Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Plastic Waste Product Captures Carbon Dioxide in Nanometer Pores

We discuss, plastic waste (PW) and increasing atmospheric carbon dioxide (CO 2 ) levels are among the top environmental concerns presently facing humankind. With an ambitious 2050 zero-CO 2 emissions goal, there is a demand for economical CO 2 capture routes. Here we show that the thermal treatment of PW in the presence of potassium acetate yields an effective carbon sorbent with pores width of 0.7–1.4 nm for CO 2 capture. The PW to carbon sorbent process works with single or mixed streams of polyolefin plastics. The CO 2 capacity of the sorbent at 25 °C is 17.0 ± 1.1 wt % (3.80 ± 0.25 mmol g –1 ) at 1 bar and 5.0 ± 0.6 wt % (1.13 ± 0.13 mmol g –1 ) at 0.15 bar, and it regenerates upon reaching 75 ± 5 °C. The CO 2 capture cost from flue gas via this technology is estimated to be <$21 ton –1 CO 2 , much lower than competing CO 2 capture technologies. Hence, this PW-derived carbon material should find utility in the capture of CO 2 from point sources of high CO 2 emissions while providing a use for otherwise deleterious PW.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

Delamination of Multilayer Plastic Films to Recover Polyethylene with Favorable Mechanical Properties

Multilayer plastic films play a critical role in packaging, with each polymer layer contributing specific properties to the multilayer film. Multilayer plastic films are not currently recyclable due to the bound polymers. With multilayer film production of about 20 million metric tons in 2024 and rising, endof- life treatment becomes pressing. This work presents a scalable solvent-based delamination recycling process that is applied to commercial postindustrial multimaterial films to unbind the materials within a multilayer film by dissolving only the adhesive layer and recover polyethylene (PE) as an intact solid film. Solventbased delamination is a simple process that allows the complete recovery of materials and solvents used in the process. The delaminating solvent, 88% formic acid in water, induces delamination of PE/PEI/PET and PE/PU/PET films at 70 °C in under an hour. Recovered PE has no contamination detected by Fourier transform infrared spectroscopy and mechanical properties on par with those of virgin resin. The recovery of high-quality solid PE film fit for reprocessing, at low operating temperatures and with closed-loop solvent reuse, promotes delamination as a low energy consumption and environmentally friendly recycling process. PE recovered from delamination can be reused in equivalent products, promoting circularity of multimaterial films.

chemical recycling↗
DOE OSTI2014

Various sizes of sliding event bursts in the plastic flow of metallic glasses based on a spatiotemporal dynamic model

This paper presents a spatiotemporal dynamic model based on the interaction between multiple shear bands in the plastic flow of metallic glasses during compressive deformation. Various sizes of sliding events burst in the plastic deformation as the generation of different scales of shear branches occurred; microscopic creep events and delocalized sliding events were analyzed based on the established model. This paper discusses the spatially uniform solutions and traveling wave solution. The phase space of the spatially uniform system applied in this study reflected the chaotic state of the system at a lower strain rate. Moreover, numerical simulation showed that the microscopic creep events were manifested at a lower strain rate, whereas the delocalized sliding events were manifested at a higher strain rate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Defect induced plasticity and failure mechanism of boron nitride nanotubes under tension

The effects of Stone-Wales (SW) and vacancy defects on the failure behavior of boron nitride nanotubes (BNNTs) under tension are investigated using molecular dynamics simulations. The Tersoff-Brenner potential is used to model the atomic interaction and the temperature is maintained close to 300 K. The effect of a SW defect is studied by determining the failure strength and failure mechanism of nanotubes with different radii. In the case of a vacancy defect, the effect of an N-vacancy and a B-vacancy is studied separately. Nanotubes with different chiralities but similar diameter is considered first to evaluate the chirality dependence. The variation of failure strength with the radius is then studied by considering nanotubes of different diameters but same chirality. It is observed that the armchair BNNTs are extremely sensitive to defects, whereas the zigzag configurations are the least sensitive. In the case of pristine BNNTs, both armchair and zigzag nanotubes undergo brittle failure, whereas in the case of defective BNNTs, only the zigzag ones undergo brittle failure. An interesting defect induced plastic behavior is observed in defective armchair BNNTs. For this nanotube, the presence of a defect triggers mechanical relaxation by bond breaking along the closest zigzag helical path, with the defect as the nucleus. This mechanism results in a plastic failure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2015

