Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “W”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Development of a PPT for the EO-1 Spacecraft

A Pulsed Plasma Thruster (PPT) has been developed for use in a technology demonstration flight experiment on the Earth Observing 1 (EO-1) New Millennium Program mission. The thruster replaces the spacecraft pitch axis momentum wheel for control and momentum management during an experiment of a minimum three-day duration. The EO-1 PPT configuration is a combination of new technology and design heritage from similar systems flown in the 1970's and 1980's. Acceptance testing of the protoflight unit has validated readiness for flight, and integration with the spacecraft, including initial combined testing, has been completed. The thruster provides a range of capability from 90 microN-sec impulse bit at 650 sec specific impulse for 12 W input power, through 860 microN-sec impulse bit at 1400 see specific impulse for 70 W input power. Development of this thruster reinitiates technology research and development and re-establishes an industry base for production of flight hardware. This paper reviews the EO-1 PPT development, including technology selection, design and fabrication, acceptance testing, and initial spacecraft integration and test.

Benson, Scott W.↗
NASA NTRS1972

Development of wire drawing processes for refractory metal fibers

Fabrication schedules were developed for producing wire, 0.25 mm to 0.51 mm diameter, from the refractory metal alloys ASTAR-811C, B-88 and W-Hf-C. Tensile properties were evaluated at room temperature and up to 1204 C. Also, the stress rupture properties of the alloys at 1093 C were determined. W-Hf-C and B-88 were found to have the best mechanical properties on a strength to density basis. The fabrication schedules for producing wire from these two alloys were further improved with regards to the wire quality and material yield under the optimization of fabrication schedule.

King, G. W.↗
NASA NTRS1971

Vibrational population of the A super 3 sigma sub u/+/ and B super 3 pi sub g states of N2 in normal auroras.

Use of new electron impact excitation cross sections for the six lowest triplet states (A, B, W, C, E, D) of N2, and solution of the coupled equations of statistical equilibrium to obtain the vibrational population of each electronic state. The results show that cascade from high levels of the A super 3 sigma sub u(+) state and from the W super 3 delta sub u state is significant in populating the lower vibrational levels of the B state and hence the character of its ?apparent' excitation cross sections. For the B state excited under auroral conditions, the fraction of the total population due to cascade processes exceeds 25% for all levels lower than 7 and is greater than 80% for B(v' = 0). For the A state under similar conditions, cascade from the B state contributes 50% or more of the total vibrational population for levels lower than 7, and 80% or more for levels below 4. For levels of the A state greater than 7, the A yields B transitions depopulate the levels rapidly and indicate that the Vegard-Kaplan emissions from these higher levels will be weak or totally absent in normal auroras.

Cartwright, D. C.↗
NASA NTRS1973

Design and development of liquid hydrogen mixer unit

A dc brushless motor driven mixer unit (a vaneaxial fan) was designed and evaluated for use in cryogenic fluids (liquids and gases). It was found to operate well in all fluids in which it was tested. The test fluids were liquid and gaseous helium, hydrogen in the liquid phase gas phase and mixtures of the two phases, and liquid nitrogen. It operated for over 100 hr at cryogenic temperatures without damage to the bearings and at the conclusion of testing the condition of the bearings was such that an operational life of 5000 hr appeared possible. The unit demonstrated that (with the brushless dc motor principle) useful pumping of cryogenic fluids could be accomplished with very small power inputs to the mixer motor. During test, the motor input power varied from approximately 0.5 W to 2.5 W, depending on fluid density. The high power input produced a mixer efficiency of over 49 percent. In an earlier program (see NASA Report CR-72365), a mixer using an ac induction motor demonstrated an efficiency of 17.7 percent under the same conditions, illustrating the advantage of the dc brushless motor driven unit. The mixer also demonstrated its ability to automatically vary speed as a function of the density of the fluid being pumped. This causes the unit to deliver higher volumetric flow rates as fluid density decreases.

Morgan, R. W.↗
NASA NTRS1975

Comparison of high-latitude and mid-latitude ionospheric electric fields

Simultaneous measurements of the F region electric field by the incoherent scatter technique have been made at Chatanika, Alaska (65.1 deg N, 147.5 deg W), and Millstone Hill, Massachusetts (42.6 deg N, 71.5 deg W), on July 18-19 and Aug. 7-8, 1973. Good correlation was observed in the time variation of the perpendicular electric field at the two stations. Magnetic conditions for these days were relatively quiet with some variations evident from the high-latitude magnetograms and the Chatanika radar, but no distinct effect appeared on the mid-latitude magnetograms. Since magnetospheric electric fields are thought to be the source of high-latitude electric fields such as those observed at Chatanika, the good correlation in the perpendicular electric field for the two stations indicates that the magnetospheric originated electric fields have an appreciable effect down to at least L equals 3.2.

