SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The development of elastomer-containing photoactive block copolymers with regulated rigid-block lengths results in organic solar cells with high power conversion efficiency (17.3%) and mechanical robustness (toughness = 1.8 MJ m −3 ).
We have observed axisymmetric Bernstein modes in an infinite-length particle-in-cell code simulation of a non-neutral plasma. The plasmas considered were in global thermal equilibrium and there were at least 50 Larmor radii within the plasma radius. The density of the plasma in the simulation is parameterized by β, the ratio of the central density to the density at the Brillouin limit. These modes have m = 0 and k{sub z}=0, where the eigenfunctions vary as e{sup i(mθ+k{sub z}z)}. The modes exist both near the Coriolis-shifted (by the plasma rotation) upper-hybrid frequency, ω{sub uh}=√(ω{sub c}{sup 2}−ω{sub p}{sup 2}), and near integer multiples (2, 3, etc.) of the Coriolis-shifted cyclotron frequency (called the vortex frequency, ω{sub v}=√(ω{sub c}{sup 2}−2ω{sub p}{sup 2})). The two modes near ω{sub uh} and 2ω{sub v} are the main subject of this paper. The modes observed are clustered about these two frequencies and are separated in frequency at low plasma density roughly by δω≈10(r{sub L}/r{sub p}){sup 2}ω{sub p}{sup 2}/ω{sub c}. The radial velocity field of the modes has a J{sub 1}(kr) dependence in the region of the plasma where the density is nearly constant. For any given density, there are three classes of modes that exist: (1) The fundamental mode is slightly above the upper-hybrid frequency, (2) the upper branch is above the higher of ω{sub uh} and 2ω{sub v}, and (3) the lower branch is below the lower of ω{sub uh} and 2ω{sub v}, with similar values of k for both the upper and the lower frequency branches. The modes are fully kinetic and the resulting pressure tensor has significant anisotropy, including off-diagonal terms. A Vlasov analysis of these modes considering only particle resonances up to 2ω{sub v} produces a radial mode differential equation whose solution agrees well with the simulations, except at high density (β greater than about 0.9) where higher-order resonances become important.
A question of considerable interest to cell membrane biology is whether phase segregated domains across an asymmetric bilayer are strongly correlated with each other and whether phase segregation in one leaflet can induce segregation in the other. We answer both these questions in the affirmative, using an atomistic molecular dynamics simulation to study the equilibrium statistical properties of a 3-component asymmetric lipid bilayer comprising an unsaturated palmitoyl-oleoyl-phosphatidyl-choline, a saturated sphingomyelin, and cholesterol with different composition ratios. Our simulations are done by fixing the composition of the upper leaflet to be at the coexistence of the liquid ordered (l{sub o})-liquid disordered (l{sub d}) phases, while the composition of the lower leaflet is varied from the phase coexistence regime to the mixed l{sub d} phase, across a first-order phase boundary. In the regime of phase coexistence in each leaflet, we find strong transbilayer correlations of the l{sub o} domains across the two leaflets, resulting in bilayer registry. This transbilayer correlation depends sensitively upon the chain length of the participating lipids and possibly other features of lipid chemistry, such as degree of saturation. We find that the l{sub o} domains in the upper leaflet can induce phase segregation in the lower leaflet, when the latter is nominally in the mixed (l{sub d}) phase.
Local-hybrid functionals involve position-dependent mixing of Hartree-Fock and density-functional exchange, which should allow improved performance relative to conventional hybrids by reducing the inherent delocalization error and improving the long-range behaviour. Herein, the same-spin correlation length, obtained from the Fermi-hole radius, is used as the mixing parameter. The performance of the resulting local-hybrid functional is assessed for standard thermochemical and kinetics benchmarks. The local hybrid is shown to perform significantly better than the corresponding global hybrid in almost all cases.
We consider the problem of non-resonant detection of terahertz signals in a short gate length field-effect transistor having a two-dimensional electron channel with zero external bias between the source and the drain. The channel resistance, gate-channel capacitance, and quadratic nonlinearity parameter of the transistor during detection as a function of the gate bias voltage are studied. Characteristics of detection of the transistor connected in an antenna with real impedance are analyzed. The consideration is based on both a simple one-dimensional model of the transistor and allowance for the two-dimensional distribution of the electric field in the transistor structure. The results given by the different models are discussed.
