Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Study of a High Voltage Ion Engine Power Supply

A complete laboratory breadboard version of a ion engine power converter was built and tested. This prototype operated on a line voltage of 80-120 Vdc, and provided output ratings of 1100 V at 1.8 kW, and 250 V at 20 mA. The high-voltage (HV) output voltage rating was revised from the original value of 1350 V at the beginning of the project. The LV output was designed to hold up during a 1-A surge current lasting up to 1 second. The prototype power converter included a internal housekeeping power supply which also operated from the line input. The power consumed in housekeeping was included in the overall energy budget presented for the ion engine converter. HV and LV output voltage setpoints were commanded through potentiometers. The HV converter itself reached its highest power efficiency of slightly over 93% at low line and maximum output. This would dip below 90% at high line. The no-load (rated output voltages, zero load current) power consumption of the entire system was less than 13 W. A careful loss breakdown shows that converter losses are predominately Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) conduction losses and HV rectifier snubbing losses, with the rectifier snubbing losses becoming predominant at high line. This suggests that further improvements in power efficiency could best be obtained by either developing a rectifier that was adequately protected against voltage overshoot with less snubbing, or by developing a pre-regulator to reduced the range of line voltage on the converter. The transient testing showed the converter to be fully protected against load faults, including a direct short-circuit from the HV output to the LV output terminals. Two currents sensors were used: one to directly detect any core ratcheting on the output transformer and re-initiate a soft start, and the other to directly detect a load fault and quickly shut down the converter for load protection. The finished converter has been extensively fault tested without failure. The finished converter has been packaged suitable for use as a laboratory prototype for further testing. The finished converter is readily transportable. An article on design issues for high voltage converters for ion engines is included as an attachement.

Stuart, Thomas A.↗
NASA NTRS1997

Investigation of an Aberrant Cell Voltage During the Filling of a Large Lithium Thionyl Chloride Cell

The investigation of an aberrant cell voltage during the filling of a large lithium thionyl chloride cell summary is at: an aberrant voltage trace was noted during the review of cell filling data; incident was traced to an interruption during filling; experimentation suggested oxidizable sites within the carbon electrode were responsible for the drop in voltage; the voltage anomaly could be reproduced by interrupting the filling of similar cells; and anomalous voltage dip was not due to a short.

Thaller, Lawrence H.↗
NASA NTRS1995

The circum-Chryse region as a possible example of a hydrologic cycle on Mars: Geologic observations and theoretical evaluation

The transection and superposition relationships among channels, chaos, surface materials units, and other features in the circum-Chryse region of Mars were used to evaluate relative age relationships and evolution of flood events. Channels and chaos in contact (with one another) were treated as single discrete flood-carved systems. Some outflow channel systems form networks and are inferred to have been created by multiple flood events. Within some outflow channel networks, several separate individual channel systems can be traced to a specific chaos which acted as flood-source area to that specific flood channel. Individual flood-carved systems were related to widespread materials units or other surface features that served as stratigraphic horizons. Chryse outflow channels are inferred to have formed over most of the perceivable history of Mars. Outflow channels are inferred to become younger with increasing proximity to the Chryse basin. In addition, outflow channels closer to the basin show a greater diversity in age. The relationship of subsequent outflow channel sources to the sources of earlier floods is inferred to disfavor episodic flooding due to the progressive tapping of a juvenile near-surface water supply. Instead, we propose the circum-Chryse region as a candidate site of past hydrological recycling. The discharge rates necessary to carve the circum-Chryse outflow channels would have inevitably formed temporary standing bodies of H2O on the Martian surface where the flood-waters stagnated and pooled (the Chryse basin is topographically enclosed). These observations and inferences have led us to formulate and evaluate two hypotheses: (1) large amounts of the sublimated H2O off the Chryse basin flood lakes precipitated (snowed) onto the flood-source highlands and this H2O was incorporated into the near surface, recharging the H2O sources, making possible subsequent deluges; and (2) ponded flood-water in Chryse basin drained back down an anti basinward dipping subsurface layer accessed along the southern edge of the lake, recharging the flood-source aquifers. H2O not redeposited in the flood-source region was largely lost to the hydrologic cycle. This loss progressively lowered the vitality of the cycle, probably by now killing it. Our numerical evaluations indicate that of the two hypotheses we formulated, the groundwater seep cycle seems by far the more viable. Optimally, approx. 3/4 of the original mass of an ice-covered cylindrical lake (albedo 0.5, 1 km deep, 100-km radius, draining along its rim for one quarter of its circumference into substrata with a permeability of 3000 darcies) can be modeled to have moved underground (on timescales of the order of 10(exp 3) years) before the competing mechanisms of sublimation and freeze down choked off further water removal. Once underground, this water can travel distances equal to the separation between Chryse basin and flood-source sites in geologically short (approx. 10(exp 6) year-scale) times. Conversely, we calculate that optimally only approx. 40% of the H2O carried from Chryse can condense at the highlands, and most of the precipitate would either collect at the base of the highlands/lowlands scarp or sublimate at rates greater than it would accumulate over the flood-source sites. Further observations from forthcoming missions may permit the determination of which mechanisms may have operated to recycle the Chryse flood-waters.

