Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Porous flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Additively manufactured cryogenic microchannel distillation device for air separation

Abstract The efficiency of air separation is tested using three different small‐scale cryogenic distillation columns. The performance of a random packed column is compared to the performance of two microchannel distillation (MCD) columns that use thin wicking structures and gas flow channels to achieve process intensification. The MCD columns tested include a plate‐type layered column and an additively manufactured porous honeycomb (AMPH) column. For columns with 25.4 cm of active height and run under similar conditions, the packed, plate‐type layering, and AMPH columns achieved approximate height equivalent of a theoretical plate (HETP) values of 5.5, 3.7, and 3.2 cm for nitrogen, and 5.9, 4.9, and 3.3 cm for argon. The AMPH column can produce up to 0.4 SLM of more than 90% purity oxygen with 12 W of cooling lift. These results demonstrate the feasibility of using additive manufacturing to construct MCD devices and pave a way for constructing novel MCD designs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sintering inhibition enables hierarchical porosity with extreme resistance to degradation during redox cycling of Fe-Mo foams

High-temperature (800 ºC) steam-hydrogen redox cycling, relevant to grid-scale energy storage, is studied for iron-based freeze-cast lamellar foams. In contrast to previously studied Fe, Fe-Ni, and Fe-Co foams that rapidly degrade, Fe-25Mo foams feature a much-enhanced structural damage resistance. Utilizing in-situ x-ray diffraction, microscopy, and x-ray tomography, strong sintering inhibition is observed in Fe-Mo foams, creating a hierarchically porous lamellar structure. This leads to (i) wide channels between lamellae, enabling high macroscopic porosity (~78%) which can accommodate gas flow as well as volumetric expansion without lamellar contact, and (ii) microporosity within lamellae, providing additional free volume to accommodate expansion during oxidation, limiting both swelling of the lamellae and the formation of Kirkendall pores. Finally, these combined effects enable a near-complete reversibility of the microstructure during cycling, preventing damage produced via internal lamellar buckling, cracking, contacting and sintering, with a remarkably high porosity (65%) remaining after 50 consecutive redox cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A review of spatial Markov models for predicting pre-asymptotic and anomalous transport in porous and fractured media

Heterogeneity across a broad range of scales in geologic porous media often manifests in observations of non-Fickian or anomalous transport. While traditional anomalous transport models can successfully make predictions in certain geological systems, increasing evidence suggests that assumptions relating to independent and identically distributed increments constrain where and when they can be reliably applied. A relatively novel model, the Spatial Markov model (SMM), relaxes the assumption of independence. The SMM belongs to the family of correlated continuous time random walks and has shown promise across a wide range of transport problems relevant to natural porous media. It has been successfully used to model conservative as well as more recently reactive transport in highly complex flows ranging from pore scales to much larger scales of interest in geology and subsurface hydrology. In this review paper we summarize its original development and provide a comprehensive review of its advances and applications as well as lay out a vision for its future development.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of a Hybrid Single/Two-Phase Capillary-Based Micro-Cooler using Copper Inverse Opals Wick with Silicon 3D Manifold for High-Heat-Flux Cooling Application

Previously, we reported two-phase capillary-based cooling using narrow (200 to 1000 ..mu..m) heater bridge copper inverse opal (CIO) wicks with heat flux level of 1400 Wcm -2 and superheat ~ 10 degrees C. Here, we demonstrate the area scaling of the proposed technology to a large-area micro-cooler for high-heat-flux cooling of microprocessors and power electronics. We developed a hybrid single/two-phase micro-cooler that relies on capillary-wicking in a 25-..mu..m-thick CIO with an open silicon microchannel 3D-manifold for liquid delivery and vapor extraction, achieving a high heat flux ~ 400 Wcm -2 over a heated area of 10 x 10 mm 2 . For a range of inlet water flowrates from 5 to 60 g(min) -1 , we achieved total thermal resistances and vapor qualities of 0.68 cm 2 degrees CW -1 to 0.2 cm 2 degrees CW -1 and 0.55 to 0.12, respectively. The flowrates are 10x smaller than those of conventional single- or two-phase microchannel cooling technology. The corresponding two-phase thermal resistances ranges from 0.05 to 0.02 cm 2 degrees CW -1 with temperature superheat of 8 to 6 degrees C, respectively. While the overall performance of the large-area (10 x 10 mm 2 ) capillary-based micro-cooler degraded compared to the previous demonstration of the technology for a heated area of 5 x 5 mm 2 , however, preliminary CFD modeling indicates that an improved manifold design will be able to achieve comparable performance.

