Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Voids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Morphologically Stable Li/Electrolyte Interface for All-Solid-State Batteries Enabled by 3D-Micropatterned Garnet

Morphological degradation at the Li/solid-state electrolyte (SSE) interface is a prevalent issue causing performance fading of all-solid-state batteries (ASSBs). To maintain the interfacial integrity, most ASSBs are operated under low current density with considerable stack pressure, which significantly limits their widespread usage. In this work, a novel 3D-micropatterned SSE (3D-SSE) that can stabilize the morphology of the Li/SSE interface even under relatively high current density and limited stack pressure is reported. Under the pressure of 1.0 MPa, the Li symmetric cell using a garnet-type 3D-SSE fabricated by laser machining shows a high critical current density of 0.7 mA cm –2 and stable cycling over 500 h under 0.5 mA cm –2 . This excellent performance is attributed to the reduced local current density and amplified mechanical stress at the Li/3D-SSE interface. These two effects can benefit the flux balance between Li stripping and creep at the interface, thereby pre-venting interfacial degradation such as void formation and dendrite growth.

3D-micropatterned garnet↗
DOE OSTI2023

Microstructural Insights into Performance Loss of High-Voltage Spinel Cathodes for Lithium-ion Batteries

Spinel-structured LiNi x Mn 2-x O 4 (LNMO), with low-cost earth-abundant constituents, is a promising high-voltage cathode material for lithium-ion batteries. Even though extensive electrochemical investigations have been conducted on these materials, few studies have explored correlations between their loss in performance and associated changes in microstructure. Here, down to the atomic scale, the structural evolution of these materials is investigated upon the progressive cycling of lithium-ion cells. Transgranular cracking is revealed to be a key feature during cycling; this cracking is initiated at the particle surface and leads to the penetration of electrolytes along the crack path, thereby increasing particle exposure to the electrolyte. The lattice structure on the crack surface shows spatial variances, featuring a top layer of rock-salt, a sublayer of a Mn 3 O 4 -like arrangement, and then a mixed-cation region adjacent to the bulk lattice. The transgranular cracking, along with the emergence of local lattice distortion, becomes more evident with extended cycling. Further, phase transformation at primary particle surfaces and void formation through vacancy condensation is found in the cycled samples. All these features collectively contribute to the performance degradation of the battery cells during electrochemical cycling.

25 ENERGY STORAGE↗
DOE OSTI2021

Temperature and radiation effects on brittle versus ductile fracture behavior in miscible phase boundaries: insight from atomistic simulations

Temperature- and irradiation-assisted failure mechanisms in miscible phase boundaries are clarified via atomistic calculations. We first establish the temperature-dependent brittle-to-ductile transition in U–Zr miscible phase boundaries. Our results confirm that these boundaries are mostly brittle at low temperatures and ductile at elevated temperatures. We then investigate the changes induced by irradiation on the fracture mechanisms in such phase boundaries. The irradiation-induced defect accumulation follows a multi-stage process that starts with the accumulation of isolated small dislocation loops before transitioning to the saturation and growth of larger dislocation loops and end up with a reorganization into forest dislocations. The accumulation of loops is the primary feature to participate in the delineation between brittle and ductile interfacial fracture in irradiated phase boundaries. At low damage levels, radiation defect interactions with the crack tip are limited and U–Zr miscible boundaries fail through the emission of dislocations ahead of the crack tip followed by brittle cleavage in agreement with the classical Griffith’s criterion for crack stability. At higher damage levels, the failure mode transitions from brittle crack growth to ductile void growth. In this case, the microcrack tip is blunted by the high density of pre-existing, radiation-induced defects in the vicinity of the crack. This interaction leads to the development and growth of a cavity at the interface as opposed to interfacial cleavage.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Temperature and dose effects on dislocation loops in self-ion irradiated high-purity iron