The electrostatic surface potential (ESP) of prion oligomers has critical influences on the aggregating processes of the prion molecules. The atomic force microscopy (AFM) and structural simulation were combined to investigate the molecular basis of the full-length human recombinant prion oligomerization on mica surfaces. The high resolution non-intrusive AFM images showed that the prion oligomers formed different patterns on mica surfaces at different buffer pH values. The basic binding units for the large oligomers were determined to be prion momoners (Ms), dimers (Ds), and trimers (Ts). The forming of the D and T units happened through the binding of hydrophobic β-sheets of the M units. In contrast, the α-helices of these M, D, and T units were the binding areas for the formation of large oligomers. At pH 4.5, the binding units M, D, and T showed clear polarized ESP distributions on the surface domains, while at pH 7.0, they showed more evenly distributed ESPs. Based on the conformations of oligomers observed from AFM images, the D and T units were more abundantly on mica surface at pH 4.5 because the ESP re-distribution of M units helped to stabilize these larger oligomers. The amino acid side chains involved in the binding interfaces were stabilized by hydrogen bonds and electrostatic interactions. The detailed analysis of the charged side chains at pH 4.5 indicated that the polarized ESPs induced the aggregations among M, D, and T to form larger oligomers. Therefore, the hydrogen bonds and electrostatic interactions worked together to form the stabilized prion oligomers.
Here the C 1 B 2 state of SO 2 has a double-minimum potential in the antisymmetric stretch coordinate, such that the minimum energy geometry has nonequivalent SO bond lengths. The asymmetry in the potential energy surface is expressed as a staggering in the energy levels of the v' 3 progression. We have recently made the first observation of low-lying levels with odd quanta of v' 3 , which allows us--in the current work--to characterize the origins of the level staggering. Our work demonstrates the usefulness of low-lying vibrational level structure, where the character of the wavefunctions can be relatively easily understood, to extract information about dynamically important potential energy surface crossings that occur at much higher energy. The measured staggering pattern is consistent with a vibronic coupling model for the double-minimum, which involves direct coupling to the bound 2 1 A 1 state and indirect coupling with the repulsive 3 1 A 1 state. The degree of staggering in the v' 3 levels increases with quanta of bending excitation, which is consistent with the approach along the C state potential energy surface to a conical intersection with the 2 1 A 1 surface at a bond angle of ~145°.
The recalcitrance of lignocellulosic biomass poses a major challenge that hinders the economical utilization of biomass for the production of biofuel, plastics, and chemicals. Ionic liquids have become a promising solvent that addresses many issues in both the pretreatment process and the hydrolysis of the glycosidic bond for the deconstruction of cellulosic materials. However, to make the use of ionic liquids economically viable, either the cost of ionic liquids must be reduced, or a less expensive solvent (e.g., water) may be added to reduce the overall amount of ionic liquid used in addition to reducing the viscosity of the binary liquid mixture. In this work, we employ atomistic molecular dynamics simulations to investigate the impact of water dilution on the overall liquid structure and properties of three imidazolium based ionic liquids. It is found that ionic liquid-water mixtures exhibit characteristics that can be grouped into two distinct regions, which are a function of the ionic liquid concentration. The trends observed in each region are found to correlate with the ordering in the local structure of the ionic liquid that arises from the dynamic interactions between the ion pairs. Simulation results suggest that there is a high level of local ordering in the molecular structure at high concentrations of ionic liquids that is driven by the aggregation of the cationic tails and the anion-water interactions. It is found that as the concentration of ionic liquids in the binary mixture is decreased, there is a point at which the competing self and cross interaction energies between the ionic liquid and water shifts away from a cation-anion dominated regime, which results in a significant change in the mixture properties. This break point, which occurs around 75% w/w ionic liquids, corresponds to the point at which water molecules percolate into the ionic liquid network disrupting the ionic liquids’ nanostructure. It is observed that as the cationic alkyl tail length increases, the changes in the binary mixtures’ properties become more pronounced.
The traditional method for electron lifetime measurements of CdZnTe (CZT) detectors relies on using the Hecht equation. The procedure involves measuring the dependence of the detector response on the applied bias to evaluate the μτ product, which in turn can be converted into the carrier lifetime. Despite general acceptance of this technique, which is very convenient for comparative testing of different CZT materials, the assumption of a constant electric field inside a detector is unjustified. In the Hecht equation, this assumption means that the drift time would be a linear function of the distance. This condition is not fulfilled in practice at low applied biases, where the Hecht equation is most sensitive to the μτ product. As a result, researchers usually take measurements at relatively high biases, which work well in the case of the low μτ-product material, <10 -3 cm 2 /V, but give significantly underestimated values for the case of high μτ-product crystals. In this paper, we applied the drift-time method to measure the electron lifetimes in long-drift-length (4 cm) standard-grade CZT detectors produced by the Redlen Technologies. We found that the electron μτ product of tested crystals is in the range 0.1–0.2 cm 2 /V, which is an order of the magnitude higher than any value previously reported for a CZT material. Finally, in comparison, using the Hecht equation fitting, we obtained μτ = 2.3 × 10 -2 cm 2 /V for a 2-mm thin planar detector fabricated from the same CZT material.
