Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Visualization, understanding, and mitigation of process-induced-membrane irregularities in gas diffusion electrode-based polymer electrolyte membrane fuel cells

Polymer electrolyte membrane fuel cells (PEMFC) show substantial promise for their application in electric vehicles. For large-scale manufacturing of PEMFCs, roll-to-roll coated gas-diffusion-electrodes (GDE) offer certain advantages over other production pathways. Procedures including hot pressing and coating an ionomer overlayer may be necessary for this manufacturing pathway to enable a suitable catalyst layer/membrane interface. The same procedures may potentially introduce membrane irregularities, especially when thin membranes are used. Limited understanding exists regarding if and to what extent such irregularities impact PEMFC performance and lifetime, and therefore be considered defects. In this study, NREL's customized fuel cell hardware that enables quasi in-situ infrared (IR) thermography studies was utilized to visualize spatial hydrogen crossover and identify membrane irregularities that originated from the GDE-based MEA fabrication process. The structure of these membrane irregularities was investigated by scanning electron microscopy (SEM) and its impact on initial H2/air performance was determined. Accelerated stress testing (AST) revealed that these irregularities develop into failure point locations. These results were validated across many MEAs with identified process-induced membrane irregularities. By selecting specific gas diffusion media properties and by fine tuning the MEA hot pressing parameters, the formation of such membrane irregularities was mitigated.

08 HYDROGEN↗

Enhanced diffusion bonding of alloy 617 using electric field-assisted sintering

The development of compact heat exchangers (CHXs) has gained increasing interest in many industries owing to their high thermal efficiency and reduced size. Diffusion bonding (DB) is an advantageous technique for fabricating CHXs. Alloy 617 is a candidate for manufacturing CHXs for high-temperature advanced nuclear reactors due to its elevated-temperature properties. Previous endeavors in DB of Alloy 617 were conducted by hot pressing (HP), which reported precipitates at the diffusion-bond interface, limited grain boundary (GB) migration, and significantly reduced high-temperature mechanical properties. To overcome these challenges, this study investigated DB of Alloy 617 using electric field-assisted sintering (EFAS). Stacks composed of three sheets were bonded with EFAS using different temperatures, pressures, and hold times. DB using HP as the zero-current analog of EFAS was also performed for comparison. The result shows that Cr- and Mo-rich precipitates were formed at the interface of the hot-pressed samples. The electric current and temperature in EFAS play a significant role in precipitation and GB migration. The electric current coupled with correct temperatures can effectively prevent precipitate formation at the interface and achieve excellent GB migration. Nanoscale Al-rich oxide was formed at the interface of the samples made by both HP and EFAS, but grain boundaries can ignore the nanoscale Al-oxide and migrate across the interface. The temperature, pressure, and hold time also affected diffusion. The temperature is a prerequisite for a successful GB migration, and GB migration can be enhanced by increasing pressure and hold time.

36 MATERIALS SCIENCE↗

Fabrication and Characterization of Fully Ceramic Microencapsulated Fuels

The current generation of fully ceramic microencapsulated fuels, consisting of Tristructural Isotropic fuel particles embedded in a silicon carbide matrix, is fabricated by hot pressing. Matrix powder feedstock is comprised of alumina - yttria additives thoroughly mixed with silicon carbide nanopowder using polyethyleneimine as a dispersing agent. Fuel compacts are fabricated by hot pressing the powder - fuel particle mixture at a temperature of 1800-1900 C using compaction pressures of 10-20 MPa. Detailed microstructural characterization of the final fuel compacts shows that oxide additives are limited in extent and are distributed uniformly at silicon carbide grain boundaries, at triple joints between silicon carbide grains, and at the fuel particle-matrix interface.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fabrication and Preliminary Evaluation of Metal Matrix Microencapsulated Fuels

The metal matrix microencapsulated (M3) fuel concept for light water reactors (LWRs), consisting of coated fuel particles dispersed in a zirconium metal matrix, is introduced. Fabrication of M3 fuels by hot pressing, hot isostatic pressing, or extrusion methodologies has been demonstrated over the temperature range 800-1050 C. Various types of coated fuel particles with outermost layers of pyrocarbon, SiC, ZrC, and TiN have been incorporated into the zirconium metal matrix. Mechanical particle-particle and chemical particle-matrix interactions have been observed during the preliminary characterization of as-fabricated M3 specimens. Irradiation of three M3 rodlets with surrogate coated fuel particles was carried out at mean rod temperature of 400 C to 4.6 dpa in the zirconium metal matrix. Due to absence of texture in the metal matrix no irradiation growth strain (<0.09%) was detected during the post-irradiation examination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Glass-bonded ceramic waste forms for immobilization of radioiodine from caustic scrubber wastes