Body-centered cubic (BCC) Fe-based alloys are promising candidate materials for advanced nuclear reactors. However, a detailed understanding of irradiation induced dislocation loop microstructure development remains unresolved. It is a widespread belief that 〈001〉 loops become increasingly favorable over ½〈111〉 loops as irradiation temperature rises above ∼300 C. Unfortunately, the temperature effects on 〈001〉 loop have been primarily examined in in-situ irradiation on TEM thin foils but poorly explored on bulk Fe due to exceedingly limited experimental studies on bulk specimens, raising concerns about the potential influence of TEM thin foil artifacts on observed results. Here, in this study, we conducted experiments on ultra-high purity BCC Fe specimens irradiated with 6.7–8 MeV Fe ions over a wide temperature range on bulk samples. We investigated the effects of temperature (T irr = 250–500 °C), dose rate (10⁻⁵ to 10⁻³ dpa/s), and dose (0.35 to 3.5 dpa) on the formation and evolution of 〈001〉 and ½〈111〉 loops as well as cavity (void) formation. Post-irradiation Burgers vector analysis via g•b method on dislocation segments and loops revealed that 〈001〉 loop fraction does not show a monotonic positive correlation with irradiation temperature. Combined with previous and current theoretical as well as experimental findings, we explore the temperature effects on all existing models of 〈001〉 loop formation. We conclude that the prevailing reports regarding the dominance of 〈001〉 loops in Fe at elevated temperatures are mainly attributable to the loss of glissile ½〈111〉 clusters in TEM thin foil experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reconstruction of concrete microstructure using complementarity of X-ray and neutron tomography

The concrete microstructure was successfully reconstructed using the complementarity of X-ray and neutron computed tomography (CT). Neither tomogram alone was found to be suitable to properly describe the microstructure of concrete under this study. However, by merging the information revealed by the two modalities, and using image segmentation, noise reduction, and image registration techniques we reconstruct the concrete microstructure. Void, aggregate, and cement paste phases are successfully captured down to the images' spatial resolution, even though the aggregate consists of multiple minerals. The coarse-aggregate volume fraction of the reconstructed microstructure was similar to that of the mixing proportions. Furthermore, image-based finite element analysis is performed to demonstrate the effects of microstructure on stress concentration and strain localization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Alkali-silica reaction products and cracks: X-ray micro-tomography-based analysis of their spatial-temporal evolution at a mesoscale

In this study, we propose a laboratory-scale methodology, based on X-ray micro-tomography and caesium (Cs) as a contrast agent, to advance the understanding of cracking due to alkali-silica reaction (ASR) in concrete. The methodology allows achieving a completely non-destructive and time-lapse characterization of the spatial-temporal patterns of both the cracks and the ASR products. While Cs addition slightly accelerated the ASR kinetics, the crack patterns, with and without Cs addition, were statistically equivalent. Cracks with ASR products appeared first in the aggregates, close to the interface with the cement paste. They propagated afterwards towards the aggregates interior. Some products were then extruded for several mm into air voids and cracks in the cement paste. This process suggests that, in the early stage, the ASR products may be a low-viscosity gel that can flow away from the source aggregate and may settle later elsewhere as a rigid phase, upon calcium uptake.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Extended defects-enhanced oxygen diffusion in ThO 2

Oxygen self-diffusion is key to understanding stoichiometry and defect structures in oxide nuclear fuels. Experimentally, low activation-barrier oxygen migration was found in ThO 2 , a candidate nuclear fuel, possibly due to short-circuit diffusion mechanisms. Here, we perform extensive molecular dynamics simulations to show that various types of extended defects can enhance oxygen self-diffusion with a much-reduced activation barrier in ThO 2 . In this work, we consider extended defects including 1D (dislocation), 2D (grain boundary), and 3D (void) defects. Due to the distinct characteristics of each type of extended defect, the modulation of oxygen diffusion varies. Further, these results provide a quantitative description of oxygen transport, which is significantly enhanced within a close distance (nanometer scale) from the extended defects. Among all these considered defects, grain boundary, particularly the low-energy $Σ$3 twin boundary, exhibits the strongest effect on increasing oxygen transport.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Fabrication of yeast engineered porous 13X adsorbent layers for CO 2 capture

This study investigates a novel environmentally friendly coating technique using yeast fermentation to obtain super porous Zeolite 13X adsorbent layers through freeze-drying technique for CO 2 capture applications. Several mass ratios of sugar to yeast were used to control the porosity and pore sizes in the adsorbent layer. A unique peeling process was integrated to obtain foamy, hollow structures to have deeper layer accessibility of adsorbent for adsorption applications. These coated adsorbent layers were experimentally characterized as a function of the mass ratio of sugar to yeast and adsorbent solid fraction. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FT-IR) are used to analyze the coated layers. Here, the void fraction for coated samples is found to vary between 0.48 and 0.56, making the samples applicable for adsorption applications. Adsorption performance experiments are performed to test the coated samples' performance compared to 13X powder. Due to their simplistic fabrication, cost-effectiveness, rapid pore formation, and high adsorption capacity, these porous 13X layers hold potential for large-scale fabrication and CO 2 capture applications.

