Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TAPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Static structural tests of a 1.5-meter diameter fabric attached inflatable decelerator

Meridional tape forces, permeability, and change in model contours were measured on the aft half of a 1.5-m-diameter attached inflatable decelerator (AID). Inflation pressures up to 103 kN per square meter and external pressures of 0.14 to 102 kN per square meter were used. The results indicated that the model stresses were near the desired isotensoid condition. Future AID designs should consider both stiffness and strength of the meridional tapes to obtain the optimum division of load between tapes and fabric. Permeability of pressurized fabric structures is a few orders of magnitude higher than that obtained in the standard low-pressure test on material specimens.

Willis, C. M.↗
NASA NTRS1972

Mariner Mars 1971 data storage subsystem

A digital tape recorder was used on the Mariner Mars 1971 spacecraft to record television and scientific data. Data were recorded at 132 kilobits/sec and were reproduced at one of five available rates (16.2, 8.1, 4.05, 2.05, or 1.0125 kilobits/sec) selected by ground command to be congruous with the spacecraft-to-earth communications link performance. The transport mechanism contained 167 m of 1.2 cm magnetic recording tape. A single motor was used to drive the peripheral drive transport. During development of the design, stick slip problems were encountered. A design life of 2400 tape passes was achieved during the mission.

Grumm, R.↗
NASA NTRS1972

A dynamic response and eye scanning data base useful in the development of theories and methods for the description of control/display relationships

A set of specially prepared digital tapes is reported which contain synchronized measurements of pilot scanning behavior, control response, and vehicle response obtained during instrument landing system approaches made in a fixed-base DC-8 transport simulator. The objective of the master tape is to provide a common data base which can be used by the research community to test theories, models, and methods for describing and analyzing control/display relations and interactions. The experimental conditions and tasks used to obtain the data and the detailed format of the tapes are described. Conventional instrument panel and controls were used, with simulated vertical gust and glide slope beam bend forcing functions. Continuous pilot eye fixations and scan traffic on the panel were measured. Both flight director and standard localizer/glide slope types of approaches were made, with both fixed and variable instrument range sensitivities.

Klein, R.↗
NASA NTRS1973

System description and operating guide for DSAS illumination and moon conflict programs

The DSAS Illumination and Moon Conflict programs are described which during an orbit when the DSAS (Digital Solar Aspect Sensor) will record the direct rays of the sun, and the periods of time when the horizon scanners will come in conflict with the moon. The DSAS Illumination Program makes use of an orbit tape (or epoch time and orbital elements) in addition to an ephemeris tape containing positions of the sun and moon. The Moon Conflict Program makes use of the same ephemeris tape with sun and moon positions, but uses only epoch time and orbital elements for the satellite positions. These programs were designed for the TIROS or ITOS series spacecraft but may be utilized by any spacecraft with similar sensors.

Dunker, S. C.↗
NASA NTRS1973

Celescope catalog of ultraviolet stellar observations: 5068 objects measured by Orbiting Astronomical Observatory (OAO-2)

During the 16 months that the Celescope Experiment operated, it took 8000 frames of data. This report describes the experiment, the data it gathered, the format of the magnetic tape containing the data, and a number of programs that were written to read and manipulate the tape. The tape version of the catalog contains Data on 5068 stars and is available from the National Space Sciences Data Center.

Davis, R. J.↗
NASA NTRS1973

Digital data detection and synchronization

The primary accomplishments have been in the analysis and simulation of receivers and bit synchronizers. It has been discovered that tracking rate effects play, a rather fundamental role in both receiver and synchronizer performance, but that data relating to recorder time-base-error, for the proper characterization of this phenomenon, is in rather short supply. It is possible to obtain operationally useful tape recorder time-base-error data from high signal-to-noise ratio tapes using synchronizers with relatively wideband tracking loops. Low signal-to-noise ratio tapes examined in the same way would not be synchronizable. Additional areas of interest covered are receiver false lock, cycle slipping, and other unusual phenomena, which have been described to some extent in this and earlier reports and simulated during the study.