Carpenter, L. A.↗
NASA NTRS1975

Experimental studies of flow separation and stalling on two-dimensional airfoils at low speeds. Phase 2: Studies with Fowler flap extended

Results were given on experimental studies of flow separation and stalling on a two-dimensional GA(W)-1 17 percent thick airfoil with an extended Fowler flap. Experimental velocity profiles obtained from a five tube probe survey with optimum flap gap and overlap setting (flap at 40 deg) are shown at various stations above, below, and behind the airfoil/flap combination for various angles of attack. The typical zones of steady flow, intermittent turbulence, and large scale turbulence were obtained from a hot wire anemometer survey and are depicted graphically for an angle of attack of 12.5 deg. Local skin friction distributions were obtained and are given for various angles of attack. Computer plots of the boundary layer profiles are shown for the case of the flap at 40 deg. Static pressure contours are also given. A GA(W)-2 section model was fabricated with 30 percent Fowler flaps and with pressure tabs.

Seetharam, H. C.↗
NASA NTRS1976

A 128K-bit CCD buffer memory system

A prototype system was implemented to demonstrate that CCD's can be applied advantageously to the problem of low power digital storage and particularly to the problem of interfacing widely varying data rates. 8K-bit CCD shift register memories were used to construct a feasibility model 128K-bit buffer memory system. Peak power dissipation during a data transfer is less than 7 W., while idle power is approximately 5.4 W. The system features automatic data input synchronization with the recirculating CCD memory block start address. Descriptions are provided of both the buffer memory system and a custom tester that was used to exercise the memory. The testing procedures and testing results are discussed. Suggestions are provided for further development with regards to the utilization of advanced versions of CCD memory devices to both simplified and expanded memory system applications.

Siemens, K. H.↗
NASA NTRS1978

Performance of a thermionic converter module utilizing emitter and collector heat pipes

A thermionic converter module simulating a configuration for an out-of-core thermionic nuclear reactor was designed, fabricated, and tested. The module consists of three cylindrical thermionic converters. The tungsten emitter of the converter is heated by a tungsten, lithium heat pipe. The emitter heat pipes are immersed in a furnace, insulated by MULTI-FOIL thermal insulation, and heated by tungsten radiation filaments. The performance of each thermionic converter was characterized before assembly into the module. Dynamic voltage, current curves were taken using a 60 Hz sweep and computerized data acquisition over a range of emitter, collector, and cesium-reservoir temperatures. An output power of 215 W was observed at an emitter temperature of 1750 K and a collector temperature of 855 K for a two diode module. With a three diode module, an output power of 270 W was observed at an average emitter temperature of 1800 K and a Collector temperature of 875 K.

Kroeger, E. W.↗
NASA NTRS1978

A wide bandwidth CCD buffer memory system

A prototype system was implemented to demonstrate that CCD's can be applied advantageously to the problem of low power digital storage and particularly to the problem of interfacing widely varying data rates. CCD shift register memories (8K bit) were used to construct a feasibility model 128 K-bit buffer memory system. Serial data that can have rates between 150 kHz and 4.0 MHz can be stored in 4K-bit, randomly-accessible memory blocks. Peak power dissipation during a data transfer is less than 7 W, while idle power is approximately 5.4 W. The system features automatic data input synchronization with the recirculating CCD memory block start address. System expansion to accommodate parallel inputs or a greater number of memory blocks can be performed in a modular fashion. Since the control logic does not increase proportionally to increase in memory capacity, the power requirements per bit of storage can be reduced significantly in a larger system.

Siemens, K.↗
NASA NTRS1978

Nighttime dynamics of the F region near Arecibo as mapped by airglow features

A scanning photometer was used to obtain red line airglow measurements at Arecibo in order to determine the direction and phase velocity of propagation of major airglow enhancements. The scans were made in the N-S direction on 13 nights and in the E-W direction on five nights. The most common type of descent begins in the south and progresses northward, with an apparent phase velocity of the order of 300 m/s. Neutral winds are apparently the cause of this type of descent. Observed descents of the equatorial ionosphere are described, and their relation to airglow enhancement is considered. A second type of airglow enhancement was seen occasionally and travels from north to south; this enhancement is probably due to traveling ionospheric disturbances. A third type previously unreported involves sudden descents lasting an hour or so and sometimes ocurring nearly simultaneously over regions extending at least 1000 km in the N-S or E-W direction.