Glass-bonded sodalite composite waste forms have been developed for the immobilization of liquid radioactive wastes resulting from off-gas treatment during aqueous reprocessing of used nuclear fuel, with a particular focus on 129I. The proposed composite waste form is comprised of aluminosilicate ceramic phases containing volatile radionuclides bonded with a glassy matrix. In this work, a suite of ten candidate low-temperature glass binders (ZnO-Bi2O3-based glasses and a Na2O-B2O3-SiO2 glass) were examined. Six glasses were mixed with caustic scrubber waste simulant previously converted into a sodalite-rich material (to provide glass fractions of 10 and 20 wt.%), uniaxially pressed into pellets, and sintered at 350 °C or 550 °C for 8 h in air. Iodine retention after heat treatment was assessed by neutron activation analysis, showing retention of 67-100 % of expected iodine. The aqueous durabilities of the resulting materials were then determined, following the ASTM C1308 standard test, showing iodine releases of 1 to 23 g m-2 after 4 d. The cumulative iodine release for the best performing system (a zinc-bismuth-borate glass binder) was <1 g m-2, and its iodine retention from processing was 67 %. The iodine releases compared favorably with other waste forms. In parallel, this best-performing composition was also consolidated via hot isostatic pressing (HIP) in a stainless-steel canister at 550 °C for 2 h under 100 MPa pressure. The HIPed sample was produced at the ~20 g scale and showed improved densification and minimal reaction with the canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improvement of the thermoelectric properties of [Bi{sub 1.68}Ca{sub 2}O{sub 4-{delta}}]{sup RS}[CoO{sub 2}]{sub 1.69} cobaltite by chimie douce methods

[Bi{sub 1.68}Ca{sub 2}O{sub 4-{delta}}]{sup RS}[CoO{sub 2}]{sub 1.69} has been obtained by different chimie douce methods and uniaxially or isostatically pressed. The influence of these parameters on the thermoelectric properties has been investigated. Contrary to the Seebeck coefficient, which remains unchanged, the electrical conductivity is greatly modified. In particular, spray-drying synthesis followed by uniaxial pressing results in an electrical conductivity two times larger than in the case of conventional solid state synthesis. Our results suggest that a narrow particle size distribution is beneficial to the thermoelectric properties of the layered compounds. The spray-drying technique seems to be promising to improve the electrical conductivity of layered materials. Moreover, this method presents other advantages (homogeneous samples and less energetic processing) which could be interesting to the future manufacturing of thermoelectric devices. - Graphical abstract: Small particles and narrow size distribution is obtained for spray-drying [Bi{sub 1.68}Ca{sub 2}O{sub 4}]{sup RS}[CoO{sub 2}]{sub 1.69} cobaltate. The power factor is boosted up two times compared with the conventional solid state method.

36 MATERIALS SCIENCE↗

Microstructure and thermal conductivity of surfactant-free NiO nanostructures

High purity, nanometer sized surfactant-free nickel oxide (NiO) particles were produced in gram scale using a solution combustion method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), gas pycnometry and gas adsorption analysis (BET). The average particle size of the as-synthesized NiO increases significantly with the preheating temperature of the furnace, while the specific surface area decreases. A BET specific surface area of {approx}100 m{sup 2}/g was obtained for NiO nanoparticles with size as small as 3 nm synthesized at 300 Degree-Sign C. The thermal conductivity ({kappa}) of pressed pellets of the synthesized NiO nanoparticles obtained using spark plasma sintering (SPS) and uniaxial hot pressing is drastically decreased ({approx}60%) compared to that of NiO single crystal. This strong reduction in {kappa} with particle size suggests the suitability of the synthesized surfactant-free NiO nanoparticles for use as nanoinclusions when designing high performance materials for waste heat recovery. - Graphical abstract: Highly efficient phonon scattering by surfactant-free NiO nanostructures obtained by solution combustion of a mixture of nickel (II) nitrate hexahydrate (oxidizer) and urea (fuel) at various temperatures. Highlights: Black-Right-Pointing-Pointer Fast synthesis of surfactant-free NiO nanoparticles with controllable size. Black-Right-Pointing-Pointer High specific surface area for NiO nanoparticles with size range from 3 to 7 nm. Black-Right-Pointing-Pointer Strong reduction of the thermal conductivity with decreasing particle size. Black-Right-Pointing-Pointer NiO as nanoinclusions in high performance materials for energy conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Correlation between processing conditions, microstructure and charge transport in half-Heusler alloys