Noack, T. L.↗
NASA NTRS1974

Skylab 2 ground winds data reduction and statistical analysis

A ground winds test was conducted on the Skylab 2 spacecraft in a subsonic wind tunnel and the results were tape recorded for analysis. The data reduction system used to analyze the tapes for full scale, first and second mode bending moments, or acceleration plots versus dynamic pressure or wind velocity is explained. Portions of the Skylab 2 tape data were analyzed statistically in the form of power spectral densities, autocorrelations, and cross correlations to introduce a concept of using system response decay as a measure of linear system damping.

Source record↗
NASA NTRS1974

Task 60 test report, evaluation of IRIG-A 21 channel constant bandwith FM multiplexer for shuttle development flight instrumentation

A frequency modulated (FM) multiplexer, consisting of 21 IRIG-A constant bandwidth (CBW) voltage-controlled oscillators (VCO's) was tested to determine its suitability for use in multiplexing 21 data signals which have frequency ranges of dc to 2 kHz. Tests were preformed with the composite signal, consisting of the mixed outputs of the 21 VCO's connected directly to a set of subcarrier discriminators, with the signal recorded on magnetic tape and played back through the discriminators and with the signal transmitted by a frequency-modulated FM S-band radio frequency RF transmitter to a FM receiver and through the subcarrier discriminators. Tape speed flutter was induced to determine the reduction in flutter noise which can be obtained by the tape speed compensation equipment. The RF transmission test included transmitting the composite signal at a nominal RF received signal of -73 dbm and at RF levels of -83 and -86 dbm.

Haddick, C. M.↗
NASA NTRS1973

Implementation and extension of the impulse transfer function method for future application to the space shuttle project. Volume 2: Program description and user's guide

The data processing procedures and the computer programs were developed to predict structural responses using the Impulse Transfer Function (ITF) method. There are three major steps in the process: (1) analog-to-digital (A-D) conversion of the test data to produce Phase I digital tapes (2) processing of the Phase I digital tapes to extract ITF's and storing them in a permanent data bank, and (3) predicting structural responses to a set of applied loads. The analog to digital conversion is performed by a standard package which will be described later in terms of the contents of the resulting Phase I digital tape. Two separate computer programs have been developed to perform the digital processing.

Patterson, G.↗
NASA NTRS1973

Vibration resistance of the wire-feed mechanism of a magnetic recording apparatus

The effects of external mechanical and climatic actions on the efficient operation of magnetic tape recording equipment are analyzed. The efficiency and reliability of the recording system are determined by the structural parameters and the characteristics of the individual elements of the transport mechanism circuit. The resistance of tape recording equipment to the effects of vibration is considered essential for reliable operations. Methods for insuring reliable tape transport and recording action are discussed.

Kitra, S. P.↗
NASA NTRS1974

Analysis of cross beam runs taken at Haswell Field site, October 1969

A series of cross beam experiments was conducted at the ESSA field site at Haswell, Colorado. Both the optical visual and infrared units were operated on a comparison basis. A data report of the initial auto- and cross-correlation evaluation of these tests is presented. The original test data from the Haswell tests were recorded on F M magnetic tape. A copy of the original tapes was made and employed for the present analysis. The tapes were played back at 60 inches per second for analysis. Some of the infrared units runs (Run Nos. 8,25,40,41,42,43,44,45) were played back at 30 inches per second in order to gain sufficient averaging time. The averaging time was nominally 3200 seconds real time at 60 inches per second and 1600 seconds real time at 30 inches per second. These averaging times correspond to 100 seconds of averaging time of the correlator.

Huff, L. L.↗
NASA NTRS1972

A communication link between the GIM data base and a general application program

Utilizing the extract verb of GIM causes the requested information to be extracted from the GIM base and written on to tape. When the GIM extract has completed, a FORTRAN program is then compiled and executed. This program reads the tape generated by GIM, formats and prints the extracted data on the line printer. When an end of file on the extracted tape is encountered the job is terminated.