capillary flow↗
NASA NTRS1965

Unique gear design provides self-lubrication

Composite gear configuration provides a reliable automatic means for replenishing gear mechanism lubricants that dissipate in the harsh environment of space. The center or hub section of the gear consists of a porous, oil impregnated material, and the outer or toothed section has radially drilled passages to cause the oil to gradually flow to the gear teeth surface.

Winiarski, F. J.↗
NASA NTRS1985

Amorphous and porous ices in cometary nuclei

The heat flux into the cometary nucleus before and after perihelion and its influence on the nucleus are discussed. The surface temperature and the associated rate of evaporation are lower than usually calculated, and the effect is strongly dependent on the porosity of the nucleus. The surface temperature reaches a maximum after perihelion, in agreement with statistical studies of comae and tails. Delayed heating of the CO2-rich inclusions deep in the nucleus leads to outbursts and splittings as far as 9 AU after perihelion, also in agreement with observation. At sufficiently high temperatures, heat transport in porous cometary nuclei is controlled by vapor diffusion. The presence of CO2 vapor in the pores significantly increases the heat flow in mixed nuclei at temperatures above 140-150 C. Closed pores move up the radial thermal gradient so that the outside layer of a cometary nucleus should become denser.

Smoluchowski, R.↗
NASA NTRS1987

Performance test of a laboratory pump liquid transfer based on the fountain effect

A laboratory scale pump has been tested in detail in order to determine the flow characteristics of a heater-activated all-metal thermomechanical pump (fountain effect pump, FEP). The emphasis is on the functional dependence of the fountain pressure difference versus mass throughput. A modified Vote et al. (1971) power law approximation is employed for a simplified description of the flow rate as a function of the driving force. Flow rates of up to 10 liters/(hr/sq cm) have been obtained despite a large nominal pore size of the porous plug of 2 microns (filtration rating) used for the FEP.

Chen, W. E. W.↗
NASA NTRS1990

Kinetics and transport at AMTEC electrodes. I - The interfacial impedance model

Mixed mass-transport and kinetic control of sodium ion reduction at porous inert electrodes on sodium beta-double-prime alumina solid electrolyte (BASE) ceramic in a high-temperature electrochemical cell has been observed and modeled. The high ionic conductivity of BASE and the reversibility of the liquid sodium/BASE anodic half-cell led to assignment of potential-dependent (nonohmic) resistances to kinetic and mass-transport processes associated with the porous electrode. The morphology of these electrodes and typical sodium gas pressures are consistent with Knudsen, or free-molecular, flow through the electrode.

Williams, R. M.↗
DOE OSTI2024

Development of a Hybrid Single/Two-Phase Capillary-Based Micro-Cooler Using Copper Inverse Opals Wick with Silicon 3D Manifold for High-Heat-Flux Cooling Application: Preprint

Previously, two-phase capillary-based cooling from narrow (200-1,000 micrometer) heater-bridge copper inverse opal (CIO) wicks with heat flux levels exceeding 1,400 watts per square cm with a low superheat of approximately 10 degrees C was demonstrated. Here, we demonstrate the area scaling of the proposed technology to large-area micro-cooler for the high-heat-flux cooling of microprocessors and power electronics. We developed a hybrid single/two-phase micro-cooler that relies on capillary wicking in 25-micrometer-thick CIOs with an open channel silicon 3D-manifold for liquid delivery and vapor extraction, to achieve a high heat flux of approximately 400 watts per square cm over a heated area of 1 square cm. For the range of inlet water (21 degrees C water temperature) flowrates from 5 to 60 mL per min, we achieved total thermal resistances and vapor qualities of 0.68-0.2 square cm Kelvin per watt and 0.55-0.12, respectively. The high heat flux levels are achieved with flowrates that are 10 times smaller than conventional single- or two-phase microchannel cooling technology. The corresponding two-phase thermal resistances are in the range of 0.05 to 0.02 square cm Kelvin per watt with temperature superheat of 8 to 6 degrees C. While the overall performance of the large-area (10 by 10 square millimeter) capillary-based micro-cooler degraded compared to previous demonstration of the technology for a heated area of 5 by 5 square millimeter, preliminary computational fluid dynamics (CFD) modeling indicates that an improved manifold design will be able to achieve comparable performance.