Plastic scintillators modifications for a selective radiation detection

Recent developments of plastic scintillators are reviewed, from January 2000 to June 2015. All examples are distributed into the main application, i.e. how the plastic scintillator was modified to enhance the detection towards a given radiation particle. The main characteristics of these newly created scintillators and their detection properties are given. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Mixed Plastics Waste Valorization through Tandem Chemical Oxidation and Biological Funneling

Mixed plastics waste represents an abundant and largely untapped feedstock for the production of valuable products. The chemical diversity and complexity of these materials, however, present major barriers to realizing this opportunity. In this work, we show that metal-catalyzed autoxidation depolymerizes comingled polymers into a mixture of oxygenated small molecules that are advantaged substrates for biological conversion. We engineer a robust soil bacterium, Pseudomonas putida, to funnel these oxygenated compounds into a single exemplary chemical product, either ..beta..-ketoadipate or polyhydroxyalkanoates. This hybrid process establishes a strategy for the selective conversion of mixed plastics waste into useful chemical products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Investigating the Difference in Mechanical Stability of Retained Austenite in Bainitic and Martensitic High-Carbon Bearing Steels using in situ Neutron Diffraction and Crystal Plasticity Modeling

In situ neutron diffraction of the uniaxial tension test was used to study the effect of the surrounding matrix microstructure on the mechanical stability of retained austenite in high-carbon bearing steels. Comparing the samples with bainitic microstructures to those with martensitic ones, it was found that the retained austenite in a bainitic matrix starts transforming into martensite at a lower strain compared to that within a martensitic matrix. On the other hand, the rate of transformation of the austenite was found to be higher within a martensitic microstructure. Crystal plasticity modeling was used to analyze the transformation phenomenon in these two microstructures and determine the effect of the surrounding microstructure on elastic, plastic, and transformation components of the strain. The results showed that the predominant difference in the deformation accumulated was from the transformation strain and the critical transformation driving force within the two microstructures. The retained austenite was more stable for identical loading conditions in case of martensitic matrix compared to the bainitic one. It was also observed that the initial volume fraction of retained austenite within the bainitic matrix would alter the onset of transformation to martensite, but not the rate of transformation.

bainite↗
NASA NTRS1948

A unified theory of plastic buckling of columns and plates

On the basis of modern plasticity considerations, a unified theory of plastic buckling applicable to both columns and plates has been developed. For uniform compression, the theory shows that long columns which bend without appreciable twisting require the tangent modulus and that long flanges which twist without appreciable bending require the secant modulus. Structures that both bend and twist when they buckle require a modulus which is a combination of the secant modulus and the tangent modulus. (author)

PLATES - PLASTICITY↗
DOE OSTI2011

PLASTIC BEHAVIOR OF POLYCRYSTALLINE TANTALUM IN THE 5 x 10^7/s REGIME

The goal of this experiment is to investigate the plastic response of Tantalum to dynamic loading at high strain rates. The samples used were derived from high purity rolled plate, polished down to thicknesses in the range 25-100 {micro}m. Dynamic loading was applied by direct laser ablation of the sample, with pulses up to 10 ns long, at the Jupiter Laser Facility. The elastic-plastic wave structure was measured using two line VISAR systems of different sensitivity, and strain rates were inferred from the rise time of the waves. The elastic wave amplitudes indicated flow stresses between 2 and 3 GPa, depending on the sample thickness. Samples were recovered for post-shot metallographic analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2019