Argo, W. V.↗
NASA NTRS1977

Development ephemeris number 96

Program tape contains two files: file one contains all software necessary to create binary file and perform ephemeris calculation on that file; file two of distributed tape contains encoded ephemeris data. These data are essentially a blocked listing of complete dump of original binary tape, with double precision data modified to special form.

Keesey, M. S. W.↗
NASA NTRS1975

Pyrotechnic shock measurement and data analysis requirements

An investigation is described into the laboratory measurement and analysis of pyrotechnic shock which was prompted at JPL when two separate facilities generated discrepant pyrotechnic shock data while testing Mariner Jupiter/Saturn 1977 spacecraft hardware. Both of the testing facilities were surveyed. The only difference noted was in the FM tape recorders used to record the data. One facility used a tape recorder operating at 60 in./sec with a frequency response of 20 kHz; the other used a tape recorder operating at 120 in./sec with a frequency response of 80 kHz. The accelerometers, cables, charge amplifiers, and mechanical setups were identical.

Albers, L.↗
NASA NTRS1975

Ohio's statewide land use inventory: An operational approach for applying LANDSAT data to state, regional and local planning programs

The programmatic, technical, user application, and cost factors associated with the development of an operational, statewide land use inventory from LANDSAT data are described. The LANDSAT multispectral data are subjected to geometrical and categorical processing to produce map files for each of the 200 fifteen (15) minute quads covering Ohio. Computer compatible tapes are rescanned to produce inventory tapes which identify eight (8) Level I land use categories and a variety of Level II categories. The inventory tapes are processed through a series of ten (10) software programs developed by the State of Ohio. The net result is a computerized inventory which can be displayed in map or tabular form for various geographic units, at a variety of scales and for selected categories of usage. The computerized inventory data files are applied to technical programs developed by the various state agencies to be used in state, regional, and local planning programs.

Baldridge, P. E.↗
NASA NTRS1976

Program documentation crew system vidar data reduction (CSVIDR) program

The Crew System Vidar Data Reduction (CSVIDR) program was written to process selected portions of data acquired from long term tests of space shuttle crew equipment. Data are recorded on a seven track computer compatible tape using the Vidar autodata eight processing system. The input tape is in a six bit binary coded decimal format. The 1110 hardware conversion option is used to convert all data from a BCD format to Fieldata since the majority of the data is output without further conversion. Data is retrieved from a character string, calibrated, tabulated, printed, and output on a fixed sample rate tape for use as input to a general purpose plot program.

Vanwie, H. B.↗
NASA NTRS1976

Short time transient periodicities from Cyg X-1

The temporal behavior of three new events of modulated optical emission from Cyg X1, detected in July 1975, is presented. Short time periodicities in the optical band are investigated. Single photon pulses from the photomultiplier are recorded on magnetic tape together with a very accurate 1 kHz reference frequency. During playback of the tape, the reference signal gives a 1 ms timing to a scaler interfaced with a small processor and the number of photon per millisecond is recorded on a digital tape.

Auriemma, G.↗
NASA NTRS1975

Pyrotechnic shock measurement and data analysis requirements

An investigation of laboratory measurement and analysis of pyrotechnic shock is described which was prompted when two separate facilities produced discrepant pyrotechnic-shock data while testing Mariner Jupiter/Saturn 1977 spacecraft hardware. Both testing facilities are thoroughly examined to find a possible cause for the discrepancies, and it is noted that one facility incorporated an FM tape recorder operating at 60 in./sec with a frequency response of 20 kHz while the other incorporated a tape recorder operating at 120 in./sec with a frequency response of 80 kHz. It is found that the discrepancies were a direct result of the inadequate recording frequency response of the tape recorders. Other factors involved in obtaining more accurate data are discussed.

Albers, L.↗