Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SAPPHIRE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Composite arrays of superconducting microstrip line resonators

A novel design of an array of half-wave superconductive microstrip resonators is described. The resonator is intended to be useful for electron spin resonance studies of thin film samples at cryogenic temperatures. It achieves a high quality factor, has a small mode-volume, and creates a uniform magnetic field in a plane above the resonator. The device is made of thin film Niobium on sapphire wafer and is tested with a static magnetic field. Variation of Q-factor versus the magnetic field's strength at different temperatures is reported and is in a good agreement with simulation when the loss due to the vortices is included. Also, the power-dependence response of the resonator is shown in experiments and is verified by capturing the nonlinearity associated with the surface impedance of the superconducting film into the circuit model of the device.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature dependent dielectric function and the E{sub 0} critical points of hexagonal GaN from 30 to 690 K

The complex dielectric function ε and the E{sub 0} excitonic and band-edge critical-point structures of hexagonal GaN are reported for temperatures from 30 to 690 K and energies from 0.74 to 6.42 eV, obtained by rotating-compensator spectroscopic ellipsometry on a 1.9 μm thick GaN film deposited on a c-plane (0001) sapphire substrate by molecular beam epitaxy. Direct inversion and B-splines in a multilayer-structure calculation were used to extract the optical properties of the film from the measured pseudodielectric function 〈ε〉. At low temperature sharp E{sub 0} excitonic and critical-point interband transitions are separately observed. Their temperature dependences were determined by fitting the data to the empirical Varshni relation and the phenomenological expression that contains the Bose-Einstein statistical factor.

36 MATERIALS SCIENCE↗

Tunable vacuum ultraviolet laser based spectrometer for angle resolved photoemission spectroscopy

We have developed an angle-resolved photoemission spectrometer with tunable vacuum ultraviolet laser as a photon source. The photon source is based on the fourth harmonic generation of a near IR beam from a Ti:sapphire laser pumped by a CW green laser and tunable between 5.3 eV and 7 eV. The most important part of the set-up is a compact, vacuum enclosed fourth harmonic generator based on potassium beryllium fluoroborate crystals, grown hydrothermally in the US. This source can deliver a photon flux of over 10{sup 14} photon/s. We demonstrate that this energy range is sufficient to measure the k{sub z} dispersion in an iron arsenic high temperature superconductor, which was previously only possible at synchrotron facilities.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The role of band alignment in p-type conductivity of Na-doped ZnMgO: Polar versus non-polar

We investigate the electrical properties of polar and non-polar ZnMgO:Na films that have been fabricated on c-plane and r-plane sapphire substrates using intervened ZnO layers (10–30 nm thick) by pulsed laser deposition. Hall-effect measurements indicate that the a-plane ZnMgO:Na film exhibits p-type conductivity with a carrier concentration of about 3.5 × 10{sup 16} cm{sup −3}, while the polar film shows a compensatory conductivity. Meanwhile, the dependence of the band alignment on the orientation of the ZnMgO/ZnO heterojunctions has been investigated using photoelectron spectroscopy. The heterojunctions form in the type-I straddling alignment with valence band offsets of 0.07 (0.02) eV for the (non-)polar heterojunction. The difference in valence band offsets is primarily attributed to the spontaneous polarization effect. We propose that the smaller valence band offsets and larger conduction band offsets would reduce the Na{sub Zn} acceptor level and enhance the relative intrinsic donor levels. Such effects consequently lead to p-type conductivity in non-polar ZnMgO:Na films. The band alignment of non-polar ZnMgO/ZnO can be used to facilitate p-type doping with a shallower acceptor state in the ZnO-like alloy.

36 MATERIALS SCIENCE↗

The development and deployment of a ground-based, laser-induced fluorescence instrument for the in situ detection of iodine monoxide radicals

High abundances of iodine monoxide (IO) are known to exist and to participate in local photochemistry of the marine boundary layer. Of particular interest are the roles IO plays in the formation of new particles in coastal marine environments and in depletion episodes of ozone and mercury in the Arctic polar spring. This paper describes a ground-based instrument that measures IO at mixing ratios less than one part in 10{sup 12}. The IO radical is measured by detecting laser-induced fluorescence at wavelengths longer that 500 nm. Tunable visible light is used to pump the A{sup 2}Π{sub 3/2} (v{sup ′} = 2) ← X{sup 2}Π{sub 3/2} (v{sup ″} = 0) transition of IO near 445 nm. The laser light is produced by a solid-state, Nd:YAG-pumped Ti:Sapphire laser at 5 kHz repetition rate. The laser-induced fluorescence instrument performs reliably with very high signal-to-noise ratios (>10) achieved in short integration times (<1 min). The observations from a validation deployment to the Shoals Marine Lab on Appledore Island, ME are presented and are broadly consistent with in situ observations from European Coastal Sites. Mixing ratios ranged from the instrumental detection limit (<1 pptv) to 10 pptv. These data represent the first in situ point measurements of IO in North America.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Dual-polarity GaN micropillars grown by metalorganic vapour phase epitaxy: Cross-correlation between structural and optical properties