Five bulk samples of n-type Zr₀.₂₅Hf₀.₇₅NiSn₀.₉₇₅Sb₀.₀₂₅ half-Heusler (HH) alloy were fabricated by reacting elemental powders via (1) high temperature solid state (SS) reaction and (2) mechanical alloying (MA), followed by densification using spark plasma sintering (SPS) and/or hot pressing (HP). A portion of the sample obtained by SS reaction was mechanically alloyed before consolidation by hot pressing (SS–MA–HP). X-ray powder diffraction and transmission electron microscopy studies revealed that all SS specimen (SS–SPS, SS–HP, SS–MA–HP) are single phase HH alloys, whereas the MA sample (MA–SPS) contains metallic nanoprecipitates. Electronic and thermal transport measurements showed that the embedded nanoprecipitates induce a drastic increase in the carrier concentration (n), a large decrease in the Seebeck coefficient (S) and a marginal decrease in the lattice thermal conductivity (κ l ) of the MA–SPS sample leading to lower ZT values when compared to the SS–HP samples. Constant values of S are observed for the SS series regardless of the processing method. However, a strong dependence of the carrier mobility (μ), electrical conductivity (σ) and κ l on the processing and consolidation method is observed. For instance, mechanical alloying introduces additional structural defects which enhance electron and phonon scattering leading to moderately low values of μ and large reduction in κ l . This results in a net 20% enhancement in the figure of merit (ZT=0.6 at 775 K). HH specimen of the same nominal composition with higher ZT is anticipated from a combination of SS reaction, MA and SPS (SS–MA–SPS). - Graphical abstract: In half-Heusler alloys, thermopower values are insensitive to processing method, whereas carrier mobility (μ), electrical conductivity (σ), and κ l strongly dependent on the microstructure which in turn is altered by the synthesis, processing and consolidation method. Highlights: • Phase composition of HH alloy strongly depends on the synthesis technique. • Mechanical alloying of elements yields bulk HH alloy with metallic impurity phases. • Thermopower, carrier density, and effective mass of HHs are insensitive to processing conditions. • Mechanical alloying decreases the carrier mobility and lattice thermal conductivity of bulk HH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Variations of thermoelectric properties of Mg{sub 2.2}Si{sub 1−y}Sn{sub y−0.013}Sb{sub 0.013} materials with different Si/Sn ratios

Mg{sub 2}Si–Mg{sub 2}Sn solid solutions are a promising class of thermoelectric materials. Mg{sub 2.2}Si{sub 1−y}Sn{sub y−0.013}Sb{sub 0.013} compounds with different Si/Sn ratios were prepared by B{sub 2}O{sub 3} “flux” method followed by hot-pressing. The effect of Si/Sn ratio on the thermoelectric properties of the Mg{sub 2}Si–Mg{sub 2}Sn solid solutions at a fixed Sb doping level were measured in the temperature range 300–760 K. With the increase of Sn content (0.3≤y≤0.7), power factors are improved and lattice thermal conductivity decreased. Band convergence induced by Si/Sn ratio leads to enhanced effective mass and the materials parameter β which qualifies a kind of thermoelectric material is improved evidently. A maximum ZT of ∼1.1 at ∼760 K was achieved for the Mg{sub 2.2}Si{sub 0.3}Sn{sub 0.7–0.013}Sb{sub 0.013} sample arising from a high power factor of ∼4×10{sup -3} W m{sup −1} K{sup −2} and a low lattice thermal conductivity of ∼1.6 W m{sup −1} K{sup −1} at ∼760 K. - Graphical abstract: (a)Temperature dependence of power factor of Mg{sub 2.2}Si{sub 1−y}Sn{sub y−0.13}Sb{sub 0.013} samples. (b)Temperature dependence of lattice thermal conductivity of Mg{sub 2.2}Si{sub 1−y}Sn{sub y−0.13}Sb{sub 0.013} samples. (c)Temperature dependence of dimensionless figure of merit ZT of Mg{sub 2.2}Si{sub 1−y}Sn{sub y−0.13}Sb{sub 0.013} samples. - Highlights: • Mg{sub 2.2}Si{sub 1−y}Sn{sub y−0.013}Sb{sub 0.013} was prepared by B{sub 2}O{sub 3} ''flux'' method followed by hot-pressing. • Band convergence leads to enhanced m{sup ⁎} and improved materials parameter β. • ZT{sub max} of ∼1.1 at ∼760 K was achieved for the Mg{sub 2.2}Si{sub 0.3}Sn{sub 0.7−0.013}Sb{sub 0.013} sample.

