Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Tailoring the crystal structure of TiO{sub 2} thin films from the anatase to rutile phase

TiO{sub 2} films with various Sn concentrations were deposited on quartz substrates using rf reactive magnetron sputtering. The crystal structure was investigated by using x-ray diffraction, Raman spectroscopy, and transmission electron microscopy, and the chemical states of Ti and Sn were analyzed by x-ray absorption near edge structure (XANES) spectroscopy. Without Sn doping, TiO{sub 2} films change the crystal structure from rutile to anatase as the total gas pressure increases in the sputtering deposition. On the other hand, Sn doping induces the transformation of TiO{sub 2} crystalline structure from anatase to rutile phase, where the XANES spectra implied that Sn substitutes into Ti site of rutile TiO{sub 2}. Atomic force microscope analyses revealed that the Sn-doped TiO{sub 2} films exhibited a flat surface with the roughness of approximately 2 nm.

36 MATERIALS SCIENCE↗

Control of bombardment energy and energetic species toward a superdense titanium nitride film

TiN deposited by dc magnetron sputtering has been widely used as a hard mask material for dielectric patterning in multilevel Cu interconnects. Typically inside a ''poison-mode'' regime, the film density is 4.5-4.9 g/cm{sup 3}. The microstructure, varying from columnar structure to nanocrystalline, is controlled by both thermodynamics and surface kinetics through ionization, substrate bias, target voltage, etc. A relatively low density film can be correlated with a porous columnar structure, low mechanical robustness, and weak resistance to plasma etching. However, with controlled growth, an applied substrate bias does not create resputtering and crystal defects. Instead, the authors create film with a maximum density of 5.3 g/cm{sup 3}. In this high density film, carrier scatterings through grain boundary are greatly suppressed and the film resistivity is as low as 95 {mu}{Omega} cm, which brings additional benefits as a conductive capping layer. As it is deposited at room temperature, the process minimizes the thermal budget to the underlying low-k dielectric materials to be patterned.

36 MATERIALS SCIENCE↗

IMPURITY AND TRACER DIFFUSION STUDIES IN MAGNESIUM AND ITS ALLOYS

An Integrated Computational Materials Engineering (ICME) approach for optimizing processing routes for Mg-alloys requires reliable thermodynamic and diffusion databases. We are developing an impurity and tracer diffusion database using both stable and unstable isotopes for Mg and its alloys. In this study, Al impurity diffusion in pure polycrystalline Mg (99.9%) was examined using the thin film method. Approximately 500 nm thick Al films were deposited on in-situ RF plasma-cleaned polycrystalline Mg by DC magnetron sputtering from pure Al (99.9%) targets. Specimens were then diffusion annealed at 300, 350 and 400 C in quartz capsules that were evacuated to 10-8 Torr and backfilled with Ar-H2 mixtures. Concentration profile of Al diffusion profiles into single phase Mg was determined by depth-profiling technique using secondary ion mass spectroscopy. The Al impurity diffusion coefficients were determined as a function of temperature

36 MATERIALS SCIENCE↗

Giant magnetoelectric coupling interaction in BaTiO{sub 3}/BiFeO{sub 3}/BaTiO{sub 3} trilayer multiferroic heterostructures

Multiferroic trilayer thin films of BaTiO{sub 3}/BiFeO{sub 3}/BaTiO{sub 3} were prepared by RF-magnetron sputtering technique at different thicknesses of BiFeO{sub 3} layer. A pure phase polycrystalline growth of thin films was confirmed from X-ray diffraction results. The film showed maximum remnant electric polarization (2P{sub r}) of 13.5 μC/cm{sup 2} and saturation magnetization (M{sub s}) of 61 emu/cc at room temperature. Thermally activated charge transport dominated via oxygen vacancies as calculated by their activation energy, which was consistent with current–voltage characteristics. Magnetic field induced large change in resistance and capacitance of grain, and grain boundary was modeled by combined impedance and modulus spectroscopy in the presence of varied magnetic fields. Presence of large intrinsic magnetoelectric coupling was established by a maximum 20% increase in grain capacitance (C{sub g}) with applied magnetic field (2 kG) on trilayer having 20 nm BiFeO{sub 3} layer. Substantially higher magnetoelectric coupling in thinner films has been observed due to bonding between Fe and Ti atoms at interface via oxygen atoms. Room temperature magnetoelectric coupling was confirmed by dynamic magnetoelectric coupling, and maximum longitudinal magnetoelectric coupling of 515 mV/cm-Oe was observed at 20 nm thickness of BiFeO{sub 3}. The observed magnetoelectric properties are potentially useful for novel room temperature magnetoelectric and spintronic device applications for obtaining higher voltage at lower applied magnetic field.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sputtering as a Technique for Applying Tribological Coatings

