Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Trajectory Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Optimal plane change by low aerodynamic forces

This paper presents the exact dimensionless equations of motion and the necessary conditions for the computation of the optimal trajectories of a hypervelocity vehicle flying through a nonrotating spherical planetary atmosphere. It is shown that there are two types of maneuvers with nearly identical plane change. In the hard maneuver, the vehicle is pulled down to low altitude for aerodyamic plane change before exit at the prescribed final speed. In the slow maneuver which is described in detail in this paper, the vehicle remains in orbital flight with a small incremental plane change during each passage through the perigee. This maneuver requires several revolutions, and the technique for computation is similar to that in the problem of contraction of orbit.

Vinh, Nguyen X.↗
NASA NTRS1990

Wind shear procedures and the instrumentation

The effect of pitch rate on abort landing caused by wind shear encounters is discussed. Optimal trajectories, airspeed, and wind shear warning systems are briefly discussed. The bulk of the presentation is in viewgraph form.

Melvin, W. W.↗
NASA NTRS1991

Range optimization for a supersonic aircraft

Range optimal trajectories for an aircraft flying in the vertical plane are obtained from Pontryagin's Minimum Principle. Control variables are load factor n which appears nonlinearly in the equations of motion and throttle setting eta, which appears only linearly. Both controls are subject to fixed bounds, namely eta between values of 0 and 1 and absolute value of n not greater than n(max). Additionally, a dynamic pressure limit is imposed, which represents a first-order state-inequality constraint. For fixed flight time, fixed initial coordinates, and partially fixed final coordinates, the effect of the load factor limit absolute value of n not greater than n(max) is studied. Upon varying n(max), six different switching structures are obtained. All trajectories involve singular control along arcs with active dynamic pressure limit.

Seywald, Hans↗
NASA NTRS1991

A minimum propellant solution to an orbit-to-orbit transfer using a low thrust propulsion system

The Space Exploration Initiative is considering the use of low thrust (nuclear electric, solar electric) and intermediate thrust (nuclear thermal) propulsion systems for transfer to Mars and back. Due to the duration of such a mission, a low thrust minimum-fuel solution is of interest; a savings of fuel can be substantial if the propulsion system is allowed to be turned off and back on. This switching of the propulsion system helps distinguish the minimal-fuel problem from the well-known minimum-time problem. Optimal orbit transfers are also of interest to the development of a guidance system for orbital maneuvering vehicles which will be needed, for example, to deliver cargoes to the Space Station Freedom. The problem of optimizing trajectories for an orbit-to-orbit transfer with minimum-fuel expenditure using a low thrust propulsion system is addressed.

Cobb, Shannon S.↗
NASA NTRS1992

System controls challenges of hypersonic combined-cycle engine powered vehicles

Hypersonic aircraft with air-breathing engines have been described as the most complex and challenging air/space vehicle designs ever attempted. This is particularly true for aircraft designed to accelerate to orbital velocities. The propulsion system for the National Aerospace Plane will be an active factor in maintaining the aircraft on course. Typically addressed are the difficulties with the aerodynamic vehicle design and development, materials limitations and propulsion performance. The propulsion control system requires equal materials limitations and propulsion performance. The propulsion control system requires equal concern. Far more important than merely a subset of propulsion performance, the propulsion control system resides at the crossroads of trajectory optimization, engine static performance, and vehicle-engine configuration optimization. To date, solutions at these crossroads are multidisciplinary and generally lag behind the broader performance issues. Just how daunting these demands will be is suggested. A somewhat simplified treatment of the behavioral characteristics of hypersonic aircraft and the issues associated with their air-breathing propulsion control system design are presented.

Morrison, Russell H.↗
NASA NTRS1992

Joint Japan/U.S. Conference on Adaptive Structures, 2nd, Nagoya, Japan, Nov. 12-14, 1991, Collection of Papers

The present conference discusses the development status of adaptive structures in Europe and in Japan, the 'Cosmo-Lab' structures/robotics cooperation concept, active-adhesion concepts for in-orbit structural assembly, adaptively controlled truss structures, object-oriented modeling in structural analysis, the control effectiveness and energy efficiency of an active mass damper, a space truss with experimental tendon control, and piezoelectric actuator-based space trusses. Also discussed is the control of resonant frequencies in adaptive structures through prestressing, active control of vortex-excited vibrations of flexible cylindrical structures, shape adjustment of a flexible space antenna reflector, the SDIO Adaptive Structures Program, optimal trajectories of iterative manipulation for space robots, a docking device as an adaptive structure, shape-memory polymers and their hybrid composites, and fuzzy control methods for structural dynamics.

Matsuzaki, Yuji↗
NASA NTRS1993

Investigation of the launch pad abort capabilities of the HL-20 lifting body

The capability of the HL-20 lifting body spacecraft to perform an abort maneuver from the launch pad to a horizontal landing was studied at NASA Langley Research Center. This study involved both piloted and batch simulation models of the vehicle. A point-mass model of the vehicle was used for trajectory optimization studies. The piloted simulation was performed in the Visual Motion Simulator in fixed-base mode. A candidate maneuver was developed and refined for the worst-case launch-pad-to-landing-site geometry using an iterative procedure of off-line maneuver analysis followed by piloted evaluations and heuristic improvements to the candidate maneuver. The resulting maneuver demonstrates the launch site abort capability of the HL-20 and dictates requirements for nominal abort motor performance. The sensitivity of the maneuver to variations in several design parameters was documented.