36 MATERIALS SCIENCE↗

Effects of additions of carbon nanotubes on the thermoelectric properties of Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}

To prepare Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}, the starting materials were loaded in the stoichiometric ratio into silica tubes and then heated at 1000 K. The reaction products were mixed and divided into four equal parts. The first sample was used as a reference sample called bulk. For the remaining samples, 1%, 2% and 3% by mass of MWCNT (multi-wall carbon nanotubes) were added by ball-milling. These materials were then subjected to consolidation by hot-pressing at 850 K and 56 MPa. Their transport properties were determined and compared to study the influence of MWCNT on the transport properties of Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}. Scanning and transmission electron microscopy were used to study the microstructural and nanostructural features of the samples, and Raman characterization was performed to look for changes induced by ball-milling and hot-pressing of the nanotubes. Mainly due to a largely reduced thermal conductivity by 40% and a slightly reduced power factor, the figure-of-merit was improved by 25% after addition of 3 mass% of MWCNT. - Graphical abstract: Figure-of-merit of various Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6}/CNT composites. - Highlights: • Various composites of Ni{sub 0.05}Mo{sub 3}Sb{sub 5.4}Te{sub 1.6} with carbon nanotubes were synthesized and characterized. • In each case, the thermoelectric figure-of-merit increases rapidly with increasing temperature. • With increasing amount of carbon nanotubes, the thermal conductivity decreases more than the electrical conductivity. • The composite with 3% carbon nanotubes performs better than the bulk material by 25%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure characterization of LAE442 magnesium alloy processed by extrusion and ECAP

The magnesium alloy LAE442 was processed by extrusion and equal channel angular pressing (ECAP) to achieve ultrafine grained microstructure. Detailed characterization of the microstructure was performed by scanning electron microscope, electron back scattered diffraction (EBSD) and transmission electron microscope. The initial, as-cast, microstructure consisted of large grains of ~ 1 mm. The grain refinement due to the processing by severe plastic deformation led to a decrease of the average grain size to ~ 1.7 μm after the final step of ECAP. A detailed characterization of secondary phases showed the precipitation of Al{sub 11}RE{sub 3}, Al{sub 2}Ca and Al{sub 10}RE{sub 2}Mn{sub 7} intermetallic phases. X-ray diffraction measurements proved that Li is dissolved within the magnesium matrix in the as-cast condition. Newly formed Al{sub 3}Li phase was observed after ECAP. The texture formation due to the extrusion and ECAP was different from that in the other magnesium alloys due to the activation of non-basal slip systems as a result of the decrease of the c/a ratio. - Highlights: • Combined extrusion and equal channel angular pressing results in significant grain refinement by factor 1000 approximately. • Al{sub 11}RE{sub 3}, Al{sub 2}Ca and Al{sub 10}RE{sub 2}Mn{sub 7} secondary phases are present in the as-cast material while Li was dissolved in the Mg matrix. • Extrusion and ECAP have no effect on the composition of the secondary phases but they influence strongly their distribution. • Texture evolution is affected by decrease of c/a ratio due to the presence of Li and resulting activation of non-basal slip.

36 MATERIALS SCIENCE↗

Comparative investigation on microstructures and mechanical properties of (TiB + TiC)/Ti-6Al-4V composites from Ti-B4C-C and Ti-TiB2-TiC systems

