Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cross flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Unsteady motion and transition to turbulence in developing curved duct flow

An experiment was performed to further the understanding of developing flows in curved ducts of square cross-section. Unlike most earlier works, attention was paid to investigating the time-dependent character of the motion. Mean and unsteady flow characteristics were determined using flow visualization and a laser-Doppler velocimeter. Only one velocity component, that aligned in the longitudinal (streamwise) coordinate direction, was measured. Notwithstanding, the time histories, autocorrelations and spectra derived reveal a time-periodic motion that becomes turbulent with increasing Reynolds number. The results are of intrinsic fundamental value and also illustrate the danger of imposing symmetry of the conservation equations on numerical solutions of this flow.

Arnal, M.↗

Two-Phase Quality/Flow Meter

A quality and/or flow meter employs a capacitance probe assembly for measuring the dielectric constant of flow stream, particularly a two-phase flow stream including liquid and gas components.ne dielectric constant of the flow stream varies depending upon the volume ratios of its liquid and gas components, and capacitance measurements can therefore be employed to calculate the quality of the flow, which is defined as the volume ratio of liquid in the flow to the total volume ratio of gas and liquid in the flow. By using two spaced capacitance sensors, and cross-correlating the time varying capacitance values of each, the velocity of the flow stream can also be determined. A microcontroller-based processing circuit is employed to measure the capacitance of the probe sensors.The circuit employs high speed timer and counter circuits to provide a high resolution measurement of the time interval required to charge each capacitor in the probe assembly. In this manner, a high resolution, noise resistant, digital representation of each of capacitance value is obtained without the need for a high resolution A/D converter, or a high frequency oscillator circuit. One embodiment of the probe assembly employs a capacitor with two ground plates which provide symmetry to insure that accurate measurements are made thereby.

Moerk, J. Steven↗

Application of the Method of Coordinate Perturbation to Unsteady Duct Flow

The method of coordinate perturbation is applied to the unsteady flow of a compressible fluid in ducts of variable cross section. Solutions, in the form of perturbation series, are obtained for unsteady flows in ducts for which the logarithmic derivative of area variation with respect to the space coordinate is a function of the 'smallness' parameter of the perturbation series. This technique is applied to the problem of the interaction of a disturbance and a shock wave in a diffuser flow. It is found that, for a special choice of the function describing the disturbance, the path of the shock wave can be expressed in closed form to first order. The method is then applied to the determination of the flow field behind a shock wave moving on a prescribed path in the x,t-plane. Perturbation series solutions for quite general paths are developed. The perturbation series solutions are compared with the more exact solutions obtained by the application of the method of characteristics. The approximate solutions are shown to be in reasonably accurate agreement with the solutions obtained by the method of characteristics.

Himmel, Seymour C.↗

Laminar flow studies of a low-temperature space radiator model using D-shaped tubes

Test results of a low-temperature space radiator model are presented. Radiator performance is evaluated with a low-thermal-conductivity fluid in laminar flow in D-shaped cross-section tubes. The test covered a Reynolds number range from 50 to 4500 and a fluid temperature range from 294 to 414 K (70 to 286 F). For low-temperature radiators, the fluid-to-surface temperature differential was predominately influenced by fluid temperature in laminar flow. Heat transfer and pressure drop for the radiator tube could be predicted within engineering accuracy from existing correlations.

Cintula, T. C.↗

Separation at Crossing Waypoints Under Wind Uncertainty in Urban Air Mobility

To enable high-density operations in major metropolitan areas, urban air mobility networks are anticipated to have air traffic management with higher levels of autonomy. To ensure that this type of autonomy is feasible, one of the critical steps from a safety and efficiency perspective is understanding various factors that affect the spatial separation between airborne flights and ensure that these factors can be managed. In terms of separation assurance and scheduling, an important real-world concern is that future states of aircraft cannot be perfectly predicted. The focus of this research paper is to understand how these prediction errors affect separation and scheduling services and to explore mitigation strategies to handle these errors. In this research, we have simulated these types of uncertainty by adding wind-prediction errors to trajectory predictions for separation. With these wind-prediction errors, we decompose the problem into two separate questions. First, using both simulation and analytical methods, we look at conflict-detection-only scenarios to understand how the wind errors affect required minimum temporal separation between crossing flights to ensure a specific spatial separation. Next, we study how trajectory errors effect conflict resolution, and we explore different combinations of scheduling and separation assurance to mitigate the effects of uncertainty between crossing flights. The conflict resolution algorithm aims to minimize necessary temporal separation between crossing flights under uncertainty, still ensuring safety-critical spatial separation. In summary, this research suggests that the required minimum temporal separation at a crossing waypoint is dependent on factors such as inbound crossing angle, the relative angle between wind direction and bearing of each route, wind magnitude, wind magnitude uncertainty, nominal cruise airspeed of aircraft, and look-ahead time of the conflict detection algorithm. This research also suggests that different combinations of scheduling and separation have different qualitative results. Using a combination of strategic, flow-based scheduling, tactical scheduling at crossings, speed control near crossing points, and separation management leads to a system that is insensitive to trajectory prediction errors with high throughput and flexibility for aircraft away from shared resources.

