Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Role of Short-Range Order on Diffusion Coefficients in the Li–Mg Alloy

Li–Mg alloys are important because of their beneficial role in fostering uniform plating and stripping of lithium in all-solid-state batteries. The alloy Li x Mg 1–x forms a solid solution on the BCC crystal structure when the lithium content is greater than x ≈ 0.3. The activation barriers of lithium and magnesium exchanges with a vacancy, crucial for substitutional diffusion, are predicted to be exceptionally low and almost identical, with negligible dependence on the alloy composition. The equilibrium vacancy concentration at room temperature is predicted to be very low, and it also remains almost constant with no dependence on Mg content in the alloy (for x Li ≥ 0.5). Nevertheless, both experiments and kinetic Monte Carlo simulations indicate that the tracer diffusion coefficients decrease by almost an order of magnitude with the addition of Mg to the alloy. In this contribution, the crucial role that chemical short-range order plays in affecting the diffusion coefficients is studied. Chemical short-range order is found to increase the effective activation barrier for lithium and magnesium diffusion by making successive atomic hops with vacancies correlated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Bismuth in Lead–Tin Alloy Perovskites: Effect on Material Properties and Photovoltaic Device Performance

Metal halide perovskites (MHPs) have a strong potential for optoelectronic applications, especially photovoltaics. A significant advantage offered by MHPs is their bandgap tunability via chemical substitution and alloying, with lead–tin alloys producing the narrowest reported bandgaps of ~1.2 eV. Efforts to further narrow the bandgap of MHPs by alloying in other elements, such as bismuth, have largely been unsuccessful due to the introduction of defective electronic states, which severely diminish electronic quality. Here, in this study, we examine the effects of bismuth on a lead–tin alloyed MHP, motivated by the narrow bandgap of alloyed lead–tin MHPs. We find that the defect screening observed in lead–tin MHPs is not sufficient to screen the defect level introduced by bismuth, as evidenced by quenched photoluminescence, decreased mobility, and severely reduced performance in a photovoltaic device. Density functional theory calculations suggest that midgap states are introduced by bismuth addition over a range of chemical and compositional conditions. We further observe through wavelength-dependent photoconductivity that free carriers are generated out to ~0.9 eV in bismuth-containing samples, which could be of potential interest for NIR photodetection.

14 SOLAR ENERGY↗
DOE OSTI2024

Quantitative Mid-infrared Photoluminescence Characterization of Black Phosphorus–Arsenic Alloys

Black phosphorus (bP) is a promising material for mid-infrared (mid-IR) optoelectronic applications, exhibiting high performance light emission and detection. Alloying bP with arsenic extends its operation toward longer wavelengths from 3.7 μm (bP) to 5 μm (bP 3 As 7 ), which is of great practical interest. Quantitative optical characterizations are performed to establish black phosphorus-arsenic (bPAs) alloys optoelectronic quality. Anisotropic optical constants (refractive index, extinction coefficient, and absorption coefficient) of bPAs alloys from near-infrared to mid-IR (0.2-0.9 eV) are extracted with reflection measurements, which helps optical device design. Quantitative photoluminescence (PL) of bPAs alloys with different As concentrations are measured from room temperature to 77 K. PL quantum yield measurements reveal a 2 orders of magnitude decrease in radiative efficiency with increasing As concentration. An optical cavity is designed for bP 3 As 7 , which allows for up to an order of magnitude enhancement in the quantum yield due to the Purcell effect. In conclusion, our comprehensive optical characterization provides the foundation for high performance mid-IR optical device design using bPAs alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Origin of High Activity and Durability of Twisty Nanowire Alloy Catalysts under Oxygen Reduction and Fuel Cell Operating Conditions

