Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Turbulence modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

CFD Sensitivity Analysis of a Modern Civil Transport Near Buffet-Onset Conditions

A computational fluid dynamics (CFD) sensitivity analysis is conducted for a modern civil transport at several conditions ranging from mostly attached flow to flow with substantial separation. Two different Navier-Stokes computer codes and four different turbulence models are utilized, and results are compared both to wind tunnel data at flight Reynolds number and flight data. In-depth CFD sensitivities to grid, code, spatial differencing method, aeroelastic shape, and turbulence model are described for conditions near buffet onset (a condition at which significant separation exists). In summary, given a grid of sufficient density for a given aeroelastic wing shape, the combined approximate error band in CFD at conditions near buffet onset due to code, spatial differencing method, and turbulence model is: 6% in lift, 7% in drag, and 16% in moment. The biggest two contributers to this uncertainty are turbulence model and code. Computed results agree well with wind tunnel surface pressure measurements both for an overspeed 'cruise' case as well as a case with small trailing edge separation. At and beyond buffet onset, computed results agree well over the inner half of the wing, but shock location is predicted too far aft at some of the outboard stations. Lift, drag, and moment curves are predicted in good agreement with experimental results from the wind tunnel.

Rumsey, Christopher L.↗
NASA NTRS2006

Implementation of Flow Tripping Capability in the USM3D Unstructured Flow Solver

A flow tripping capability is added to an established NASA tetrahedral unstructured parallel Navier-Stokes flow solver, USM3D. The capability is based on prescribing an appropriate profile of turbulence model variables to energize the boundary layer in a plane normal to a specified trip region on the body surface. We demonstrate this approach using the k-e two-equation turbulence model of USM3D. Modification to the solution procedure primarily consists of developing a data structure to identify all unstructured tetrahedral grid cells located in the plane normal to a specified surface trip region and computing a function based on the mean flow solution to specify the modified profile of the turbulence model variables. We leverage this data structure and also show an adjunct approach that is based on enforcing a laminar flow condition on the otherwise fully turbulent flow solution in user specified region. The latter approach is applied for the solutions obtained using other one- and two-equation turbulence models of USM3D. A key ingredient of the present capability is the use of a graphical user-interface tool PREDISC to define a trip region on the body surface in an existing grid. Verification of the present modifications is demonstrated on three cases, namely, a flat plate, the RAE2822 airfoil, and the DLR F6 wing-fuselage configuration.

Pandya, Mohagna J.↗
NASA NTRS2006

Implementation of Flow Tripping Capability in the USM3D Unstructured Flow Solver

A flow tripping capability is added to an established NASA tetrahedral unstructured parallel Navier-Stokes flow solver, USM3D. The capability is based on prescribing an appropriate profile of turbulence model variables to energize the boundary layer in a plane normal to a specified trip region on the body surface. We demonstrate this approach using the k-epsilon two-equation turbulence model of USM3D. Modification to the solution procedure primarily consists of developing a data structure to identify all unstructured tetrahedral grid cells located in the plane normal to a specified surface trip region and computing a function based on the mean flow solution to specify the modified profile of the turbulence model variables. We leverage this data structure and also show an adjunct approach that is based on enforcing a laminar flow condition on the otherwise fully turbulent flow solution in user-specified region. The latter approach is applied for the solutions obtained using other one-and two-equation turbulence models of USM3D. A key ingredient of the present capability is the use of a graphical user-interface tool PREDISC to define a trip region on the body surface in an existing grid. Verification of the present modifications is demonstrated on three cases, namely, a flat plate, the RAE2822 airfoil, and the DLR F6 wing-fuselage configuration.

Pandya, Mohagna J.↗
NASA NTRS2003

CFD Variability for a Civil Transport Aircraft Near Buffet-Onset Conditions

A CFD sensitivity analysis is conducted for an aircraft at several conditions, including flow with substantial separation (buffet onset). The sensitivity is studied using two different Navier-Stokes computer codes, three different turbulence models, and two different grid treatments of the wing trailing edge. This effort is a follow-on to an earlier study of CFD variation over a different aircraft in buffet onset conditions. Similar to the earlier study, the turbulence model is found to have the largest effect, with a variation of 3.8% in lift at the buffet onset angle of attack. Drag and moment variation are 2.9% and 23.6%, respectively. The variations due to code and trailing edge cap grid are smaller than that due to turbulence model. Overall, the combined approximate error band in CFD due to code, turbulence model, and trailing edge treatment at the buffet onset angle of attack are: 4% in lift, 3% in drag, and 31% in moment. The CFD results show similar trends to flight test data, but also exhibit a lift curve break not seen in the data.