Adsorbent coating↗
DOE OSTI2024

Parameterization of vacancy production rate in phase-field models of fission gas bubble evolution in nuclear fuel

Phase-field modeling has increasingly been used to study microstructural evolution in fission gas bubbles in nuclear fuel to improve understanding of fission gas release. To improve computational efficiency, often only vacancies and gas atoms are included as defect species. In this case, the net effects of vacancy and interstitial production, recombination, and biased sink absorption are included as a net vacancy source, or net vacancy source combined with an effective sink. However, there has been a lack of clarity on what parameter values should be used for these approaches to best match the more complete physical picture that includes interstitials and vacancies. Here, we compare a phase-field model of void growth to analytical models for the source-only and source plus sink approach to gain insight into how the phase-field models can be parameterized effectively. The source-only approach provides greater flexibility to match growth rates determined from the full vacancy-interstitial picture. A strategy was developed for determining the value of the net vacancy source term by comparing to an analytical model that includes vacancy and interstitial production, recombination, and biased sink absorption. Finally, this strategy can be used to parameterize phase-field models of fission gas bubble growth.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Relationship between ductility and the porosity of additively manufactured AlSi10Mg

Additive manufacturing via selective laser melting can result in variable levels of internal porosity both between build plates and within components from the same build. In this work, sample porosity levels were compared to tensile properties for 176 samples spanning eight different build plates. Sample porosity was measured both by Archimedes density, which provided an estimation of overall porosity, and by observation of voids in the fracture surface, which provided an estimation of the porosity at the failure plane. The porosity observed at the fracture surface consistently demonstrated higher porosity than that suggested by Archimedes density. The porosity values obtained from both methods were compared against the mechanical results. Sample porosity appears to have some correlation to the ultimate tensile strength, yield strength, and modulus, but the strongest relationship is observed between porosity and ductility. Three different models were used to relate the fracture surface porosity to the ductility. The first method was a simple linear regression analysis, while the other two models have been used to relate porosity to ductility in cast alloys. It is shown that all three models fit the data well over the observed porosity ranges, suggesting that the models taken from casting theory can extend to additively manufactured metals. Finally, it is proposed that the non-destructive Archimedes method could be used to estimate an approximate sample ductility through the use of correlations realized here. Such a relationship could prove useful for design and for a deeper understanding of the impact of pores on tensile behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Sustained Oxygen Spectral Gaps and Their Dynamic Evolution in the Inner Magnetosphere

Van Allen Probes observations of ion spectra often show a sustained gap within a very narrow energy range throughout the full orbit. To understand their formation mechanism, we statistically investigate the characteristics of the narrow gaps for oxygen ions and find that they are most frequently observed near the noon sector with a peak occurrence rate of over 30%. The magnetic moment (μ) of the oxygen ions in the gap shows a strong dependence on magnetic local time (MLT), with higher and lower μ values in the morning and afternoon sectors, respectively. Moreover, we find through superposed epoch analysis that the gap formation also depends on geomagnetic conditions. Those gaps formed at lower magnetic moments (μ < 3,000 keV/G) are associated with stable convection electric fields, which enable magnetospheric ions to follow a steady drift pattern that facilitates the gap formation by corotational drift resonance. On the other hand, gaps with higher μ values are statistically preceded by a gradual increase of geomagnetic activity. Here, we suggest that ions within the gap were originally located inside the Alfven layer following closed drift paths, before they were transitioned into open drift paths as the convection electric field was enhanced. The sunward drift of these ions, with very low fluxes, forms a drainage void in the dayside magnetosphere manifested as the sustained gap in the oxygen spectrum. This scenario is supported by particle-tracing simulations, which reproduce most of the observed characteristics and therefore provide new insights into inner magnetospheric dynamics.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

In-Situ Transmission Electron Microscopy Study of the Evolution of Extended Defects in Oxide Nuclear Fuels

