Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RADIATION INTENSITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Effect of X-Rays on the Mechanical Properties of Aluminized FEP Teflon(trademark)

Pieces of the multilayer insulation (MLI) that is integral to the thermal control of the Hubble Space Telescope (HST) have been returned by two servicing missions after 3.6 and 6.8 years in orbit. They reveal that the outer layer, which is made from 5 mil (0.13 mm) thick aluminized fluorinated ethylenepropylene (FEP) Teflon. has become severely embrittled. Although possible agents of this embrittlement include electromagnetic radiation across the entire solar spectrum, trapped particle radiation, atomic oxygen, and thermal cycling, intensive investigations have not yielded unambiguous causes. Previous studies utilizing monoenergetic photons in the 69-1900 eV range did not cause significant embrittlement, even at much higher doses than were experienced by the HST MLI. Neither did x-rays in the 3 to 10 keV range generated in a modified electron bean evaporator. An antidotal aluminized FEP sample that was exposed to an intensive dose from unfiltered Mo x-ray radiation from a rotating anode generator, however, did show the requisite embrittlement. Thus, a study was undertaken to determine the effects of x-ray exposure on the embrittlement of aluminized FEP in hopes that it might elucidate the HST MLI degradation mechanism. Tensile specimens of aluminized 5 mil thick FEP were exposed to a constant fluence of unfiltered x-ray radiation from a Mo target whose maximum energy ranged from 20-60 kV. Other samples were annealed, thermally cycled (100x) between 77-333 K, or cycled and irradiated. Tensile tests and density measurements were then performed on the samples. Only the samples which had been irradiated had the drastically reduced elongation-to-break, characteristic of the HST samples. Thermal cycling may accelerate the embrittlement, but the effect was near the scatter in the measurements. Annealing and thermal cycling had no apparent effect. Only the samples which had been irradiated and annealed showed significant density increases, likely implicating polymer chain scission and annealing.

Gaier, James R.↗
NASA NTRS1976

Ionising flux of cosmic background radiation

The indirect method of estimating the diffuse metagalactic flux of ionizing radiation proposed by Sunyaev (1969) is reconsidered in the light of further studies of the interaction of this radiation with galactic gas. An upper limit is derived for the intensity of the metagalactic background radiation to which the neutral interstellar medium is exposed. This limit on the ionizing radiation flux severely restricts the emission from a galactic corona containing gas in the temperature range 100,000 to 1,000,000 K. An upper limit of 10 to the 29.2 erg/sec/Hz is obtained for the mean luminosity radiated by a quasar in the energy band 40-170 eV. The 21-cm observations examined indicate that further than about 30 kpc from the center of the galaxy self-shielding by H II is possible only when the critical metagalactic ionizing flux is not exceeded.

Silk, J.↗
NASA NTRS1990

Massive soliton stars

The structure of nontopological solutions of Einstein field equations as proposed by Friedberg, Lee, and Pang (1987) is examined. This analysis incorporates finite temperature effects and pair creation. Quarks are assumed to be the only species that exist in interior of soliton stars. The possibility of primordial creation of soliton stars in the incomplete decay of the degenerate vacuum in early universe is explored. Because of dominance of pair creation inside soliton stars, the luminosity of soliton stars is not determined by its radiative transfer characteristics, and the surface temperature of soliton stars can be the same as its interior temperature. It is possible that soliton stars are intense X-ray radiators at large distances. Soliton stars are nearly 100 percent efficient energy converters, converting the rest energy of baryons entering the interior into radiation. It is possible that a sizable number of baryons may also be trapped inside soliton stars during early epochs of the universe. In addition, if soliton stars exist they could assume the role played by massive black holes in galactic centers.

Chiu, Hong-Yee↗
NASA NTRS1986

Resonant electron diffusion as a saturation process of the synchrotron maser instability

The theory of resonant electron diffusion as an effective saturation process of the auroral kilometric radiation has been formulated. The auroral kilometric radiation is assumed to be amplified by the synchrotron maser instability that is driven by an electron distribution of the loss-cone type. The calculated intensity of the saturated radiation is found to have a significantly lower value in comparison with that caused by the quasi-linear diffusion process as an alternative saturation process. This indicates that resonant electron diffusion dominates over quasi-linear diffusion in saturating the synchrotron maser instability.