Highlights: • The (TiB{sub w}+TiC{sub p})/Ti-6Al-4V composites were fabricated from Ti-B{sub 4}C-C and Ti-TiB{sub 2}-TiC systems by reactive hot-pressed sintering. • Microstructures and mechanical properties of the two kinds of composites were comparatively investigated. • The composites from Ti-TiB{sub 2}-TiC system possess higher elastic modulus and Vickers hardness than those from Ti-B{sub 4}C-C system. • The composites from Ti-TiB{sub 2}-TiC system have higher bending strength than the other system while employing same conditions. • The composites from Ti-B{sub 4}C-C system present better abrasion resistance than those from Ti-TiB{sub 2}-TiC system. - Abstract: Two percentages of TiB + TiC reinforced Ti-6Al-4V composites from Ti-B{sub 4}C-C and Ti-TiB{sub 2}-TiC systems were fabricated by reactive hot-pressed sintering. Their microstructures and mechanical properties involving elastic modulus, Vickers hardness, bending strength and wear property were investigated comparatively. The experimental results show that needle-like TiB whiskers and near-equiaxed TiC particles are evenly distributed in the Ti-6Al-4V matrix. The mechanical properties of the (TiB + TiC)/Ti-6Al-4V composites are closely related with the nominal composition and synthesis system of TiB + TiC reinforcement and the microstructures of composites. With increasing the nominal volume fraction of reinforcement, both elastic modulus and Vickers hardness increase more or less and the bending strength decreases in varying degrees. A certain increase of pores in the composites with the sintering temperature increasing to 1300 °C can markedly affect the bending strength. Moreover, no matter what the sintering temperature and nominal volume fraction of reinforcement, the elastic modulus and Vickers hardness of composites from the Ti-TiB{sub 2}-TiC system are higher than those from the Ti-B{sub 4}C-C system. Similarly, the composites from the Ti-B{sub 4}C-C system present better abrasion resistance than those from the Ti-TiB{sub 2}-TiC system due to the difference of interfacial bonding between the TiC particles and Ti-6Al-4V matrix in the two kinds of composites.

36 MATERIALS SCIENCE↗

A study of microstructure of Fe-Cu-Ni-Sn and Fe-Cu-Ni-Sn-VN metal matrix for diamond containing composites

Highlights: • A nanocrystalline sample of coarse-grained powders of iron, copper, nickel, tin was obtained. • The structure of the sample consists of a supersaturated solid solution of nitrogen and vanadium in α-Fe. • Grain refinement occurs as a result of the decomposition of supersaturated solid solution of nitrogen and vanadium in α-Fe. To obtain bulk of 51Fe–32Cu–9Ni–8Sn and 49.47Fe–31.04Cu–8.73Ni–7.76Sn–3VN nanocomposites, a pressing method at room temperature and subsequent hot pressing in a vacuum was used. The microstructure of the sintered composites by X-ray diffraction and transmission electron microscopy was investigated. It is shown that in the 49.47Fe–31.04Cu–8.73Ni–7.76Sn–3VN composite there was a dissolution of vanadium nitride in γ‑iron and formation of a supersaturated solid solution of nitrogen and vanadium in the α‑iron. As a result, there was a substantial grinding of ferrite grains (from 5 to 50 μm to 20–400 nm) as compared to a sample without vanadium nitride (from 5 to 50 μm to 400–800 nm). Nanocomposites are considered as promising materials to create a new generation of diamond containing composites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The effect of Gd3+ ions on fabrication and luminescence properties of Nd3+-doped (Ca1-xGdx)F2+x transparent ceramics

Highlights: • Nd:(Ca{sub 1-x}Gd{sub x})F{sub 2+x} transparent ceramics were fabricated by hot-pressing method. • Concentration effect of Gd{sup 3+} ion on the optical properties are discussed. • The emission properties have been greatly enhanced by codoping with Gd{sup 3+}ions. • The fluorescence parameters were compared to other Nd{sup 3+}-doped optical materials. - Abstract: Nd:(Ca{sub 1-x}Gd{sub x})F{sub 2+x} (x = 0.01–0.1) transparent ceramics were fabricated by hot-pressing the co-precipitated synthetic nanopowders in vacuum. The as-fabricated Nd:(Ca{sub 1-x}Gd{sub x})F{sub 2+x} transparent ceramics exhibit nearly pore-free and uniform microstructure, the in-line transmittance of all samples is beyond 86% at 1064 nm. The effect of Gd{sup 3+} ions on the transparency and grain size of Nd:(Ca{sub 1-x}Gd{sub x})F{sub 2+x} transparent ceramics has been demonstrated. The dependence of emission intensity and lifetime on Gd{sup 3+} concentration for Nd:(Ca{sub 1-x}Gd{sub x})F{sub 2+x} transparent ceramics is investigated and discussed. The introducing of Gd{sup 3+} is found to increase emission intensity and lifetime dramatically. The fitting results of fluorescence decay curves show the lifetime of 1 at.% Nd:(Ca{sub 0.9}Gd{sub 0.1})F{sub 2.1} transparent ceramic is to be 373.80 μs which is greatly larger than that of 1 at.% Nd:CaF{sub 2} transparent ceramic. The spectroscopic parameters of Nd:(Ca{sub 1-x}Gd{sub x})F{sub 2+x} transparent ceramics and other Nd{sup 3+}-doped optical materials have been compared and discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Suppression of grain growth by additive in nanostructured p-type bismuth antimony tellurides

