to prevent negative impingement (missing) on the pinion.

Akin, L. S.↗
NASA NTRS1983

Proposed solution methodology for the dynamically coupled nonlinear geared rotor mechanics equations

The equations which describe the three-dimensional motion of an unbalanced rigid disk in a shaft system are nonlinear and contain dynamic-coupling terms. Traditionally, investigators have used an order analysis to justify ignoring the nonlinear terms in the equations of motion, producing a set of linear equations. This paper will show that, when gears are included in such a rotor system, the nonlinear dynamic-coupling terms are potentially as large as the linear terms. Because of this, one must attempt to solve the nonlinear rotor mechanics equations. A solution methodology is investigated to obtain approximate steady-state solutions to these equations. As an example of the use of the technique, a simpler set of equations is solved and the results compared to numerical simulations. These equations represent the forced, steady-state response of a spring-supported pendulum. These equations were chosen because they contain the type of nonlinear terms found in the dynamically-coupled nonlinear rotor equations. The numerical simulations indicate this method is reasonably accurate even when the nonlinearities are large.

Mitchell, L. D.↗
NASA NTRS1985

Analysis of Spiral Bevel Gearing

Program generalized for automated finite-element-method model generation. Tedious task of finite-element-method (FEM) model preparation greatly reduced by development of preprocessing program for automated model generation. Utility of program, including ability to rapidly evaluate parametric changes, demonstrated for spiral, helical, and spiral bevel gearing. Postprocessing program also developed, aids in review and interpretation of calculated FEM stresses.

Drago, R. J.↗
NASA NTRS1985

Active control landing gear for ground loads alleviation

An active landing gear has been created by connecting the hydraulic piston in an oleo strut to a hydraulic supply. A controller modulates the pressure in the oleo to achieve the desired dynamic characteristics. Tests on ground rigs (documented by a film) have demonstrated the successful alleviation of induced structural ground loads and the next step will be a flight test using a fighter aircraft.

Mcgehee, J. R.↗