SEARCH · Engineering Papers

Results for “conformance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

All sources NASA NTRS DOE OSTI

NASA NTRS1983

The solar cosmic ray neutron event on June 3, 1982

The observation of solar neutrons from the earth has been reported. The observations were carried out June 3, 1982, following the intense gamma-ray line flare at 1143 UT. The emission spectra of the neutrons was calculated over an energy range from 40 MeV to 1.2 GeV, on the basis of measurements from a gamma-ray/neutron scintillation spectrometer, and the IGY Jungfraujoch neutron monitor at an altitude of 3500 m. Some possible terrestrial effects of the solar neutrons are discussed. It is shown that the calculated spectra conform to the requirement of ion acceleration to GeV energies a few seconds after the start of the impulsive phase of a solar ion flare event.

Debrunner, H.↗

NASA NTRS1984

A unified relation for cavitation erosion

A power-law relationship between the average erosion rate and cumulative erosion is presented. Data analyses from Venturi, magnetostriction, and liquid-impingement devices conform to this unified relation. A normalization technique is also suggested for prediction purposes.

Veerabhadra Rao, P.↗

NASA NTRS1985

A potential-energy surface study of the 2A1 and low-lying dissociative states of the methoxy radical

Accurate, ab initio quantum chemical techniques are applied in the present study of low lying bound and dissociative states of the methoxy radical at C3nu conformations, using a double zeta quality basis set that is augmented with polarization and diffuse functions. Excitation energy estimates are obtained for vertical excitation, vertical deexcitation, and system origin. The rate of methoxy photolysis is estimated to be too small to warrant its inclusion in atmospheric models.

Jackels, C. F.↗

NASA NTRS1985

An explanation for the H Ly-alpha longitudinal asymmetry in the equatorial spectrum of Jupiter - An outcrop of paradoxical energy deposition in the exosphere

An analysis of the Voyager EUV spectra of the Jupiter sunlit equatorial emissions shows no evidence for a substantial dependence of atomic hydrogen abundance on magnetic longitude, required by earlier theories of the H Ly-alpha longitudinal asymmetry. An explanation for the H Ly-alpha bulge phenomenon is advanced in this work that conforms to the observations and does not require a strong asymmetry in atomic hydrogen abundance. It is proposed that the H Ly-alpha bulge is caused by a combination of proton collisional transfer of H(2s) atoms in the H(2p) state, and production through recombination of H2(+) and H3(+), in an asymmetric ionosphere. According to the present model a large fraction of the observed H Ly-alpha emission from the equatorial region is electron excited, at least at times of solar maximum.

Shemansky, D. E.↗

NASA NTRS1985

Computational methods for hypersonic viscous flow over finite ellipsoid-cones at incidence

A numerical method, which is simpler than others currently in use, is proposed for determining the full viscous flow over a finite body in hypersonic stream at high altitude. It treats the shock layer surrounding the blunt foebody and the near wake behind the base simultaneously by formulating the Navier-Stokes equations in conformal and azimuthal-angle coordinates. The computational domain is confined to the body wall, outflow surface and the bow shock, which is adjusted along the coordinate normal to the wall in the course of iterations. Because of the optimal grid and a well developed alternating direction implicit factorization technique for the governing equations, reasonably accurate results can be obtained on a 30 by 36 by 6 grid with 400 time-marching iterations. Results for body shapes belonging to the ellipsoid-cone family are compared with the experimental data for the Apollo command module and the Viking aeroshell. Validation of the method based on self-consistency is also discussed.

Li, C. P.↗

NASA NTRS1985

An implicit time-marching method for studying unsteady flow with massive separation

A fully implicit time-marching method is developed such that all spatial derivatives are approximated using central differences, but no use is made of any artificial dissipation. The numerical method solves the discretized equations using Alternating Direction Implicit-Block Gaussian Elimination technique. The method is implemented in the unsteady analysis, which solves the incompressible Navier-Stokes equations in terms of vorticity and stream function in generalized orthogonal coordinates. A clustered conformal C-grid is employed, and every effort is made to resolve the various length scales in the flow problem. The metric discontinuity at the branch-cut is treated appropriately using analytic continuation. Introduction of the BGE reordering permits implicit treatment of the branch cut in the numerical method. The vorticity singularity at the cusped trailing edge is also appropriately treated. This accurate and efficient implicit method is used to study flow at Re = 1000, past a 12-percent thick symmetric Joukowski airfoil at high angle of attack 30 and 53 deg.

