Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Functionally Graded W-Cu Materials Prepared from Cu-Coated W Powders by Microwave Sintering

Three-layered W-Cu (W-10Cu/W-20Cu/W-30Cu, weight percentage) functionally graded materials were fabricated by laminate pressing of Cu-coated W composite powders with different Cu contents (10-30 wt.% Cu) and W particle sizes in the powders and microwave sintering of the powder compacts. The microstructure and the physical and mechanical properties of the graded materials were investigated. The experimental results show that the relative density of the graded W-Cu samples sintered at 1250 °C for 20 min is above 97%. Cu has a gradient layer distribution in the thickness direction, and there is good combination between the layers in the graded samples. Furthermore, the graded W-Cu materials exhibit good physical and mechanical properties. The sintered samples have thermal conductivities above 210 W m K{sup −1}, and the maximum bending strength and hardness reach 1004 MPa and 346 HV, respectively. The present results show that functionally graded W-Cu materials with high density, gradient Cu and W distribution, and good properties can be successfully prepared by laminate pressing and microwave sintering.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Oxidation Resistance in 1200°C Steam of a FeCrAl Alloy Fabricated by Three Metallurgical Processes

Abstract FeCrAl alloys are a leading candidate material for accident tolerant fuel cladding due to their good performance in both normal light-water reactor operating conditions as well as their resilience to high-temperature accident scenarios. For commercial-scale production, new fabrication techniques need to be investigated. In this study, the effects of fabrication methods on the high-temperature steam oxidation performance of C26M (Fe12Cr6Al2Mo in wt.%) were investigated. Three variants of C26M were manufactured: wrought (cast and forged) (WC26M), powder metallurgy hot isostatic pressing (PMC26M), and laser powder bed fusion additive manufacturing (AMC26M). All three variants were exposed to steam at 1200°C for 2 h. Results showed no significant variation in mass change between the variants after steam exposure. All three variants effectively formed stable protective alumina films with ~0.6–1.3 µ m thickness. This study suggests FeCrAl alloys have excellent resilience to high-temperature steam in nuclear reactor accident scenarios regardless of the fabrication method.

Materials Science↗
DOE OSTI2020

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Densification and microstructure features of lithium hydride fabrication

The manufacturing of lithium hydride (LiH) utilizing uniaxial pressing, which offers fabrication with tailorable properties via microstructure control, can lead to the expansion in application of LiH while bypassing the challenges presented by historical casting manufacturing techniques. Through control of consolidation conditions such as pressure, temperature, dwell time and powder load, the presented work highlights the densification of LiH, with an emphasis on quantifying oxygen content, for applications requiring a specific density range necessary for optimized material performance. Karl Fischer Titration and X-ray Diffraction proved useful in determining oxygen and phase content while Computed Tomography and Scanning Electron Microscopy provided structural analysis. The temperature dependent densification of LiH fit with an Arrhenius term resulted in an activation energy of 21.2 kJ/mol. Images of fractured surfaces of LiH pressed at 500 °C revealed drastic grain coarsening, aided by the presence of oxygen impurities.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microwave assisted heating of plastic waste: Effect of plastic/susceptor (SiC) contacting patterns

We discuss plastic accumulation as a growing sustainability challenge. Most plastics are thermally inert at room temperature, requiring high temperatures for depolymerization. In the quest for developing sustainable plastic upcycling, we investigate silicon carbide (SiC) as microwave absorbing susceptors for reaching depolymerization temperatures. We utilize three SiC topologies – particles, hot-pressed plastic films containing SiC particles, and monoliths. SiC particles of >0.5 mm in diameter can provide heating rates approaching ~200 °C/min at modest powers. Still, physically mixed plastic-susceptor beds suffer from density differences, causing non-uniform contact during plastic softening and melting. Hot-pressed plastic films containing SiC particles allow uniform plastic-susceptor contact but suffer from slow heating as only a single layer of susceptors exists between polymer layers. SiC monoliths mitigate these challenges by preferentially dissipating the microwaves and rapidly heating the plastics independently of polymeric properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of lot microstructure variations on detonation performance of the triaminotrinitrobenzene (TATB)-Based insensitive high explosive PBX 9502