urban air mobility↗

Separation at Crossing Waypoints Under Wind Uncertainty in Urban Air Mobility

To enable high-density operations in major metropolitan areas, urban air mobility networks are anticipated to have air traffic management with higher levels of autonomy. To ensure that this type of autonomy is feasible, one of the critical steps from a safety and efficiency perspective is understanding various factors that affect the spatial separation between airborne flights and ensure that these factors can be managed. In terms of separation assurance and scheduling, an important real-world concern is that future states of aircraft cannot be perfectly predicted. The focus of this research paper is to understand how these prediction errors affect separation and scheduling services and to explore mitigation strategies to handle these errors. In this research, we have simulated these types of uncertainty by adding wind-prediction errors to trajectory predictions for separation. With these wind-prediction errors, we decompose the problem into two separate questions. First, using both simulation and analytical methods, we look at conflict-detection-only scenarios to understand how the wind errors affect required minimum temporal separation between crossing flights to ensure a specific spatial separation. Next, we study how trajectory errors effect conflict resolution, and we explore different combinations of scheduling and separation assurance to mitigate the effects of uncertainty between crossing flights. The conflict resolution algorithm aims to minimize necessary temporal separation between crossing flights under uncertainty, still ensuring safety-critical spatial separation. In summary, this research suggests that the required minimum temporal separation at a crossing waypoint is dependent on factors such as inbound crossing angle, the relative angle between wind direction and bearing of each route, wind magnitude, wind magnitude uncertainty, nominal cruise airspeed of aircraft, and look-ahead time of the conflict detection algorithm. This research also suggests that different combinations of scheduling and separation have different qualitative results. Using a combination of strategic, flow-based scheduling, tactical scheduling at crossings, speed control near crossing points, and separation management leads to a system that is insensitive to trajectory prediction errors with high throughput and flexibility for aircraft away from shared resources.

urban air mobility↗

Dynamic Characteristics and Stability Analysis of Space Shuttle Main Engine Oxygen Pump

The dynamic characteristics of the Space Shuttle high pressure oxygen pump are presented. Experimental data is presented to show the vibration spectrum and response under actual engine operation and also in spin pit testing for balancing. The oxygen pump appears to be operating near a second critical speed and is sensitive to self excited aerodynamic cross coupling forces in the turbine and pump. An analysis is presented to show the improvement in pump stability by the application of turbulent flow seals, preburner seals, and pump shaft cross sectional modifications.

Gunter, Edgar J.↗

Turbulent flow in a square-to-round transition

Measurements of turbulent flow in a duct with a cross sectional transition from square to round are presented. Laser Doppler velocimetry was used to measure the mean velocity components, turbulence levels and shear stresses. The boundary layers at the inlet and exit of the transition were approximately 13 percent and 20 percent of the hydraulic diameter respectively, becoming thicker near the corner fillets. The development of secondary flow, of magnitudes up to 7 percent of the bulk velocity is shown. This flow is directed away from the corner fillets and along the periphery of the duct and is associated with the longitudinal curvature of the wall and the related pressure gradients.

Taylor, A. M. K. P.↗

A study of the unsteadiness of crossing shock wave turbulent boundary layer interactions

The unsteadiness of crossing shock wave turbulent boundary layer interactions at a nominal Mach number of 3 was examined by measuring wall pressure fluctuations using multiple, high frequency response, pressure transducers. The unsteadiness in the initial part of the interaction for all the interactions is similar to that of single fin interaction as studied by Tran and Bogdonoff (1987). However, for stronger interactions, flow downstream of the inviscid shock crossing position has a significant unsteady characteristic. In this unsteady region of the interaction, mean surface pressure rises significantly over the value obtained from the inviscid shock approximation. The energy spectrum of the fluctuating pressure signal shows a significant increase in the energy level at the higher frequencies.