We applied time-resolved pump-probe spectroscopy based on free carrier absorption and light diffraction on a transient grating for direct measurements of the carrier lifetime and diffusion coefficient D in high-resistivity single crystal CdTe (codoped with In and Er). The bulk carrier lifetime t decreased from 670 +/-50 ns to 60 +/- 10 ns with increase of excess carrier density N from 10 16 to 5 x 10 18 cm -3 due to the excitation-dependent radiative recombination rate. In this N range, the carrier diffusion length dropped from 14 um to 6 um due to lifetime decrease. Modeling of in-depth (axial) and in-plane (lateral) carrier diffusion provided the value of surface recombination velocity S = 6 x 10 5 cm/s for the untreated surface. At even higher excitations, in the 10 19 -3 x 10 20 cm -3 density range, D increase from 5 to 20 cm^2/s due to carrier degeneracy was observed.
The molecular-frame photoelectron angular distributions (MFPADs) in O 1s photoemission from CO 2 molecule were measured. Patterns due to photoelectron diffractions were observed in the MFPADs. The polarization-averaged MFPADs were compared with theoretical calculation and were found to be useful in determining the molecular bond-length, which is a component to determine molecular structures.
Here, we study experimentally the temperature evolution of the thickness of the interfacial layer, L int (T), between bulk matrices and the surface of nanoparticles in nanocomposites through broadband dielectric spectroscopy. Analyses revealed a power-law dependence between the logarithm of structural relaxation time in the interfacial layer, τ int (T), and the L int (T): ln τ i n t ( T ) / τ 0 ∝ L i n t β ( T ) / T , with τ 0 ~ 10 –12 s, and β index ~0.67 at high temperatures and ~1.7 at temperatures close to the glass transition temperature. In addition, our analysis revealed that the L int (T) is comparable to the length scale of dynamic heterogeneity estimated from previous nonlinear dielectric measurements and the four-point NMR [ξ NMR (T)], with L int (T) ~ ξ NMR (T). These observations may suggest a direct correlation between the L int (T) and the size of the cooperatively rearranging regions and have strong implications for understanding the dynamic heterogeneity and cooperativity in supercool liquids and their role in interfacial dynamics.
Slow electrons (with energy below 10 eV) play an important role in nature and technology. For instance, they are believed to initiate solubility change in extreme ultraviolet resists. Depending on their mobility, such secondary electrons can lead to image blur and degradation of patterning resolution. Hence, it is important to characterize the transport of slow electrons by measuring parameters such as the effective attenuation length (EAL). In this work, we present a technique that allows for prompt characterization of EAL in polymer films. In this experiment, slow electrons are generated in a substrate upon absorption of x-ray photons. The attenuation of electron flux by a polymer film is measured as a function of film thickness, allowing for the determination of EAL for slow electrons. We illustrate this method with poly(hydroxy styrene) and poly(methyl metacrylate) films. Furthermore, we propose an improvement for this technique that would enable the measurement of EAL as a function of electron kinetic energy.
This Perspective outlines theoretical, simulation, and experimental studies linking electron emission and gas breakdown. Many studies have investigated field emission-driven microscale gas breakdown, including recent reviews [Garner et al., IEEE Trans. Plasma Sci. 48, 808–824 (2020); Fu et al., Plasma Res. Express 2, 013001 (2020)]. This Perspective focuses on generalizing field emission-driven microscale gas breakdown to consider the contribution of other forms of electron emission, specifically thermionic and space-charge limited. Recent theoretical studies have unified thermionic, field, and space-charge limited emission with and without collisions to derive “nexuses” where the individual solutions match, indicating transitions in the mechanisms. Reducing device size to nanoscale at atmospheric pressure leads to a transition from field emission to space-charge limited emission for nitrogen at ~250 nm. This Perspective summarizes the derivation of these nexuses and future extensions. We next describe simulation and theoretical studies for field emission-driven microscale gas breakdown and highlight how the nexus theory may be integrated to account for temperature, space-charge, and pulse parameters. Finally, we summarize the development of optical techniques to assess microscale gas breakdown and recent nanoscale experiments at atmospheric pressure that suggest that space-charge may begin to contribute to field emission prior to gas breakdown. We highlight the combination of theory, simulation, and experiment to link electron emission and gas breakdown mechanisms across length, pressure, and temperature scales for applications that include vacuum electronics, pulsed power, and medicine.