In-situ transmission electron microscopy (TEM) with simulated extreme environments is an effective tool for understanding and tracking microstructural changes down to the atomic scale. The objective of this research is to study the effect of temperature on the evolution of extended defects in ThO2 and UO2. Here, we present in-situ TEM isochronal thermal annealing experiments using a micro-electro-mechanical-system (MEMS)-based heating holder. ThO2 and UO2 single crystal specimens were grown inside an inert silver ampoule using hydrothermal synthesis. Both samples were irradiated using 2 MeV protons at 600oC up to 0.1 dpa at Texas A&M University’s Accelerator Laboratory. Fig. 1a shows a weak-beam dark field TEM image of ThO2 after irradiation, indicating the presence of faulted 1/3 <111> type dislocation loops. This presentation will discuss the effect of annealing temperature (600oC, 800oC, 1000oC, 1100oC, etc.) on dislocation loop density, size and distribution, loop nature (interstitial/vacancies) and Burgers vector, as well as the formation of voids in both ThO2 and UO2. This work will also discuss the interaction between defects during annealing. The in-situ TEM annealing cycle is shown in Fig 1b. This research significantly improves the understanding of defect behavior in oxide nuclear fuels with temperature and will aid computational modeling efforts. This work was supported as part of the Center for Thermal Energy Transport under Irradiation (TETI) Energy Frontier Research Center, funded by the U.S. Department of Energy Office of Science.

36 MATERIALS SCIENCE↗
DOE OSTI2025

On the bulk compaction of brittle granular materials, part I: SeS analysis of axial compression to 4000 MPa

The bulk compaction of granular materials has been studied for decades to interpret and manage responses for soils and powder-based component fabrication, and geophysical, celestial, and ballistic impact. Their bulk or macroscopic compaction response is limited by what occurs at the granular or microstructural scale. Motivation existed to more closely examine that association specific to granular brittle materials (e.g., ceramics and glasses). That examination is offered in a series of three companion papers where Part I describes a new supplemental analysis adopted to bulk compaction response involving relatively high compaction stresses (4000 MPa). Bulk compactions of vitreous silicates and crystalline quartzes were interpreted in three ways, including that of a new analysis that considers the product of void ratio (e) and stress (S) as a function of S, hereafter referred to as “SeS analysis”. In conclusion, the SeS analysis was found to be an informative supplement to conventional bulk compaction analyses because it provides more consistent higher sensitivity for the identification of bulk density rate increase with increasing compaction (softening); a rate increase that arises from the cumulative effect of the onsets and progression of compaction-induced yielding, fracture or comminution, densification, phase change, or combinations thereof occurring at the granular or microstructural scale.

compaction↗
DOE OSTI2022

Simulation of CEFR neutronic start-up tests with FENNECS

This paper presents simulation results of selected Neutronic Start-up Tests of the China Experimental Fast Reactor (CEFR) obtained by the neutronics code FENNECS that have been performed within the frame of the IAEA Coordinated Research Program I31032. The Finite Element Neutronics code FENNECS is developed at GRS and solves the few-group steady-state and transient diffusion equation using a Galerkin-based finite element approach. Its main purpose is the safety assessment of Small Modular Reactors and Micro Reactors with complex geometry (e.g., rotating control drums) which gain increased interest internationally. Serpent has been applied to create reference models of the CEFR and cross-section libraries in 10 energy groups for FENNECS. Using these libraries, the following experiments have been simulated with FENNECS: net criticality, control rod integral and differential worth, void reactivity effect, subassembly exchange reactivity effects and reaction rate distribution. The obtained satisfactory agreements with the measurements represent a valuable contribution to the validation of FENNECS. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Comprehensive compilations of computation results and validations for neutronics start-up tests at China Experimental Fast Reactor

This paper compiles and analyzes refined results of the coordinated research project (CRP) on Neutronics Benchmark of China Experimental Fast Reactor (CEFR) Start-Up Tests conducted by the International Atomic Energy Agency (IAEA) since 2018. Twenty-eight research organizations participated with various code systems. The China Institute of Atomic Energy (CIAE) provided the benchmark specifications and participants conducted the benchmark through blind and refined phases. This paper presents the benchmark results on six experimental measurements, criticality, control rod worth, temperature reactivity coefficients, sodium void worth, assembly swap reactivities, and foil activations. Except for a few outlier results, the simulation results show good agreement with the measured data within 1-σ experiment uncertainties. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