Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “first wall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Cement sensors with acoustic bandgaps using carbon nanotubes

Cement is widely used in wellbores to stabilize the steel casing used in wellbore operations for oil and gas production, enhanced geothermal systems and carbon sequestration, and to limit fluid movement between sub-surface strata. Flaws such as microcracks in wellbore cement can lead to leakage along the wellbore compromising wellbore integrity. There is an increasing need for methods to monitor cement crack propagation in wellbore environments. In this study, we develop and report the first cementitious sensors capable of exhibiting high frequency acoustic bandgaps (ABGs) using carbon nanotubes (CNTs). Computational simulations of a sensor unit cell are used to design cement-multi walled carbon nanotubes (MWCNTs) sensors that show a wide bandgap. When the cement-MWCNTs sensors is embedded in cement specimens, bandgaps were measured experimentally under 300 kHz and under 600 kHz, consistent with the computationally predicted bandgaps in the range of 290–360 kHz, 410–460 kHz and 515–585 kHz. These bandgap features were absent in homogeneous cement specimens. X-ray tomographic reconstructions showed microscopic debonding at cement-MWCNTs sensor interface. Frequency response analysis of a three-dimensional computational model indicated a shift of frequency of minimum transmission due to the interface debonding, but no perturbation of bandgap response was observed. Here, the cement-MWCNTs sensors developed in this study show the potential of a packed CNT inclusion material in cementitious matrix to create ABGs in a cement matrix.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Fluid mechanical model of the acoustic impedance of small orifices

A fluid mechanical model of the acoustic behavior of small orifices is presented which predicts orifice resistance and reactance as a function of incident sound pressure level, frequency, and orifice geometry. Agreement between predicted and measured values is excellent. The model shows the following: (1) The acoustic flow in immediate neighborhood of the orifice can be modeled as a locally spherical flow. Within this near field, the flow is, to a first approximation, unsteady and incompressible. (2) At very low sound pressure levels, the orifice viscous resistance is directly related to the effect of boundary-layer displacement along the walls containing the orifice, and the orifice reactance is directly related to the inertia of the oscillating flow in the neighborhood of the orifice. (3) For large values of the incident acoustic pressure, the impedance is dominated by nonlinear jet-like effects. (4) For low values of the pressure, the resistance and reactance are roughly equal.

Hersh, A. S.↗
NASA NTRS1992

An improved PNS scheme for predicting complex three-dimensional hypersonic flows

Upwinding is incorporated into a numerical technique for predicting hypersonic viscous flows over lifting configurations at moderate angles of attack. A general real-gas flux-vector-splitting technique based on Van Leer's (1982) approach is employed to model upwinding, and three techniques are examined for flux-vector differencing. The three methods are evaluated by applying them to an axisymmetric configuration with a 10-deg afterbody flare. The results indicate that an oscillation-free shock front can be described by using first-order full upwinding across the embedded shock and central-differencing for the other zones. This combined approach is found to be highly convergent for the near-wall region, and its performance is examined for predicting a Mach 15 flow over a finned missile. Attention is given to the effects of gas chemistry which can significantly affect the flows over the missile configurations.

Bhutta, Bilal A.↗
NASA NTRS1993

An experimental study of the sources of fluctuating pressure loads beneath swept shock/boundary-layer interactions