Lee, M. C.↗
NASA NTRS2000

Comparison of Columnar Water Vapor Measurements During The Fall 1997 ARM Intensive Observation Period: Optical Methods

In the fall of 1997 the Atmospheric Radiation Measurement (ARM program conducted an intensive Observation Period (IOP) to study water vapor at its Southern Great Plains (SGP) site. Among the large number of instruments, four sun-tracking radiometers were present to measure the columnar water vapor (CWV). All four solar radiometers retrieve CWV by measuring solar transmittance in the 0.94-micrometer water vapor absorption band. As one of the steps in the CWV retrievals the aerosol component is subtracted from the total transmittance, in the 0.94-micrometer band. The aerosol optical depth comparisons among the same four radiometers are presented elsewhere. We have used three different methods to retrieve CWV. Without attempting to standardize on the same radiative transfer model and its underlying water vapor spectroscopy we found the CWV to agree within 0.13 cm (rms) for CWV values ranging from 1 to 5 cm. Preliminary results obtained when using the same updated radiative transfer model with updated spectroscopy for all instruments will also be shown. Comparisons to the microwave radiometer results will be included in the comparisons.

Schmid, Beat↗
NASA NTRS1991

Compact X-Ray And Extreme-Ultraviolet Monochromator

Monochromator for x-ray and extreme-ultraviolet radiation provides higher spectral resolution than achieved with thin-metal-foil broad-band-pass filters. Uses Bragg reflection to band-pass-filter radiation from high-intensity, broad-spectrum source. Operates over much broader x-ray and extreme-ultraviolet spectrum than devices based upon natural crystals. Intended to filter continuum radiation from sources like synchrotrons, laser plasma sources, free-electron lasers, and wigglers to produce monochromatic beams for testing and analysis of x-ray and extreme-ultraviolet telescopes and microscopes, for calibration of photographic films and detectors, for biological and biomedical research, for x-ray lithography, for processing of materials, and for research in properties of materials.

Hoover, Richard B.↗
NASA NTRS1975

Monte Carlo treatment of Lyman-alpha. II - Radiation in a spherical atmosphere

Intensity and state of polarization of solar L-alpha photons as they diffuse through an inhomogeneous, spherically symmetric, isothermal geocorona are theoretically determined. The fine structure of L-alpha and Doppler redistribution of frequencies are taken into account. The calculation use the Monte Carlo technique involving Stokes vectors. Comparison of the results with OGO-4 and OSO-4 observed intensities at an altitude of 650 km shows good agreement. Calculations of the polarization versus solar zenith angle show a residual polarization at large zenith angles which is mainly due to multiply scattered photons.

Modali, S. B.↗
NASA NTRS1979

Auroral kilometric radiation - Time-averaged source location

In the present paper, the location of the average generation region of auroral kilometric radiation is determined from an analysis of average electric field strengths as a function of spacecraft position in narrow frequency bands centered at 178, 100, and 56.2 kHz. Intense sources of power radiating at kilometric wavelengths are found near 65 degrees invariant latitude in the Northern and Southern Hemispheres, from 22 to 24 hours MLT, and between 2 and 4 earth radii. These dominant sources of power produce the electromagnetic radiation described by Kurth et al. (1975) as auroral kilometric radiation. Each Northern and Southern Hemisphere auroral kilometric radiation source is well confined and emits radiation into solid angles of about 4.1 sr at 178 kHz, 2.2 sr at 100 kHz, and 1.5 sr at 56.2 kHz.

Gallagher, D. L.↗
NASA NTRS1985

Microwave model prediction and verifications for vegetated terrain

To understand the scattering properties of a deciduous and a coniferous type vegetation scattering models were developed assuming either a disc type leaf or a needle type leaf. The major effort is to calculate the corresponding scattering phase functions and then each of the functions is used in a radiative transfer formulation to compute the scattering intensity and consequently the scattering coefficient. The radiative transfer formulation takes into account the irregular ground surface by including the rough soil surface in the boundary condition. Thus, the scattering model accounts for volume scattering inside the vegetation layer, the surface scattering from the ground and the interaction between scattering from the soil surface and the vegetation volume. The contribution to backscattering by each of the three scattering mechanisms is illustrated along with the effects of each layer or surface parameter. The major difference between the two types of vegetation is that when the incident wavelength is comparable to the size of the leaf there is a peak appearing in the mid angular region of the backscattering curve for the disc type leaf whereas it is a dip in the same region for a needle type leaf.