PBX 9502 is an important insensitive high explosive due to its combination of safety properties and detonation performance. It is a polymer-bonded formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the high explosive crystal, bound with Kel F-800 (FK-800), a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Two different types are used, one known as virgin that uses only pristine manufactured TATB, and a second known as recycled that has 50 wt.% of its TATB reclaimed from machining scraps of previously pressed virgin PBX 9502. Recycled lots have a higher percentage of fine particles compared to virgin lots, due to the fracturing and damage sustained by TATB crystals during pressing. We examine the influence that this TATB microstructure difference between virgin and recycled PBX 9502 has on detonation performance properties. New rate-stick geometry diameter effect, detonation front shape and cylinder expansion test data are obtained for two previously uncharacterized virgin lots and one recycled lot of PBX 9502. This is combined with previously published data for one virgin and one recycled lot for evaluation purposes. Detonation shock dynamics model calibrations are conducted on each of the five lots to provide an assessment of the detonation timing characteristics of virgin versus recycled PBX 9502 lots. For two of the virgin lots, detonations propagate slower in the rate-stick geometry than those in the two recycled lots. However, the other virgin lot tested has propagation rates comparable to that of the recycled lots for larger diameter rate-sticks. The latter result, though, is shown to be geometry dependent and depends on the range of detonation curvatures accessed in different geometries. New copper-confined, cylinder expansion tests are conducted on each of the three virgin and two recycled lots to obtain detonation product Jones-Wilkins-Lee equations of state, enabling an assessment of the metal push capabilities for each of the five lots. We find that the metal push capabilities, characterized by the evolution of the heat of detonation with volume, are similar between the virgin and recycled lots. Thus, changes in microstructure between different PBX 9502 lots seemingly affect the rate of reaction, but not the overall energy content.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Electrical property enhancement of non-heat-treatable wrought aluminum alloys using graphene additives

With growing efforts of electrification, aluminum’s role as a light-weight conductor material has become increasingly prominent. There is a critical need to improve the electrical performance of aluminum at room temperature and high operating temperatures. In this study, the effect of graphene nanoparticle additives on the electrical performance of a non-heat treatable alloy were (AA3003) explored. Graphene’s unusual structure and electronic properties were used to improve AA3003 properties. Here, in this work, the effects of graphene on the evolution of electrical properties and microstructural features have been explored on lab scale hot extruded AA3003-graphene composites. Hot pressing schedules and extrusion temperatures were varied to investigate changes in intermetallic dispersion characteristics in the presence of dispersed graphene. We measured a reduction of 10.3 % in the temperature coefficient of resistance in the AA3003 sample with 0.05 wt% graphene extruded at 400 °C, along with a maximum increase of 1.1 % in electrical conductivity at 20 °C. Increasing the hot-pressing times up to 8 hours was also found to consistently increase the electrical conductivity, due to increased precipitation of intermetallic phases. Despite being a non-heat treatable alloy, AA3003 displays interesting precipitation dynamics and grain recrystallization trends that can be modulated with varying levels of heat treatment, graphene concentrations, and hot extrusion process parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Reaction-bond composite synthesis of SiC-TiB 2 by spark plasma sintering/field-assisted sintering technology (SPS/FAST)

High-density SiC-TiB 2 composites were fabricated using the displacement reaction spark plasma sintering/field-assisted sintering technology (SPS/FAST) and SiC, B 4 C, TiC, and Si powders. The reaction process was performed in a narrow time frame compared hot pressing. The SiC-TiB 2 composites were sintered with precursor SiC at various pressures to determine the effects of processing with SPS/FAST. The composites completed synthesis during SPS/FAST processing, which occurs more quickly than hot pressing. SEM, STEM, and Raman spectroscopy are used to show the conversion and microstructure. Finally, the composite of 53.6 wt.% SiC and 46.4 wt.% TiB 2 has 99 % theoretical density, hardness of 26.4 GPa, and fracture toughness of 5.12 MPa m 1/2 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fast-rate joining of thermoplastic composites using integrated additive manufacturing and compression molding process