Accurate characterization of the intrinsic contact resistance is important for the optimization of organic thin-film transistors (OTFTs), especially in devices with high gate capacitance density. This study reports on a method for the extraction of the intrinsic, or gate-voltage independent, contact resistance from OTFTs. In contrast to the transfer length method (TLM), this method can be applied to devices with a single geometry. The method is an extension of the previously reported Y-function method and combines the model proposed by S. Luan et al. to analyze the effect of the gate voltage on the contact resistance. Here, this method is first applied to OTFTs with a bottom-gate top-contact geometry having varying gate capacitance density values. The intrinsic contact resistance is found to decrease with increased gate capacitance density with values ranging between 4 kΩcm and under 1 kΩcm when the gate capacitance is changed from 36.6 nF/cm 2 to 231.7 nF/cm 2 , respectively. These values are in good agreement with those obtained using TLM experiments. The new method is also shown to be applicable to OTFTs with top-gate bottom contact geometry.
We report a first-of-its-kind model calibration was performed using Sandia National Laboratories’ high-throughput initiation (HTI) experiment for two types of vapor-deposited explosive films consisting of hexanitrostilbene (HNS) or pentaerythritol tetranitrate (PETN). These films exhibit prompt initiation, and they reach steady detonation at sub-millimeter length scales. Following prior work on HNS, we test the hypothesis of approximating these explosive films as fine-grained homogeneous solids with simple Arrhenius kinetics burn models. The model calibration process is described herein using a single-step as well as a two-step Arrhenius rate law, and it consists of systematic parameter sampling leading to a reduction in the model degrees of freedom. Multiple local minima are observed; results are given for seven different optimized parameter sets. Each model set is further evaluated in a two-dimensional simulation of the critical failure thickness for a sustained detonation. Overall, the two-step Arrhenius kinetics model captures the observed behavior for HNS; however, neither model produces a good fit to the PETN data. We hypothesize that the HTI results for PETN correspond to a heterogeneous response, owing to the smaller reaction zone of PETN compared to HNS (i.e., it does not homogenize the fine-grained hot spots as well). Future work should consider using the ignition and growth model for PETN, as well as other reactive burn models such as xHVRB, AWSD, PiSURF, and CREST.
The effects of pre-plasmas on the electron beam directionality was experimentally and numerically investigated. Single material and layered targets made of Ti and/or CH were used to simultaneously measure high-energy (≥3 MeV) electrons along two directions, pre-pulse energy and pre-plasma density. The electron directionality is quantified by using a new parameter, the electron energy ratio of the total kinetic energies along the two directions. Measurements and radiation–hydrodynamic (RH) simulations show that a large (≥3.5 μm) plasma scale length at the critical surface enhances electrons along the laser axis, and such pre-plasma conditions could only be achieved with the CH targets. Particle-in-cell simulations were performed on the RH generated pre-plasmas from Ti and CH targets, and the results show that the CH target provided conditions for higher forward momentum gains by electrons. First, the CH target allowed longer distances for electrons to interact with laser. Second, the intense laser pulse modified the critical surface, but the resulting surface differed. The CH target resulted in a smooth surface where a retro-reflection was observed while the Ti target resulted in a rippled surface that scattered the reflected light. As results, the CH electrons gained higher forward momentum via a direct-laser-acceleration in the counter propagating laser fields. So the results presented in this article show a way of controlling the high-energy electron directionality.
Electron emission spectroscopy was performed on metalorganic chemical vapor deposition grown p-n – -n + junctions with p-thicknesses ranging from 50 to 300 nm, doped with [Mg] = 3.5 × 10 19 cm –3 . By measuring the decreasing emitted electron intensity from a cesiated p-GaN surface with increasing p-thickness, we were able to extract the minority carrier diffusion length of electron in p-type GaN, L e = 26 ± 3 nm. The measured value is in good agreement with literature reported values. In conclusion, the extrapolated electron current at the n – region–p-GaN interface is in reasonable agreement with the simulated electron current at the interface.