The ability to control the surface composition and morphology of alloy catalysts is critical for achieving high activity and durability of catalysts for oxygen reduction reaction (ORR) and fuel cells. Here, this report describes an efficient surfactant-free synthesis route for producing a twisty nanowire (TNW) shaped platinum–iron (PtFe) alloy catalyst (denoted as PtFe TNWs) with controllable bimetallic compositions. PtFe TNWs with an optimal initial composition of ~24% Pt are shown to exhibit the highest mass activity (3.4 A/mg Pt , ~20 times higher than that of commercial Pt catalyst) and the highest durability (<2% loss of activity after 40000 cycles and <30% loss after 120000 cycles) among all PtFe-based nanocatalysts under ORR or fuel cell operating conditions reported so far. Using ex situ and in situ synchrotron X-ray diffraction coupled with atomic pair distribution function (PDF) analysis and 3D modeling, the PtFe TNWs are shown to exhibit mixed face-centered cubic (fcc)-body-centered cubic (bcc) alloy structure and a significant lattice strain. A striking finding is that the activity strongly depends on the composition of the as-synthesized catalysts and this dependence remains unchanged despite the evolution of the composition of the different catalysts and their lattice constants under ORR or fuel cell operating conditions. Notably, dealloying under fuel cell operating condition starts at phase-segregated domain sites leading to a final fcc alloy structure with subtle differences in surface morphology. Due to a subsequent realloying and the morphology of TNWs, the surface lattice strain observed with the as-synthesized catalysts is largely preserved. This strain and the particular facets exhibited by the TNWs are believed to be responsible for the observed activity and durability enhancements. These findings provide new insights into the correlation between the structure, activity, and durability of nanoalloy catalysts and are expected to energize the ongoing effort to develop highly active and durable low-Pt-content nanowire catalysts by controlling their alloy structure and morphology.

25 ENERGY STORAGE↗
DOE OSTI2023

Ultra-strong tungsten refractory high-entropy alloy via stepwise controllable coherent nanoprecipitations

High-performance refractory alloys with ultrahigh strength and ductility are in demand for a wide range of critical applications, such as plasma-facing components. However, it remains challenging to increase the strength of these alloys without seriously compromising their tensile ductility. Here, we put forward a strategy to “defeat” this trade-off in tungsten refractory high-entropy alloys by stepwise controllable coherent nanoprecipitations (SCCPs). The coherent interfaces of SCCPs facilitate the dislocation transmission and relieve the stress concentrations that can lead to premature crack initiation. As a consequence, our alloy displays an ultrahigh strength of 2.15 GPa with a tensile ductility of 15% at ambient temperature, with a high yield strength of 1.05 GPa at 800 °C. The SCCPs design concept may afford a means to develop a wide range of ultrahigh-strength metallic materials by providing a pathway for alloy design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanistic understanding of speciated oxide growth in high entropy alloys

Abstract Complex multi-element alloys are gaining prominence for structural applications, supplementing steels, and superalloys. Understanding the impact of each element on alloy surfaces due to oxidation is vital in maintaining material integrity. This study investigates oxidation mechanisms in these alloys using a model five-element equiatomic CoCrFeNiMn alloy, in a controlled oxygen environment. The oxidation-induced surface changes correlate with each element’s interactive tendencies with the environment, guided by thermodynamics. Initial oxidation stages follow atomic size and redox potential, with the latter becoming dominant over time, causing composition inversion. The study employs in-situ atom probe tomography, transmission electron microscopy, and X-ray absorption near-edge structure techniques to elucidate the oxidation process and surface oxide structure evolution. Our findings deconvolute the mechanism for compositional and structural changes in the oxide film and will pave the way for a predictive design of complex alloys with improved resistance to oxidation under extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Design of refractory multi-principal-element alloys for high-temperature applications

Abstract Refractory multi-principal-element alloys (RMPEAs) exhibit high specific strength at elevated temperatures ( T ). However, current RMPEAs lack a balance of room-temperature (RT) ductility, high- T strength, and high- T creep resistance. Using density-functional theory methods, we scanned composition space using four criteria: (1) formation energies for operational stability: $$-150\le {E}_{{\rm {f}}}$$ − 150 ≤ E f ≤ +70 meV per atom; (2) higher strength found via interstitial electron density with Young’s moduli E > 250 GPa; (3) inverse Pugh ratio for ductility: G / B < 0.57; and (4) high melting points: T m > 2500 °C. Using rapid bulk alloy synthesis and characterization, we validated theory and down-selected promising alloy compositions and discovered Mo 72.3 W 12.8 Ta 10.0 Ti 2.5 Zr 2.5 having well-balanced RT and high- T mechanical properties. This alloy has comparable high- T compressive strength to well-known MoNbTaW but is more ductile and more creep resistant. It is also superior to a commercial Mo-based refractory alloy and a nickel-based superalloy (Haynes-282) with improved high- T tensile strength and creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magnetocaloric effect in Mn-rich Heusler-derived alloys for room temperature-based applications