NREL Develops Method to Upcycle Plastic Bottles and Protect Environment

NREL researchers have discovered a method of plastics upcycling—transforming discarded products into new, high-value materials of better quality and environmental value—that could economically incentivize the recycling of waste plastics and help solve one of the world’s most looming pollution problems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2018

Efficiency Calculation for an In-situ Beta Nuclide Monitoring System Based on a Plastic Scintillator - 18193

A plastic scintillator performance for an in-situ measurement system was analyzed using both simulation and experimental methods. The measurement results of four major pure beta-emitting radionuclides - namely H-3. C-14, P-32 and Sr-90/Y-90 - were compared with those from a Monte Carlo N-particle (MCNP) code simulation. Good agreement between the simulation and experimental results was observed for P-32 and Sr-90/Y-90. However, due to the short range of their beta particles in water, the efficiency for both H-3 and C-14 was rather low, and these radionuclides could not be detected. The optimal thickness for the plastic scintillator was identified, as was its suggested diameter. The effect of water depth on system performance was also considered. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2017

Linking plant functional trait plasticity and the large increase in forest water use efficiency

Elevated atmospheric CO 2 concentrations are anticipated to enhance photosynthesis and reduce stomatal conductance, thus increasing plant water use efficiency. A recent study based on eddy covariance flux observations from Northern Hemisphere forests showed a large increase in inherent water use efficiency (IWUE). Here we used an updated version of the same data set and robust uncertainty quantification to revisit these contemporary IWUE trends. We tested the hypothesis that the observed IWUE increase could be attributed to interannual trends in plant functional traits, potentially triggered by environmental change. We postulate that IWUE increased by ~1.3% yr -1 , which is less than previously reported but still larger than theoretical expectations. Numerical simulations with the Tethys-Chloris ecosystem model using temporally static plant functional traits cannot explain this increase. Simulations with plant functional trait plasticity, i.e., temporal changes in model parameters such as specific leaf area and maximum Rubisco capacity, match the observed trends in IWUE. Our results show that trends in plant functional traits, equal to 1.0% yr -1 , can explain the observed IWUE trends. Thus, at decadal or longer time scales, trait plasticity could potentially influence forest water, carbon, and energy fluxes with profound implications for both the monitoring of temporal changes in plant functional traits and their representation in Earth system models.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Upcycling of Waste Plastics into Carboxylic Acids for Biodegradable Surfactants

This work outlines a process for producing high‐purity (>95%) carboxylate surfactants from post‐consumer recycled high‐density polyethylene (PCR‐HDPE). The approach involves the thermal depolymerization of PCR‐HDPE via pyrolysis, followed by fractional distillation to isolate C9–C14 olefins. These olefins undergo hydroformylation using cobalt carbonyl catalysts to generate aldehydes, which are subsequently oxidized to carboxylic acids using Pinnick oxidation under mild aqueous‐phase conditions. Neutralization of the resulting carboxylic acids with sodium hydroxide produces plastic‐derived carboxylate surfactants (PDCs) in the form of sodium carboxylates. Subsequent purification steps ensure surfactant‐grade purity and enable accurate assessment of physicochemical properties. The resulting PDCs are evaluated for critical micelle concentration (CMC), foamability, surface tension reduction, and calcium ion tolerance, demonstrating competitive behavior with conventional anionic carboxylate surfactants. This route provides a sustainable alternative for surfactant production, reducing reliance on fossil‐derived feedstocks and valorizing plastic waste streams through chemical upcycling.