capillary flow↗
NASA NTRS1988

Dewar to dewar model for superfluid helium transfer

A model has been developed to predict the flow of He II between a source and a receiving dewar. The model uses a finite difference aproximation to integrate the describing equations. The transfer path may contain porous plugs or mechanical pumps, heater sections, heat leaks, constrictions due to valves, and bends. These line elements may occur in any order and in any quantity. The line elements are easily reconfigured by changing the input data. The input consists of the number of finite element cells, the pressure in each dewar, the heat input to each section and the dimensions of each section. The output is the temperature, pressure, flow rate, velocities and heat flux in each section. An internal reference table provides the properties of He II. The model is programmed for a LOTUS work sheet. It converges rapidly and usually requires 10 to 15 iterations. For most applications an iteration takes 30 s on an AT. The predictions agree well with experimental data.

Snyder, H. A.↗
NASA NTRS1999

Distributed Pore Chemistry in Porous Organic Polymers in Tissue Culture Flasks

A method for making a biocompatible polymer article using a uniform atomic oxygen treatment is disclose. The substrate may be subsequently optionally grated with a compatibilizing compound. Compatibilizing compounds may include proteins, phosphorylcholine groups, platelet adhesion preventing polymers, albumin adhesion promoters, and the like. The compatibilized substrate may also have a living cell layer adhered thereto. The atomic oxygen is preferably produced by a flowing afterglow microwave discharge, wherein the substrate resides in a sidearm out of the plasma. Also, methods for culturing cells for various purposes using the various membranes are disclosed as well. Also disclosed are porous organic polymers having a distributed pore chemistry (DPC) comprising hydrophilic and hydrophobic regions, and a method for making the DPC by exposing the polymer to atomic oxygen wherein the rate of hydrophilization is greater than the rate of mass loss.

Koontz, Steven L.↗
DOE OSTI2024

A review of fluids under nanoconfinement: Reactivity, geomechanics, phase transitions, and flow

Due to its many industrial applications, the physics associated with the nanoconfinement of fluids has garnered great attention from the scientific community in roughly the last fifteen years. One pioneer of that research has been the Multi-Scale Fluid-Solid Interactions in Architected and Natural Materials (MUSE) Energy Frontier Research Center, which produced more than 50 journal articles from 2018 to 2023. We structure the findings of MUSE into four categories and contextualize the work with the broader literature. Here, the four categories are (1) the dependence of chemical reactions on the degree of confinement, which given the lower freedom of motion of molecules yet improved availability of reaction sites generally lead to enhancement from bulk reactions; (2) the mechanical properties of the porous matrix, which are dependent on the heterogeneity of the system in terms of both composition and structure; (3) the phase transitions under nanoconfinement, which are influenced by the pore size and morphology, surface chemistry, and substrate composition; and (4) the physical controls of slip flow, which demonstrate the importance of several factors, such as wettability. These aspects of nanoconfinement are becoming clearer, but there are other elements such as mathematical theory that are still being developed.