Magnetic refrigeration-based technologies rely on the magnetocaloric properties of materials and are crucial for improving energy efficiency and for supporting clean environments. However, materials possessing significant magnetocaloric properties that can be used for room temperature-based applications are still lacking. Heusler alloys (such as Mn–Ni–Ga) show giant magnetocaloric effects, which can be further improved by tuning their composition. Herein, we optimized the ratio of Ni to Ga to achieve an alloy with unique magnetocaloric properties. Here, the alloy demonstrated a substantial magnetocaloric effect, attributed to its narrow temperature range for structural and magnetic phase transitions (near room temperature with minimal hysteresis). Structural phase changes were also observed through high-resolution transmission electron microscopy. Optimum entropy changes, calculated from isothermal magnetization curves (4 Tesla magnetic field), were found to be 24.50 J kg −1 K −1 , which is higher than that of state-of-the-art alloys. Experimental demonstration of the magnetocaloric effect (refrigeration cycle) was also carried out using a thermal imaging camera. Furthermore, first-principles calculations were conducted to validate the experimental findings, specifically focusing on the compositional effects on the structural transitions and magnetic properties of the investigated MNG alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

NMR studies of the ground states of Ni 50-x Co x Mn 35 In 15 (x=1, 2.5) and Ni 45 Co 5 Mn 37 In 13 Heusler alloys

Three temperature-induced phase transitions at T=T 1 , T M /T A , and T C , related to the ferromagnetic order of the martensitic phase (FMMP), martensitic (structural) transitions (MT), and the ferromagnetic order of the austenitic phase (FMAP), respectively, have been observed in the off-stoichiometric Heusler alloys, Ni 50-x Co x Mn 35 In 15 (x=1, 2.5) and Ni 45 Co 5 Mn 37 In 13 . In this work, the phase transitions temperatures are found to be depended on alloy composition. A kinetic arrest of the AP was observed for Ni 47.5 Co 2.5 Mn 35 In 15 in the magnetization measurements during field-cooling cycle (FCC) at 50 kOe. Depending upon the cooling protocols, ZFC and FCC (at H = 50 kOe), two different ground states of the alloys can be found in Ni 47.5 Co 2.5 Mn 35 In 15 and Ni 45 Co 5 Mn 37 In 13 alloys. The ground states (T=4.2 K and external field H=0) of the alloys was found to be characterized by three main line: two, partially overlapping, at higher frequencies (300-450 MHz), most likely corresponding of manganese resonance lines and one at lower frequency at about 200 MHz. A significant shift in the spectrum of Ni 45 Co 5 Mn 37 In 13 by about 100 MHz to higher frequencies was observed. The correlation of magnetizations obtained from magnetic moment and NMR studies is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Comparative study of helium bubbles in a Ti-Ta alloy and a Ti/Ta nanocomposite

Here, we investigated the size, density, and distribution of helium (He) bubbles in a Ti-Ta single-phase alloy and a Ti/Ta dual-phase nanocomposite using transmission electron microscopy. The Ti/Ta nanocomposite was fabricated via phase separation during high-temperature annealing of the single-phase Ti-Ta alloy. He ion implantation in the Ti-Ta single-phase alloy leads to the formation of nano-scale He bubbles (~1.7 nm in size, ~2.6×10 5 /μm 3 in volumetric density). He bubbles were found to segregate to grain boundaries. Under identical implantation conditions, numerous He bubbles also formed in the Ti/Ta nanocomposite. Closer inspection revealed that He bubbles in the Ti-rich phase are smaller and of higher volumetric density (~1.2 nm, ~8.4×10 5 /μm 3 ) than those in the Tarich phase (~3 nm, ~1.8×10 5 /μm 3 ) and the single-phase alloy. He bubbles were also observed to decorate phase boundaries, but they were generally smaller than those on grain boundaries. These results suggest that Ti/Ta phase boundaries are less conducive to the growth of large He bubbles than grain boundaries in the Ti-Ta single phase alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Model of Hydrogen Solubility in Palladium-Silver Alloys

Fusion fuel cycle designs depend on palladium and palladium-silver alloys. The selective permeability of these is used to separate hydrogen isotopes from other elements. Predicting the solubility of hydrogen isotopes in palladium-silver alloys is important for the design of key unit operations for tritium processing. This paper presents a model of hydrogen isotope solubility in palladium and palladium-silver alloys based on Guggenheim’s quasichemical lattice theory. The model parameters were determined as functions of isotope molecular weight and the silver content of the alloy. The model predicts reasonable values for the solubility of protium, deuterium, and tritium over a wide range of temperatures, pressures, and alloy compositions.