Rumsey, Christopher L.↗
NASA NTRS2016

Reynolds-Stress and Triple-Product Models Applied to a Flow with Rotation and Curvature

Turbulence models, with increasing complexity, up to triple product terms, are applied to the flow in a rotating pipe. The rotating pipe is a challenging case for turbulence models as it contains significant rotational and curvature effects. The flow field starts with the classic fully developed pipe flow, with a stationary pipe wall. This well defined condition is then subjected to a section of pipe with a rotating wall. The rotating wall introduces a second velocity scale, and creates Reynolds shear stresses in the radial-circumferential and circumferential-axial planes. Furthermore, the wall rotation introduces a flow stabilization, and actually reduces the turbulent kinetic energy as the flow moves along the rotating wall section. It is shown in the present work that the Reynolds stress models are capable of predicting significant reduction in the turbulent kinetic energy, but triple product improves the predictions of the centerline turbulent kinetic energy, which is governed by convection, dissipation and transport terms, as the production terms vanish on the pipe axis.

Turbulence models↗
NASA NTRS1985

Multiple-scale turbulence closure modeling of confined recirculating flows

A multiple-scale turbulence closure scheme is developed for the numerical predictions of confined recirculating flows. This model is based on the multiple-time-scale concepts of Hanjalic et al. (1980) and takes into account the non-equilibrium spectra energy transfer mechanism. Problems concerning new formulation of energy transfer rate equations and subsequent model coefficient redefinition and energy spectrum partition are discussed. Comparisons are made with several experiments of internal recirculating flows for the purpose of model validation. Numerical results using the present model show significant improvement of predictive capability over that obtained with the single-scale k-epsilon model and show promising potential for complex turbulent flow predictions.

Chen, C. P.↗
NASA NTRS1994

Roles of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer

This study focuses on the effects of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer. When the simulated drizzle rate is relatively small (maximum approximately equal to 0.6 mm/day), steady-state solutions are obtained. The boundary layer stabilizes essentially because drizzle causes evaporative cooling of the subcloud layer. This stabilization considerably reduces the buoyancy flux and turbulence kinetic energy below the stratus cloud. Thus, drizzle tends to decouple the cloud from the subcloud layer in the model, as suggested by many observational studies. In addition, the evaporation of drizzle in the subcloud layer creates small scattered clouds, which are likely to represent cumulus clouds, below the solid stratus cloud in the model. The sensitivity experiments show that these scattered clouds help maintain a coupled boundary layer. When the drizzle rate is relatively large (maximum approximately equal to 0.9 mm/day), the response of the model becomes transient with bursts in turbulent fluxes. This phenomenon is related to the formation of the scattered cloud layer below the solid stratus cloud. It appears that the model is inadequate to represent the heat and moisture transport by strong updrafts covering a small fractional area in cumulus convection.

Wang, Shouping↗
NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: 1) a k-epsilon turbulence model computation on a 6.8 million point grid using wall functions, 2) a k-epsilon turbulence model computation on a 14 million point grid integrating to the wall, and 3) a k-omega turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-epsilon and k-omega computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-epsilon computations which extended from 70% to 100% span at the exit rating plane, whereas the k-omega computation had reversed flow from 95% to 100% span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-epsilon case resulted in an under-prediction in adiabatic efficiency of 8.3 points, whereas the k-omega case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗
NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: (1) a k-ε turbulence model computation on a 6.8 million point grid using wall functions, (2) a k-ε turbulence model computation on a 14 million point grid integrating to the wall, and (3) a k-ω turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-ε and k-ω computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-ε computations which extended from 70 to 100 percent span at the exit rating plane, whereas the k-ω computation had reversed flow from 95 to 100 percent span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-ε case resulted in an underprediction in adiabatic efficiency of 8.3 points, whereas the k-ω case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗
NASA NTRS1983

Numerical simulation of turbulent trailing edge flows

Numerical simulations of the time-dependent, Reynolds-averaged, Navier-Stokes equations, employing a two-equation turbulence model, are presented and compared with measurements from a series of trailing edge experiments at transonic Mach numbers. The test flows include an asymmetric flow with no separation, an asymmetric flow with a small region of separation and a symmetric flow with a large shock-wave induced separated zone. Comparisons are made for mean surface quantities as well as for mean and fluctuating flow-field quantities. For the trailing-edge flows with little or no separation, the solutions correctly predict all the major features of the flow field. Treatment of the viscous-inviscid interaction was found to be important for predicting these test cases. Two-equation eddy-viscosity turbulence models were found to be adequate for these flows. However, for the shock-wave induced separation case, these turbulence models were inadequate to predict this flow field. Modifications of the turbulence model to correct these deficiencies are discussed.

