SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The new compound, Mo(OSiPH3)4 (where Ph is C6H5) was synthesized. An overall chemical reaction which accounts for the observed products is given by the redox approach. Results indicate that Mo(OSiPH3)4 is thermally stable up to 230 C and relatively unreactive toward most common acids and bases even at elevated temperatures. Its behavior is not unlike that of Ti(OSiPH3)4.
Preceramic polymer grafted nanoparticles (PCP GNPs) offer potential advantages in the production of polymer-derived ceramic composites compared to neat preceramic polymers (PCPs), such as reduced thermal shrinkage and increased char yield. In comparison to traditional composites (particles + free polymer), PCPs avoid issues of compatibility, agglomeration, and phase separation during processing and provide routes to control nanoparticle arrangement. Prior literature has established that the conversion efficiency of PCPs and PCP GNPs to ceramics and ceramic composites is linked to the thermal pretreatment of these precursor polymers (e.g., curing). In this paper, we investigate the material transformations that occur when exposing PCP GNPs to a low-temperature thermal treatment (≤250 °C) prior to pyrolysis. The PCP GNPs explored in this study possessed silica nanoparticle cores but were distinct in their PCP coronas, having poly(1,1-dimethylpropylsilane) (allyl-GNP)- or poly(1,1-dimethylbenzylethylsilane) (styryl-GNP)-grafted polymers. After undergoing low-temperature thermal treatment, these PCP GNPs exhibited increased char yield at 800 °C; however, unlike commercial PCPs (e.g., allylhydridopolycarbosilane (SMP-10)), obvious cross-linkable sites are not present in the PCP corona structure. Differential scanning calorimetry, oscillatory rheology, and X-ray photon correlation spectroscopy were utilized to elucidate the thermally induced material changes in the allyl- and styryl-GNPs. Thermally induced changes to the structure and behavior of the PCP GNPs were determined to be linked to the chemical structure of the grafted polycarbosilane chains. Styryl-GNPs experienced a curing event between 180 and 250 °C, effecting the formation of a network, which contributed to char yield improvement (at 800 °C). The nanoscale dynamics of this material also shows a transition from diffuse behavior to ballistic behavior because of the cross-linking event. Conversely, the allyl-GNPs did not exhibit a curing event under heat treatment but did show an increase in thermally induced physical cross-linking. The allyl-GNP physical network is stronger after the first cycle of thermal treatment, and it is considered that this contributed to the improvement in char yield post thermal treatment. The advancements in the understanding of the cross-linking behavior of these hybrid materials are expected to advance the application of these materials to turbine engine, advanced friction, and heat-shielding components.
The corrosion kinetics of metals in the presence of polymer electrolytes—which are often used in devices for the electrochemical production of hydrogen, hydrocarbons, and alcohols—is convoluted by transport and ill-defined reactive interfaces which mask the fundamental reaction kinetics. Underpotential-deposited monolayers of Cu at Au(111) surfaces provide a structurally welldefined active site for interfacial ion transfer, with a fixed number of sites available for adsorption. Here, we investigate the adsorption behavior of Cu at Au(111) surfaces across a series of sulfate and sulfonate electrolytes, to understand how anion structure influences the kinetics of elementary interfacial ion-transfer reactions. The influence of anion structure is most significant at high adsorbate coverage, with similar adsorption isotherms and kinetics observed for all three molecular sulfates and sulfonates. In contrast, a suspended perfluorosulfonic acid ionomer reduced both the equilibrium coverage of Cu as well as the standard exchange rate at Au(111) at low coverages of Cu. These results suggest that electrocatalyst corrosion is inhibited for metal nanoparticles supported at polymer electrolytes due to changes in adsorbate coverage as well as suppressed kinetics for interfacial ion transfer.
