Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Influence of carrier trapping on radiation detection properties in $\mathrm{CVD}$ grown 4H-SiC epitaxial layers with varying thickness up to 250 µm

We report low doped n-type 4H-SiC epitaxial layers of thickness 50, 150, and 250 µm grown by hot wall chemical vapor deposition were used to fabricate Ni/4H-SiC Schottky radiation detectors. The epitaxial layers were grown on the (0001) face of highly conductive bulk 4H-SiC substrates 8° offcut towards the $\langle 11\bar{2}1\rangle$ direction. The 50, 150, and 250 µm thick epilayer detectors, under optimized settings, showed energy resolutions of 2.0%, 0.78%, and 0.63%, respectively for 5.48 MeV alpha particles. Deep level transient spectroscopy studies showed that the observed variation in the detector resolution is linked to the defect parameters in the devices. Least-squares fitting of the bias dependence of the charge collection efficiency according to a drift-diffusion model, revealed minority carrier diffusion lengths of 16, 10, and 9.2 µm, respectively, implying that the detectors are not limited by minority carrier trapping. The detector performance was observed to be primarily dependent on the concentration and capture cross-sections of the lifetime killing electron traps Z 1/2 and EH 6/7 .

36 MATERIALS SCIENCE↗

The Effect of Grain Size and Phosphorous-doping of Polycrystalline 3C-SiC on Infrared Reflectance Spectra

The effect of P-doping and grain size of polycrystalline 3C-SiC on the infrared reflectance spectra is reported. The relationship between grain size and full width at half maximum (FWHM) suggest that the behaviour of the 3C-SiC with the highest phosphorous doping level (of 1.2 x 10{sup 19} at. cm{sup -3}) is different from those with lower doping levels (< 6.6 x 10{sup 18} at. cm{sup -3}). It is also further demonstrated that the plasma resonance frequency (w{sub p}) is not influenced by the grain size.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of exposure environment on surface decomposition of SiC-silver ion implantation diffusion couples

SiC is a promising material for nuclear applications and is a critical component in the construction of tristructural isotropic (TRISO) fuel. A primary issue with TRISO fuel operation is the observed release of 110m Ag from intact fuel particles. The release of Ag has prompted research efforts to directly measure the transport mechanism of Ag in bulk SiC. Recent research efforts have focused primarily on Ag ion implantation designs. The effect of the thermal exposure system on the ion implantation surface has been investigated. Results indicate the utilization of a mated sample geometry and the establishment of a static thermal exposure environment is critical to maintaining an intact surface for diffusion analysis. In conclusion, the nature of the implantation surface and its potential role in Ag diffusion analysis are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of SiC grain boundary character on fission product transport in irradiated TRISO fuel

The relationship between grain boundary character and fission product migration is identified as an important knowledge gap in order to advance the understanding of fission product release from TRISO fuel particles. Precession electron diffraction (PED), a TEM-based technique, was used in this study to quickly and efficiently provide the crystallographic information needed to identify grain boundary misorientation, grain boundary type (low or high angle) and whether the boundary is coincident site lattice (CSL) – related, in irradiated SiC. Analysis of PED data showed the grain structure of the SiC layer in an irradiated TRISO fuel particle from the AGR-1 experiment to be composed mainly of twin boundaries with a small fraction of low angle grain boundaries (<10%). In general, fission products favor precipitation on random, high angle grain boundaries but can precipitate out on low angle and CSL-related grain boundaries to a limited degree. Pd is capable of precipitating out on all types of grain boundaries but most prominently on random, high angle grain boundaries. Pd-U and Pd-Ag precipitates were found on CSL-related as well as random high angle grain boundaries but not on low angle grain boundaries. In contrast, precipitates containing only Ag were found only on random, high angle grain boundaries but not on either low angle or CSL-related grain boundaries.