58 GEOSCIENCES↗
NASA NTRS1992

Water Relations, Gas Exchange, and Nutrient Response to a Long Term Constant Water Deficit

Wheat plants (Triticum aestivum) were grown for 43 days in a micro-porous tube nutrient delivery system. Roots were unable to penetrate the microporous tube, but grew on the surface and maintained capillary contact with the nutrient solution on the inside of the tube through the 5-microns pores of the porous tube. Water potential in the system was controlled at -0.4, -0.8, and -3.0 kPa by adjusting the applied pressure (hydrostatic head) to the nutrient solution flowing through the microporous tubes. A relatively small decrease in applied water potential from -0.4 to -3.0 kPa resulted in a 34% reduction of shoot growth but only a moderate reduction in the mid-day leaf water potential from - 1.3 to - 1.7 MPa. Carbon dioxide assimilation decreased and water use efficiency increased with the more negative applied water Potentials, while intercellular C02 concentration remained constant. The physiological responses observed in this study in response to small constant differences in applied water potentials were much greater than expected from either the applied water potential or the observed plant water potential. Even though the micro-porous tube may not represent natural conditions and could possibly introduce morphological and physiological artifacts , it enables a high degree of control of water potential that facilitates the investigation of many aspects of water relations not practical with other experimental systems.

Berry, Wade L.↗
DOE OSTI2021

Pore-scale simulation of drying in porous media using a hybrid lattice Boltzmann: pore network model

In this work, a hybrid method coupling a pseudo-potential lattice Boltzmann model (LBM) and a pore network model (PNM) to simulate drying in porous media is proposed. Based on the watershed method, the porous medium is firstly decomposed into pore regions. According to the liquid–vapor phase distribution at a given time, the pore regions are further divided into four pore types, namely two-phase pores where a liquid–vapor interface exists, buffer pores next to the two-phase pores, single-liquid and single-vapor phase pores. The pseudo-potential LBM is used in the two-phase and buffer pores to simulate liquid drying and track the movement of the interfaces, while the single-phase PNM simulations are conducted in the buffer and single-phase pores to simulate vapor or liquid flow. LBM and PNM are coupled in the buffer pores through exchange of boundary information. The hybrid method is applied to simulate liquid drying in a porous medium. The whole-domain LBM simulation is considered as the reference solution to validate the hybrid method. Liquid saturation variation during the drying process and detailed phase and pressure distributions obtained by the two methods match quite well, demonstrating the accuracy of the hybrid method. For the specific case studied, the hybrid method saves more than 60% computational time compared to the whole-domain LBM simulation. In addition, the speedup of the hybrid method becomes more significant for a larger computational domain. In summary, the hybrid method developed in this work combines the accuracy of LBM and the efficiency of PNM to simulate drying in porous media at pore scale and can lead to significant reduction of computation time, thus allowing the pore-scale consideration of drying in larger porous systems.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Heat transfer characteristics of porous media

An investigation was conducted regarding the relative effects of conduction and convection in a saturated porous medium. A method reported by Singh et al. (1973) is used to determine the effective thermal conductivity of the saturated porous material. Heat transfer measurements are conducted under conditions of forced convection of the saturated liquid parallel and countercurrent to the flow of heat. The results are compared with the data obtained with the aid of an analytical model.

Singh, B. S.↗
NASA NTRS1975

Dynamic oxidation behavior of TD-NiCr alloy with different surface pretreatments

Oxidation tests of TD-NiCr alloy with different surface pretreatments were conducted in a Mach-5 arc-jet at 1200 C and 0.002 lb/sec flowing air environment. The mechanisms responsible for the observed oxidation behavior are examined. The presence of atomic oxygen in the air stream plays a significant role in determining the oxidation characteristic of the alloy. The rate of Cr2O3 vaporization by formation of volatile CrO3 is greatly enhanced by the flowing conditions. The typical microstructure of oxides formed in the dynamic tests consists of an external layer of NiO with a porous mushroom-type morphology, an intermediate layer of NiO and Cr2O3 oxide mixture, and a continuous inner layer of Cr2O3 in contact with the Cr-depleted alloy substrate. Three basic processes underlying the formation of mushroom-type NiO are identified and discussed. The oxidation rate is determined by the rate of vaporization of NiO. Surface pretreatment has a significant effect on the oxidation behavior of the alloy in the early stage of oxidation, but becomes less important as exposure time increases. Mechanical polishing induces surface recrystallization, but promotes the concurrence of external growth of NiO and internal oxidation of the alloy in the dynamic atmosphere.

Young, C. T.↗