Grain growth is a major issue in the preparation of nanostructured bismuth-antimony-tellurides during hot pressing the nanopowders into dense bulk samples. To prevent grain agglomeration during ball milling and growth during hot pressing, organic agent (Oleic Acid, OA) as additive was added here into the materials at the beginning of the ball milling process. With different concentrations of OA (0.5, 1.0, 1.5, 2.0, and 2.5 wt%), grains with different sizes are obtained. Structural analysis clearly shows that it is the particle size of the nanopowders that determines the final grain size in the densely compacted bulk samples. A combination of small grains ~200–500 nm and nanopores leads to effective phonon scattering, which results in the decrease of lattice thermal conductivity, and ZT of ~1.3 at 373 K for the sample with 2.0 wt% OA.

36 MATERIALS SCIENCE↗

Cold compaction study of Armstrong Process Ti-6Al-4V powders

This work investigates the cold compaction behavior of Ti-6Al-4V powders produced by Armstrong Process . As-received as well as milled powders were characterized and these powders were uniaxially die-pressed at designated pressures up to 690 MPa to form disk samples with different aspect ratios. Samples with high aspect ratio exhibited non-uniform density along the pressing axis and the density distribution is in consistent with the result predicted by finite element analysis. The linear regression analysis on the experimental density data can be used to predict density of compacts with different aspect ratios. In the studied pressure range, an empirical powder compaction equation represents the green density pressure relationship very well for both the as-received and 1-hr milled Armstrong Ti-6Al-4V powders.

99 GENERAL AND MISCELLANEOUS↗

Rapid Microwave Preparation of Thermoelectric TiNiSn and TiCoSb Half-Heusler Compounds

The 18-electron ternary intermetallic systems TiNiSn and TiCoSb are promising for applications as high-temperature thermoelectrics and comprise earth-abundant, and relatively nontoxic elements. Heusler and half-Heusler compounds are usually prepared by conventional solid state methods involving arc-melting and annealing at high temperatures for an extended period of time. Here, we report an energy-saving preparation route using a domestic microwave oven, reducing the reaction time significantly from more than a week to one minute. A microwave susceptor material rapidly heats the elemental starting materials inside an evacuated quartz tube resulting in near single phase compounds. The initial preparation is followed by a densification step involving hot-pressing, which reduces the amount of secondary phases, as verified by synchrotron X-ray diffraction, leading to the desired half-Heusler compounds, demonstrating that hot-pressing should be treated as part of the preparative process. For TiNiSn, high thermoelectric power factors of 2 mW/mK{sup 2} at temperatures in the 700 to 800 K range, and zT values of around 0.4 are found, with the microwave-prepared sample displaying somewhat superior properties to conventionally prepared half-Heuslers due to lower thermal conductivity. The TiCoSb sample shows a lower thermoelectric figure of merit when prepared using microwave methods because of a metallic second phase.

36 MATERIALS SCIENCE↗

High strength bulk Fe-Co alloys produced by powder metallurgy

Fe-Co alloys are extensively used in lamination form, but there are certain power generation applications that require Fe-Co rotors in bulk form. Experiencing only a dc magnetic field, these rotors can be as large as 0.5 m in diameter, depending on the size of the generator. The forging of such large pieces of Fe-Co has proven to be difficult. The present study investigates powder metallurgy processing of a gas atomized FeCoNbV alloy through hot isostatic pressing (HIP) for manufacturing large size rotors with improved mechanical strength. Gas atomized FeCoNbV alloy powders with and without ball milling were hot isostatic pressed at temperatures between 675 and 850 deg. C at a fixed pressure of 193 MPa for up to 6 h. Ball milling prior to HIP improved the yield strength. A further improvement in yield strength and in ductility was obtained after a disordering heat treatment at 730 deg. C followed by a rapid quench to room temperature. The optimum HIP and annealing conditions resulted in samples with yield strengths of 870 MPa. The compacts exhibited average coercivity values of 6.4 Oe and maximum permeability values of 1100.

36 MATERIALS SCIENCE↗