36 MATERIALS SCIENCE↗

Characterization of PVD Cr, CrN, and TiN coatings on SiC

SiC ceramic matrix composites are a potential replacement for current light water nuclear reactor fuel cladding material. However, loss of fission gas via micro-cracks and corrosion remain an issue. Cathodic arc Cr, CrN, and TiN coatings were deposited on SiC tubes and plates to provide hermeticity and corrosion resistance. These coatings were characterized to determine as-deposited quality. Cross-sectional microscopy, X-ray diffraction, glow discharge optical emission spectroscopy, and scratch tests were performed to evaluate the purity, structure, and mechanical performance of the coatings. Nitride coatings had stable interfaces, but larger defects in the coatings as compared to the Cr coatings which showed cracking at the interface, but less deposition-induced defects. Despite the local state of the interface, the mechanical properties of the metallic coatings versus ceramic coatings enabled the Cr coatings to resist loads three times that of the nitride coatings during scratch tests. Finally, glow-discharge optical emission spectroscopy showed that improvement in elemental purity is needed for future coatings.

36 MATERIALS SCIENCE↗

The effects of neutron and ionizing irradiation on the aqueous corrosion of SiC

Chemical vapor deposited (CVD) SiC and nuclear-grade SiC/SiC composite materials were exposed to light water reactor (LWR) conditions at the MIT Nuclear Reactor (MITR) here. Three sets of samples were exposed within flowing PWR-chemistry-coolant under either 1) neutron and ionizing irradiation with resulting radiolysis products, 2) radiolysis products without neutron flux, 3) loop coolant. Post-irradiation examination (PIE) exhibited an increase in corrosion from radiolysis products (particularly H 2 O 2 ), and potentially a further increase from radiation damage. For CVD SiC, regardless of exposure location, the in-situ observed corrosion rate was less than 1 µm per year, potentially within acceptable limits for LWR application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrothermal corrosion behavior of CVD SiC in high temperature water

Here, the hydrothermal corrosion of polished and as-cut high purity chemical vapor deposited (CVD) SiC was studied in a constantly refreshing water loop. Light water reactor (LWR) conditions were simulated at 288, 320, and 350 °C with dissolved gas concentrations between 0.15 and 3 ppm H 2 or between 1 and 4 ppm O 2 . In hydrogenated water, the rate of material loss was low, calculated to be ~1.3 μm of recession after 5 years of service in 320 °C water. Moreover, there was no observed localized attack at any temperature. In oxygenated conditions, the corrosion rate was higher, with a calculated material loss >10 μm after 5 years of service in 1 ppm O 2 , 320 °C water. Mass loss significantly increased when grain fallout became significant (as early as 200h with 4 ppm O 2 at 350 °C or after 1000–2000h with 2 ppm O 2 at 288 °C). Grain fallout more than doubled the corrosion rate and a steady state corrosion rate in the grain fallout regime was not observed but expected to eventually occur once large grains begin to be removed. Polished specimens had lower mass loss than unpolished coupons. A kinetic analysis of the data in this work suggests that the corrosion rates are controlled by a single activation step in both oxygenated and deoxygenated conditions, with the reaction order with respect to oxygen being 1. A resulting reaction rate equation to predict corrosion of SiC (in mg/cm 2 s) in high purity water from 288 to 350 °C and up to 4 ppm O 2 was constructed: Rate = $\frac{0.1458}{1+SA}$ T (1.09(1–10 -3 T)[O 2 ]e– $\frac{1.275x10^4}{T}$ + 7.91x10 -6 e– $\frac{7.39x10^3}{T}$).

36 MATERIALS SCIENCE↗

Irradiation-induced chemical disordering in ceramics: The case of SiC

Chemical disordering is one feature of damage that occurs in irradiation environments and is common in ceramic compounds. This paper reviews irradiation-induced chemical disordering in SiC-based materials at elevated temperatures. Here the results were obtained using advanced analytical tools to characterize atomistic defects and to evaluate the chemistry of defect clusters and homonuclear bond structures. Finally, this paper demonstrates that chemical disordering is crucial to understanding microstructural stability and establishing a mechanistic modeling of microstructural evolution of irradiated SiC.

