Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Numerical techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Impact Testing of Aluminum 2024 and Titanium 6Al-4V for Material Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the FAA William J. Hughes Technical Center. Unique features of this set of data are that all material property data and impact test data are obtained using identical material, the test methods and procedures are extensively documented and all of the raw data is available. Four parallel efforts are currently underway: Measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles conducted by The Ohio State University; development of improved numerical modeling techniques for deformation and failure conducted by The George Washington University; impact testing of flat panels and substructures conducted by NASA Glenn Research Center. This report describes impact testing which has been done on aluminum (Al) 2024 and titanium (Ti) 6Al-4vanadium (V) sheet and plate samples of different thicknesses and with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

Pereira, J. Michael↗
NASA NTRS2016

Overview of the CHarring Ablator Response (CHAR) Code

An overview of the capabilities of the CHarring Ablator Response (CHAR) code is presented. CHAR is a one-, two-, and three-dimensional unstructured continuous Galerkin finite-element heat conduction and ablation solver with both direct and inverse modes. Additionally, CHAR includes a coupled linear thermoelastic solver for determination of internal stresses induced from the temperature field and surface loading. Background on the development process, governing equations, material models, discretization techniques, and numerical methods is provided. Special focus is put on the available boundary conditions including thermochemical ablation, surface-to-surface radiation exchange, and flowfield coupling. Finally, a discussion of ongoing development efforts is presented.

Amar, Adam J.↗
NASA NTRS2016

Overview of the CHarring Ablator Response (CHAR) Code

An overview of the capabilities of the CHarring Ablator Response (CHAR) code is presented. CHAR is a one-, two-, and three-dimensional unstructured continuous Galerkin finite-element heat conduction and ablation solver with both direct and inverse modes. Additionally, CHAR includes a coupled linear thermoelastic solver for determination of internal stresses induced from the temperature field and surface loading. Background on the development process, governing equations, material models, discretization techniques, and numerical methods is provided. Special focus is put on the available boundary conditions including thermochemical ablation and contact interfaces, and example simulations are included. Finally, a discussion of ongoing development efforts is presented.

Amar, Adam J.↗
NASA NTRS2016

ERRATUM: 'MAPPING THE GAS TURBULENCE IN THE COMA CLUSTER: PREDICTIONS FOR ASTRO-H'

The published version of this paper contained an error in Figure 5. This figure is intended to show the effect on the structure function of subtracting the bias induced by the statistical and systematic errors on the line shift. The filled circles show the bias-subtracted structure function. The positions of these points in the left panel of the original figure were calculated incorrectly. The figure is reproduced below (with the original caption) with the correct values for the bias-subtracted structure function. No other computations or figures in the original manuscript are affected.

galaxies: clusters: intracluster medium- methods: ↗
NASA NTRS2017

Orion Exploration Flight Test Post-Flight Inspection and Analysis

The principal mechanism for developing orbital debris environment models, is to make observations of larger pieces of debris in the range of several centimeters and greater using radar and optical techniques. For particles that are smaller than this threshold, breakup and migration models of particles to returned surfaces in lower orbit are relied upon to quantify the flux. This reliance on models to derive spatial densities of particles that are of critical importance to spacecraft make the unique nature of the EFT-1's return surface a valuable metric. To this end detailed post-flight inspections have been performed of the returned EFT-1 backshell, and the inspections identified six candidate impact sites that were not present during the pre-flight inspections. This paper describes the post-flight analysis efforts to characterize the EFT-1 mission craters. This effort included ground based testing to understand small particle impact craters in the thermal protection material, the pre- and post-flight inspection, the crater analysis using optical, X-ray computed tomography (CT) and scanning electron microscope (SEM) techniques, and numerical simulations.

Miller, J. E.↗
NASA NTRS2020

Impact Testing of Inconel 718 for Material Impact Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain-rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition, there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data, and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration (FAA) William J. Hughes Technical Center. Unique features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all of the raw data is available. Four parallel efforts are currently underway. The Ohio State University conducts both measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles. The George Mason University conducts the development of improved numerical modeling techniques for deformation and failure. Glenn conducts the impact testing of flat panels and substructures. This report describes impact testing performed on Inconel 718 sheet and plate samples of different thicknesses with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

J Michael Pereira↗
NASA NTRSDate not supplied

Structured Overset and Unstructured Grid Simulations for the Third AIAA Sonic Boom Prediction Workshop

Predictions using the Launch Ascent and Vehicle Aerodynamics (LAVA) Unstructured and Structured Curvilinear solvers for the Biconvex and C608 geometries are compared in support of the 3rd AIAA Sonic Boom Prediction workshop. Description of the mesh generation techniques and numerical methods are provided along with a comparison of nearfield and far-field predictions with available experimental data as well as other workshop sub-missions. Strong consistency was observed between the Biconvex and C608 nearfield predictions across the two solvers used for this study, as well as validation and verification data. Additionally, near-field and farfield ground signature results using a combination of a truncated computational fluid dynamics (CFD) domain coupled to a mid-field space marching method and propagated to the ground using sBOOM will be discussed. This approach is shown to provide an efficient way to propagate near-field pressure signatures to the ground with the same accuracy as the near-field CFD coupled to sBOOM, but at less computational cost.

CST↗
NASA NTRSDate not supplied

The Metal-Rich Lithology within the Aguas Zarcas Breccia: Characterization, Origin, and Evolution

Carbonaceous chondrites are important since they provide critical insights into the early history of the Solar System. They have experienced a wide range of processes, including aqueous alteration and thermal metamorphism or a combination of both that provide important information about the environment of their evolution. We investigated the petrography, mineralogy, chemistry, and isotopic composition of an unusual “metal-rich lithology” (hereafter Met-1) from Aguas Zarcas using numerous analytical techniques, in order to properly understand its characteristics, affinities, origin and formation history.