Poddar, K.↗

An Experiment on the Near Flow Field of the GE/ARL Mixer Ejector Nozzle

This report is a documentation of the results on flowfield surveys for the GE/ARL mixer-ejector nozzle carried out in an open jet facility at NASA Glenn Research Center. The results reported are for cold (unheated) flow without any surrounding co-flowing stream. Distributions of streamwise vorticity as well as turbulent stresses, obtained by hot-wire anemometry, are presented for a low subsonic condition. Pitot probe survey results are presented for nozzle pressure ratios up to 3.5. Flowfields both inside and outside of the ejector are considered. Inside the ejector, the mean velocity distribution exhibits a cellular pattern on the cross sectional plane, originating from the flow through the primary and secondary chutes. With increasing downstream distance an interchange of low velocity regions with adjacent high velocity regions takes place due to the action of the streamwise vortices. At the ejector exit, the velocity distribution is nonuniform at low and high pressure ratios but reasonably uniform at intermediate pressure ratios. The effects of two chevron configurations and a tab configuration on the evolution of the downstream jet are also studied. Compared to the baseline case, minor but noticeable effects are observed on the flowfield.

Zaman, K. B. M. Q.↗

Anomalous Flows at Dayside High-Latitude Magnetopause as Observed by Interball Tail Probe

We analyze magnetopause crossings at high latitudes dayside magnetopause as observed by Interball Tail probe. High time resolution plasma data show strong short-time flows near magnetopause that strongly deviate from surrounding magnetosheath flow. Several quasi- periodic velocity variations are observed at times. Plasma parameters, such as number density, temperature and bulk velocity-of these flows are close to magnetosheath values. These anomalous flows are observed almost at every magnetopause crossing in this region. The ion velocity distributions in these regions indicate the presence of open field lines. Observed properties of these flows suggest their association with reconnection at high latitudes.

Vaisberg, O. L.↗

Analysis of Turbulent Flow and Heat Transfer in Noncircular Passages

Previous work on turbulent heat transfer and flow in tubes was generalized and applied to flow in non-circular passages of equilateral triangular and square cross section. Expressions for eddy diffusivity that had been verified for flow and heat transfer in tubes were assumed to apply in general along lines normal to a wall. Velocity distributions, wall shear-stress distributions, and friction factors, as well as wall heat-transfer distributions, wall temperature distributions, and average heat-transfer coefficients were calculated. In addition, results from a previous analysis for axial flow between rods were compared with new experimental data. For calculating wall temperature distributions, uniform heat generation in the passage wall and uniform heat transfer at the outer surface were assumed. The application of the results is restricted to moderately small peripheral wall temperature variations. Calculations were made for Reynolds numbers from 20,000 to 900,000 and Prandtl numbers from 0.73 to 300. Results show that velocities, shear stresses, and heat transfer in the region near the corner were lower than average values and were zero at the corner. Friction factors and average Nusselt numbers were lower than in a tube.

Taylor, Maynard F.↗

Design and operation of a supersonic annular flow facility

Supersonic annular flow passages exist in propulsion applications that include dual combustion ramjet engines where a supersonic annular flow (the outer flow) mixes with a sonic (or supersonic) gas generator flow (the inner flow) in the shock expansion zone downstream of the gas generator nozzle exit. Other engine designs include components in the form of annular ducts whose cross-sectional area varies in the streamwise flow direction. In some of these configurations, it is necessary to support the outer shroud (cowl) by means of struts positioned between the cowl and centerbody. To investigate the distorting influence of these struts on the local flow structure, it is first necessary to ensure that the intrinsic flow without struts is free of wave reflections and the effects of upstream disturbances. It is also necessary to demonstrate that the intrinsic flow exhibits the characteristics of a well-defined turbulent boundary layer flow, so that changes in the local flow structure induced by the presence of struts can be interpreted properly. The purpose of this Note is to demonstrate that a supersonic flow facility that meets these objectives has been developed.

Williams, K. E.↗

The Effectiveness of a Route Crossing Tool in a Simulated New York Airspace

Congested airspace is the cause of many delays in the terminal area and these delays can have a ripple effect on the rest of a nation's airspace. The New York terminal area is an example of where this happens in the U. S. An important goal, therefore, is to increase the efficiency of operations in congested terminal airspace where possible. Modeling studies of arrival and departure flows have shown that sharing of arrival and departure airspace increases efficiency in terminal operations. One source of inefficiency in terminal operations is that departure aircraft are frequently held level under arrival flows when it would be more efficient to climb the departure aircraft earlier. A Route Crossing Tool was developed to help controllers climb Newark (EWR) departures to the south earlier by temporarily sharing airspace with arrivals coming into LaGuardia (LGA) from the south. Instead of flying under the arrivals, a departure to the south could climb earlier by flying through the arrival airspace if there was a suitable gap between arrivals. A Human-in-the-Loop (HITL) simulation was conducted in this environment which compared three tool conditions: Baseline (no tool), a Single Route Crossing tool in which one route through the arrival flow was evaluated for crossing, and a Multi-Route Crossing tool in which five parallel routes were evaluated. In all conditions, the departures could be held level under the arrival flow. The results showed that controllers climbed a higher proportion of departures in the Multi-Route tool condition than in the other two conditions, with a higher proportion of departures climbed in smaller gaps and in front of trailing arrivals. The controllers indicated that the Multi-Route and Single Route tools helped them estimate distances more accurately and rated safety, workload, and coordination in the simulation as acceptable.

