Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drops”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Three Dimensional Instantaneous Spray Measurements of Additively Manufactured Candidate Injector Schemes at Varying Pressure Drops

Additively manufactured (AM) injectors have the potential to improve upon the combustion performance achieved using traditionally manufactured (TM) injectors. Traditionally manufactured injector combustion performance decreases greatly in off-design conditions. Additively manufactured injectors hold the potential to sustain high combustion performance over a broader range of operating conditions than currently seen in TM injectors. Additively manufactured injectors promise to offer higher resistances to instability and achieve better overall propellant mixing and atomization for all types of combustion devices. This study expands upon previous studies that used 2-D imaging techniques to characterize the injector spray pattern of candidate AM injector elements. In this study, 3-D instantaneous measurements of the injector spray pattern are taken, allowing for deeper insight into the liquid spray breakup, an inherently 3-D phenomena. Stereo imaging is used for three dimensional analysis, which utilizes two cameras at different angles to reconstruct a three dimensional reconstruction. With this information, AM injectors can be designed to improve propellant mixing and atomization and reduce breakup length. As part of this work, a high-pressure, cold flow experimental spray facility was modified to measure each injector’s spray characteristics in terms of 𝑅𝑒 𝐿 and 𝑊𝑒 𝑔 . This facility is operated to capture instantaneous stereo photographic images, mass flow rates, and injector element thrust for pressure drop across the injector face ranging from 100 to 200 psig at a stiffness ratio of 1.0.

Murphy Mitchell↗
NASA NTRSDate not supplied

Mars Sample Return Earth Entry System Helicopter Drop Test Reconstruction

The Mars Sample Return campaign conducted four successful helicopter drop tests of the Earth Entry System at the Utah Test and Training Range on October, 2023. The tests acquired data for the 52.5 deg sphere cone geometry that can be used to develop models for the terminal descent aerodynamics and flight dynamics used to model ground impact conditions. The acquired test data included both sensor data outputs from an on-board inertial measurement unit, global positioning system, and video cameras as well as atmospheric measurements from weather balloons. This data was processed using a Kalman filter/smoother to reconstruct the capsule’s trajectory and aerodynamics. An equation-error method was used to reconcile the aerodynamics by solving for a set of dispersions in the aerodynamic database that form a best-fit to the reconstructed aerodynamics. The reconstructed trajectories were compared with flight simulations generated using Program to Optimize Simulated Trajectories II. The results indicate that the simulation underpredicted the vehicle oscillation amplitudes. The reconstruction exhibits a persistent low-amplitude oscillation that does not damp out as predicted.

Chris D Karlgaard↗
NASA NTRSDate not supplied

Mars Sample Return Earth Entry System Helicopter Drop Test Reconstruction

The Mars Sample Return campaign conducted four successful helicopter drop tests of the Earth Entry System at the Utah Test and Training Range on October, 2023. The tests acquired data for the 52.5 deg sphere cone geometry that can be used to develop models for the terminal descent aerodynamics and flight dynamics used to model ground impact conditions. The acquired test data included both sensor data outputs from an on-board inertial measurement unit, global positioning system, and video cameras as well as atmospheric measurements from weather balloons. This data was processed using a Kalman filter/smoother to reconstruct the capsule’s trajectory and aerodynamics. An equation-error method was used to reconcile the aerodynamics by solving for a set of dispersions in the aerodynamic database that form a best-fit to the reconstructed aerodynamics. The reconstructed trajectories were compared with flight simulations generated using Program to Optimize Simulated Trajectories II. The results indicate that the simulation underpredicted the vehicle oscillation amplitudes. The reconstruction exhibits a persistent low-amplitude oscillation that does not damp out as predicted.

Chris D Karlgaard↗
DOE OSTI2022

Flash ironmaking drop tube furnace system

A flash ironmaking drop tube furnace includes a primary reaction section having a refractory, an induction coil around the refractory, insulation located between the refractory and the induction coil, and a susceptor located inside the refractory, the susceptor being formed of a material that is heated by induction when electrical current flows through the induction coil, and having at least one interior channel through which particles can pass. The furnace further includes a muffle, located below the primary reaction section; an outer shell surrounding the muffle; at least one heater located adjacent to the muffle; insulation located between the at least one heater and the outer shell; at least one particle feeder that feeds a predetermined volume of particles into the furnace above the primary reaction section; and an inlet port for injecting gas into the furnace, the inlet port being located so that the gas flows through the susceptor and muffle in parallel with the particles.

Green, Edward↗
DOE OSTI2021

Pronghorn Porous Media Model Validation with Pressure Drop Measurements

The verification and validation (V &V) of Pronghorn is imperative to assert its accuracy when predicting the fluid velocity, temperature, and pressure in high temperature gas-cooled reactors. This paper focuses on the validation of the Pronghorn implementation of the incompressible and compressible Navier-Stokes equations using the pressure drop measurements in the engineering-scale pebble bed facility at the Texas A &M university.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2025

A Summary of Results from Vertical Drop Testing of Hybrid III and WIAMan ATDs

With the development and maturation of the Urban Air Mobility (UAM) market, many new types of electric vertical take-off and landing (eVTOL) vehicles will be flying in the national airspace carrying goods, people or conducting operations for a variety of missions. These types of vehicles are unlike current aircraft due to their novel design and operational profile. Several considerations must be examined in areas including noise, comfort and safety in order for these vehicles to be utilized and accepted into the current airspace system. Researchers at NASA Langley Research Center (LaRC) have conducted sub-scale and full-scale tests on representative eVTOL airframes and seats under a variety of dynamic impact conditions. These tests were conducted to generate data necessary to inform the development of standards in the areas specific to crashworthiness of eVTOL vehicle systems and safety. The data in this report relates to occupant responses obtained during a test campaign utilizing various makes, models, and sizes of Anthropomorphic Test Devices (ATD’s, a.k.a. crash test dummies) undergoing vertical impacts in a variety of seats. The data is intended to provide occupant behavior response and injury metrics for several anticipated impact scenarios that may occur in eVTOL operations. This report will present test data highlighting the effects of several variables on the test results. Discussions on the ATD sizes, along with comparisons between different ATD makes and types will be included. The performance of an in-house developed energy absorbing seat will be detailed, and discussions pertaining to the applicability in various loading conditions will be presented. Finally, a discussion as to the applicability of the tested results to eVTOL full-scale conditions will be included.

Dynamic Drop Testing↗
NASA NTRS1961

A Versatile Drop Test Procedure for the Simulation of Impact Environments

In order to assure the reliability of space flight systems and spacecraft, it is necessary to subject these systems, vehicles, and their components to expected shock and impact environmental loads. The Langley Laboratory has found the apparatus and methods discussed in this paper useful in its work along these lines, and feels that other organizations might also find them of value.

Drop test↗