Sobral, J. H. A.↗
NASA NTRS1979

Volume-pumped nuclear lasers

A summary is given to experimental results on volume-pumped nuclear lasers obtained at the Langley Research Center. The first volume-pumped nuclear laser was achieved in 1976 using the He-3(n, p)H-3 reaction. Since that time laser output has increased by more than a factor of 1000 (from mW to W). Lasing has been demonstrated in He-3-Ar (1.27 and 1.79 micron), He-3-Xe (2.027, 3.5, and 3.65 microns), He-3-Kr (2.19 and 2.52 microns), and He-3-Cl (1.587 micron). Pressures of the lasing mixture range from 300 torr to 4 atm with a peak power output of 26 W were achieved in a He-3-Ar mixture with a multiple-pass laser configuration.

Hohl, F.↗
NASA NTRS1980

Design and flight performance of the Pioneer Venus Multiprobe and Orbiter solar arrays

The designs of the solar arrays for the Pioneer Venus Orbiter and Multiprobe spacecraft are described, and the power output predicted for these arrays is compared with the in-space performance. The Orbiter solar array was designed to produce a minimum of 329 W at 28 V after 243 days in Venus orbit, except during eclipses and periapsis phases, when battery power was to be used. After 492 days in orbit, this solar array was producing 365.3 W at 29.6 V, exceeding its design objectives. The Multiprobe solar array produced sufficient power at low sun angles to effect the release of the large probe and the three small probes and to power the scientific instruments onboard the spacecraft during its approach and destructive entry into the Venusian atmosphere.

Goldhammer, L. J.↗
NASA NTRS1980

Fabrication and surface characterization of composite refractory compounds suitable for thermionic converters

Thermal faceting was observed for the high index planes of LaB6. The (100), (110), and (111) planes were found to be the most thermodynamically stable faces in vacuum in a study of electrode materials for thermionic emitters. The properties of adsorbed carbon, cesium, and cesium-oxygen layers were investigated on LaB6 single crystal surfaces as well as on Zr/0/W(100) and W(100). Cesium was found to increase electron reflection near the collision threshold on LaB6(100) and W(100) and to decrease the reflection on Zr/0/W(100). This difference may be explained by the unusually high threshold reflection coefficient of Zr/0/W without adsorbed cesium.

Davis, P. R.↗
NASA NTRS1981

Contact binary stars

Densities, corrected primary colors, minimum periods, inferred masses, luminosities, and specific angular momenta are computed from data on 37 W Ursae Majoris systems. A-type systems, having lower densities and angular momenta than the W-type systems, are shown to be evolved, and a new class of contact binary is identified, the OO Aquilae systems, whose members have evolved into contact. Evolutionary grids based on the contact condition agree with observation, except in that the evolved A-type systems have lost more angular momentum than predicted by gravitational radiation alone. This is accounted for by stellar wind magnetic braking, which is shown to be effective on a shorter time scale and to be important in other kinds of binaries containing a cool, tidally coupled component.

Mochnacki, S. W.↗
NASA NTRS1982

MC carbide structures in M(lc2)ar-M247

The morphologies and distribution of the MC carbides in Mar-M247 ingot stock and castings were investigated using metallographic, X-ray diffraction and energy-dispersive X-ray analysis techniques. The MC carbides were found to form script structures during solidification. The script structures were composed of three distinct parts. The central cores and elongated arms of the MC carbide script structures had compositions (Ti, Cr, Hf, Ta, W)C and lattice parameters of 4.39 A. The elongated script arms terminated in enlarged, angular "heads". The heads had compositions (Ti, Hf, Ta, W)C and lattice parameters of approximately 4.50 A. The heads had a higher Hf content than the cores and arms. The size of the script structures, as well as the relative amount of head-type to core and arm-type MC carbide, was found to be determined by solidification conditions. No carryover of the MC carbides from the ingot stock to the remelted and cast material was observed.

Wawro, S. W.↗
NASA NTRS1983

First VHF auroral radar interferometer observations

Auroral plasma instabilities were investigated using the radar interferometer technique based on observations obtained with a 49.92 MHz, 20-25 KW peak power pulsed radar located in Ithaca, NY (42.5 degrees N, 76.4 degrees W). Strong auroral echoes obtained during several highly active periods were analyzed. Phase differences between the signals received on the two antennas were utilized to accurately determine the E-W position, within the scattering volume, of localized scattering centers, and changes in this phase were used to determine the corresponding velocity. The radial (essentially N-S) motion was described by the signal Doppler shift. It is found that these data provide detailed information on the turbulent structure of the echoing region and show clearly that different features in the Doppler power spectrum often represent signals coming from different locations. It is concluded that these data can be utilized to determine full horizontal velocity vectors and hence the horizontal electric field, usually with a time resolution of the order of 15-30 s.

Providakes, J. F.↗