Jackson, E. B.↗
NASA NTRS1993

Minimum-fuel trajectories for hypersonic vehicles with aeropropulsive interactions

The class of hypersonic vehicle configurations with single stage-to-orbit (SSTO) capability reflect highly integrated airframe and propulsion systems. These designs are also known to exhibit a large degree of interaction between the airframe and engine dynamics. Consequently, even simplified hypersonic models are characterized by tightly coupled nonlinear equations of motion. It is to be determined how these features, along with the stringent mission requirements placed on the vehicle, affect its trajectory performance. In this paper, a trajectory optimization problem for a generic hypersonic lifting body will be formulated, a solution method outlined, and results presented. The solution sought is a minimum-fuel trajectorv for orbit injection. It is also desired to study the effect of heating constraints on the vehicle.

Lovell, T. A.↗
NASA NTRS1993

Robust neighboring extremal guidance for the advanced launch system

With the availability of modern flight computers, realtime neighboring extremal guidance seems feasible. To overcome sensitivity to unknown system parameters and environmental uncertainties, a robust neighboring extremal guidance scheme is proposed. About the optimal trajectory, the accessory problem in the calculus of variations is formed, generating a quadratic cost criterion in the perturbed states and controls. By formulating a disturbance attenuation problem based upon the second variation cost criterion, a differential game is formulated. The game theoretic cost criterion is minimized with respect to the perturbed control but maximized with respect to the unknown parameters in the linearized dynamics. The resulting differential game problem gives rise to a two-point boundary-value problem solved using the sweep method. The sweep method solution provides a linear robust neighboring extremal guidance scheme that is applied to the Advanced Launch System.

Bain, John↗
NASA NTRS1988

The Apollo Lightcraft Project

The overall goal for this NASA/USRA-sponsored 'Apollo Lightcraft Project' is to develop a revolutionary launch vehicle technology that can reduce payload transport costs by a factor of 1000 below the Space Shuttle Orbiter. The RPI design team proposes to utilize advanced, highly energetic, beamed-energy sources (laser, microwave) and innovative combined-cycle (airbreathing/rocket) engines to accomplish this goal. This second year focused on systems integration and analysis of the 'Apollo Lightcraft'. This beam-powered, single-stage-to-orbit vehicle is envisioned as the globe-trotting family shuttlecraft of the 21st century. Detailed investigations of the Apollo Lightcraft Project during the second year of study helped evolve the propulsion system design, while focusing on the following areas: (1) man/machine interface; (2) flight control systems; (3) power beaming system architecture; (4) reentry aerodynamics; (5) shroud structural dynamics; and (6) optimal trajectory analysis.

Source record↗
NASA NTRS1989

Aerodynamic control, recovery, and sensor design for a first stage flyback booster

The mission of the flyback group is to control and recover the first stage of a commercially developed winged booster launched from a B-52 at 40,000 ft and Mach 0.8. First-stage separation occurs at 210,000 ft and Mach 8.7; the second and third stages will continue deployment of their 600 lb payload into low Earth orbit. The job of the flyback group begins at this point, employing a modified control system developed to stabilize and maneuver the separated first-stage vehicle to a suitable landing site approximately 130 miles from the launch point over the Pacific Ocean. This multidisciplinary design was accomplished by four subgroups: aerodynamic design/vehicle configuration (ADVC), trajectory optimization, controls, and thermal management.

Source record↗
NASA NTRS1994

Launch-pad abort capabilities of the HL-20 lifting body

The capability of the HL-20 lifting body to perform an abort maneuver from the launch pad to a horizontal landing was studied. The study involved both piloted and batch simulation models of the vehicle. A point-mass model of the vehicle was used for trajectory optimization studies. The piloted simulation was performed in the Langley Visual/Motion Simulator in the fixed-base mode. A candidate maneuver was developed and refined for the worst-case launch-pad-to-landing-site geometry with an iterative procedure of off-line maneuver analysis followed by piloted evaluations and heuristic improvements to the candidate maneuver. The resulting maneuver demonstrates the launch-site abort capability of the HL-20 and dictates requirements for nominal abort-motor performance. The sensitivity of the maneuver to variations in several design parameters was documented.

Jackson, E. Bruce↗
NASA NTRS1994

A simple analytical aerodynamic model of Langley Winged-Cone Aerospace Plane concept

A simple three DOF analytical aerodynamic model of the Langley Winged-Coned Aerospace Plane concept is presented in a form suitable for simulation, trajectory optimization, and guidance and control studies. The analytical model is especially suitable for methods based on variational calculus. Analytical expressions are presented for lift, drag, and pitching moment coefficients from subsonic to hypersonic Mach numbers and angles of attack up to +/- 20 deg. This analytical model has break points at Mach numbers of 1.0, 1.4, 4.0, and 6.0. Across these Mach number break points, the lift, drag, and pitching moment coefficients are made continuous but their derivatives are not. There are no break points in angle of attack. The effect of control surface deflection is not considered. The present analytical model compares well with the APAS calculations and wind tunnel test data for most angles of attack and Mach numbers.