Friction and wear induced mechanical failures may be controlled to extend the life of tribological components through the interposition of selected solid materials between contacting surfaces. Thin solid films of soft and hard materials are appropriate to lower friction and enhance the wear resistance of precision tribo-elements. Thin film coating technologies that have been developed may be used to interpose thin solid layers between contacting surfaces to reduce friction or to extend wear life. Film deposition technologies developed include chemical vapor deposition (CVD) and physical vapor deposition (PVD). Sputter coating is a PVD process for thin film deposition. It allows close control of coating thickness and composition and is well-suited for the deposition of tribological coatings. In this paper, the utility of magnetron sputtering for the deposition of tribological coatings is examined. Experimental results obtained when coated bodies are tested under a number of tribological operating conditions are presented. It is shown that when film adhesion problems are resolved, sputtering can be an effective means of depositing tribological coatings.

S Ramalingam↗

Self-assembly of Ge quantum dots on periodically corrugated Si surfaces

The fabrication of regularly ordered Ge quantum dot arrays on Si surfaces usually requires extensive preparation processing, ensuring clean and atomically ordered substrates, while the ordering parameters are quite limited by the surface properties of the substrate. Here, we demonstrate a simple method for fabrication of ordered Ge quantum dots with highly tunable ordering parameters on rippled Si surfaces. The ordering is achieved by magnetron sputter deposition, followed by an annealing in high vacuum. We show that the type of ordering and lattice vector parameters of the formed Ge quantum dot lattice are determined by the crystallographic properties of the ripples, i.e., by their shape and orientation. Moreover, the ordering is achieved regardless the initial amorphisation of the ripples surface and the presence of a thin oxide layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nb₃Sn Coating of a 2.6 GHz SRF Cavity by Sputter Deposition Technique

Nb₃Sn is of interest as a coating for SRF cavities due to its higher transition temperature Tc ~18.3 K and superheating field Hsh ~400 mT, both are twice that of Nb. Nb₃Sn coated cavities can achieve high-quality factors at 4 K and can replace the bulk Nb cavities operated at 2 K. A cylindrical magnetron sputtering system was built, commissioned, and used to deposit Nb₃Sn on the inner surface of a 2.6 GHz single-cell Nb cavity. With two identical cylindrical magnetrons, this system can coat a cavity with high symmetry and uniform thickness. Using Nb-Sn multilayer sequential sputtering followed by annealing at 950°C for 3 hours, polycrystalline Nb₃Sn films were first deposited at the equivalent positions of the cavity’s beam tubes and equator. The film’s composition, crystal structure, and morphology were characterized by energy dispersive spectroscopy, X-ray diffraction, and atomic force microscopy. The Tc of the films was measured by the four-point probe method and was 17.61 to 17.76 K. Based on these studies, ~1.2 micron thick Nb₃Sn was deposited inside a 2.6 GHz Nb cavity. We will discuss first results from samples and cavity coatings, and the status of the coating system.

43 PARTICLE ACCELERATORS↗

Influence of Al{sub 2}O{sub 3} layer insertion on the electrical properties of Ga-In-Zn-O thin-film transistors