An experimental research program providing basic knowledge and establishing a database on the fluctuating pressure loads produced on aerodynamic surfaces beneath three dimensional shock wave/boundary layer interactions is described. Such loads constitute a fundamental problem of critical concern to future supersonic and hypersonic flight vehicles. A turbulent boundary layer on a flat plate is subjected to interactions with swept planar shock waves generated by sharp fins at angle of attack. Fin angles from 10 to 20 deg at freestream Mach numbers of 3 and 4 produce a variety of interaction strengths from weak to very strong. Miniature Kulite pressure transducers flush-mounted in the flat plate are used to measure interaction-induced wall pressure fluctuations. The distributions of properties of the pressure fluctuations, such as their ring levels, amplitude distributions, and power spectra, are also determined. Measurements were made for the first time in the aft regions of these interactions, revealing fluctuating pressure levels as high as 160 dB. These fluctuations are dominated by low frequency (0-5 kHz) signals. The maximum ring levels in the interactions show an increasing trend with increasing interaction strength. On the other hand, the maximum ring levels in the forward portion of the interactions decrease linearly with increasing interaction sweep back. These ring pressure distributions and spectra are correlated with the features of the interaction flowfield. The unsteadiness of the off-surface flowfield is studied using a new, non-intrusive technique based on the shadow graph method. The results indicate that the entire lambda-shock structure generated by the interaction undergoes relatively low-frequency oscillations. Some regions where particularly strong fluctuations are generated were identified. Fluctuating pressure measurements are also made along the line of symmetry of an axisymmetric jet impinging upon a flat plate at an angle. This flow was chosen as a simple analog to the impinging jet region found in the rear portion of the shock wave/boundary layer interactions under study. It is found that a sharp peak in ring pressure level exists at or near the mean stagnation point. It is suggested that the phenomena responsible for this peak may be active in the swept interactions as well, and may cause the extremely high fluctuating pressures observed in the impinging jet region in the present experimental program.

Settles, G. S.↗
NASA NTRS1993

Reynolds number influences in aeronautics

Reynolds number, a measure of the ratio of inertia to viscous forces, is a fundamental similarity parameter for fluid flows and therefore, would be expected to have a major influence in aerodynamics and aeronautics. Reynolds number influences are generally large, but monatomic, for attached laminar (continuum) flow; however, laminar flows are easily separated, inducing even stronger, non-monatomic, Reynolds number sensitivities. Probably the strongest Reynolds number influences occur in connection with transitional flow behavior. Transition can take place over a tremendous Reynolds number range, from the order of 20 x 10(exp 3) for 2-D free shear layers up to the order of 100 x 10(exp 6) for hypersonic boundary layers. This variability in transition behavior is especially important for complex configurations where various vehicle and flow field elements can undergo transition at various Reynolds numbers, causing often surprising changes in aerodynamics characteristics over wide ranges in Reynolds number. This is further compounded by the vast parameterization associated with transition, in that any parameter which influences mean viscous flow development (e.g., pressure gradient, flow curvature, wall temperature, Mach number, sweep, roughness, flow chemistry, shock interactions, etc.), and incident disturbance fields (acoustics, vorticity, particulates, temperature spottiness, even electro static discharges) can alter transition locations to first order. The usual method of dealing with the transition problem is to trip the flow in the generally lower Reynolds number wind tunnel to simulate the flight turbulent behavior. However, this is not wholly satisfactory as it results in incorrectly scaled viscous region thicknesses and cannot be utilized at all for applications such as turbine blades and helicopter rotors, nacelles, leading edge and nose regions, and High Altitude Long Endurance and hypersonic airbreathers where the transitional flow is an innately critical portion of the problem.

Bushnell, Dennis M.↗
NASA NTRS1992

Toward the optimization of control of unsteady separation

Regardless of our understanding of the complicated physical process, means can always be found to alter the occurrence and development of unsteady separation. To be able to optimize the control of separation, however, requires the identification of the critical aspects to which the intervention may be focused and achieve the desired result with minimum waste of effort. The Lagrangian analysis of unsteady boundary-layer traces the trajectories of individual fluid particles and reveals the 'bad seeds' that, through extreme deformation in the direction normal to the wall, eventually develop into a virtual barrier and cause the ejection of boundary-layer material into the main stream. It follows logically that separation can be triggered or delayed most effectively by targeting these 'bad seeds.' Since they are normally interior points of the boundary layer, attempts to influence them through the boundary conditions are necessarily indirect. Furthermore, as the strategy has to be the modification of the growing process of the 'bad seeds,' whatever may be the intervention scheme, it needs to be strong enough and early enough. In Shen and Wu, examples of how acceleration/deceleration of the two dimensional body, as well as the moving wall of a rotating cylinder, may affect the development of the bad seed toward separation are shown. In fact it was mentioned therein that the results might be the first step for a feasibility study of the control of unsteady separation. Presented are additional results of applying suction to an impulsively started circular cylinder.