The manipulation and tunability of self-assembled block copolymers through external stimuli presents an attractive strategy to develop smart polymer-based nanoreactors as supports for non-orthogonal tandem catalysis. We report on thermoresponsive core-shell micelles based on poly[norbornene-poly(2-methyl-2-oxazoline-block-2-propyl-2-oxazoline)]-graft-poly[norbornene L-proline] (P[NB-P(MeOx-b-PropOx)]-graft-P[NB-L-proline]) as catalyst supports for L-proline. These molecular brushes exhibit large differences in lower critical solution temperature behavior and nanostructure size in water depending on the chain-lengths and proline connectivity. L-Proline-mediated aldol reactions expose the efficiency by which the molecular brushes self-assemble into micelles. Molecular brushes with an extended backbone show higher activity and selectivity, suggesting better core-shell segregation of the micelles and exclusion of water from the catalytic site. Catalytic efficiencies are not improved above the cloud point temperature, the catalytic be-havior is rather sensitive to conformational changes of the polymer chains.
In last few years, the rate of development and advances in the field of EAP has accelerated significantly and it is increasingly getting closer to the point of finding them used in commercial products. Substantial development has been reported in the understanding of their drive mechanisms and the parameters that control their electro-activation behavior. Further, efforts are being made to develop mass production techniques with greatly improved actuation capability and operation durability. The recent efforts to develop energy harvesting techniques, haptic interfacing (including refreshable braille displays), and toys are further increasing the likelihood of finding niches for these materials. In this paper, the author sought to examine the potential directions for the future development of the field of EAP in relation to the state-of-the-art.
Here, we study the phase behavior of a triblock organic–inorganic hybrid copolymer, poly(polyhedral oligomeric silsesquioxane)-b-poly(ethylene oxide)-b-poly(polyhedral oligomeric silsesquioxane) (POSS-PEO-POSS)/lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt mixture, as a function of temperature. The polymer exhibits a lamellar morphology both in the neat state and in the presence of salt. However, the average grain size increases substantially when the electrolyte is heated above 113 °C. The grain structure of this sample changes reversibly with temperature, that is, smaller grains reappear when the electrolyte is cooled below 113 °C. While annealing block copolymers at high temperatures often leads to an increase in the grain size, this change is generally irreversible. The reason for the reversible change in the grain structure of the POSS-PEO-POSS/LiTFSI electrolyte is discussed. The ionic conductivity of the electrolyte also exhibits reversible changes in this temperature window. Knowledge of the grain structure is crucial for understanding ion transport in nanostructured electrolytes.
Research and development in light-weight, high-temperature composite materials for ultrahigh-bypass engines to be used in high-speed civil transport/rotocraft is presented. It is noted that the expected benefits to be attained by this R&D include weight reduction, lowered fuel consumption, and lower direct operating costs. A major effort underway in this area is the Advanced High Temperature Engine Materials Technology Program (HITEMP) of NASA, which focuses on providing revolutionary high-temperature composite materials: to 425 C (800 F) for polymer-matrix composites (PMCs), to 1250 C (2280 F) for metal-matrix/intermetallic-matrix composites (MMCs/IMCs), and to as high as 1650 C (3000 F) for ceramic-matrix composites (CMCs). Analytical modeling is being used to investigate the structural behavior of these advanced materials in six distinct areas: micromechanics, deformation and damage, fatigue, fracture, trade-off studies, and load definition. It is concluded that the development of advanced materials such as high-temperature composites is highly dependent on the availability of high-temperature fibers. The wide range of fiber characteristics needed will require the development of more than one fiber. In general, a candidate fiber should have low density, high strength, high stiffness, a CTE matching the matrix, chemical compatibility with the matrix, environmental stability and appropriate fiber diameter.
The present investigation examines the in-plane mechanical behavior of a particular woven metal matrix composite (MMC); 8-harness (8H) satin carbon/copper (C/Cu). This is accomplished via mechanical testing as well as micromechanical modeling. While the literature is replete with experimental and modeling efforts for woven and braided polymer matrix composites, little work has been done on woven and braided MMC's. Thus, the development and understanding of woven MMC's is at an early stage. 8H satin C/Cu owes its existence to the high thermal conductivity of copper and low density and thermal expansion of carbon fibers. It is a candidate material for high heat flux applications, such as space power radiator panels. The experimental portion of this investigation consists of monotonic and cyclic tension, compression, and Iosipescu shear tests, as well as combined tension-compression tests. Tests were performed on composite specimens with three copper matrix alloy types: pure Cu, Cu-0.5 weight percent Ti (Cu-Ti), and Cu-0.7 weight percent Cr (Cu-Cr). The small alloying additions are present to promote fiber/matrix interfacial bonding. The analytical modeling effort utilizes an approach in which a local micromechanical model is embedded in a global micromechanical model. This approach differs from previously developed analytical models for woven composites in that a true repeating unit cell is analyzed. However, unlike finite element modeling of woven composites, the geometry is sufficiently idealized to allow efficient geometric discretization and efficient execution.