I Kerraouch↗
NASA NTRS2021

Detection of Transient Instabilities in Multi-Agent Systems and Swarms

In this paper, we introduce the novel concept of transient instabilities in multi-agent systems and swarms, i.e., a small disturbance leads to increasing-amplitude oscillations throughout the swarm, which results in a large number of interagent collisions. This instability is dominant in the transient phase of the system and it does not appear in the steady-state behavior of the system, as each agent uses Lyapunov-stable feedback control laws. We present a rigorous definition of transient instability in swarms, and discuss its key properties. We also present a sufficient condition to check if a swarm will be transient stable. Using both theoretical techniques and numerical results, we show that a simple Proportional-Integral-Derivative (PID) feedback-tracking control law is not suitable for these applications. We also present a robust control law for Euler- Lagrangian systems that maintains transient stability across static swarms or time-varying reconfiguration in swarms. Both theoretical results and numerical simulations are presented to demonstrate the effectiveness of our proposed approach.

Quadrelli, Marco B.↗
NASA NTRSDate not supplied

Evolution of Astrodynamics for Multibody Environments, Numerical Precision and Dynamical Understanding

The innovative nature of dynamical systems theory and its applications in trajectory design enabled many recent missions by opening up new transfer and capture opportunities to meet mission requirements, reduce fuel costs, and address various launch constraints and contingencies. With a combination of proven numerical methods and an advanced understanding of the dynamics, an ‘experienced’ user can rapidly design multibody and cislunar missions such as Lunar IceCube and Artemis/Themis and relatively quickly conceive trajectory concepts for Sun-Earth mission orbits, such as the Space Weather Follow On-L1 Lissajous orbit—one that can be achieved and maintained.

Dynamical Systems↗
NASA NTRSDate not supplied

Energetic Particles in Geospace: Origin, Dynamics, and Modeling

This presentation explores the origins and dynamics of energetic particles—specifically solar energetic particles (SEPs) and galactic cosmic rays (GCRs) - within the heliosphere and Earth's magnetosphere. We will discuss the fundamental physical processes governing their transport and acceleration in the heliosphere, including interactions with the solar wind and the interplanetary magnetic field. The penetration of these particles into Earth's magnetosphere is examined, emphasizing how the geomagnetic field influences their propagation across the magnetosphere. Key phenomena such as the temporal trapping of SEPs in geospace, reductions in rigidity cutoff during geomagnetic storms, and the enhancement of atmospheric NOx and HOx concentrations - which affect the ozone balance through catalytic reactions—are discussed. The presentation also outlines contemporary numerical modeling techniques used to simulate SEPs and GCRs, providing insights into their complex behaviors under varying geomagnetic conditions.

solar energetic particles↗
NASA NTRSDate not supplied

The Space Weather Follow On – Lagrange 1 Mission

The Space Weather Follow On – Lagrange 1 (SWFO-L1) Observatory will be situated in a Sun-Earth L1 Lissajous orbit with the goal of providing continuous measurements of the space environment and observations of the Sun’s outer atmosphere, and contributing to accurate forecasts of space weather disturbances. Unique to the SWFO-L1 mission are challenges of a rideshare launch, immoderate momentum management delta-V residuals, and spacecraft maneuver design considerations, resulting in specialized operational approach, management, and support.

cislunar↗
NASA NTRSDate not supplied

The Space Weather Follow On – Lagrange 1 Mission

The Space Weather Follow On – Lagrange 1 (SWFO-L1) Observatory will be situated in a Sun-Earth L1 Lissajous orbit with the goal of providing continuous measurements of the space environment and observations of the Sun’s outer atmosphere, and contributing to accurate forecasts of space weather disturbances. Unique to the SWFO-L1 mission are challenges of a rideshare launch, immoderate momentum management delta-V residuals, and spacecraft maneuver design considerations, resulting in specialized operational approach, management, and support.

Dynamical Systems↗
NASA NTRS2026

Impact Testing of 410 Stainless Steel for Material Impact Model Development

A project is underway to develop a consistent set of material properties, impact test data, and failure analysis for a variety of metallic aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration William J. Hughes Technical Center. Particular features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all the raw data are available. Four parallel efforts are currently underway: measurement of material deformation and failure response over a wide range of strain rates and temperatures, failure analysis of material property specimens and impact test articles, development of improved numerical modeling techniques for deformation and failure, and impact testing of flat panels and substructures for model validation. This report describes impact testing performed on 410 stainless steel sheet and plate samples of different thicknesses with two different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

410 Stainless Steel↗
NASA NTRS1974

A generalized-capacity-matrix technique for computing aerodynamic flows

A numerical generalized-capacity-matrix technique is developed for application to aerodynamic flow computations. This technique allows the very fast direct (noniterative) numerical elliptic solvers to be used in problems with arbitrary internal boundaries and with a wide class of boundary conditions, including numerical application of the Kutta condition on an airfoil without iteration. Accuracy, speed, and usefulness of the technique are demonstrated with linear problems for potential flows over airfoil shapes. The method's main advantages, however, can be exploited within iterative procedures for a variety of complex flow problems governed by systems of equations not necessarily elliptic or linear.

Martin, E. D.↗
NASA NTRS1995

Particle-mesh techniques

This is an introduction to numerical Particle-Mesh techniques, which are commonly used to model plasmas, gravitational N-body systems, and both compressible and incompressible fluids. The theory behind this approach is presented, and its practical implementation, both for serial and parallel machines, is discussed. This document is based on a four-hour lecture course presented by the author at the NASA Summer School for High Performance Computational Physics, held at Goddard Space Flight Center.

Macneice, Peter↗