Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRAIN ORIENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Granular L1{sub 0} FePt:TiO{sub 2} (001) nanocomposite thin films with 5 nm grains for high density magnetic recording

FePt:TiO{sub 2} (001) thin films were deposited on CrRu/MgO underlayers by dc magnetron cosputtering. The effects of TiO{sub 2} content on microstructure and magnetic properties of the epitaxial FePt (001) films were studied. Experimental results showed that even with 20 vol % TiO{sub 2} doping, FePt films could keep a (001) preferred orientation and perpendicular anisotropy. The FePt:TiO{sub 2} (001) film with 5 nm grain size, adjustable coercivity, and reduced exchange coupling was obtained by doping 20 vol % TiO{sub 2} into FePt film, showing great potential as low noise ultrahigh density perpendicular magnetic recording media.

36 MATERIALS SCIENCE↗

Effects of Strain and Strain Rate on Dynamic Grain Growth and Subgrain Evolution During Plastic Deformation of an Interstitial-Free Steel at 850 ° C

Here, the effects of strain and strain rate on dynamic grain growth (DGG) and subgrain evolution are reported for an interstitial-free steel deformed at 850 ° C. Microstructures produced during tension tests at true-strain rates of 10 -4 and to 10 -3 s -1 true strains ranging from 0.02 to 0.2 were preserved following deformation. These were characterized using electron backscatter diffraction (EBSD), including the application of spherical harmonic transform indexing to produce high-angular-resolution EBSD (HR-EBSD) data. HR-EBSD data resolved the small misorientation angles of subgrain boundaries while imaging much larger data fields than possible with previously available techniques. The resulting data confirmed that steady-state flow stress is inversely proportional to the average subgrain size and that subgrain boundary misorientation angle increases with strain. The following new observations are reported. The rate of DGG increased with respect to time but decreased with respect to strain as strain rate increased. This behavior is rationalized through a simple model using separate rate parameters for the effects of time and strain. Subgrain size was not constant during steady-state deformation, but decreased slowly with increasing strain. Subgrain size distributions and subgrain boundary misorientation angle distributions were measured, and both remained approximately log-normal during steady-state deformation. Subgrain evolution demonstrated no dependence on parent grain size, crystallographic orientation, or Taylor factor. These new data suggest that steady-state flow stress is more likely controlled by the dislocation density internal to subgrains than by the spacing between subgrain boundaries.

dynamic grain growth↗

Non-destructive identification of unknown minor phases in polycrystalline bulk alloys using three-dimensional X-ray diffraction

Minor phases make considerable contributions to the mechanical and physical properties of metals and alloys. Unfortunately, it is difficult to identify unknown minor phases in a bulk polycrystalline material using conventional metallographic methods. Here, a non-destructive method based on three-dimensional X-ray diffraction (3DXRD) is developed to solve this problem. Simulation results demonstrate that this method is simultaneously able to identify minor phase grains and reveal their positions, orientations and sizes within bulk alloys. According to systematic simulations, the 3DXRD method is practicable for an extensive sample set, including polycrystalline alloys with hexagonal, orthorhombic and cubic minor phases. Experiments were also conducted to confirm the simulation results. The results for a bulk sample of aluminum alloy AA6061 show that the crystal grains of an unexpected γ-Fe (austenite) phase can be identified, three-dimensionally and nondestructively. Therefore, we conclude that the 3DXRD method is a powerful tool for the identification of unknown minor phases in bulk alloys belonging to a variety of crystal systems. This method also has the potential to be used for in situ observations of the effects of minor phases on the crystallographic behaviors of alloys. - Highlights: •A method based on 3DXRD is developed for identification of unknown minor phase. •Grain position, orientation and size, is simultaneously acquired. •A systematic simulation demonstrated the applicability of the proposed method. •Experimental results on a AA6061 sample confirmed the practicability of the method.

36 MATERIALS SCIENCE↗

Creep cavitation bands control porosity and fluid flow in lower crustal shear zones