terminal airspace↗

Design and preliminary testing of a Brayton space radiator concept

A low-temperature radiator has been designed to reject 17.62 kW of thermal power from an isotope Brayton power system. This power system has an electrical output of 7.1 kW. The total radiator consists of two radiators connected in series. Both radiators have a redundant coolant loop, shared fins, and are close to flight configuration. A silicone oil is used as the working fluid. Low flow rates and moderate pressure drop in the radiator required a small hydraulic diameter with large heat transfer area and large flow area. To obtain these characteristics and meet schedule limitations, an expanded tube configuration (with an approximately trapezoidal cross section) was selected. Because of the low flow rates and unconventional tube shape, small scale tests were performed to evaluate the validity of existing heat transfer and pressure drop correlations to this case. The results of these tests were in good agreement with predictions.

Miller, T. J.↗

Characterization of the NASA Glenn Research Center 8- by 6-Foot Supersonic Wind Tunnel (2019 Test)

There were several major modifications made to the NASA Glenn Research Center 8- by 6-Foot Supersonic Wind Tunnel between 2016 and 2019, including the 9- by 15-Foot Low Speed Wind Tunnel Acoustic Improvement Modifications. Following completion of these facility modifications, a characterization test was conducted in the 8- by 6-Foot Supersonic Wind Tunnel test section. This test entry collected data for a single test section porosity configuration across the entire operating range of the facility. Flow field data were collected at a cross-sectional plane and axially along test section center-line for use in quantifying the test section flow quality. Off-nominal supersonic conditions were surveyed through variation of balance chamber pressure at each of the discrete flexible wall nozzle settings. Additionally, a baseline check calibration data set was acquired during this entry.

8x6 SWT↗

Comparison of experimental and computational compressible flow in a S-duct

This paper describes experimental measurements of secondary flow in a constant area, circular cross-section 30-30 deg S-duct, and compares the results obtained with the computations performed using the PEPSIG code, a parabolized Navier-Stokes code. The flow entering the duct was turbulent, with entrance Mach number of 0.6, and the boundary layer thickness at the duct entrance was 10 percent of the duct diameter. The duct mean radius of curvature to the duct diameter was 5.077. Flow parameters were measured at six stations along the length of the duct. These measurements were made using a five-port cone probe. At least ten radial traverses were made at each station on both sides of the symmetry plane. Wall static pressures along three azimuth angles of zero, 90, and 180 deg along the duct were measured. Plots presenting the secondary velocity field as well as contour plots of the total and static-pressure fields have been obtained. Strong secondary flows were observed in the first bend, and these continued into the second bend with the formation of new vorticity in the opposite sense in the second bend. The flow exiting the duct contained two pairs of counter-rotating vortices. The computational results are in general agreement with the experiments. However, it appears that the computations underestimate the extent of the pressure distortion, due to simplifications made in the pressure field calculations.

Vakili, A.↗

Refraction of Sound Emitted Near Solid Boundaries from a Sheared Jet

A mathematical model is developed to describe the sound emitted from an arbitrary point within a turbulent flow near solid boundaries. A unidirectional, transversely sheared mean flow is assumed, and the cross-section of the cold jet is of arbitrary shape. The analysis begins with Lilley's formulation of aerodynamic noise and, depending upon the specific model of turbulence used, leads via Fourier analysis to an expression for the spectral density of the intensity of the far-field sound emitted from a unit volume of turbulence. The expressions require solution of a reduced Green's function of Lilley's equation as well as certain moving axis velocity correlations of the turbulence. Integration over the entire flow field is required in order to predict the sound emitted by the complete flow. Calculations are presented for sound emitted from a plugflow jet exiting a semi-infinite flat duct. Polar plots of the far-field directivity show the dependence upon frequency and source position within the duct. Certain model problems are suggested to investigate the effect of duct termination, duct geometry, and mean flow shear upon the far-field sound.

Dill, Loren H.↗