Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Processing and Mechanical Properties of Various Zirconia/Alumina Composites for Fuel Cell Applications

Various electrolyte materials for solid oxide fuel cells were fabricated by hot pressing 10 mol% yttria-stabilized zirconia (10-YSZ) reinforced with two different forms of alumina, particulates and platelets, each containing 0 to 30 mol% alumina. Flexure strength and fracture toughness of both particulate and platelet composites at ambient temperature increased with increasing alumina content, reaching a maximum at 30 mot% alumina. For a given alumina content, strength of particulate composites was greater than that of platelet composites, whereas, the difference in fracture toughness between the two composite systems was negligible. No virtual difference in elastic modulus and density was observed for a given alumina content between particulate and platelet composites. Thermal cycling up to 10 cycles between 200 to 1000 C did not show any effect on strength degradation of the 30 mol% platelet composites, indicative of negligible influence of CTE mismatches between YSZ matrix and alumina grains.

Choi, Sung R.↗
NASA NTRS2005

Solid Oxide Fuel Cell Seal Glass - BN Nanotubes Composites

Solid oxide fuel cell seal glass G18 composites reinforced with approx.4 weight percent of BN nanotubes were fabricated via hot pressing. Room temperature strength and fracture toughness of the composite were determined by four-point flexure and single edge V-notch beam methods, respectively. The strength and fracture toughness of the composite were higher by as much as 90% and 35%, respectively, than those of the glass G18. Microscopic examination of the composite fracture surfaces using SEM and TEM showed pullout of the BN nanotubes, similar in feature to fiber-reinforced ceramic matrix composites with weak interfaces. Other mechanical and physical properties of the composite will also be presented.

Bansal, Narottam P.↗
DOE OSTI2021

FCET Solid Oxide Fuel Cell Testing and Development: CRADA 526 [Abstract only]

The purpose of the proposed project is for PNNL to test the performance of prototype solid oxide fuel cells (SOFCs) created by FCET. Such testing will provide FCET with independent performance data that can be communicated to potential clients and/or investors. Additionally, PNNL will collaborate with FCET on design changes to improve fuel cell performance. Intellectual property developed in this way will benefit FCET with improved products to market, and PNNL through royalty revenue. The key technology held by FCET is a process to deposit extremely thin layers of oxide materials, from 10-50 nm in thickness. The range of possible materials that can be deposited with their method is broad, but this project will focus on the yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight YSZ membranes have been a long-sought target in SOFC research. The thinner the YSZ, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). 10-50 nm would be a major step change in YSZ thickness from the state of the art. PNNL can team with FCET on future R&D projects and push this technology forward to improve energy efficiency and reduce carbon emissions.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1993

A High Performance H2-Cl2 Fuel Cell for Space Power Applications

NASA has numerous airborne/spaceborne applications for which high power and energy density power sources are needed. The proton exchange membrane fuel cell (PEMFC) is an attractive candidate for such a power source. PEMFC's offer many advantages for airborne/spaceborne applications. They have high power and energy densities, convert fuel to electrical power with high efficiency at both part and full load, and can rapidly startup and shutdown. In addition, PEMFC's are lightweight and operate silently. A significant impediment to the attainment of very high power and energy densities by PEMFC's is their current exclusive reliance on oxygen as the oxidant. Conventional PEMFC's oxidize hydrogen at the anode and reduce oxygen at the cathode. The electrode kinetics of oxygen reduction are known to be highly irreversible, incurring large overpotential losses. In addition, the modest open circuit potential of 1.2V for the H2-O2 fuel cell is unattainable due to mixed potential effects at the oxygen electrode. Because of the high overpotential losses, cells using H2 and O2 are capable of achieving high current densities only at very low cell voltages, greatly curtailing their power output. Based on experimental work on chlorine reduction in a gas diffusion electrode, we believe significant increases in both the energy and power densities of PEMFC systems can be achieved by employing chlorine as an alternative oxidant.

Anderson, Everett B.↗
NASA NTRS1983

Systems analysis of electricity production from coal using fuel cells

Gasifiers, heat transfer, gas stability, quench, water-gas shift reaction, reforming-methanation, other catalytic reactions, compressors and expanders, acid-gas removal, the fuel cell, and catalytic combustors are described. System pressure drops, efficiency of rotating power equipment, heat exchangers, chemical reactions, steam systems, and the fuel cell subsystems are discussed.

Fleming, D. K.↗
DOE OSTI2021

Promoting Atomically Dispersed MnN 4 Sites via Sulfur Doping for Oxygen Reduction: Unveiling Intrinsic Activity and Degradation in Fuel Cells

Carbon supported and nitrogen coordinated single Mn site catalysts (Mn-N-C) catalysts are the most desirable platinum group metal (PGM)-free cathode catalysts for proton exchange membrane fuel cells (PEMFCs) due to their insignificant Fenton reactions (vs. Fe), earth abundances (vs. Co) and encouraging activity and stability. However, current Mn-N-C catalysts suffer from high over-potential due to low intrinsic activity and less dense MnN 4 sites. Herein, we present sulfur-doped Mn-N-C catalyst (Mn-N-C-S) synthesized through an effective adsorption-pyrolysis process. Using electron microscopy and X-ray absorption spectroscopy (XAS) techniques, we verify the uniform dispersion of MnN 4 sites and confirm the effect of S doping on the Mn-N coordination. The Mn-N-C-S catalyst exhibits a favorable oxygen reduction reaction (ORR) activity in acidic media relative to the S-free Mn-N-C catalyst. The corresponding membrane electrode assembly (MEA) generated a remarkable performance with a peak power density of 500 mW cm -2 under a realistic H 2 /air environment. The constant voltage tests of fuel cells confirm the much-enhanced stability of the Mn-N-C-S catalyst compared to the Fe-N-C and Fe-N-C-S catalysts. The electron microscopy and Fourier transform XAS analysis provide insights into catalyst degradation associated with Mn oxidation and agglomeration. The theoretical calculation elucidates that the promoted ORR activity is mainly attributed to the spatial effect stemmed from the repulsive interaction between the ORR intermediates and adjacent S do-pants.