Shear zones channelize fluid flow in Earth’s crust. However, little is known about deep crustal fluid migration and how fluids are channelized and distributed in a deforming lower crustal shear zone. This study investigates the deformation mechanisms, fluid-rock interaction, and development of porosity in a monzonite ultramylonite from Lofoten, northern Norway. The rock was deformed and transformed into an ultramylonite under lower crustal conditions (temperature = 700–730 °C, pressure = 0.65–0.8 GPa). The ultramylonite consists of feldspathic layers and domains of amphibole + quartz + calcite, which result from hydration reactions of magmatic clinopyroxene. The average grain size in both domains is <25 mm. Microstructural observations and electron backscatter diffraction analysis are consistent with diffusion creep as the dominant deformation mechanism in both domains. Festoons of isolated quartz grains define C'-type bands in feldspathic layers. These quartz grains do not show a crystallographic preferred orientation. The alignment of quartz grains is parallel to the preferred elongation of pores in the ultramylonites, as evidenced from synchrotron X-ray microtomography. Such C'-type bands are interpreted as creep cavitation bands resulting from diffusion creep deformation associated with grain boundary sliding. Mass-balance calculation indicates a 2% volume increase during the protolith-ultramylonite transformation, which is consistent with synkinematic formation of creep cavities producing dilatancy. Thus, this study presents evidence that creep cavitation bands may control deep crustal porosity and fluid flow. Nucleation of new phases in creep cavitation bands inhibits grain growth and enhances the activity of grain size–sensitive creep, thereby stabilizing strain localization in the polymineralic ultramylonites.

CENTRAL ALPS↗

Grain boundary resistance to fatigue crack growth

Results of an experimental study tracing the grain boundary effect on the fatigue crack growth rate are reported. Direct experimental evidence for the grain boundary blockage mechanism is presented. The orientation difference between two neighboring grains directly contributed to the extent of crack growth retardation.

Chen, QI↗

Characterization of Nb films for superconducting qubits using phase boundary measurements

Continued advances in superconducting qubit performance require more detailed understandings of the many sources of decoherence. Within these devices, two-level systems arise due to defects, interfaces, and grain boundaries and are thought to be a major source of qubit decoherence at millikelvin temperatures. In addition to Al, Nb is a commonly used metallization layer in superconducting qubits. Consequently, a significant effort is required to develop and qualify processes that mitigate defects in Nb films. As the fabrication of complete superconducting qubits and their characterization at millikelvin temperatures is a time and resource intensive process, it is desirable to have measurement tools that can rapidly characterize the properties of films and evaluate different treatments. Here, we show that measurements of the variation of the superconducting critical temperature T c with an applied external magnetic field H (of the phase boundary T c – H⁠) performed with very high-resolution show features that are directly correlated with the structure of the Nb films. In combination with x-ray diffraction measurements, we show that one can even distinguish variations in the size and crystal orientation of the grains in a Nb film by small but reproducible changes in the measured superconducting phase boundary.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Study of grain boundary transparency in(Yb$_{1-x}$Ca$_x$)Ba$_2$Cu$_3$O bicrystal thin films over a wide temperature, field, and field orientation range

The residual low angle grain boundary (GB) network is still the most important current-limiting mechanism operating in bi-axially textured rare earth barium copper oxide (REBCO) coated conductors. While Ca-doping is well established to improve super-current flow across low angle GBs in weak fields at high temperatures, Ca-doping also depresses T c , making it so far impractical for high temperature applications of REBCO coated conductors. On the other hand, high field magnet applications of REBCO require low temperatures. Here we systematically evaluate the effectiveness of Ca-doping in improving the GB transparency, r GB = J c GB /J c grain , of low angle Yb 1-x Ca x BaCuO [001] tilt bi-crystal films down to 10K and with magnetic fields perpendicular and parallel to the film surfaces, while varying the Ca and oxygen doping level. Using Low Temperature Scanning Laser Microscopy (LTSLM) and Magneto-Optical Imaging (MOI), we found r GB to strongly depend on the angle between magnetic field and the GB plane and clearly identified regimes in which J c GB can exceed J c grain (rGB>1) where the GB pinning is optimized by the field being parallel to the GB dislocations. However, even in this favorable situation, we found that r GB became much smaller at lower temperatures. Calculations of the GB Ca segregation profile predict that the high J c channels between the GB dislocation cores are almost Ca-free. It may be therefore that the positive effects of Ca doping seen by many authors near T c are partly a consequence of the higher Tc of these Ca-free channels.

Li, Pei↗

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗

Low-temperature oriented growth of vanadium dioxide films on CoCrTa metal template on Si and vertical metal-insulator transition

The authors achieved oriented growth of vanadium dioxide (VO{sub 2}) films on CoCrTa metal template grown on an Si substrate. Low-temperature ({approx}250 Degree-Sign C) deposition of VO{sub 2} films using inductively coupled-plasma-assisted sputtering technique realized an abrupt interface between VO{sub 2} and CoCrTa layers, suppressing the oxidation and diffusion of metal components. The films revealed a metal-insulator transition with resistance change of over 2 orders of magnitude. The CoCrTa film, in which Co hexagonal crystalline grains with c-axis orientation were surrounded by segregated Cr and Ta, serves for the oriented growth of VO{sub 2} crystalline film, enabling higher orders of transition in resistance and low voltage switching, even for the vertical (out-of-plane) direction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Adjoint-based optimization of mechanical performance in polycrystalline materials and structures through texture control