Self-assembled catalyst-free GaN micropillars grown on (0001) sapphire substrates by metal organic vapor phase epitaxy are investigated. Transmission electron microscopy, as well as KOH etching, shows the systematic presence of two domains of opposite polarity within each single micropillar. The analysis of the initial growth stages indicates that such double polarity originates at the micropillar/substrate interface, i.e., during the micropillar nucleation, and it propagates along the micropillar. Furthermore, dislocations are also generated at the wire/substrate interface, but bend after several hundreds of nanometers. This leads to micropillars several tens of micrometers in length that are dislocation-free. Spatially resolved cathodoluminescence and microphotoluminescence show large differences in the optical properties of each polarity domain, suggesting unequal impurity/dopant/vacancy incorporation depending on the polarity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hydride vapor phase epitaxy and characterization of high-quality ScN epilayers

The heteroepitaxial growth of ScN films was investigated on various substrates by hydride vapor phase epitaxy (HVPE). Single crystalline mirror-like ScN(100) and ScN(110) layers were successfully deposited on r- and m-plane sapphire substrates, respectively. Homogeneous stoichiometric films (N/Sc ratio 1.01 ± 0.10) up to 40 μm in thickness were deposited. Their mosaicity drastically improved with increasing the film thickness. The band gap was determined by optical methods to be 2.06 eV. Impurity concentrations including H, C, O, Si, and Cl were investigated through energy dispersive X-ray spectrometry and secondary ion mass spectrometry. As a result, it was found that the presence of impurities was efficiently suppressed in comparison with that of HVPE-grown ScN films reported in the past, which was possible thanks to the home-designed corrosion-free HVPE reactor. Room-temperature Hall measurements indicated that the residual free electron concentrations ranged between 10{sup 18}–10{sup 20} cm{sup −3}, which was markedly lower than the reported values. The carrier mobility increased monotonically with the decreasing in carrier concentration, achieving the largest value ever reported, 284 cm{sup 2} V{sup −1} s{sup −1} at n = 3.7 × 10{sup 18} cm{sup −3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pump-probe surface photovoltage spectroscopy measurements on semiconductor epitaxial layers

Pump-probe Surface Photovoltage Spectroscopy (SPS) measurements are performed on semiconductor epitaxial layers. Here, an additional sub-bandgap cw pump laser beam is used in a conventional chopped light geometry SPS setup under the pump-probe configuration. The main role of pump laser beam is to saturate the sub-bandgap localized states whose contribution otherwise swamp the information related to the bandgap of material. It also affects the magnitude of Dember voltage in case of semi-insulating (SI) semiconductor substrates. Pump-probe SPS technique enables an accurate determination of the bandgap of semiconductor epitaxial layers even under the strong influence of localized sub-bandgap states. The pump beam is found to be very effective in suppressing the effect of surface/interface and bulk trap states. The overall magnitude of SPV signal is decided by the dependence of charge separation mechanisms on the intensity of the pump beam. On the contrary, an above bandgap cw pump laser can be used to distinguish the signatures of sub-bandgap states by suppressing the band edge related feature. Usefulness of the pump-probe SPS technique is established by unambiguously determining the bandgap of p-GaAs epitaxial layers grown on SI-GaAs substrates, SI-InP wafers, and p-GaN epilayers grown on Sapphire substrates.