Osswald, G. A.↗

NASA NTRS1985

Finite-volume scheme for transonic potential flow about airfoils and bodies in an arbitrarily-shaped channel

A conservative finite-volume difference scheme is developed for the potential equation to solve transonic flow about airfoils and bodies in an arbitrary channel. The scheme employs a mesh which is a nearly-conformal 'O' mesh about the airfoil and nearly orthogonal at the channel walls. The mesh extends to infinity upstream and downstream, where the mapping is singular. Special procedures are required to treat the singularities at infinity, including computation of the metrics near those points. Channels with exit areas different from inlet areas are solved; a body with a sting mount is an example of such a case.

South, J. C., Jr.↗

NASA NTRS1985

Analysis of two-dimensional incompressible flow past airfoils using unsteady Navier-Stokes equations

The conservative form of the unsteady Navier-Stokes equations in terms of vorticity and stream function in generalized curvilinear coordinates are used to analyze the flow structure of steady separation and unsteady flow with massive separation. The numerical method solves the discretized equations using an ADI-BGE method. The method is applied to a symmetric 12 percent thick Joukowski airfoil. A conformal clustered grid is generated; several 1-D stretching transformations are used to obtain a grid that attempts to resolve many of the multiple scales of the unsteady flow with massive separation, while maintaining the transformation metrics to be smooth and continuous in the entire flow field. Detailed numerical results are obtained for three flow configurations (1) Re = 1000, alpha = 5 deg, (2) Re = 1000, alpha = 15 deg, (3) Re = 10,000, alpha = 5 deg. No artificial dissipation was added; however, lack of a fine grid in the normal direction has presently led to results which are considered qualitative, especially for case (3).

Ghia, K. N.↗

NASA NTRS1986

Coating Circuit Boards With Silicone

Techniques appropriate to boards containing CMOS circuits detailed. Document presents procedure for applying thin conformal coating to such electronic assemblies as printed-circuit boards and wire-wrapped boards. Coating is from 1 to 7 mils (25 to 178 micrometers) thick and composed of room-temperature-vulcanizing (RTV) silicone. Specifies materials, equipment, spraying method, and quality requirements. Takes into account special needs of circuits made with complementary metal-oxide/semiconductor (CMOS) devices on circuit boards. Special attention given to preventing damage by electrostatic discharge, to which CMOS circuits especially sensitive.

Gaudiano, S.↗

NASA NTRS1985

Numerical procedure for three-dimensional hypersonic viscous flow over aerobrake configuration

A numerical method, which is simpler and more efficient than others currently in use, is proposed for the computation of the full viscous flow over an aerobrake body in hypersonic stream at high altitude. It treats the shock layer surrounding the blunt forebody and the near wake behind the base simultaneously by formulating the Navier-Stokes equations in conformal and azimuthal-angle coordinates. The computational domain is confined by the body wall, outflow surface and the shock, which is adjusted along the coordinate normal to the wall in the course of iterations. Because of the optimal grid and a well developed alternating direction implicit factorization technique for the governing equations, reasonably accurate results can be obtained with a 28 x 36 x 7 grid and 400 time-marching iterations. Excellent agreement of shock location is found between the present result and the schlieren photograph. Details of the base flow and shear layer impingement on the cylindrical aft body are presented for an adiabatic wall case.