Shen, S. F.↗
NASA NTRS1997

Numerical Boundary Conditions for Computational Aeroacoustics Benchmark Problems

Category 1, Problems 1 and 2, Category 2, Problem 2, and Category 3, Problem 2 are solved computationally using the Dispersion-Relation-Preserving (DRP) scheme. All these problems are governed by the linearized Euler equations. The resolution requirements of the DRP scheme for maintaining low numerical dispersion and dissipation as well as accurate wave speeds in solving the linearized Euler equations are now well understood. As long as 8 or more mesh points per wavelength is employed in the numerical computation, high quality results are assured. For the first three categories of benchmark problems, therefore, the real challenge is to develop high quality numerical boundary conditions. For Category 1, Problems 1 and 2, it is the curved wall boundary conditions. For Category 2, Problem 2, it is the internal radiation boundary conditions inside the duct. For Category 3, Problem 2, they are the inflow and outflow boundary conditions upstream and downstream of the blade row. These are the foci of the present investigation. Special nonhomogeneous radiation boundary conditions that generate the incoming disturbances and at the same time allow the outgoing reflected or scattered acoustic disturbances to leave the computation domain without significant reflection are developed. Numerical results based on these boundary conditions are provided.

Tam, Chritsopher K. W.↗
NASA NTRS2001

Reliability Analysis and Reliability-Based Design Optimization of Circular Composite Cylinders Under Axial Compression

This report describes the preliminary results of an investigation on component reliability analysis and reliability-based design optimization of thin-walled circular composite cylinders with average diameter and average length of 15 inches. Structural reliability is based on axial buckling strength of the cylinder. Both Monte Carlo simulation and First Order Reliability Method are considered for reliability analysis with the latter incorporated into the reliability-based structural optimization problem. To improve the efficiency of reliability sensitivity analysis and design optimization solution, the buckling strength of the cylinder is estimated using a second-order response surface model. The sensitivity of the reliability index with respect to the mean and standard deviation of each random variable is calculated and compared. The reliability index is found to be extremely sensitive to the applied load and elastic modulus of the material in the fiber direction. The cylinder diameter was found to have the third highest impact on the reliability index. Also the uncertainty in the applied load, captured by examining different values for its coefficient of variation, is found to have a large influence on cylinder reliability. The optimization problem for minimum weight is solved subject to a design constraint on element reliability index. The methodology, solution procedure and optimization results are included in this report.

Rais-Rohani, Masoud↗
NASA NTRS1989

Vortex generator for flow control

Fluidics flow control of a multiphase supply using a cylindrical chamber is achieved by introducing the supply flow radially into the chamber. The supply flow exits through a port in the center at the chamber. A control fluid is then introduced tangentially about 90.degree. upstream from the supply port. A second control fluid port may be added about 90.degree. upstream from the first control fluid port, but preferably two sets of supply and control ports are added with like ports diametrically opposite each other. The control fluid flows against the circular wall of the control chamber, which introduces a vortex in the flow of the supply flow that decays into a spiral path to the exit port in the center of the chamber. The control flow rate may thus be used to control the spiral path, and therefore the supply flow rate through the exit port.

Collins, Jr., Earl R.↗
NASA NTRS2010

Very Large-Scale Motions in Smooth and Rough Wall Boundary Layers

Structural skeleton of high Reynolds number flow gives insight into smooth and rough walls. (modeling implications not yet clear) Dynamic roughness as a model of "designer" roughness: a) Impose length scale(s) and dominant frequency. b) Irregular roughness well-represented by first "few" POD modes (Christensen, 2009). Experiments and simple model demonstrate: a) Harmonics associated with forcing (and w) important. b) Change to the mean profile (skin friction).