36 MATERIALS SCIENCE↗

Generation and transportation mechanisms for two-dimensional hole gases in GaN/AlGaN/GaN double heterostructures

The electrical properties of two-dimensional hole gases (2DHGs) in GaN/AlGaN/GaN double heterostructures were investigated. The layers were grown on sapphire substrates and a high-quality bulk GaN substrate. The coexistence of 2DHG and 2D electron gases on both sides of the AlGaN layer was confirmed by Hall effect measurements at 80–460 K. It was also verified that the 2DHGs were generated by negative polarization at the undoped GaN/AlGaN interface, which did not have a doped Mg acceptor. It was also demonstrated that the 2DHG density could be controlled by varying the AlGaN layer thickness and was inversely related to the 2DHG mobility. The measured relation indicated that the 2DHG mobility is mainly limited by phonon scatterings at around room temperature. As a result, the maximum 2DHG mobility of 16 cm{sup 2}/Vs at 300 K was achieved with a density of 1 × 10{sup 13} cm{sup −2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Al-mole fraction in Al{sub x}Ga{sub 1−x}N grown by MOCVD

AlGaN/AlN layers were grown by metalorganic chemical vapor deposition (MOCVD) on sapphire substrates. The Al{sub x}Ga{sub 1−x}N layer composition was varied from 15% to 25%. The crystalline quality, thickness and aluminum (Al) composition of AlGaN were determined using high resolution X-ray diffraction (HRXRD). The growth rate decreases on increasing Al composition. Reciprocal space mapping (RSM) was used to estimate the strain and relaxation between AlGaN and AlN. The optical properties of AlGaN layers were investigated by room temperature Photoluminescence (PL). The AlGaN peak shifts towards lower wavelength with Al composition. The surface morphology of AlGaN was studied by atomic force microscopy (AFM). Root mean square (RMS) roughness values were found to be increased in AlGaN layers with composition.

36 MATERIALS SCIENCE↗

Thickness dependent metal-insulator transition and dimensional crossover for weak localization in Si{sub 0.02}Zn{sub 0.98}O thin films grown by pulsed laser deposition

Metal to insulator transition was observed in Si{sub 0.02}Zn{sub 0.98}O (SZO) films, grown by pulsed laser deposition on sapphire substrates, as the thicknesses of the films were reduced from ∼40 to 15 nm. The SZO film with thickness of ∼40 nm showed typical metallic behavior in temperature dependent resistivity measurements. On the contrary, the SZO film with thickness of ∼15 nm was found to exhibit strong localization where the transport at low temperature was dominated by variable range hopping conduction. In the intermediate thickness regime, quantum corrections were important and a dimensional crossover from 3D to 2D weak localization occurred in the SZO film with thickness of 20 nm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Note: A rigid piezo motor with large output force and an effective method to reduce sliding friction force

We present a completely practical TunaDrive piezo motor. It consists of a central piezo stack sandwiched by two arm piezo stacks and two leg piezo stacks, respectively, which is then sandwiched and spring-clamped by a pair of parallel polished sapphire rods. It works by alternatively fast expanding and contracting the arm/leg stacks while slowly expanding/contracting the central stack simultaneously. The key point is that sufficiently fast expanding and contracting a limb stack can make its two sliding friction forces well cancel, resulting in the total sliding friction force is <10% of the total static friction force, which can help increase output force greatly. The piezo motor's high compactness, precision, and output force make it perfect in building a high-quality harsh-condition (vibration resistant) atomic resolution scanning probe microscope.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Mid-infrared intersubband absorptions in ZnO/ZnMgO multiple quantum wells

The authors report the observation of intersubband absorptions in ZnO/ZnMgO multiple quantum wells (QWs). The multiple QW structures were grown on c-plane sapphire substrates by plasma-assisted molecular beam epitaxy. The high structural and optical properties of the samples were demonstrated by high-resolution x-ray diffraction and photoluminescence measurements. At room temperature, intersubband absorptions at ∼3 μm were observed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct writing of continuous and discontinuous sub-wavelength periodic surface structures on single-crystalline silicon using femtosecond laser

Laser-induced ripples or uniform arrays of continuous near sub-wavelength or discontinuous deep sub-wavelength structures are formed on single-crystalline silicon (Si) by femtosecond (fs) laser direct writing technique. Laser irradiation was performed on Si wafers at normal incidence in air and by immersing them in dimethyl sulfoxide using linearly polarized Ti:sapphire fs laser pulses of ∼110 fs pulse duration and ∼800 nm wavelength. Morphology studies of laser written surfaces reveal that sub-wavelength features are oriented perpendicular to laser polarization, while their morphology and spatial periodicity depend on the surrounding dielectric medium. The formation mechanism of the sub-wavelength features is explained by interference of incident laser with surface plasmon polaritons. This work proves the feasibility of fs laser direct writing technique for the fabrication of sub-wavelength features, which could help in fabrication of advanced electro-optic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Plasmonic formation mechanism of periodic 100-nm-structures upon femtosecond laser irradiation of silicon in water