Horstman, C. C.↗
NASA NTRS1998

Prediction of Very High Reynolds Number Compressible Skin Friction

Flat plate skin friction calculations over a range of Mach numbers from 0.4 to 3.5 at Reynolds numbers from 16 million to 492 million using a Navier Stokes method with advanced turbulence modeling are compared with incompressible skin friction coefficient correlations. The semi-empirical correlation theories of van Driest; Cope; Winkler and Cha; and Sommer and Short T' are used to transform the predicted skin friction coefficients of solutions using two algebraic Reynolds stress turbulence models in the Navier-Stokes method PAB3D. In general, the predicted skin friction coefficients scaled well with each reference temperature theory though, overall the theory by Sommer and Short appeared to best collapse the predicted coefficients. At the lower Reynolds number 3 to 30 million, both the Girimaji and Shih, Zhu and Lumley turbulence models predicted skin-friction coefficients within 2% of the semi-empirical correlation skin friction coefficients. At the higher Reynolds numbers of 100 to 500 million, the turbulence models by Shih, Zhu and Lumley and Girimaji predicted coefficients that were 6% less and 10% greater, respectively, than the semi-empirical coefficients.

Carlson, John R.↗
NASA NTRSDate not supplied

Transition Prediction for the 30P30N Airfoil and the CRM-HL using FUN3D

The ability to accurately model transition over high-lift configurations can lead to improved agreement between stationary Reynolds-Averaged Navier-Stokes (RANS) computations and experimental measurements. In this work, selected transport-equation-based RANS models for transition prediction in the NASA FUN3D flow solver are used to simulate flow over the 30P30N three-element airfoil and the High-Lift Common Research Model (CRM-HL). The primary RANS-based transition model is the Langtry-Menter (LM) 𝜸-Re𝜽𝒕 model coupled with the Menter shear-stress transport model. Additionally, the existing capability for transition prediction based on linear stability correlations is used to allow the modeling of transition over multiple elements of the 30P30N configuration. This approach pairs an algebraic transition model with the Spalart-Allmaras (SA) turbulence model that relies on an imposed transition location in FUN3D and the parabolized stability equations as implemented in the LASTRAC code. Predictions based on these different transition prediction approaches and models are compared with each other, experimental data, and previous simulations by evaluating the lift and drag coefficients, the surface-pressure/skin-friction distributions, and the locations of transition onset. Results are presented for multiple angles of attack for the 30P30N airfoil and CRM-HL. For the CRM-HL, a grid resolution study is performed for the LM transition model and the SA turbulence model.

High Lift↗
NASA NTRS1993

Computational analysis of hypersonic shock wave/wall jet interaction

The purpose of this study is to investigate the CFD code General Aerodynamic Simulation Program (GASP) for application to a specific scramjet combustor phenomenon, that of an adverse pressure gradient caused by an oblique shock wave impinging upon a wall cooling film. The basis of this investigation is data available from an existing experimental study, which includes wall pressure, wall heat transfer, and schlieren photographs. This experimental study was conducted at a nominal Mach number of 6.0 in the Calspan 48-inch shock tunnel. The particular case of interest generates flow separation at the shock impingement point. Two algebraic turbulence models, the Baldwin-Lomax model and the Goldberg model, are considered for this computational study. Resultant computational wall pressure and heat transfer for both turbulence models are compared with experimental data. The Goldberg turbulence model provides a more accurate prediction of the recirculation region, and as a result, a better comparison with the experimental data.