McKeon, Beverley J.↗
NASA NTRS2017

Direct Numerical Simulation of Hypersonic Turbulent Boundary Layer inside an Axisymmetric Nozzle

As a first step toward a study of acoustic disturbance field within a conventional, hypersonic wind tunnel, direct numerical simulations (DNS) of a Mach 6 turbulent boundary layer on the inner wall of a straight axisymmetric nozzle are conducted and the results are compared with those for a flat plate. The DNS results for a nozzle radius to boundary-layer thickness ratio of 5:5 show that the turbulence statistics of the nozzle-wall boundary layer are nearly unaffected by the transverse curvature of the nozzle wall. Before the acoustic waves emanating from different parts of the nozzle surface can interfere with each other and undergo reflections from adjacent portions of the nozzle surface, the rms pressure fluctuation beyond the boundary layer edge increases toward the nozzle axis, apparently due to a focusing effect inside the axisymmetric configuration. Spectral analysis of pressure fluctuations at both the wall and the freestream indicates a similar distribution of energy content for both the nozzle and the flat plate, with the peak of the premultiplied frequency spectrum at a frequency of [(omega)(delta)]/U(sub infinity) approximately 6.0 inside the free stream and at [(omega)(delta)]/U(sub infinity) approximately 2.0 along the wall. The present results provide the basis for follow-on simulations involving reverberation effects inside the nozzle.

Huang, Junji↗
DOE OSTI2025

Heterostructure engineering for wurtzite LaN

Wurtzite LaN (wz-LaN) is a semiconducting nitride with favorable piezoelectric and ferroelectric properties, making it promising for applications in electronics. Here, we use first-principles density functional theory with a hybrid functional to investigate several features that are key for its use in heterostructures. First, for the purposes of growing wz-LaN on a substrate or designing a heterostructure, we show that it can be lattice-matched with a number of cubic materials along their [111] axes. We also evaluate the bound charge at such interfaces, taking into account both the polarization discontinuity and the piezoelectric polarization due to pseudomorphic strain. Second, we investigate band alignments and assess the results for interfaces with zincblende-, rocksalt-, and perovskite-structure compounds, along with chemically similar wurtzite and rocksalt nitrides. Our results provide guidance for the development of electronic devices based on wz-LaN.

36 MATERIALS SCIENCE↗
DOE OSTI2023

First Results from BREAD: Broadband Reflector Experiment for Axion Detection

We report R&D progress, as well as first dark photon search results with BREAD - a novel dish antenna for broadband ~$\mu$eV-eV wave-dark matter detection, which allows to utilize state-of-the-art high-field solenoidal magnets. Axions are converted non-resonantly to photons on a cylindrical metallic wall parallel to an external magnetic field. These photons are then focused using a novel reflector geometry onto a state-of-the-art high-sensitive photon detector. We recently demonstrated [PRL 128 (2022) 131801] that this concept using a $\sim 10\,{\rm m}^2$ conversion area in a $\sim 10\,{\rm T}$ solenoidal magnet has the potential to discover QCD axions spanning multiple decades in mass range. In this talk we discuss progress of our first stage pilot experiments - GigaBREAD and InfraBREAD - covering different mass ranges. We show first results of a room-temperature GigaBREAD prototype and discuss upscaling to larger, cryogenic and magnetized versions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRSDate not supplied