The purposes of this study were to evaluate the growth of the surface damage layer in polymer matrix composites (PMC's) fabricated with graphite fabric reinforcement and to determine the effects of the cut-surface degradation on the overall thermo-oxidative (TOS) stability of these materials. Four important conclusions were made about the TOS behavior of T650-35/PNIR- 15 fabric-reinforced composites: (1) Three stages of composite weight loss were seen on the plot of weight loss versus aging time; (2) the depth of the cut-edge damage is related to the composite thickness; (3) the actual weight loss realized by a mechanical test specimen that has had all the aging-induced cut-edge damage removed during the preparation process is significantly less than the weight loss measured using specimens with a high percentage of cut edges exposed to the damaging environment; and (4) an extrapolation of a section of the weight loss curve can be used to obtain a more correct estimate of the actual weight loss after extended periods of aging at elevated temperatures.
Solid-state batteries (SSBs) fabricated using sulfide solid electrolytes (SSEs) typically require cell stack-pressures in the range of tens to hundreds of megapascals to maintain effective interfacial contact and lithium-ion mobility across the full cell stack. These relatively high cell stack-pressures necessarily require additional cell components that reduce the delivered volumetric and gravimetric capacities of SSBs. This work has developed a novel sulfur polymer (polyS) that improves lithium-ion conductivity in SSBs at low cell stack-pressures, thereby directly targeting this technological limitation. Specifically, this work shows that polyS can be combined with the argyrodite Li6PS5Cl (LPSC) to form a stable composite SSE. By combining LPSC particles with a flexible additive that enhances interfacial contact at low pressures, this new polyS LPSC composite SSE material greatly improves ionic conductivity at cell stack-pressures below 2.0 MPa in comparison to conventional LPSC composites. Furthermore, this polyS LPSC composite can be used to fabricate a full SSB that cycles reversibly at only 1.6 MPa. Finally, this composite SSE exhibits self-healing behavior when combined with a lithium metal electrode, wherein lithium dendrites are oxidized to form passivating Li2S species that recover the cell from shorting.
Pt catalysts in polymer electrolyte fuel cells degrade heterogeneously as the catalyst particles are exposed to local variations throughout the catalyst layer during operation. State-of-the-art analytical techniques for studying degradation of Pt catalysts do not possess fine spatial resolution to elucidate such non-uniform degradation behavior at a large electrode level. A new methodology is developed to spatially resolve and quantify the heterogeneous Pt catalyst degradation over a large area (several cm ) of aged MEAs based on synchrotron X-ray microdiffraction. PEFC single cells are aged using voltage cycling as an accelerated stress test and the degradation heterogeneity at a micrometer length scale is visualized by mapping Pt catalyst particle size after voltage cycling. It is demonstrated in detail that the Pt catalyst particle size growth is non-uniform and follows the flow field geometry. The Pt particle size growth is greater in the area under the flow field land, while it is minimal in the area under the flow field channel. Additional non-uniformity is observed with the Pt particle size increasing more rapidly at the air outlet area than the Pt particle size at the inlet area.