25 ENERGY STORAGE↗
NASA NTRS1989

Regenerative fuel cell systems for project pathfinder

The objectives of a surface power program, an element of the exploration thrust of the Pathfinder project, and plans for meeting them are outlined. Technological assessment and tradeoff studies of fuel cell and electrolyzer technologies suitable for use in a regenerative fuel cell are described. The viability of proton exchange membranes (PEM) in meeting the system requirements is discussed.

Huff, J. R.↗
DOE OSTI2020

All-Sputtered, Superior Power Density Thin-Film Solid Oxide Fuel Cells with a Novel Nanofibrous Ceramic Cathode

Thin film solid oxide fuel cells (TF-SOFCs) are attracting attention due to their ability to operate at comparatively lower temperatures (400–650 °C) that are unattainable for conventional anode-supported SOFCs (650–800 °C). However, limited cathode performance and cell scalability remain persistent issues. Here, we report a new approach of fabricating yttria-stabilized zirconia (YSZ)-based TF-SOFCs via a scalable magnetron sputtering process. Notable is the development and deposition of a porous La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 2.95 (LSCF)-based cathode with a unique fibrous nanostructure. This all-sputtered cell shows an open-circuit voltage of ~1.0 V and peak power densities of ~1.7 and ~2.5 W/cm 2 at 600 and 650 °C, respectively, under hydrogen fuel and air along with showing stable performance in short-term testing. The power densities obtained in this work are the highest among YSZ-based SOFCs at these low temperatures, which demonstrate the feasibility of fabricating exceptionally high-performance TF-SOFC cells with distinctive dense or porous nanostructures for each layer, as desired, by a sputtering process. This work illustrates a new, potentially low-cost, and scalable platform for the fabrication of next-generation TF-SOFCs with excellent power output and stability.

25 ENERGY STORAGE↗
DOE OSTI2022

Surface Regulating of a Double–Perovskite Electrode for Protonic Ceramic Fuel Cells to Enhance Oxygen Reduction Activity and Contaminants Poisoning Tolerance

Protonic ceramic fuel cells (PCFCs) are one of the most efficient energy conversion devices. However, the performance of current PCFCs is greatly limited by the sluggish oxygen reduction reaction (ORR) kinetics and the fast degradation of cathode due to contaminants poisoning (such as Cr species and steam). In this work, we report a surface regulating of a double perovskite PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O 5+δ (PBSCF) cathode by a Pr 0.9 Fe 0.7 Co 0.3 O 3 (PFC) catalyst coating to enhance the ORR activity and stability. When tested in direct contact with Cr in the air with 3% H 2 O at 650 °C, the polarization resistance (Rp) of the PFC-PBSCF electrode increases from $\approx$0.39 to 0.45 Ω cm 2 after 100 h operation; in contrast, the R p of a PBSCF electrode increases from 0.63 to 0.82 Ω cm 2 . Further, a PCFC with the PFC-PBSCF cathode demonstrates an excellent peak power density ($\approx$1.08 W cm -2 at 650 °C) and significantly enhanced durability (degradation rate of 0.03 % h -1 ), much better than those of the cells with a PBSCF cathode ($\approx$0.75 W cm -2 and degradation rate of 0.12 % h -1 ). Raman spectroscopy and density functional theory calculations indicate that the PFC catalyst coating diminishes the formation of Cr species, such as (Ba 1-x Sr x )CrO 4 , on the cathode surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-Performance Pt–Co Nanoframes for Fuel-Cell Electrocatalysis

Pt-based alloy catalysts are promising candidates for fuel-cell applications, especially for cathodic oxygen reduction reaction (ORR) and anodic methanol oxidation reaction (MOR). The rational design of composition and morphology is crucial to promoting catalytic performances. Here, we report the synthesis of Pt–Co nanoframes via chemical etching of Co from solid rhombic dodecahedra. The obtained Pt–Co nanoframes exhibit excellent ORR mass activity in acidic electrolyte, which is as high as 0.40 A mg Pt –1 initially and 0.34 A mg Pt –1 after 10 000 potential cycles at 0.95 V RHE . Furthermore, their MOR mass activity in alkaline media is up to 4.28 A mg Pt –1 and is 4-fold higher than that of commercial Pt/C catalyst. Furthermore, experimental studies indicate that the weakened binding of intermediate carbonaceous poison contributes to the enhanced MOR behavior. More impressively, the Pt–Co nanoframes also demonstrate remarkable stability under long-term testing, which could be attributed to the negligible electrochemical Co dissolution.

25 ENERGY STORAGE↗