08 HYDROGEN↗
DOE OSTI2024

Utilizing integrated neutron diffraction and elastoplastic self-consistent crystal plasticity model to quantitatively assess the strengthening mechanism in Al–12.5Ce and Al–12.5Ce–0.4Mg alloys

An integrated in-situ neutron diffraction and elastic plastic self-consistent crystal plasticity (EPSC-CP) modeling scheme is performed on a binary Al–12Ce alloy and a ternary Al–12Ce–0.4Mg alloys. Using this scheme, the constitutive parameters, i.e. elastic constants and slip system parameters of individual phases can be calibrated which can be used in microstructure-based CP models to predict materials performance. From this study, it is shown that the elastic constants of Al 11 Ce 3 intermetallics calculated from density function theory calculation in the literature are rather accurate. When applied to the EPSC-CP model, the lattice strains of both the binary and ternary alloys are correctly predicted as compared with experiments, and large lattice strain differences between Al (100) plane and Al 11 Ce 3 (010) plane are demonstrated. The slip system parameters calibrated by the scheme shows that the addition of 0.4 wt% Mg in the alloy has little influence on the critical resolved shear stress of initial dislocation glide in the Al matrix which caused plastic yield in the material. This can be explained by the very dilute Mg solute content in the Al solid solution, causing large spacing of Al–Mg lattice misfit sites and little impact on resistance of dislocation glide at initial yield. The 0.4 wt% Mg addition, on the other hand, has a large influence on the hardening term in the slip system parameters, indicating those Al–Mg misfit sites do help dislocation accumulation during the deformation. The impact of dilute Mg addition on the Al slip system parameters is also reflected in the flow behavior of the ternary alloy: little impact on the yield stress, but a large impact on working hardening and tensile strength of the materials which is consistent with the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Laser metal deposition of refractory high-entropy alloys for high-throughput synthesis and structure-property characterization

Progress in materials development is often paced by the time required to produce and evaluate a large number of alloys with different chemical compositions. This applies especially to refractory high-entropy alloys (RHEAs), which are difficult to synthesize and process by conventional methods. To evaluate a possible way to accelerate the process, high-throughput laser metal deposition was used in this work to prepare a quinary RHEA, TiZrNbHfTa, as well as its quaternary and ternary subsystems by in-situ alloying of elemental powders. Compositionally graded variants of the quinary RHEA were also analyzed. Our results show that the influence of various parameters such as powder shape and purity, alloy composition, and especially the solidification range, on the processability, microstructure, porosity, and mechanical properties can be investigated rapidly. The strength of these alloys was mainly affected by the oxygen and nitrogen contents of the starting powders, while substitutional solid solution strengthening played a minor role.

additive manufacturing↗
DOE OSTI2023

Microstructural Characterization of Ion Irradiated ODS MA956 Alloy

Oxide Dispersion Strengthened (ODS) alloys are considered as promising nuclear materials for the next generation advanced nuclear reactors due to their improved elevated temperature mechanical properties and radiation damage resistance. MA956 is a commercial ODS alloy with superior oxidation resistance and creep strength at elevated temperatures. The improved properties for ODS alloys can be attributed to the presence of dispersed nanosized oxide particles. These oxide particles can act as barriers to dislocation motion and provide additional sinks and sites for point defect recombination. Hence, their stability can greatly affect the properties of the irradiated ODS alloys. Besides, irradiation will induce defects into the ODS alloys, and these defects can develop further as irradiation dose increases. Furthermore, the defects propagation can significantly undermine the mechanical properties of the bulk materials, resulting in irradiation hardening and lower ductility. Therefore, it is necessary to have a good understanding of the defect’s evolution with irradiation. Hence, efforts are ongoing to understand the effect of ion irradiation on ODS MA956 with emphasis on oxide particles and evolution of defects as a function of dose (2.5, 50 and 100 dpa).