36 MATERIALS SCIENCE↗

Characterization of Defects in N-type 4H-SiC After High-Energy N Ion Implantation by RBS-Channeling and Raman Spectroscopy

Implantation with 1 MeV N ions was performed at room temperature in n-type 4H-SiC(0001) to four implantation fluences (or doses in dpa (displacements per atom) at the damage peak) of 1.5×1013(0.0034), 7.8×1013(0.018), 1.5×1014(0.034), and 7.8×1014(0.18) ions/cm2, respectively. The evolution of disorder was studied using Rutherford backscattering spectrometry in channeling mode (RBS-C) and Raman spectroscopy. The disorder in the Si sub-lattice was found to be less than 10% for the dpa of 0.0034 and 0.0178 and increased to 40% and 60% for the dpa of 0.034 and 0.178 respectively. Raman Spectroscopy was performed using a green laser of wavelength 532 nm as excitation source. The normalized Raman Intensity, In shows disorder of 41%, 69%, 77% and 100% for the dpa of 0.0034, 0.017, 0.034 and 0.178 respectively. In this paper, the characterizations of the defects produced due to the Nitrogen implantation in 4H-SiC are presented and the results are discussed.

Environmental Molecular Sciences Laboratory↗

IMPACT OF DIELECTRIC PARAMETERS ON THE REFLECTIVITY OF 3C-SiC WAFERS WITH A ROUGH SURFACE MORPHOLOGY IN THE RESTSTRAHLEN REGION

A layer-on-substrate model is used to obtain the infrared reflectance for 3C-SiC with a rough surface morphology. The effect of varying dielectric parameters of the “damaged layer” on the observed reflectivity of the 3C-SiC in the reststrahlen region is assessed. Different simulated reflectance spectra are obtained to those if the dielectric parameters of the “substrate” were varied. Most notable changes in the shape of the simulated reststrahlen peak are observed for changes in the high frequency dielectric constant, the phonon damping constant, the phonon frequencies and “thickness” of damaged surface layer.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nanomechanical Behavior of Single Crystalline SiC Nanotubes Revealed by Molecular Dynamics Simulations

Molecular dynamics simulations with Tersoff potentials were used to study the response of single crystalline SiC nanotubes under tensile, compressive, torsional, combined tension-torsional and combined compression-torsional strains. The simulation results reveal that the nanotubes deform through bond-stretching and breaking and exhibit brittle properties under uniaxial tensile strain, except for the thinnest nanotube at high temperatures, which fails in a ductile manner. Under uniaxial compressive strain, the SiC nanotubes buckle with two modes, i.e. shell buckling and column buckling, depending on the length of the nanotubes. Under torsional strain, the nanotubes buckle either collapse in the middle region into a dumbbell-like structure for thinner wall thicknesses or fail by bond breakage for the largest wall thickness. Both the tensile failure stress and buckling stress decrease under combined tension-torsional and combined compression-torsional strain, and they decrease with increasing torsional rate under combined loading.

36 MATERIALS SCIENCE↗

Mechanical behavior of twinned SiC nanowires under combined tension-torsion and compression-torsion strain

The mechanical behavior of twinned silicon carbide (SiC) nanowires under combined tension-torsion and compression-torsion is investigated using molecular dynamics simulations with an empirical potential. The simulation results show that both the tensile failure stress and buckling stress decrease under combined tension-torsional and combined compression-torsional strain, and they decrease with increasing torsional rate under combined loading. The torsion rate has no effect on the elastic properties of the twinned SiC nanowires. The collapse of the twinned nanowires takes place in a twin stacking fault of the nanowires.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optoelectronic and structural characterization of trapezoidal defects in 4H-SiC epilayers and the effect on MOSFET reliability

To this day, trapezoidal defects are found in clusters and high counts in wafers representing the industry standard in terms of material quality being produced. This study sheds light on the nature, origin, behavior, and impact of this defect on device yield and reliability. Trapezoidal defects in 4H-SiC epitaxial layers were investigated by photoluminescence (PL) imaging, scanning electron microscopy (SEM), cathodoluminescence spectrum imaging (CLSI), SEM electron beam induced current (EBIC) imaging, and by transmission electron microscopy (TEM) observation. The bar-shaped stacking faults were identified by the PL and CL measurements with a peak emission wavelength of 420 and 450 nm. An optoelectronic behavioral study based on the recombination enhanced dislocation glide mechanism revealed how expanding dislocations and stacking faults interact with each other. Combining the luminescence and microscopy results, the nature of the stacking faults was identified as being a combination of Shockley-type and Frank-type stacking faults. The TEM analysis showed that these defects originate from the substrate and the stacking sequences of some of the faults were determined as (…2, 4, 2…) and (…2, 3, 2…) in the Zhdanov's notation by high-resolution TEM. The origin of this defect is speculated based on our results and previous reports. The EBIC imaging showed that the high density of SFs in these towers is a strong site of carrier recombination, which presumably has an impact on the transfer characteristics of SiC devices. Furthermore, these defects have shown to impact metal oxide semiconductor field effect transistors electrical performance via an increase in the on-state resistance depending on the coverage percentage of the tower of defects in the active area of the device.