The integration of additive manufacturing (AM) technology with compression molding (CM), has emerged as a high-performance composite manufacturing technology in recent years. In the AM-CM process, quickly deposited AM preform on a mold undergoes a rapid compaction cycle to fabricate structurally robust composite parts due to highly controlled fiber alignment (from AM) and reduced porosity (from CM). Currently, AMCM-based part size is limited by the size of the mold volume, thus posing a challenge to manufacture scalable parts. Here, this work focuses on joining techniques developed to enable fast rate joining of short fiber-reinforced thermoplastic composite parts using the AM-CM process. Acrylonitrile butadiene styrene resin reinforced with 20 wt% short carbon fiber composites was printed onto a flat mold and pressed under a hydraulic press. Fabricated panels were joined by the (a) mechanical impression at the joining interface and (b) over-molded continuous carbon fiber (CCF) sheet. Tensile tests were performed to characterize the joining strength of both mechanical impression-based joints and CCF over molded joints. Among the mechanical impression-based joints, a U-shape channel allowed the fibers to flow between two joint parts, and 280 % increased mechanical properties were observed. The continuous carbon fiber-based over molded joint CCF showed 350 % increase in tensile strength compared to the butt joints.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Glass-bonded iodosodalite waste form for immobilization of 129I

Immobilization of radioiodine (e.g., 129I, 131I) is an important need for current and future nuclear fuel cycles. For the current work, iodosodalite [Na8(AlSiO4)6I2] was synthesized hydrothermally from metakaolin, NaI, and NaOH. Following hydrothermal treatment, dried unwashed powders were used to make glass-bonded iodosodalite waste forms by heating pressed pellets at 650, 750, or 850 °C with two different types of sodium borosilicate glass binders, i.e., NBS-4 and SA-800. These heat-treated specimens were characterized with X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, energy dispersive spectroscopy, thermal analysis, porosity and density measurements, neutron activation analysis, and inductively-coupled plasma mass spectrometry. The pellets mixed with 10 mass% of NBS-4 or SA-800 and heat-treated at 750 °C contained relatively high percentage iodine retention (~44-47 % of the maximum iodine loading) with relatively low porosities, while other pellets with higher percentages iodine retention either contained higher porosity or were not completely sintered. ASTM C1308 chemical durability tests of monolithic specimens showed a large initial release of Na, Al, Si, and I on the first day, possibly from water-soluble salt crystals or non-durable amorphous phases. Release rates of Na and Si were higher than for Al and I, probably due to a poorly durable Na-Si-O phase from the glass bonding matrix. The cumulative normalized release of iodine was 12.5 g m-2 for the first 10 1-d exchanges, suggestive of coherent dissolution. The average release rate from 10-24 days during the 7-d exchange intervals was 0.2336 g m-2 d-1.

sodalite, iodosodalite, waste forms, iodine↗
DOE OSTI2025

UO2 microstructural evolutions induced by Ni, Mo, and W dopants for intentional forensics

The concept of tagging nuclear fuel with a chemical barcode to enable forensics analysis across the nuclear fuel cycle is an area of active investigation, particularly to ensure fabrication viability without disrupting current fuel performance. This study explored the feasibility of using Ni, Mo, and W isotopic double-spikes as dopants in UO2 fuel from the perspective of fuel fabrication. Doped UO2 pellets were produced using conventional fuel fabrication processes, including powder mixing, sieving, pressing, and sintering in a reductive atmosphere. Two composition levels, 100 and 1000 ppm, were evaluated for each dopant element with isotopic double-spike configurations. For the Ni system, additional dopant concentrations of 250 and 500 ppm were produced with nonperturbed isotopic ratios. The results demonstrated that successful incorporation of Ni, Mo, and W double-spikes into UO2 pellets occurred with minimal shift in final density or dopant loss during pellet fabrication. Isotopic analysis confirmed the presence of the double-spike signature even when diluted with natural isotopic material in ratio of 1:5 in the fabrication process. Microstructural examinations revealed different impacts on grain size compared with undoped UO2. This study showed that Ni incorporation up to ∼500 ppm promoted moderate grain growth, whereas the Mo and W systems caused grain size reduction at all concentrations. Changes in the UO2 lattice parameter as a function of composition were detected exclusively for Ni up to 500 ppm, indicating that the Ni solid solution was the main factor for the observed grain growth. Insoluble (Mo and W) or supersaturated (Ni > 500 ppm) conditions produced grain size reduction. The Ni-doped pellets in the solution range resulted in a final microstructure within fuel specifications, demonstrating its potential benefits of employing complex dopant systems for potential nuclear forensic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Rational anode design for protonic ceramic fuel cells by a one-step phase inversion method