Wall-modeled LES of the NASA Juncture Flow Experiment

We perform wall-modeled large eddy simulation (WMLES) of the NASA Juncture Flow experiment (Kegerise & Neuhart, NASA/TM–2019–20286) using an equilibrium wall model and unstructured finite volume solver, to assess its predictive ability for complex geometries. The flow condition simulated corresponds to 5 degrees angle of attack with a freestream Mach number of 0.189, and a Reynolds number based on the mean crank chord of 2.4 million. All simulations neglect the effects of wind tunnel walls, sting and mast present in the experiment. To assess the performance of WMLES on simpler flows with very coarse grids, we simulate flow in a turbulent channel at a friction Reynolds number, Reτ≈2000, and flow through a square duct at anReτ≈1000. The duct flow results using the equilibrium wall model indicate that the skin friction is inaccurate near the corner for grid topologies and resolutions typically used in WMLES, having implications for more complicated flows such as the juncture flow. For the juncture flow simulation, two different approaches are investigated. The first approach consists of a truncated-domain simulation wherein the inflow plane of the computational domain is placed at≈0.2chord length of the wing, and we prescribe the mean flow from a separate Reynolds-averaged Navier-Stokes (RANS) solution along with synthetic turbulence to initiate realistic unsteadiness in the domain. The second approach involves simulating the entire geometry with trips to trigger transition to turbulence. The truncated- and full-domain simulations contain about 62 and 90 million cells, respectively; with 8-10 points per boundary layer thickness in the wall-parallel directions, 14-20 points in the wall-normal direction and a near-wall viscous spacing (∆n+1) of≈100. Preliminary results are encouraging overall in terms of the prediction of wall pressure, wall skin friction, velocity and stresses; but indicate that further work is required to improve the predictions in the separation bubble and wing-fuselage corner regions. The grid resolution used in this study is still fairly coarse, and the results should be interpreted as work in progress.

Prahladh S Iyer↗
DOE OSTI2025

Electronic and optical properties of transition metal impurities in GaN and AlN

The optical properties of Cr(III) impurities are well studied and exploited in 𝛼−Al 2 ⁢O 3 , which enables ruby lasers. Photoluminescence spectra resembling the famous 1.78 eV emission of Cr in 𝛼−Al 2 ⁢O 3 have been observed in other wide-band-gap host materials, in particular AlN. However, it is unclear whether Cr would produce the same emission in the nitrides as in 𝛼−Al 2 ⁢O 3 , especially given the different local environment (tetrahedral vs octahedral coordination). We investigate the electronic and optical properties of transition metal substitutional impurities (Cr, Co, Ni, and Cu) in wurtzite GaN and AlN from first principles, utilizing hybrid density functional theory. We calculate the optical transition energies using a constrained occupation approach that accounts for the multideterminant nature of the excited states. Our results indicate that substitutional Cr(III) is not responsible for the emission near 1.78 eV observed in the nitrides. Among the examined impurities, only substitutional Co(II) produces emission near 1.78 eV. Based on the favorable properties of Co(II) (low formation energy, small Huang-Rhys factor, and an 𝑆 = 3/2 ground state) we propose it as a promising single-photon emitter or spin qubit. We additionally assign the PL peak observed near 1.05 eV in GaN and AlN to the 2 𝐸→ 4 𝐴 2 transition of the Ni(III) substitution.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Correcting distortions of thin-walled machined parts by machine hammer peening

Thin-walled aerostructural components frequently get distorted after the machining process. Reworking to correct distortions or eventually rejecting parts significantly increases the cost. This paper proposes a new approach to correct distortions in thin-walled components by strategically applying hammer peening on target surfaces of a machined component. Aluminium alloy 7475-T7351 was chosen for this research. The study was divided in two stages. First, the residual stresses (RS) induced by four different pneumatic hammer peening conditions (modifying the stepover distance and initial offset) were characterised in a test coupon, and one of the conditions was selected for the next stage. In the second stage, a FEM model was used to predict distortions caused by machining in a representative workpiece. Then, the RS induced by hammer peening were included in an FEM model to define two hammer peening strategies (varying the coverage area) to analyse the capability to reduce distortions. Two workpieces were machined and then treated with the simulated hammer peening strategies for experimental validation. Results in the test coupon showed that pneumatic hammer peening can generate high compressive RS (-50 to –350 MPa) up to 800 μm depth, with their magnitude increasing with a reduced stepover distance. Application of hammer peening over 4% of the surface of the representative workpiece reduced the machining-induced distortions by 37%, and a coverage area of 100% led to and overcorrection by a factor of five. This confirms that hammer peening can be strategically applied (in target areas and changing the percentage of coverage) to correct low or severe distortions.