4H-SiC↗

Ab initio molecular dynamics simulation of pressure-induced zinc blende to rocksalt phase transition in SiC

The high-pressure induced phase transformation from the zinc blende to rocksalt structure in SiC has been studied by ab initio molecular dynamics. The simulations show that SiC passes through tetragonal and then monoclinic intermediate states before finally forming the rock salt structure at 160 GPa. The mechanism for this phase transformation agrees well with recent ab initio MD simulations, in which the applied pressure was as high as ~600 GPa, but in the present study the transformation occurs at much lower pressure. It is found that the phase transition has to overcome an energy barrier of 0.44 eV/pair.

36 MATERIALS SCIENCE↗

Dispersed SiC nanoparticles in Ni observed by ultra-small-angle X-ray scattering

In this paper, a metal-ceramic composite, nickel reinforced with SiC nanoparticles, was synthesized and characterized for its potential application in next-generation molten salt nuclear reactors. Synchrotron ultra-small-angle X-ray scattering (USAXS) measurements were conducted on the composite. The size distribution and number density of the SiC nanoparticles in the material were obtained through data modelling. Scanning and transmission electron microscopy characterization were performed to substantiate the results of the USAXS measurements. Tensile tests were performed on the samples to measure the change in their yield strength after doping with the nanoparticles. Finally, the average interparticle distance was calculated from the USAXS results and is related to the increased yield strength of the composite.

36 MATERIALS SCIENCE↗

A Modular SiC High-Frequency Solid-State Transformer for Medium-Voltage Applications: Design, Implementation, and Testing

The advancements in wide-bandgap devices are enabling applications of power electronic converters coupled directly with medium-voltage (MV) grids that incorporate galvanic isolation within the converter using high-frequency solid-state transformers (SSTs). This paper presents analysis, design, and the characterization results of a 50-kVA modular soft-switched ac-ac SST using silicon carbide (SiC) MOSFET for MV (>6 kV ac) applications. Here, the SST is comprised of two hard-switched ac-line interface bridges and a resonant dc-dc stage switched at approximately 180 kHz. To minimize the cost of switching elements per ampere and maximize the design flexibility, the design uses multiple discrete SiC devices of, readily available, 1700-V ratings. This paper covers the analysis of soft-switching operation, control architecture, converter design, and system-level integration.

17 WIND ENERGY↗

Self-Powering High Frequency Modulated SiC Power MOSFET Isolated Gate Driver

A novel implementation of an isolated gate driver for power switches is proposed in this study. The driver is bespoke designed for SiC power mosfet s. The proposal achieves the main driver characteristics—isolation capability, gate switching command, and power transfer to the secondary side by using a unique magnetic transformer. The resulting simple circuitry enables the integration of the driver into the power cell, achieving theoretical higher power density values of the final system. The principle of operation of the driver is described in detail. The original pulsewidth modulation signal is modulated with a pure ac square waveform under a two-level modulation scheme, that guarantees no saturation of the magnetic core. Here, the signal is then magnetically coupled to the secondary side, where it is rectified and reconstructed to effectively drive the target device. In addition, the steps needed to provide a suitable design taking into account the parameters of the target power switch are also detailed. The resulting driver is characterized and a prototype of the driver is built and tested. The main results of the driver performance on a SiC mosfet -based prototype are presented. Based on the analysis of these results, this study experimentally demonstrates the feasibility of the proposal.

25 ENERGY STORAGE↗

Development of a 250 Degree C 15kV Supercascode Switch Using SiC JFET Technology

Tetra Corporation is developing a pulsed power drilling system for the geothermal industry. The system requires a high temperature switching technology to replace the existing technology based on Si thyristors with a temperature limit of 150 degrees C. This work focuses on the development of such switch based on a Supercascode configuration using SiC JFET technology. The development presented contains thermal models, packaging design and processes, circuit simulations and prototypes of both the Supercascode switch and the high temperature packaged SiC JFETs.

cascaded switch↗