The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of silicon by multiple (N = 100) linearly polarized Ti:sapphire femtosecond laser pulses (duration τ = 30 fs, center wavelength λ{sub 0} ∼ 790 nm) is studied experimentally in air and water environment. The LIPSS surface morphologies are characterized by scanning electron microscopy and their spatial periods are quantified by two-dimensional Fourier analyses. It is demonstrated that the irradiation environment significantly influences the periodicity of the LIPSS. In air, so-called low-spatial frequency LIPSS (LSFL) were found with periods somewhat smaller than the laser wavelength (Λ{sub LSFL} ∼ 0.7 × λ{sub 0}) and an orientation perpendicular to the laser polarization. In contrast, for laser processing in water a reduced ablation threshold and LIPSS with approximately five times smaller periods Λ{sub LIPSS} ∼ 0.15 × λ{sub 0} were observed in the same direction as in air. The results are discussed within the frame of recent LIPSS theories and complemented by a thin film based surface plasmon polariton model, which successfully describes the tremendously reduced LIPSS periods in water.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-performance solar-blind ultraviolet photodetector based on mixed-phase ZnMgO thin film

High Mg content mixed-phase Zn{sub 0.38}Mg{sub 0.62}O was deposited on a-face sapphire by plasma-assisted molecular beam epitaxy, based on which a metal-semiconductor-metal solar-blind ultraviolet (UV) photodetector was fabricated. The dark current is only 0.25 pA at 5 V, which is much lower than that of the reported mixed-phase ZnMgO photodetectors. More interestingly, different from the other mixed-phase ZnMgO photodetectors containing two photoresponse bands, this device shows only one response peak and its −3 dB cut-off wavelength is around 275 nm. At 10 V, the peak responsivity is as high as 1.664 A/W at 260 nm, corresponding to an internal gain of ∼8. The internal gain is mainly ascribed to the interface states at the grain boundaries acting as trapping centers of photogenerated holes. In view of the advantages of mixed-phase ZnMgO photodetectors over single-phase ZnMgO photodetectors, including easy fabrication, high responsivity, and low dark current, our findings are anticipated to pave a new way for the development of ZnMgO solar-blind UV photodetectors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stark effect in ensembles of polar (0001) Al{sub 0.5}Ga{sub 0.5}N/GaN quantum dots and comparison with semipolar (11−22) ones

This work presents a continuous-wave photoluminescence study of Al{sub 0.5}Ga{sub 0.5}N/GaN quantum dots grown by ammonia-assisted molecular beam epitaxy on sapphire, either on the wurtzite polar (0001) or the semipolar (11−22) plane. Due to interface polarization discontinuities, the polar dots are strongly red-shifted by the Stark effect and emit in the visible range. Carrier injection screening of the polarization charges has been studied. A model relying on average dot heights and dot height variances, as measured by transmission electron microscopy, is proposed. It can account for the injection dependent luminescence energies and efficiencies. The electric field discontinuity deduced from the fittings is in good agreement with theoretical expectations for our barrier composition. On the contrary, semipolar quantum dot ensembles always emit above the gap of GaN strained to Al{sub 0.5}Ga{sub 0.5}N. Their luminescence linewidth is significantly lower than that of polar ones, and their energy does not shift with injection. Our study then confirms the expected strong decrease of the Stark effect for (11−22) grown (Al,Ga)N/GaN heterostructures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal evolution of defects in undoped zinc oxide grown by pulsed laser deposition

Undoped ZnO films are grown by pulsed laser deposition on c-plane sapphire with different oxygen pressures. Thermal evolutions of defects in the ZnO films are studied by secondary ion mass spectroscopy (SIMS), Raman spectroscopy, and positron annihilation spectroscopy (PAS), and with the electrical properties characterized by the room temperature Hall measurement. Oxygen deficient defect related Raman lines 560 cm{sup −1} and 584 cm{sup −1} are identified and their origins are discussed. Thermal annealing induces extensive Zn out-diffusion at the ZnO/sapphire interface and leaves out Zn-vacancy in the ZnO film. Two types of Zn-vacancy related defects with different microstructures are identified in the films. One of them dominates in the samples grown without oxygen. Annealing the sample grown without oxygen or growing the samples in oxygen would favor the Zn-vacancy with another microstructure, and this Zn-vacancy defect persists after 1100 °C annealing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