Pamadi, Bandu N.↗
NASA NTRS1995

Advanced methods of structural and trajectory analysis for transport aircraft

This report summarizes the efforts in two areas: (1) development of advanced methods of structural weight estimation, and (2) development of advanced methods of trajectory optimization. The majority of the effort was spent in the structural weight area. A draft of 'Analytical Fuselage and Wing Weight Estimation of Transport Aircraft', resulting from this research, is included as an appendix.

Ardema, Mark D.↗
NASA NTRS2000

The Mathematics of Navigating the Solar System

In navigating spacecraft throughout the solar system, the space navigator relies on three academic disciplines - optimization, estimation, and control - that work on mathematical models of the real world. Thus, the navigator determines the flight path that will consume propellant and other resources in an efficient manner, determines where the craft is and predicts where it will go, and transfers it onto the optimal trajectory that meets operational and mission constraints. Mission requirements, for example, demand that observational measurements be made with sufficient precision that relativity must be modeled in collecting and fitting (the estimation process) the data, and propagating the trajectory. Thousands of parameters are now determined in near real-time to model the gravitational forces acting on a spacecraft in the vicinity of an irregularly shaped body. Completing these tasks requires mathematical models, analyses, and processing techniques. Newton, Gauss, Lambert, Legendre, and others are justly famous for their contributions to the mathematics of these tasks. More recently, graduate students participated in research to update the gravity model of the Saturnian system, including higher order gravity harmonics, tidal effects, and the influence of the rings. This investigation was conducted for the Cassini project to incorporate new trajectory modeling features in the navigation software. The resulting trajectory model will be used in navigating the 4-year tour of the Saturnian satellites. Also, undergraduate students are determining the ephemerides (locations versus time) of asteroids that will be used as reference objects in navigating the New Millennium's Deep Space 1 spacecraft autonomously.

Hintz, Gerald↗
NASA NTRS2002

Intelligent Pilot Aids for Flight Re-Planning in Emergencies

Experimental studies were conducted with pilots to investigate the attributes of automation that would be appropriate for aiding pilots in emergencies. The specific focus of this year was on methods of mitigating automation brittleness. Brittleness occurs when the automatic system is used in circumstances it was not designed for, causing it to choose an incorrect action or make an inaccurate decision for the situation. Brittleness is impossible to avoid since it is impossible to predict every potential situation the automatic system will be exposed to over its life. However, operators are always ultimately responsible for the actions and decisions of the automation they are monitoring or using, which means they must evaluate the automation's decisions and actions for accuracy. As has been pointed out, this is a difficult thing for human operators to do. There have been various suggestions as to how to aid operators with this evaluation. In the study described in this report we studied how presentation of contextual information about an automatic system's decision might impact the ability of the human operators to evaluate that decision. This study focused on the planning of emergency descents. Fortunately, emergencies (e.g., mechanical or electrical malfunction, on-board fire, and medical emergency) happen quite rarely. However, they can be catastrophic when they do. For all predictable or conceivable emergencies, pilots have emergency procedures that they are trained on, but those procedures often end with 'determine suitable airport and land as quickly as possible.' Planning an emergency descent to an unplanned airport is a difficult task, particularly under the time pressures of an emergency. Automatic decision aids could be very efficient at the task of determining an appropriate airport and calculating an optimal trajectory to that airport. This information could be conveyed to the pilot through an emergency descent procedure listing all of the actions necessary to safely land the plane. However, there is still the potential problem of brittleness. This study examined the impact of contextual information in presentations of emergency descent procedures to see if they might impact the pilot's evaluation of the feasibility of the presented procedure. The study and its results are described in detail.

Pritchett, Amy R.↗
NASA NTRS2001

Making the EZ Choice

Analytical Mechanics Associates, Inc. (AMA), of Hampton, Virginia, created the EZopt software application through Small Business Innovation Research (SBIR) funding from NASA's Langley Research Center. The new software is a user-friendly tool kit that provides quick and logical solutions to complex optimal control problems. In its most basic form, EZopt converts process data into math equations and then proceeds to utilize those equations to solve problems within control systems. EZopt successfully proved its advantage when applied to short-term mission planning and onboard flight computer implementation. The technology has also solved multiple real-life engineering problems faced in numerous commercial operations. For instance, mechanical engineers use EZopt to solve control problems with robots, while chemical plants implement the application to overcome situations with batch reactors and temperature control. In the emerging field of commercial aerospace, EZopt is able to optimize trajectories for launch vehicles and perform potential space station- keeping tasks. Furthermore, the software also helps control electromagnetic devices in the automotive industry.

Source record↗