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Understanding Twinning and Deformation in High Entropy Alloys

On the one hand, multi-principal element alloys (MPEAs) have created a paradigm shift in alloy design due to large compositional space, whereas on the other, they have presented enormous computational challenges for theory-based materials design, especially density functional theory (DFT), which is inherently computationally expensive even for traditional dilute alloys. In this project, we developed a machine learning framework, namely PREDICT ( PR edict properties from E xisting D atabase I n C omplex alloys T erritory), that opens a pathway to predict elastic constants in large compositional space with little computational expense. The framework only relies on the DFT database of binary alloys and predicts Voigt–Reuss–Hill Young’s modulus, shear modulus, bulk modulus, elastic constants, and Poisson’s ratio in MPEAs. We show that the key descriptors of elastic constants are the A–B bond length and cohesive energy. The framework can predict elastic constants in hypothetical compositions as long as the constituent elements are present in the database, thereby enabling property exploration in multi-compositional systems. We illustrate predictions in a FCC Ni-Cu-Au-Pd-Pt system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Radiolytic Gas Production from Aluminum Coupons (Alloy 1100 and 6061) in Helium Environments—Assessing the Extended Storage of Aluminum Clad Spent Nuclear Fuel

Corrosion of aluminium alloy clad nuclear fuel, during reactor operation and under subsequent wet storage conditions, promotes the formation of aluminium hydroxide and oxyhydroxide layers. These hydrated mineral phases and the chemisorbed and physisorbed waters on their surfaces are susceptible to radiation-induced processes that yield molecular hydrogen gas (H 2 ), which has the potential to complicate the long-term storage and disposal of aluminium clad nuclear fuel through flammable and explosive gas mixture formation, alloy embrittlement, and pressurization. Here, we present a systematic study of the radiolytic formation of H 2 from aluminium alloy 1100 (AA1100) and 6061 (AA6061) coupons in “dry” (~0% relative humidity) and “wet” (50% relative humidity) helium environments. Cobalt-60 gamma irradiation of both aluminium alloy types promoted the formation of H 2 , which increased linearly up to ~2 MGy, and afforded G-values of 1.1 ± 0.1 and 2.9 ± 0.1 for “dry” and “wet” AA1100, and 2.7 ± 0.1 and 1.7 ± 0.1 for “dry” and “wet” AA6061. The negative correlation of H 2 production with relative humidity for AA6061 is in stark contrast to AA1100 and is attributed to differences in the extent of corrosion and varying amounts of adsorbed water in the two alloys, as characterized using optical profilometry, scanning electron microscopy, Raman spectroscopy, and X-ray diffraction techniques.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Hydrothermal Corrosion of Latest Generation of FeCrAl Alloys for Nuclear Fuel Cladding

After the Fukushima nuclear disaster, the nuclear materials community has been vastly investing in accident tolerant fuel (ATF) concepts to modify/replace Zircaloy cladding material. Iron–chromium–aluminum (FeCrAl) alloys are one of the leading contenders in this race. In this study, we investigated FA-SMT (or APMT-2), PM-C26M, and Fe17Cr5.5Al over a time period of 6 months in simulated BWR environments and compared their performance with standard Zirc-2 and SS316 materials. Our results implied that water chemistry along with alloy chemistry has a profound effect on the corrosion rate of FeCrAl alloys. Apart from SS316 and Zirc-2 tube specimens, all FeCrAl alloys showed a mass loss in hydrogen water chemistry (HWC). FA-SMT displayed minimal mass loss compared to PM-C26M and Fe17Cr5.5Al because of its higher Cr content. The mass gain of FeCrAl alloys in normal water chemistry (NWC) is significantly less when compared to Zirc-2.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural Transitions during Powder Metallurgical Processing of Solute Stabilized Nanostructured Tungsten Alloys

Exploiting grain boundary engineering in the design of alloys for extreme environments provides a promising pathway for enhancing performance relative to coarse-grained counterparts. Due to its attractive properties as a plasma facing material for fusion devices, tungsten presents an opportunity to exploit this approach in addressing the significant materials challenges imposed by the fusion environment. Here, we employ a ternary alloy design approach for stabilizing W against recrystallization and grain growth while simultaneously enhancing its manufacturability through powder metallurgical processing. Mechanical alloying and grain refinement in W-10 at.% Ti-(10,20) at.% Cr alloys are accomplished through high-energy ball milling with transitions in the microstructure mapped as a function of milling time. We demonstrate the multi-modal nature of the resulting nanocrystalline grain structure and its stability up to 1300 °C with the coarser grain size population correlated to transitions in crystallographic texture that result from the preferred slip systems in BCC W. Field-assisted sintering is employed to consolidate the alloy powders into bulk samples, which, due to the deliberately designed compositional features, are shown to retain ultrafine grain structures despite the presence of minor carbides formed during sintering due to carbon impurities in the ball-milled powders.

36 MATERIALS SCIENCE↗