Fung, A. K.↗
NASA NTRS1987

Whistler mode emissions in the Uranian radiation belts

Voyager 2 detected intense whistler mode emissions and fluxes of energetic electrons during the outbound pass through the region of auroral L shells. The observed energetic (E greater than 22 keV) electron distribution, a model warm (E less than 27.5 keV) electron distribution, and the cold plasma density profile deduced by Kurth et al. (1987) are used to calculate the ray path-integrated spatial amplification of whistlers which arrive at Voyager 2 from the magnetic equator. By matching the calculated amplification and the relative gains at different frequencies deduced from the observed whistler power spectrum, the pitch angle anisotropy parameters of the electron distributions are determined to within a fairly narrow range of values. The estimated bounce average pitch angle diffusion coefficient indicates that electrons are on strong diffusion over a wide range in energies. The electron precipitation energy flux is sufficient to produce the observed auroral light emissions.

Coroniti, F. V.↗
NASA NTRS1994

Carbon recombination lines as a diagnostic of photodissociation regions

We have observed the C91 alpha radio recombination line toward the Orion H II region. This narrow (approximately 3-5 km per sec full width at half maximum (FWHM)) line is spatially very extended (approximately 8 arcmin or 1 pc). These charateristics compare well with the observed characteristics of the C II fine structure line at 158 microns. Thus, the C91 alpha line originates in the predominantly neutral photodissociation regions separating the H II region from the molecular cloud. We have developed theoretical models for the C II radio recombination lines from photodissociation regions. The results show that the I(C91 alpha)/I(C158) intensity ratio is a sensitive function of the temperature and density of the emitting gas. We have also extended theoretical models for photodissociation regions to include the C II recombination lines. Comparison with these models show that, in the central portion of the Orion region, the C91 alpha line originates in dense (10(exp 6) per cu cm), warm (500-1000 K) gas. Even at large projected distances (approximately 1 pc), the inferred density is still high (10(exp 5) per cu cm) and implies extremely high thermal pressures. As in the case of the (C II) 158 microns line, the large extent of the C91 alpha line shows that (FUV) photons can penetrate to large distances from the illuminating source. The decline of the intensity of the incident radiation field with distance from Theta(sup 1) C seems to be dominated by geometrical dilution, rather than dust extinction. Finally, we have used our models to calculate the intensity of the 9850 A recombination line of C II. The physical conditions inferred from this line are in good agreement with those determined from the radio recombination and the far-infrared fine-structure lines. We show that the ratio of the 9850 A to the C91 alpha lines is a very good probe of very high density clumps.

Natta, A.↗
NASA NTRS2009

Validity of the Aluminum Equivalent Approximation in Space Radiation Shielding

The origin of the aluminum equivalent shield approximation in space radiation analysis can be traced back to its roots in the early years of the NASA space programs (Mercury, Gemini and Apollo) wherein the primary radiobiological concern was the intense sources of ionizing radiation causing short term effects which was thought to jeopardize the safety of the crew and hence the mission. Herein, it is shown that the aluminum equivalent shield approximation, although reasonably well suited for that time period and to the application for which it was developed, is of questionable usefulness to the radiobiological concerns of routine space operations of the 21 st century which will include long stays onboard the International Space Station (ISS) and perhaps the moon. This is especially true for a risk based protection system, as appears imminent for deep space exploration where the long-term effects of Galactic Cosmic Ray (GCR) exposure is of primary concern. The present analysis demonstrates that sufficiently large errors in the interior particle environment of a spacecraft result from the use of the aluminum equivalent approximation, and such approximations should be avoided in future astronaut risk estimates. In this study, the aluminum equivalent approximation is evaluated as a means for estimating the particle environment within a spacecraft structure induced by the GCR radiation field. For comparison, the two extremes of the GCR environment, the 1977 solar minimum and the 2001 solar maximum, are considered. These environments are coupled to the Langley Research Center (LaRC) deterministic ionized particle transport code High charge (Z) and Energy TRaNsport (HZETRN), which propagates the GCR spectra for elements with charges (Z) in the range I <= Z <= 28 (H -- Ni) and secondary neutrons through selected target materials. The coupling of the GCR extremes to HZETRN allows for the examination of the induced environment within the interior' of an idealized spacecraft as approximated by a spherical shell shield, and the effects of the aluminum equivalent approximation for a good polymeric shield material such as genetic polyethylene (PE). The shield thickness is represented by a 25 g/cm spherical shell. Although one could imagine the progression to greater thickness, the current range will be sufficient to evaluate the qualitative usefulness of the aluminum equivalent approximation. Upon establishing the inaccuracies of the aluminum equivalent approximation through numerical simulations of the GCR radiation field attenuation for PE and aluminum equivalent PE spherical shells, we Anther present results for a limited set of commercially available, hydrogen rich, multifunctional polymeric constituents to assess the effect of the aluminum equivalent approximation on their radiation attenuation response as compared to the generic PE.