42 ENGINEERING↗
DOE OSTI2020

An experimental investigation of flame and autoignition behavior of propane

We report autoignition delay time data are one important means to develop, quantify, and validate fundamental understanding of combustion chemistry at low temperatures (T<1200 K). However, low-temperature chemistry often has higher uncertainties and scatter in the experimental data compared with high-temperature ignition data (T>1200 K). In this study, autoignition properties of propane and oxygen mixtures were investigated using the University of Michigan rapid compression facility in order to understand the effects of ignition regimes on low-temperature ignition data. For the first time for propane, autoignition delay times were determined from pressure histories, and autoignition characteristics were simultaneously recorded using highspeed imaging of the test section through a transparent end-wall. Propane mixtures with fuel-to-O 2 equivalence ratios of φ = 0.25 and φ = 0.5 and O 2 -to-inert gas molar ratios of 1:3.76 were studied over the pressure range of 8.9 to 11.3 atm and the temperature range of 930 – 1070 K. The results showed homogeneous or strong autoignition occurred for all φ = 0.25 experiments, and inhomogeneous or mixed autoignition occurred for all φ = 0.5 experiments. While a limited temperature range is covered in the study, importantly the data span predicted transitions in autoignition behavior, allowing validation of autoignition regime hypotheses. Specifically, the results agree well with strong-autoignition limits proposed based on the Sankaran Criterion. The autoignition delay time data at the strong-ignition conditions are in excellent agreement with predictions using a well-validated detailed reaction mechanism from the literature and a zerodimensional modeling assumption. However, the experimental data at the mixed autoignition conditions were systematically faster than the model predictions, particularly at lower temperatures (T< ~970 K). The results are an important addition to the growing body of data in the literature that show mixed autoignition phenomena are important sources of the higher scatter observed in the low-temperature autoignition data for propane and other fuels. The results are discussed in terms of different methods to capture the effects of pre-autoignition heat release associated with mixed autoignition conditions and thereby address some of the discrepancies between kinetic modeling and experimental measurements.

42 ENGINEERING↗
DOE OSTI2025

Bench-Scale Apparatus for Rapid, Simultaneous, Comprehensive Vapor–Liquid Equilibrium and Kinetic Property Measurements to Advance CO 2 Capture Solvent Technology

We present here, the design, fabrication, and testing of a new "pressure, volume, temperature (PVT)" apparatus that enables rapid standardized testing for viscosity, vapor–liquid equilibria, and kinetics for water-lean carbon capture solvents. This unit is the first of its kind where equilibrium data are collected during operation as a PTx (pressure–temperature–composition) cell while kinetic data are collected simultaneously with an internal mini wetted-wall contactor (WWC) using controlled adjustments of CO 2 injections to allow for measurements of gas flux (in and out of the liquid). Additionally, in situ measurements of viscosity data are also continuously collected while a solvent is in circulation during gas absorption. This cell empowers comprehensive testing of critical CO 2 capture solvent properties in a single measurement, ensuring all data are collected at the same temperature, pressure, and CO 2 loading. This apparatus also expedites screening of materials since less than 50 mL of sample is needed as compared to 2–3 L needed to get similar data from a conventional WWC. In conclusion, we describe here the methodology of data collected on this new PVT cell, nicknamed “Gary” in honor of Professor Gary Rochelle, for multiple water-lean amine solvents, which we compare to data collected from conventional instrumentation for amine testing.

Zheng, Richard [STARS Technology Corporation, Rich↗