Here, the present article focuses on the development of a highly ion-conductive, solvent-free, solid-state polymer electrolyte membrane (PEM) via photopolymerization of polyethylene glycol diacrylate (PEGDA) network from its homogeneous melt mixtures containing succinonitrile (SCN) plasticizer and magnesium bis(trifluoromethane sulfonyl) imide Mg(TFSI) 2 salt. The above solid-state Mg-PEM exhibits a Helmholtz electric double-layer capacitor (EDLC) behavior in its supercapacitive symmetric carbonaceous electrode configuration. The electrochemical stability for this PEM membrane (20/40/40 PEGDA/SCN/Mg (TFSI) 2 ) was found to be approximately 3 V from linear sweep voltammetry with a specific capacitance of about 44 F/g from cyclic voltammetry and an energy density of approximately 17 Wh/kg in the 0–2 V range from the constant current density (CCD) experiment. Of particular interest is its excellent capacity retention of over 11,200 cycles, thus tested with the Coulombic efficiency of over 87%. Moreover, the energy density after extensive cycling for 11,200 has increased to approximately 56 Wh/kg at 10 mV/s in the potential range of 0–3 V relative to 17 Wh/kg in the potential range of 0–2 V at the same scan rate, attesting the excellent electrochemical stability and long life of the present Mg-PEM supercapacitor.
Abstract Elastomeric polymer materials hold a special place in today’s industrial sectors with respect to structural application needs. Low quality materials are detrimental to industries like aerospace, and automotive engineering. Assessment of the durability of elastomers for structural applications has been of much interest among the literary circles for decades and new materials keep outperforming the existing ones. Polymeric adhesives are one of the most abundantly used materials in these industries. All polymeric materials get damaged when in contact with aggressive environments in presence of high temperature and oxygen. Commonly referred to as thermo-oxidation, this environment exposes the material to heat and oxidation reactions in presence of oxygen. Resultantly, during service life, the damage to the polymer matrix is primarily caused by two factors: mechanical damage and environmental aging. Environmental aging is an irreversible phenomenon caused by changes in the molecular structure while mechanical damage maintains the shape of the polymer matrix, and the deterioration is mostly due to polymer chain mobility. Environmental aging can be caused by a single environmental agent or by a synergized impact of several environmental elements. Increasing temperature is found to be proportional to decreasing tensile strength and toughness of material. The rate and extent of degradation can be accessed by scrutinizing the changes in constitutive behavior of material through mechanical and chemical properties. Accelerated thermal aging is among the most common modes of process related degradation, leading generally to chain scission, and crosslinking phenomena and reduced resistance to fracture stress, and strain. In this experimental study, our goal is to separate the environmental degradation from mechanical damage. A silicone-based adhesive was aged in thermo-oxidative at (0%RH) aging environment. The damage and decay mechanisms have been used to draw a distinction between environmental degradation and mechanical damage. Material characterization included uniaxial tensile test (failure and cyclic) and scanning electron microscopy (SEM) tests on as-received and aged samples. Aging was conducted at three different temperatures (60°C, 80°C and 95°C) and six different exposure durations (1, 3, 10, 30, 90 and 200 days). This work confirms that environmental damage is superposed on top of the mechanical damage, and thus, they are separable. The total mechanical and environmental damage is a synergized effect of all exposure conditions and parameters involved i.e., aging time, temperature, and oxygen. The chemistry and mechanics of the polymer degradation were found to be in good agreement with each other.
While an organically modified chalcogenide (ORMOCHALC) can be used to fabricate a polymeric mid-wavelength infrared (MWIR) polarizer with competitive extinction ratio compared to the commercial wire-grid polarizers, which are composed of fragile inorganic materials, there is still a knowledge gap regarding the systematic design process to obtain high transmission efficiency and extinction ratio. As such, a computational parameter study for design optimization is conducted with the geometric parameters of the bilayer grating ORMOCHALC polarizer. The computational study shows that the Fabry–Pérot cavity is the primary mechanism that determines the transmission behaviors and the extinction ratio. A bilayer grating design, guided by the parameter study, is realized through the thermal nanoimprint and metal deposition processes. The extinction ratios measured with the Fourier-transform infrared are 245, 304, and 351 at the wavelength of 3, 4, and 5 μm, respectively. Compared to the state-of-the-art of the polymeric MWIR linear polarizers, the extinction ratio is improved by 1.4 times, and the transmission efficiency is increased by 2.5 times. Theoretical analysis with the multiple-layer model based on the transfer matrix method predicts a matched transmission behavior with the experiment and a full-wave electromagnetic simulation.