The texture of a polycrystalline material refers to the preferred orientation of the grains within the material. In metallic materials, texture can significantly affect the mechanical properties such as elastic moduli, yield stress, strain hardening, and fracture toughness. Recent advances in additive manufacturing of metallic materials offer the possibility in the not too distant future of controlling the spatial variation of texture. In this work, we investigate the advantages, in terms of mechanical performance, of allowing the texture to vary spatially. We use an adjoint-based gradient optimization algorithm within a finite element solver (COMSOL) to optimize several engineering quantities of interest in a simple structure (hole in a plate) and loading (uniaxial tension) condition. As a first step to general texture optimization, we consider the idealized case of a pure fiber texture in which the homogenized properties are transversely isotropic. In this special case, the only spatially varying design variables are the three Euler angles that prescribe the orientation of the homogenized material at each point within the structure. This work paves a new way to design metallic materials for tunable mechanical properties at the microstructure level.

36 MATERIALS SCIENCE↗

Comparative study of ITO and TiN fabricated by low-temperature RF biased sputtering

Radio frequency (RF) biasing induced by a second plasma source at the substrate is applied to low-temperature sputtering processes for indium tin oxide (ITO) and titanium nitride (TiN) thin films. Investigations on crystal structure and surface morphology show that RF-biased substrate plasma processes result in a changed growth regime with different grain sizes and orientations than those produced by processes without a substrate bias. The influence of the RF bias is shown comparatively for reactive RF-sputtered ITO and reactive direct-current-sputtered TiN. The ITO layers exhibit an improved electrical resistivity of 0.5 mΩ cm and an optical absorption coefficient of 0.5 × 10{sup 4 }cm{sup −1} without substrate heating. Room-temperature sputtered TiN layers are deposited that possess a resistivity (0.1 mΩ cm) of 3 orders of magnitude lower than, and a density (5.4 g/cm{sup 3}) up to 45% greater than, those obtained from layers grown using the standard process without a substrate plasma.

36 MATERIALS SCIENCE↗

Quantized Grain Boundary States Promote Nanoparticle Alignment During Imperfect Oriented Attachment

Oriented attachment (OA) has become a well-recognized mechanism for the growth of metal, ceramic, and biomineral crystals. While many computational and experimental studies of OA have shown that particles can attach with some misorientation then rotate to remove adjoining grain boundaries, the underlying atomistic pathways for this “Imperfect OA” process remain the subject of debate. In this paper, molecular dynamics and in situ TEM were used to probe the crystallographic evolution of up to 30 gold and copper nanoparticles during aggregation. It was found that Imperfect OA occurs because (1) grain boundaries become quantized when their size is comparable to the separation between constituent dislocations and (2) kinetic barriers associated with the glide of grain boundary dislocations are small. In support of these findings, TEM experiments show the formation of a single crystal aggregate after annealing 9 initially misoriented, agglomerated particles with evidence of dislocation slip and twin formation during particle/grain alignment. These observations motivate future work on assembled nanocrystals with tailored defects and call for a revision of Read-Shockley models for grain boundary energies in nanocrystalline materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantifying Equiaxed vs Epitaxial Solidification in Laser Melting of CMSX-4 Single Crystal Superalloy

The competition between epitaxial vs. equiaxed solidification has been investigated in CMSX-4 single crystal superalloy during laser melting as practiced in additive manufacturing. Single-track laser scans were performed on a powder-free surface of directionally solidified CMSX-4 alloy with several combinations of laser power and scanning velocity. Electron backscattered diffraction (EBSD) mapping facilitated identification of new orientations, i.e., “stray grains” that nucleated within the fusion zone along with their area fraction and spatial distribution. Using high-fidelity computational fluid dynamics simulations, both the temperature and fluid velocity fields within the melt pool were estimated. This information was combined with a nucleation model to determine locations where nucleation has the highest probability to occur in melt pools. In conformance with general experience in metals additive manufacturing, the as-solidified microstructure of the laser-melted tracks is dominated by epitaxial grain growth; nevertheless, stray grains were evident in elongated melt pools. It was found that, though a higher laser scanning velocity and lower power are generally helpful in the reduction of stray grains, the combination of a stable keyhole and minimal fluid velocity further mitigates stray grains in laser single tracks.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Ni-based Superalloy K418 Produced by the Continuous Unidirectional Solidification Process