Badavi, Francis F.↗
DOE OSTI2022

Demonstration of an intense lithium beam for forward-directed pulsed neutron generation

Abstract As an alternative to research nuclear reactors, a compact accelerator-driven neutron generator that uses a lithium beam driver could be a promising candidate since it produces almost no undesired radiation. However, providing an intense lithium-ion beam has been difficult, and it has been thought that the practical application of such a device would be impossible. The most critical problem of insufficient ion fluxes has been solved by applying a direct plasma injection scheme. In this scheme, a pulsed high-density plasma from a metallic lithium foil generated by laser ablation is efficiently injected and accelerated by a radio-frequency quadrupole linear accelerator (RFQ linac). We have obtained a peak beam current of 35 mA accelerated to 1.43 MeV, which is two orders of magnitude higher than a conventional injector and accelerator system can deliver.

43 PARTICLE ACCELERATORS↗
NASA NTRS1988

A general-purpose computer program for studying ultrasonic beam patterns generated with acoustic lenses

A 3-D computer model of a piston radiator with lenses for focusing and defocusing is presented. To achieve high-resolution imaging, the frequency of the transmitted and received ultrasound must be as high as 10 MHz. Current ultrasonic transducers produce an extremely narrow beam at these high frequencies and thus are not appropriate for imaging schemes such as synthetic-aperture focus techniques (SAFT). Consequently, a numerical analysis program has been developed to determine field intensity patterns that are radiated from ultrasonic transducers with lenses. Lens shapes are described and the field intensities are numerically predicted and compared with experimental results.

Roberti, Dino↗
NASA NTRS1983

High latitude electromagnetic plasma wave emissions

The principal types of electromagnetic plasma wave emission produced in the high latitude auroral regions are reviewed. Three types of radiation are described: auroral kilometric radiation, auroral hiss, and Z mode radiation. Auroral kilometric radiation is a very intense radio emission generated in the free space R-X mode by electrons associated with the formation of discrete auroral arcs in the local evening. Theories suggest that this radiation is an electron cyclotron resonance instability driven by an enhanced loss cone in the auroral acceleration region at altitudes of about 1 to 2 R sub E. Auroral hiss is a somewhat weaker whistler mode emission generated by low energy (100 eV to 10 keV) auroral electrons. The auroral hiss usually has a V shaped frequency time spectrum caused by a freqency dependent beaming of the whistler mode into a conical beam directed upward or downward along the magnetic field.

Gurnett, D. A.↗
NASA NTRS1990

A procedure for the extraction of airglow features in the presence of strong background radiation

A technique is developed that can be used to derive the total intensity of band emissions from twilight airglow measurements when the basic spectral signature of the band to be considered is known. The method is designed to automatically extract total band or line intensities of a signal imbedded in background radiation several orders of magnitude greater in brightness. It is shown that the technique developed can reliably measure the intensity of both weak and strong band and line emissions in the presence of strong twilight background radiation. The method of extraction is shown as part of a general purpose spectral analysis program written in VAX FORTRAN. This extraction procedure has been used successfully on emissions of Fel, Ca(+), N2(+) (1N) (0-0) and (0-1), OH in the near UV. OI red (630nm) and green (558nm) lines in the visible, and the OH Meinel bands and O(+) (2P) 732 nm in the near IR.

Swift, W. R.↗
NASA NTRS1972

Environmental simulation from 0.01 to 100 solar constants

The design and development of two solar radiation simulators with an intensity variation ranging from 0.01 to greater than 100 solar constants under vacuum conditions are discussed. The characteristics of the simulators are presented in terms of spectral content, beam uniformity, and stability. Preliminary thermal radiative property data obtained at high temperatures are reported. The general operating characteristics of the simulator are automatic starting, control of both positive and negative electrodes, and uninterrupted operation for periods in excess of 24 hours.

Jack, J. R.↗