Segmented polyureas (PUa) are industrially important class of polymers widely used in coatings, sealant, and adhesive applications. Here, in this paper, we report synthesis, characterization, and modeling of Isophorone Diisocyanate-Diethyl-Toluene-Diamine-Polyether amine (IPDI-DETDA-PO PUa) with varied hard segment contents of 20, 30, and 40 weight percent. For each of the three materials, we study its structure and phase behavior using FTIR, DSC, and TEM, and clearly show the presence of microphase separation between the hard and soft nanodomains. We then measure the linear viscoelastic response of the PUa-s using DMA (frequency sweeps at multiple temperatures). The DMA data are shown to obey the time-temperature superposition. Finally, we develop a new micromechanical model describing the DMA results; the model describes a phase-separated PUa as two “Fractional-order Maxwell gels” branches, connected in parallel, with the first FMG branch representing the “percolated hard phase" and the second one modeling the “filled soft phase". In agreement with the earlier thermodynamic theories, the volume-fraction of the percolated hard phase is related to the hard segment weight-fraction (HSWF), defined as the combined mass of IPDI and DETDA normalized to the total mass of the polymer. The data and model are found to be in a good qualitative and quantitative agreement.
Selective ion separations are increasingly needed to combat water scarcity, recover resources from wastewater, and enable the efficient recycling of electronics waste. Emulsion liquid membranes (ELMs) have received interest due to rapid kinetics, high selectivities, and low solvent requirements but are too unstable for industrial usage. Here, we demonstrate that polymeric microcapsules can serve as robust, solvent-free mimics of ELMs. As a proof of concept, we incorporated the copper-selective ligand Lix 84-I in the walls of microcapsules formed from a commercial polystyrene-b-polybutadiene-b-polystyrene triblock polymer. The microcapsules were formed from a double-emulsion template, resulting in particles typically 20–120 μm in diameter that encapsulated even smaller droplets of a dilute (≤0.5 M) H 2 SO 4 solution. Batch experiments demonstrated facilitated-transport behavior, with equilibrium reached in as little as 10 min for microcapsules with 1% ligand, and with ~15-fold selectivity for Cu 2+ over Ni 2+ . Furthermore, the microcapsules could be packed readily in columns for flow-through operation, thus enabling near-complete Cu 2+ removal in ~2 min under certain conditions, recovery of Cu 2+ by flowing through fresh dilute H 2 SO 4 , and reuse for at least 10 cycles. The approach in this work can serve as a template for using selective ligands to enable robust and simple flow-through processes for a variety of selective ion separations.
The effects of salt-doping on the morphological behavior of block copolymers are well established but remain poorly understood, partially because of the challenge of resolving electrostatics in a heterogeneous medium with low average permittivity. By employing a recently developed field theory, we analyze the phase behavior of polystyrene-b-poly(ethylene oxide) (SEO) copolymers doped with lithium bis(trifluoromethanesulfonyl)imide salts (LiTFSI). Using a single fitting parameter, the ionic solvation radius, we obtain qualitative agreement between our theory and experimental data over a range of polymer molecular weights and copolymer compositions. Such agreement supports and highlights the need of solvation free energy to accurately describe the self-assembly of ion-doped block copolymers and demonstrates that experimentally observed dependence on molecular weight, not present in neutral block copolymers, can be rationalized by solvation effects. Overall, morphological variations are stronger than those predicted by the leading, linear order theory but can be captured by the full model.
Phosphoric acid loss poses immense hurdles for the durability of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs). Here we report quaternary ammonium-biphosphate ion-pair HT-PEMFCs that do not lose phosphoric acids under normal and accelerated stress conditions. Additionally, our energetics study explains the acid loss behavior of the conventional phosphoric acid-polybenzimidazole (PA-PBI) system by two mechanisms. If PA loss occurs via acid evaporation, the acid loss is constant over time. On the other hand, when water activity in the PA-PBI system is high, exponential decay of PA loss occurs via the water replacement mechanism. Combined 31 P NMR and computational studies show that the proposed ion-pair system has six times higher interaction energy, which allows for containing all PAs in the membrane electrode assemblies under a broad range of operating conditions. In addition, polar interactions between the phosphonic acid ionomer and phosphoric acid explain acid retention in the electrodes of the ion-pair HT-PEMFCs.