To investigate the influence of ionic/covalent interface of Al{sub 2}O{sub 3}/SiO{sub 2} gate insulator on the electrical properties of thin-film transistors (TFTs) with ionic Ga-In-Zn-O (GIZO) semiconducting channel layers, Al{sub 2}O{sub 3} layers of different thickness were introduced between SiO{sub 2} and GIZO using plasma-enhanced atomic layer deposition. The GIZO layers were obtained by DC magnetron sputtering using a GIZO target (Ga:In:Zn = 1:1:1 mol. %). The GIZO TFTs with an Al{sub 2}O{sub 3}/SiO{sub 2} gate insulator exhibited positive threshold voltage (V{sub th}) shift (about 1.1 V), V{sub th} hysteresis suppression (0.23 V), and electron mobility degradation (about 13%) compared with those of a GIZO TFT with SiO{sub 2} gate insulator by the influence of ionic/ionic and ionic/covalent interface at Al{sub 2}O{sub 3}/GIZO and Al{sub 2}O{sub 3}/SiO{sub 2}, respectively. To clarify the origin of the positive V{sub th} shift, the authors estimated the shifts of flatband voltage (0.4 V) due to the dipole and the fixed charge (−1.1 × 10{sup 11}/cm{sup 2}) at Al{sub 2}O{sub 3}/SiO{sub 2} interface, from capacitance–voltage data for Pt/Al{sub 2}O{sub 3}/SiO{sub 2}/p-Si capacitors. Based on these experimental data, the authors found that the positive V{sub th} shift (1.1 V) could be divided into three components: the dipole (−0.4 V) and fixed charge (0.15 V) at the SiO{sub 2}/Al{sub 2}O{sub 3} interface, and the fixed charge (1.35 V) at the Al{sub 2}O{sub 3}/GIZO interface. Finally, it is noted that heterointerface of SiO{sub 2}/Al{sub 2}O{sub 3}/GIZO stacks is important not only to recognize mechanism of V{sub th} shift but also to design future TFTs with high-k dielectrics and low operating voltage.

42 ENGINEERING↗

Characteristics of Al-doped ZnO thin films prepared in Ar + H{sub 2} atmosphere and their vacuum annealing behavior

The microstructure and electrical–optical properties of Al-doped ZnO (AZO) films have been studied as a function of H{sub 2} flux in the magnetron sputtering process at 150 °C and postannealing temperature in vacuum. As H{sub 2} flux increases in the sputtering gas, the AZO films deposited have a (002) preferred orientation rather than the mixed (100) and (002) orientations, the grain size shows a tendency to first increase then decrease, and (002) diffraction peak position is inclined to shift to higher angles first then to lower angles. The resistivity of the films first decreases then increases with H{sub 2} flux, and the lowest resistivity of 4.02 × 10{sup −4}Ω cm is obtained at a H{sub 2} flux of 10 sccm. The average transmittance in the visible region shows little dependence on H{sub 2} flux. As a whole, the AZO films with higher values of figure of merit are obtained when the H{sub 2} flux is in the range of 6–12 sccm. The AZO films deposited in Ar and Ar + H{sub 2} exhibit different annealing behaviors. For the AZO film deposited in Ar, the grain size gradually increases, the stresses are relaxed, the resistivity first decreases then increases, and the average transmittance in the visible region is unchanged initially then somewhat decreased as annealing temperature is increased. The optimum annealing temperature for improving properties of AZO films deposited in Ar is 300 °C. For the AZO films deposited in Ar + H{sub 2}, annealing does not significantly change the microstructure but increases the resistivity of the films; the average transmittance in the visible region remains unchanged initially but greatly reduced with further increase in annealing temperature. The carrier transport in the as-deposited and annealed films appears to be controlled by a mechanism of grain boundary scattering, and the value of E{sub g} increases with the increase in carrier concentration due to Burstein–Moss effect.

36 MATERIALS SCIENCE↗

Integrating atomic layer deposition and ultra-high vacuum physical vapor deposition for in situ fabrication of tunnel junctions

Atomic Layer Deposition (ALD) is a promising technique for growing ultrathin, pristine dielectrics on metal substrates, which is essential to many electronic devices. Tunnel junctions are an excellent example which require a leak-free, ultrathin dielectric tunnel barrier of typical thickness around 1 nm between two metal electrodes. A challenge in the development of ultrathin dielectric tunnel barriers using ALD is controlling the nucleation of dielectrics on metals with minimal formation of native oxides at the metal surface for high-quality interfaces between the tunnel barrier and metal electrodes. This poses a critical need for integrating ALD with ultra-high vacuum (UHV) physical vapor deposition. In order to address these challenges, a viscous-flow ALD chamber was designed and interfaced to an UHV magnetron sputtering chamber via a load lock. A sample transportation system was implemented for in situ sample transfer between the ALD, load lock, and sputtering chambers. Using this integrated ALD-UHV sputtering system, superconductor-insulator-superconductor (SIS) Nb-Al/Al{sub 2}O{sub 2}/Nb Josephson tunnel junctions were fabricated with tunnel barriers of thickness varied from sub-nm to ∼1 nm. The suitability of using an Al wetting layer for initiation of the ALD Al{sub 2}O{sub 3} tunnel barrier was investigated with ellipsometry, atomic force microscopy, and electrical transport measurements. With optimized processing conditions, leak-free SIS tunnel junctions were obtained, demonstrating the viability of this integrated ALD-UHV sputtering system for the fabrication of tunnel junctions and devices comprised of metal-dielectric-metal multilayers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗

Annealing effects on the ferromagnetic resonance linewidths of sputter-deposited Fe{sub 100−x}Co{sub x}(001) thin films (x < 11)

Effects of post-growth annealing on the magnetic damping of 3d transition alloy thin films were investigated. Fe{sub 100−x}Co{sub x} (x < 11 at. %) thin films were epitaxially deposited on GaAs(001) substrates by rf magnetron sputtering, and some of them were annealed without exposing to atmosphere. Electrical measurement showed that in-plane resistivity was smaller in the annealed films than in the as-deposited ones, indicating that the annealing mitigates crystalline imperfections and leads to reduced electron scattering rates. Magnetic damping was evaluated by the peak widths of ferromagnetic resonance (FMR) spectra obtained by a conventional Q-band spectrometer. Comparison of as-deposited and annealed specimens showed that the damping was decreased by annealing. Combined with the electrical and FMR measurements, these observations are consistent with the theoretical predictions that crystalline imperfections strongly influence the magnetic damping, both in intrinsic and extrinsic origins.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High piezoelectricity of Pb(Zr,Ti)O{sub 3}-based ternary compound thin films on silicon substrates

Pb(Zr,Ti)O{sub 3} (PZT)-based ternary compound thin films, 0.06PMnN-0.94PZT(50/50) (PMnN-PZT), are deposited on Si-based heterostructures by rf magnetron sputtering system. The intrinsic PZT(50/50) thin films are also deposited on the same kind of substrates for comparison. The PMnN-PZT thin films show the similar polycrystalline structures as those of PZT with highly (111) oriented perovskite phase. The PMnN-PZT thin films show excellent piezoelectricity and ferroelectricity which are distinctly better than those of PZT thin films prepared with the same deposition conditions. Besides, the cantilevers of PMnN-PZT thin films on the heterostructure substrates also exhibit higher sensitivities than the PZT thin film cantilevers.

36 MATERIALS SCIENCE↗

Metal-insulator-semiconductor barriers with a nanometer-thick aluminum nitride insulator on p-type silicon

The state of the interface between p-silicon and a nanometer-thick insulator is analyzed. DLTS spectra, obtained with deep centers in the bulk of the structure and its surface states recharged, are examined. The nature of the noise as a function of the reverse bias is determined for evaluating the possibility of using the structure as a nuclear radiation detector. A conclusion is drawn that the barrier used in the structure has a higher quality when nanometer-thick aluminum nitride films are deposited by dc, rather than ac, magnetron sputtering.

36 MATERIALS SCIENCE↗

Optical transparency and electrical conductivity of nonstoichiometric ultrathin In{sub x}O{sub y} films