Biodegradable surfactants↗
DOE OSTI2026

Catalytic Autoxidation for Depolymerization of Multilayer Plastic Films

Recycling multilayer plastic films is challenged by a diversity of polymers, prompting development of new recycling methods. For the depolymerization of mixed polymers like those in multilayer films, metal-catalyzed autoxidation offers a versatile chemical recycling method to deconstruct multiple polymers to useful oxygenates. Here, we demonstrate that catalytic autoxidation is effective for depolymerizing multilayer films across diverse chemistries. We investigated conditions for a model polyethylene substrate using a Co, Mn, and Br cocatalyst system, achieving full carbon closure with oxygenated small molecules contributing up to 48 mol% carbon. Subsequently, we characterized product distributions for several common polymers used in multilayer films using high-resolution mass spectrometry (HRMS) and developed analytical methods to quantify the resulting complex product streams. Optimized conditions for polyethylene were applied to 11 multilayer plastic films containing 10 different polymers, including films with nonpolymeric potential disrupters like aluminum foil and titanium dioxide, showing that catalytic autoxidation is effective across a broad range of polymer types and is resistant to disrupters and additives. The generation of CO 2 in these reactions overall suggests that both reaction engineering and modifications to the reaction conditions will be required to achieve higher yields of soluble oxygenated products.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Utilization of Ultrasonication as a Method of Reducing Organic and Inorganic Contamination in Post‐Consumer Plastic Film Waste

Post-consumer plastic film waste often carries organic and inorganic contaminants that challenge recycling processes and affect the quality of recycled products. An effective contaminant removal procedure through washing such single-used plastic films (SUPFs) can address environmental and waste management concerns. This study compares the efficiency of different washing techniques in reducing SUPF contamination. To evaluate the efficacy of each washing technique, film samples collected from material recovery facilities are individually exposed to friction, ultrasonic-assisted, and a combination of both washes. Thermal analysis indicates that the polymers' melting temperature, crystallization temperature, and crystallinity remain unaffected by the washing methods, demonstrating method aptness. Confocal laser scanning microscope images show that washing results in a cleaner sample surface. 91% ash reduction during the combined wash treatment indicates a high method efficiency compared to the individual friction and ultrasonic wash procedures. This is further validated by reducing characteristic contaminant IR bands (3600–3000, 1750–1600, and 1100–1000 cm −1 ). Elements of concern such as Cd, Cr, Hg, and Pb in SUPFs after each washing technique applied conform with regulations (<100 ppm) for packaging products. This research shows the novel ultrasonic washing reduces more contamination than friction with shorter wash times and no surfactants.

42 ENGINEERING↗
DOE OSTI2016

A robust return-map algorithm for general multisurface plasticity

Three new contributions to the field of multisurface plasticity are presented for general situations with an arbitrary number of nonlinear yield surfaces with hardening or softening. A method for handling linearly dependent flow directions is described. A residual that can be used in a line search is defined. An algorithm that has been implemented and comprehensively tested is discussed in detail. Examples are presented to illustrate the computational cost of various components of the algorithm. The overall result is that a single Newton-Raphson iteration of the algorithm costs between 1.5 and 2 times that of an elastic calculation. Examples also illustrate the successful convergence of the algorithm in complicated situations. For example, without using the new contributions presented here, the algorithm fails to converge for approximately 50% of the trial stresses for a common geomechanical model of sedementary rocks, while the current algorithm results in complete success. Since it involves no approximations, the algorithm is used to quantify the accuracy of an efficient, pragmatic, but approximate, algorithm used for sedimentary-rock plasticity in a commercial software package. Furthermore, the main weakness of the algorithm is identified as the difficulty of correctly choosing the set of initially active constraints in the general setting.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Response tailoring of elasto-plastic trusses

Abstract In this work we tailor the response of trusses loaded beyond their yield limit. The truss structures are modeled using finite strain theory and rate-independent elasto-plasticity. We design trusses with a tailored mechanical response that is between “elastic” and “elastic-ideal-plastic” subject to the volume constraint. The design updates are generated by the gradient-based Method of Moving Asymptotes (MMA) solver and the sensitivities of the response functions are computed using a path-dependent adjoint sensitivity analysis. The computations are performed in Matlab.

42 ENGINEERING↗