Li, C. P.↗

NASA NTRS1985

Research in the design of high-performance reconfigurable systems

The initial control and programming philosophies of the RELAPSE are discussed. A block diagram showing the relationship of the Arithmetic Units (composed of Stages and Bit Processors), to the Functional Units, and other components of the RELAPSE is used to guide this discussion. The latest version of the Bit Processor design is presented. Included is a detailed discussion of the Bit Processor's new scratch pad memory component. The section also clarifies the usage of the Bit Processor's processing registers, and Input/Output functions. The final design phase of the Arithmetic Unit is underway by a study of the Proposed IEEE Floating Point Standard. The decisions on conformation to this standard will be used as inputs into the finalization of the designs of the Bit Processor, Stage, and Arithmetic Units of the RELAPSE.

Slotnick, D. L.↗

NASA NTRS1985

Hot-spot heating susceptibility due to reverse bias operating conditions

Because of field experience (indicating that cell and module degradation could occur as a result of hot spot heating), a laboratory test was developed at JPL to determine hot spot susceptibility of modules. The initial hot spot testing work at JPL formed a foundation for the test development. Test parameters are selected as follows. For high shunt resistance cells, the applied back bias test current is set equal to the test cell current at maximum power. For low shunt resistance cells, the test current is set equal to the cell short circuit current. The shadow level is selected to conform to that which would lead to maximum back bias voltage under the appropriate test current level. The test voltage is determined by the bypass diode frequency. The test conditions are meant to simulate the thermal boundary conditions for 100 mW/sq cm, 40C ambient environment. The test lasts 100 hours. A key assumption made during the development of the test is that no current imbalance results from the connecting of multiparallel cell strings. Therefore, the test as originally developed was applicable for single string case only.

Gonzalez, C. C.↗

NASA NTRS1985

Aeroelastic considerations for torsionally soft rotors

A research study was initiated to systematically determine the impact of selected blade tip geometric parameters on conformable rotor performance and loads characteristics. The model articulated rotors included baseline and torsionally soft blades with interchangeable tips. Seven blade tip designs were evaluated on the baseline rotor and six tip designs were tested on the torsionally soft blades. The designs incorporated a systemmatic variation in geometric parameters including sweep, taper, and anhedral. The rotors were evaluated in the NASA Langley Transonic Dynamics Tunnel at several advance ratios, lift and propulsive force values, and tip Mach numbers. A track sensitivity study was also conducted at several advance ratios for both rotors. Based on the test results, tip parameter variations generated significant rotor performance and loads differences for both baseline and torsionally soft blades.

Mantay, W. R.↗

NASA NTRS1985

The application of diffusion theory to the analysis of hydrogen desorption data at 25 deg C

The application of diffusion theory to the analysis of hydrogen desorption data (coulombs of H2 desorbed versus time) has been studied. From these analyses, important information concerning hydrogen solubilities and the nature of the hydrogen distributions in the metal has been obtained. Two nickel base alloys, Rene' 41 and Waspaloy, and one ferrous alloy, 4340 steel, are studied in this work. For the nickel base alloys, it is found that the hydrogen distributions after electrolytic charging conforms closely to those which would be predicted by diffusion theory. For Waspaloy samples charged at 5,000 psi, it is found that the hydrogen distributions are essentially the same as those obtained by electrolytic charging. The hydrogen distributions in electrolytically charged 4340 steel, on the other hand, are essentially uniform in nature, which would not be predicted by diffusion theory. A possible explanation has been proposed. Finally, it is found that the hydrogen desorption is completely explained by the nature of the hydrogen distribution in the metal, and that the fast hydrogen is not due to surface and sub-surface hydride formation, as was originally proposed.