The effect of thickness and composition on the electrical conductivity and optical transparency, mainly in the infrared, of ultrathin In{sub x}O{sub y} films was studied. In{sub x}O{sub y} films 35-470 A thick with oxygen atomic fractions of {approx}0.3 and {approx}0.5 were prepared via dc magnetron sputtering. All films were polycrystalline, consisting of only the cubic bixbiyte phase of In{sub 2}O{sub 3}. The average grain size of the films increased from 30 to 95 nm as the film thickness increased. The weak dependence of the electrical conductivity on the frequency and the low activation energies for conduction, a few hundredths of an eV, provided an indication that free band conduction was the primary electrical conduction mechanism in the case of all ultrathin In{sub x}O{sub y} films. It was found that introducing a high degree of nonstoichiometry in the form of oxygen deficiency did not help improve the electrical conductivity, since not all vacancies contributed two free electrons for conduction and due to impurity scattering. The optical nature of these films, studied mainly by ellipsometry, was found to be dependent on the film's composition and thickness. In the infrared, the dielectric function of all In{sub x}O{sub y} films was consistent with the Drude model, inferring that the transparency loss in this region was a result of free charge carriers. In the visible however, In{sub x}O{sub y} films under 170 A, which had an oxygen atomic fraction of {approx}0.5, were modeled by extending the Drude model to the shorter wavelengths. Films over 170 A, with the same composition, were modeled using the Cauchy dispersion model, meaning that no absorption was measured. These results indicate that, optically, under specific compositions, ultrathin In{sub x}O{sub y} films undergo a transition from metalliclike behavior to dielectric behavior with increasing film thickness. Using a figure of merit approach, it was determined that a nonstoichiometric 230 A thick In{sub x}O{sub y} film, with an oxygen atomic fraction of {approx}0.3, had the best combination of conductivity and transparency, namely, absorption of less than 20% in the infrared, about 10% in the visible, and electrical resistance of only 230 {Omega} at 20 kHz. Such a film may be classified as a highly conductive transparent oxide even in the infrared.

36 MATERIALS SCIENCE↗

Technique for the Formation of Antireflection Coatings Based on ITO Films

A technique for forming transparent conducting indium-tin-oxide films for applications, which require high current densities, are considered. These films have to combine a good surface conductivity with an increased transmittance of radiation within a wide wavelength range. A two-stage process is designed to fabricate such coatings: at the first stage, a dense indium-tin-oxide film with high electrical conductivity is formed; then, an additional antireflection layer of the same material is deposited. Possible methods for optimizing these additional indium-tin-oxide films obtained by forming nanostructured self-assembled coatings on the surface of dense films are investigated. It is shown that the best light extraction over a wide wavelength range is provided by the composite film-deposition technique, which consists in the deposition of self-assembled nanostructured coatings by electron-beam evaporation on a hot substrate and the further filling of voids by magnetron sputtering at room temperature. Since the optical properties of the obtained antireflection coatings depend on the mass ratio of materials deposited at each stage, the technique makes it possible to optimize the film properties on the basis of problems specified by the area of their application. Computer simulation of the behavior of the material distribution in the structure of the studied coatings confirms the ability of the method of combined film deposition to form the smoothest character of the change in the effective refractive index of the coating structure, which leads to the most efficient extraction of optical-range light.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Enhancement of spin-asymmetry by L2{sub 1}-ordering in Co{sub 2}MnSi/Cr/Co{sub 2}MnSi current-perpendicular-to-plane magnetoresistance devices

Co{sub 2}MnSi/Cr/Co{sub 2}MnSi (001)-fully epitaxial current-perpendicular-to-plane giant magnetoresistance (CPP-GMR) devices were fabricated via an UHV magnetron sputtering system. The relationship between the degree of chemical ordering in Co{sub 2}MnSi (CMS) and the CPP-GMR characteristics was investigated systematically against the annealing temperature of the devices. X-ray diffraction profiles and reflection high-energy electron diffraction images indicated that annealing improved L2{sub 1}-ordering. The MR ratio also increased upon annealing and the maximum MR ratio of 5.2% and {delta}RA of 6.5 m{omega} {mu}m{sup 2} were achieved by annealing at 400 deg. C. These results indicate that promoting the degree of L2{sub 1}-ordering in CMS enhances the bulk and/or interface spin-asymmetry coefficients.

36 MATERIALS SCIENCE↗

Momentum transfer driven textural changes of CeO{sub 2} thin films

The influence of the target erosion depth on the film texture was investigated during DC reactive magnetron sputter deposition of CeO{sub 2} thin films. Three fluxes towards the substrate surface (the relative negative oxygen ion flux, the material flux, and the energy flux) were measured and related to the ongoing erosion of a cerium target. As the deposition rate increased for more eroded targets, both the energy flux and the negative ion flux decreased. Cerium oxide thin films that were deposited at different target erosion states, exhibited a change in preferential crystalline orientation from [200] to [111]. This textural change cannot be explained in terms of the energy per arriving atom concept. Instead, it is shown that the momentum of the high energetic negative ions is an essential condition to clarify the witnessed trends.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