A one-step phase inversion method was applied to fabricate an optimized anode structure for protonic ceramic fuel cells (PCFCs). The phase inversion process utilized raw starting chemicals, instead of crystalline BaCe 0.7 Z r0.1 Y 0.1 Yb 0.1 O 3-δ (BCZYYb) powder in an energy and time saving process. The resulting large and fingerlike pores exhibited enhanced performance as compared to the disordered pores produced by conventional preparation of anode structures using dry pressing methods. The electrochemical performance of the rational designed anode supported cell were 491, 402, 302 and 200 mW cm -2 at 700, 650, 600 and 550 °C, respectively, which was nearly twice than the cell with dry pressing anode. An equivalent circuit modeling method was used to separate the anode polarization resistance from the single cell, confirming that the overall cell performance improvements were attributed to microstructural modifications of the anode by the phase inversion process. The one-step phase inversion method demonstrated great promise for improved processing of fuel cells and separation membranes.

25 ENERGY STORAGE↗
DOE OSTI2020

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2012

Alternative route for the preparation of CoSb{sub 3} and Mg{sub 2}Si derivatives

An alternative manufacturing route has been developed for cobalt triantimonide and magnesium disilicide derivatives. Elemental powders were mixed in stoichiometric proportions, cold pressed into cylindrical preforms and heated in oxygen-free environment to initiate the exothermic reaction. According to DTA/TG measurements and observations under high-temperature microscope, the onset of reaction occurred at a temperature not exceeding the melting point of the more volatile component, i.e. antimony in the case of CoSb{sub 3} and magnesium in the case of Mg{sub 2}Si. The reaction products were additionally heat treated to secure homogenization. Dense sinters were obtained by hot uniaxial pressing of the obtained powders in moderate temperature-and-pressure conditions. Several advantages were identified in the proposed technology: absence of liquid phases, relatively short time of the synthesis, possibility of in-situ or ex-situ doping and grain size control. - Graphical abstract: (1) Manufacturing flow sheet for CoSb{sub 3} (milling included) and Mg{sub 2}Si (no milling). (2) Micrographs of CoSb{sub 3} product. (3) Micrographs of Mg{sub 2}Si product. Highlights: Black-Right-Pointing-Pointer The combustion synthesis followed by HP was used for the manufacturing of CoSb{sub 3} or Mg{sub 2}Si. Black-Right-Pointing-Pointer The time of reaction is shorter compared with many other synthesis methods. Black-Right-Pointing-Pointer The process is scalable and practically wasteless.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Evaluation of microstructure anisotropy on room and medium temperature ECAP deformed F138 steel

The microstructure developed during severe plastic deformation results in improved mechanical properties because of the decrease in domain sizes and accumulation of defects, mainly dislocation arrays. The characteristic deformation stages observed in low stacking fault energy (SFE) face centered cubic (FCC) materials are highly influenced by the development of the primary and secondary twinning that compete with dislocation glide. In this paper, a low SFE F138 stainless steel is deformed by equal channel angular pressing (ECAP) up to 4 passes at room temperature (RT) and at 300 °C to compare the grain refinement and twin boundary development with increasing deformation. Tensile tests were performed to determine the deformation stages reached by the material before and after ECAP deformation, and the resulting microstructure was observed by TEM. X-ray diffraction and EBSD, average technique the first and local the second one, were used to quantify the microstructural changes, allowing the determination of diffraction domain sizes, dislocation and stacking fault densities and misorientation indices, which lead to a complete analysis of the deformation introduced in the material, with comparative correlations between various microstructural parameters. - Highlights: • The microstructure of ECAP pressed F138 steel was studied using TEM, EBSD and XRD. • Increasing deformation reduced domain sizes and increased dislocation densities. • Dislocation array compactness and misorientation increased with higher deformation. • Largest dislocation densities, mostly screw, match with simultaneous activation of twins. • Several correlations among microstructural features and parameters have been disclosed.