Danford, M. D.↗

NASA NTRS1985

Aerodynamic properties of turbulent combustion fields

Flow fields involving turbulent flames in premixed gases under a variety of conditions are modeled by the use of a numerical technique based on the random vortex method to solve the Navier-Stokes equations and a flame propagation algorithm to trace the motion of the front and implement the Huygens principle, both due to Chorin. A successive over-relaxation hybrid method is applied to solve the Euler equation for flows in an arbitrarily shaped domain. The method of images, conformal transformation, and the integral-equation technique are also used to treat flows in special cases, according to their particular requirements. Salient features of turbulent flame propagation in premixed gases are interpreted by relating them to the aerodynamic properties of the flow field. Included among them is the well-known cellular structure of flames stabilized by bluff bodies, as well as the formation of the characteristic tulip shape of flames propagating in ducts. In its rudimentary form, the mechanism of propagation of a turbulent flame is shown to consist of: (1) rotary motion of eddies at the flame front, (2) self-advancement of the front at an appropriate normal burning speed, and (3) dynamic effects of expansion due to exothermicity of the combustion reaction. An idealized model is used to illustrate these fundamental mechanisms and to investigate basic aerodynamic features of flames in premixed gases. The case of a confined flame stabilized behind a rearward-facing step is given particular care and attention. Solutions are shown to be in satisfactory agreement with experimental results, especially with respect to global properties such as the average velocity profiles and reattachment length.

Hsiao, C. C.↗

NASA NTRS1986

Interactive algebraic grid-generation technique

An algebraic grid generation technique and use of an associated interactive computer program are described. The technique, called the two boundary technique, is based on Hermite cubic interpolation between two fixed, nonintersecting boundaries. The boundaries are referred to as the bottom and top, and they are defined by two ordered sets of points. Left and right side boundaries which intersect the bottom and top boundaries may also be specified by two ordered sets of points. when side boundaries are specified, linear blending functions are used to conform interior interpolation to the side boundaries. Spacing between physical grid coordinates is determined as a function of boundary data and uniformly space computational coordinates. Control functions relating computational coordinates to parametric intermediate variables that affect the distance between grid points are embedded in the interpolation formulas. A versatile control function technique with smooth-cubic-spline functions is presented. The technique works best in an interactive graphics environment where computational displays and user responses are quickly exchanged. An interactive computer program based on the technique and called TBGG (two boundary grid generation) is also described.

Smith, R. E.↗

NASA NTRS1986

Analytical determination of propeller performance degradation due to ice accretion

A computer code has been developed which is capable of computing propeller performance for clean, glaze, or rime iced propeller configurations, thereby providing a mechanism for determining the degree of performance degradation which results from a given icing encounter. The inviscid, incompressible flow field at each specified propeller radial location is first computed using the Theodorsen transformation method of conformal mapping. A droplet trajectory computation then calculates droplet impingement points and airfoil collection efficiency for each radial location, at which point several user-selectable empirical correlations are available for determining the aerodynamic penalities which arise due to the ice accretion. Propeller performance is finally computed using strip analysis for either the clean or iced propeller. In the iced mode, the differential thrust and torque coefficient equations are modified by the drag and lift coefficient increments due to ice to obtain the appropriate iced values. Comparison with available experimental propeller icing data shows good agreement in several cases. The code's capability to properly predict iced thrust coefficient, power coefficient, and propeller efficiency is shown to be dependent on the choice of empirical correlation employed as well as proper specification of radial icing extent.

Miller, T. L.↗

NASA NTRS1986

Ion Mobility Drift Spectrometer (IMDS) as a flight analytical instrument technique

A detailed knowledge of the history and abundances of the biogenic elements and their compounds throughout the solar system can provide the exobiologists with a basis for understanding the conditions necessary for chemical evolution and the origin of life. The Ion Mobility Drift Spectrometer is an ion molecule reactor coupled with an ion drift spectrometer. Sample molecules are ionized to form product ions in the reactant region. An electric field moves the ions through a drift region against the flow of a drift gas where they are separated according to their size and structure producing an ion mobility spectrum. These spectra provide the IMDS with virtually universal sample identification capability. To conform to the rigid limits of weight, volume and consumables placed on flight instrumentation, several aspects of the IMDS must be studied and redesigned for flight use. In addition to miniaturization of the instrument, a reduction in the high flow rates used for the drift gas is an obvious necessary consideration. The effect of drastically reduced drift flow rates on IMDS spectra was investigated by lowering flow rates from 500ml/min to 50ml/min. Changes in peak shape, drift time and total spectra were studied at each flow rate.

Kojiro, D. R.↗