Adopting effective strategies to control the solidification structure of Ni-based superalloys is a very interesting subject for metallurgists. Despite the achievement of developing and applying the continuous unidirectional solidification process in simple alloys, the utilization of this process for K418 alloys has been ignored. The microstructure and mechanical properties of a K418 alloy ingot produced by the continuous unidirectional solidification process were investigated. We found that the γ dendrites were typically cross-shaped in the transverse section. The orientation of surviving grains along the casting direction was <001> during competitive growth. The secondary dendrite arm spacing was 32.3 ± 2.5 μm at a cooling rate of 1.75 ± 0.35 °C/s from the surface to the center of the K418 alloy ingot. Due to the higher cooling rate than that of the conventional casting process, a more uniform microstructure and finer γ′ precipitation were obtained in the ingot. Thus, compared with the conventional casting, the tensile strength and the elongation are increased by 8.4 and 21.3%, respectively, at 25 °C. The tensile strength and elongation increased by 15.2 and 49.3%, respectively, at 800 °C. In addition, the fracture surfaces exhibited numerous typical dimples and dendritic fracture characteristics.

36 MATERIALS SCIENCE↗

Direct numerical simulations in solid mechanics for quantifying the macroscale effects of microstructure and material model-form error

Two fundamental approximations in macroscale solid-mechanics modeling are (1) the assumption of scale separation in homogenization theory and (2) the use of a macroscopic plasticity material model that represents, in a mean sense, the multitude of inelastic processes occurring at the microscale. With the goal of quantifying the errors induced by these approximations on engineering quantities of interest, we perform a set of direct numerical simulations (DNS) in which polycrystalline microstructures are embedded throughout a macroscale structure. The largest simulations model over 50,000 grains. The microstructure is idealized using a randomly close-packed Voronoi tessellation in which each polyhedral Voronoi cell represents a grain. An face centered cubic crystal-plasticity model is used to model the mechanical response of each grain. The overall grain structure is equiaxed, and each grain is randomly oriented with no overall texture. The detailed results from the DNS simulations are compared to results obtained from conventional macroscale simulations that use homogeneous isotropic plasticity models. The macroscale plasticity models are calibrated using a representative volume element of the idealized microstructure. Furthermore, we envision that DNS modeling will be used to gain new insights into the mechanics of material deformation and failure.

36 MATERIALS SCIENCE↗

Shock Response of Commercial Purity Polycrystalline Magnesium Under Uniaxial Strain at Elevated Temperatures

Here, results of plate impact experiments designed to investigate the onset of incipient plasticity in commercial purity polycrystalline magnesium (99.9%) under weak uniaxial strain compression and elevated temperatures up to melt are presented. The dynamic stress at yield and post yield of magnesium, as inferred from the measured normal component of the particle velocity histories at the free (rear) surface of the target plate, are observed to decrease progressively with increasing test temperatures in the range from 23 to 500 °C. At (higher) test temperatures in the range 500–610 °C, the rate of decrease of dynamic stress with temperature at yield and post-yield in the sample is observed to weaken. At still higher test temperatures (617 and 630 °C), a dramatic increase in dynamic yield as well as flow stress is observed indicating a change in dominant mechanism of plastic deformation as the sample approaches the melt point of magnesium at strain rates of ~105/s. In addition to these measurements at the wavefront, the plateau region of the free surface particle velocity profiles indicates that the longitudinal (plastic) impedance of the magnesium samples decreases continuously as the sample temperatures are increased from room to 610 °C, and then reverses trend (indicating increasing material longitudinal impedance/ strength) as the sample temperatures are increased to 617 and 630 °C. Lastly, electron back scattered diffraction analysis of the as-received and annealed pre-test magnesium samples reveal grain coarsening as well as grain re-orientation to a different texture during the heating process of the samples.

36 MATERIALS SCIENCE↗

Structure of Cr Film Epitaxially Grown on MgO (001)

Cr(001) films of thickness ~100 nm were epitaxially grown on MgO (001) using molecular beam epitaxy at both room temperature and 550 °C. The structure of the films was characterized using high resolution transmission electron microscopy, electron diffraction, and electron energy-loss spectroscopy. Room temperature growth leads to highly oriented columnar structured grains in the film, while growth at 550 °C yields high quality single crystal Cr film, possessing a 45 degree rotational epitaxial relationship between the film and the substrate. For the single crystal film, the interface exhibited coherent regions separated by equally-spaced misfit dislocations. When imaged from the MgO[100]//Cr[110] direction, the dislocation spacing is 5.38 nm and 4.64 nm for the films grown at room temperature and 550 °C, respectively, which is slightly smaller than the expected value of 6.25 nm calculated from the differences in lattice spacing based on known lattice constants. The results presented here indicate that the lattice mismatch between the film and the substrate is accommodated mainly by interface misfit dislocations above some critical thickness. The electronic structure of the interface between the film and the substrate is also explored using electron energy-loss spectroscopy.

(001)↗