36 MATERIALS SCIENCE↗
DOE OSTI2011

High-temperature stability of {alpha}-Ta{sub 4}AlC{sub 3}

Graphical abstract: In this study, stability of {alpha}-Ta{sub 4}AlC{sub 3} is investigated to test a hypothesized thermodynamically driven {alpha}-{beta} phase transformation. It is found that the {alpha} phase is stable up to 1600 {sup o}C, with impurities and point defects most likely increasing the stability of the {alpha}-Ta{sub 4}AlC{sub 3}. Highlights: {yields} Cold-pressed {alpha}-Ta{sub 4}AlC{sub 3} powders are annealed up to 1750 {sup o}C to test first-principles predictions of {alpha}-{beta} phase-stability reversal at 1600 {sup o}C. {yields} The {alpha}-Ta{sub 4}AlC{sub 3} samples are stable up to 1600 {sup o}C, with no indications of any {alpha}-{beta} transformation. {yields} Transmission electron microscopy shows zig-zag stacking sequence characteristic of {alpha}-Ta{sub 4}AlC{sub 3}, as well as tantalum oxide impurities. {yields} The XRD patterns suggest that defects such as vacancies or antisites may increase the stability of {alpha}-Ta{sub 4}AlC{sub 3}. -- Abstract: Cold-pressed {alpha}-Ta4AlC3 powders were annealed up to 1750 {sup o}C to test first-principles predictions of {alpha}-{beta} phase-stability reversal at 1600 {sup o}C. Up to 1600 {sup o}C, the {alpha}-Ta{sub 4}AlC{sub 3} samples were stable with no indications of any {alpha}-{beta} transformation, as shown by the strong characteristic X-ray diffraction peaks of {alpha}-Ta{sub 4}AlC{sub 3} and the zigzag stacking observed by transmission electron microscopy. These results show that, in this experimental situation, high temperature alone is not sufficient to cause the {alpha}-{beta} transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2012

FABRICATION OF URANIUM OXYCARBIDE KERNELS AND COMPACTS FOR HTR FUEL

As part of the program to demonstrate tristructural isotropic (TRISO)-coated fuel for the Next Generation Nuclear Plant (NGNP), Advanced Gas Reactor (AGR) fuel is being irradiation tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). This testing has led to improved kernel fabrication techniques, the formation of TRISO fuel particles, and upgrades to the overcoating, compaction, and heat treatment processes. Combined, these improvements provide a fuel manufacturing process that meets the stringent requirements associated with testing in the AGR experimentation program. Researchers at Idaho National Laboratory (INL) are working in conjunction with a team from Babcock and Wilcox (B&W) and Oak Ridge National Laboratory (ORNL) to (a) improve the quality of uranium oxycarbide (UCO) fuel kernels, (b) deposit TRISO layers to produce a fuel that meets or exceeds the standard developed by German researches in the 1980s, and (c) develop a process to overcoat TRISO particles with the same matrix material, but applies it with water using equipment previously and successfully employed in the pharmaceutical industry. A primary goal of this work is to simplify the process, making it more robust and repeatable while relying less on operator technique than prior overcoating efforts. A secondary goal is to improve first-pass yields to greater than 95% through the use of established technology and equipment. In the first test, called “AGR-1,” graphite compacts containing approximately 300,000 coated particles were irradiated from December 2006 to November 2009. The AGR-1 fuel was designed to closely replicate many of the properties of German TRISO-coated particles, thought to be important for good fuel performance. No release of gaseous fission product, indicative of particle coating failure, was detected in the nearly 3-year irradiation to a peak burn up of 19.6% at a time-average temperature of 1038–1121°C. Before fabricating AGR-2 fuel, each fabrication process was improved and changed. Changes to the kernel fabrication process included replacing the carbon black powder feed with a surface-modified carbon slurry and shortening the sintering schedule. AGR-2 TRISO particles were produced in a 6-inch diameter coater using a charge size about 21-times that of the 2-inch diameter coater used to coat AGR-1 particles. The compacting process was changed to increase matrix density and throughput by increasing the temperature and pressure of pressing and using a different type of press. AGR-2 fuel began irradiation in the ATR in late spring 2010.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Composite binder, processing, and particle size effects on mechanical properties of non-hazardous high explosive surrogates

Plastic-bonded explosives (PBX) are polymer matrix composites that are highly loaded with micron-scale explosive crystals. The thermal and mechanical properties of these materials must be well-understood so that appropriate engineering models can be developed, but testing such properties under many scenarios can be hazardous and expensive. A non-hazardous PBX surrogate (“mock”) may be used in place of a PBX in many experiments if the thermomechanical properties are well-matched. Our previous research has shown that 5-iodo-2'-deoxyuridine (IDOX) is a promising crystalline filler material for the explosive cyclotetramethylene-tetranitramine (HMX). In this study, we investigate how the binder composition, variations in the IDOX particle size distribution, and pressing temperature affect the compressive strength and elastic modulus. We observe that while the binder system used in the composite dominates the mechanical response, the particle size distribution and pressing conditions do have a measurable effect on the material compliance and strength.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