Mekkes, Gregory L.↗
DOE OSTI2022

Multicomponent gas mixture parametric CFD study of condensation heat transfer in small modular reactor system safety

Safety is always the primary concern for designing and analyzing nuclear reactor systems. The requirements for the safety margin for advanced small modular reactor (SMR) systems are targeted even higher than the conventional commercial large-scale nuclear reactors incorporating the passive and inherent safety systems. The SMR systems are designed with the condensation passive containment cooling system (PCCS), which plays a critical role in removing reactor heat during a steam release accident case. However, the presence of non-condensable gas (NCG), like air, reduces the heat transfer performance. This physics phenomenon becomes multifactorial for nuclear reactor containment during a fuel failure accident case that releases hydrogen gas. Besides, the mixture component of steam-air-hydrogen varies in reactor accident cases, which need simulation and validation keeping parameters of importance. Reviews showed that previous studies for SMR’s PCCCS did not cover the condensation heat transfer (CHT) in the presence of multicomponent NCG mixture parametric computational fluid dynamics (CFD) simulation and validation, making a research gap in the SMR design safety. A comprehensive CHT parametric CFD study was performed for SMR PCCS to fill this research gap. This study used experimental data as simulation 3D physics domain inlet and outlet boundary conditions. However, the wall boundary conditions were constant temperature, curve-fit, and annular coolant for verifying the turbulence models. Parametric simulations were performed, verified, and optimized for steam-NCGs mixtures. The multicomponent gases, multiphase mixtures, and fluid film condensation models were applied with associated turbulence models. The results of the parametric study were evaluated for realistic reactor conditions. Results showed that parametric study provided critical insight about the dependency of multicomponent gas mixture parameters that supports reactor safety design, analysis, and licensing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1988

Computational simulation of turbulent flow in Space Shuttle Main Engine turnaround ducts

Two axisymmetric 180-deg turnaround ducts are used in the Space Shuttle Main Engine (SSME) to connnect the preburners with the main thrust chamber. The prediction of the flow field and heat transfer within the turnaround ducts is important to minimize the pressure drops, size of recirculation and stagnation zones, local overheating, etc. This paper presents the computational approach and selected results for the turbulent flow in the turnaround ducts of the fuel and oxidizer sides of the SSME. The time-averaged, Navier-Stokes equations for the viscous, compressible, turbulent flow are solved in body-fitted-coordinates by using a finite-volume approach. Two turbulence models, viz: the k-epsilon model and a multiple scale turbulence model, are used to examine the sensitivity of calculated flows. Both models produce almost identical solutions for the fuelside turnaround duct (which has no recirculation region). However, for the oxidizer-side duct which has a large recirculation region, the two models show quite different results.

Przekwas, Andrzej J.↗
NASA NTRS1996

Calculation of Turbulent Subsonic Diffuser Flows Using the NPARC Navier-Stokes Code

Axisymmetric subsonic diffuser flows were calculated with the NPARC Navier-Stokes code in order to determine the effects various code features have on the flow solutions. The code features examined in this work were turbulence models and boundary conditions. Four turbulence models available in NPARC were used: the Baldwin-Lomax algebraic model, the Baldwin-Barth one-equation model, and the Chien kappa-epsilon and Wilcox kappa-omega two-equation models. The three boundary conditions examined were the free boundary, the mass flux boundary and the subsonic outflow with variable static pressure. In addition to boundary condition type, the geometry downstream of the diffuser was varied to see if upstream influences were present. The NPARC results are compared with experimental data and recommendations are given for using NPARC to compute similar flows.

Dudek, J. C.↗
NASA NTRS2003

Study of Unsteady Flows with Concave Wall Effect

This paper presents computational fluid dynamic studies of the inlet turbulence and wall curvature effects on the flow steadiness at near wall surface locations in boundary layer flows. The time-stepping RANS numerical solver of the NASA Glenn-HT RANS code and a one-equation turbulence model, with a uniform inlet turbulence modeling level of the order of 10 percent of molecular viscosity, were used to perform the numerical computations. The approach was first calibrated for its predictabilities of friction factor, velocity, and temperature at near surface locations within a transitional boundary layer over concave wall. The approach was then used to predict the velocity and friction factor variations in a boundary layer recovering from concave curvature. As time iteration proceeded in the computations, the computed friction factors converged to their values from existing experiments. The computed friction factors, velocity, and static temperatures at near wall surface locations oscillated periodically in terms of time iteration steps and physical locations along the span-wise direction. At the upstream stations, the relationship among the normal and tangential velocities showed vortices effects on the velocity variations. Coherent vortices effect on the velocity components broke down at downstream stations. The computations also predicted the vortices effects on the velocity variations within a boundary layer flow developed along a concave wall surface with a downstream recovery flat wall surface. It was concluded that the computational approach might have the potential to analyze the flow steadiness in a turbine blade flow.

Wang, Chi R.↗