Moore, Jeffrey M.↗
NASA NTRS1998

Rapid Prototyping of Composite Structures

This progress report for the project Rapid Production of Composite Structures covers the period from July 14, 1997 to June 30, 1998. It will present a short overview of the project, followed by the results to date and plans for the future. The goal of this research is to provide a minimum 100x reduction in the time required to produce arbitrary, laminated products without the need for a separate mold or an autoclave. It will accomplish this by developing the science underlying the rapid production of composite structures, specifically those of carbon fiber-epoxy materials. This scientific understanding will be reduced to practice in a demonstration device that will produce a part on the order of 12" by 12" by 6". Work in the past year has focussed on developing an understanding of the materials issues and of the machine design issues. Our initial goal was to use UV cureable resins to accomplish full cure on the machine. Therefore, we have centered our materials work around whether or not UV cureable resins will work. Currently, the answer seems to be that they will not work, because UV light cannot penetrate the carbon fibers, and because no "shadow" curing seems to occur. As a result, non-UV cureable resins are being investigated. This has resulted in a change in the machine design focus. We are now looking into a "dip and place" machine design, whereby a prepreg layer would have one side coated with a curing agent, and then would be placed onto the previous layer. This would lead to cure at the interface, but not to the top of the layer. The formulation of the resins to accomplish this task at room or slightly elevated temperatures is being investigated, as is the machine design needed to apply the curing agent and then cure or partially cure the part. A final, out-of-autoclave, post-cure may be needed with this strategy, as final cure on the machine may not be possible, as it was for the initial UV cure strategy. The remainder of this report details the progress in the materials and machine design areas. Materials Development The material system must be designed to fulfill the following requirements: to reduce the time and labor requirements of typical cure cycles; to reduce the thermal stresses developed during conventional heat curing; and to develop a structure that the build sequence requires. In order to accomplish these goals, there have been parallel tracks of investigation. One area has tested photopolymerizable (ultraviolet (UV) curable) materials and combinations of these materials with standard heat curing resins. The second area has investigated resins that cure rapidly at room or low heat temperatures. The main goal of these investigations has been to identify a system that will rapidly set or cure at room temperature during a tape lay-up process and hold its structure during a post-cure cycle.

Colton, Jonathan S.↗
NASA NTRS1997

Global MHD Magnetospheric Simulation of January 10, 1997 Encounter with Magnetic Cloud

We present a global MHD magnetospheric simulation of the encounter of the magnetic cloud with the terrestrial magnetosphere on January 10-11, 1997. The MHD simulation is driven by IMF and solar wind plasma measurements provided by Wind situated about 100 $R_E$ upstream from Earth. Field-aligned currents produced in the model are mapped down to the ionosphere and are directly compared to auroral images from the Polar UVI. Particular attention will be paid to the interval following the the initial shock wave arrival (around 0100 UT on the 1Oth) but preceding the passage of the magnetic cloud proper (commencing at about 0430 UT) for which there was continuous viewing of the entire auroral oval from apogee by Polar. This turbulent period is characterized by numerous dynamic pressure rises and dips and several northward and southward turnings of the IMF, all of which generate dynamic activity in the simulation that is reflected in the mapped field-aligned current patterns. As discussed by Brittnacher et al. in this session, the auroral morphology imaged by UVI during this period includes: shock wave-induced brightening of the oval followed by a pseudo-onset near midnight, several sun-aligned and curled arcs within the polar cap, an expanding polar cap cleared of arcs, and finally substorm onset at 0337 UT. These features will be directly compared to region 1 and 2 current systems as well as cusp currents in the simulation. Spacecraft magnetopause crossings are also predicted by the global simulation and will be compared to observed crossings, including numerous dayside crossings by Geotail on the 1Oth, and geosynchronous crossings early on January 11.

Elsen, R.↗
NASA NTRS1998

Crystal Growth of Mixed Optical Materials With the Automatic Czochralski Puller

Most of optical and semiconductor single crystalline materials produced in the electronic industry is grown with the Czochralski technique. This is the only technique capable of producing large high quality single crystals in a reasonable amount of time. The technique originated, and took its name, from pioneering work by Polish engineer J. Czochralski in 1917, who pulled single crystal wires (fibers) of low melting point metals from the melt in order to determine the maximum speeds at which they could be crystallized. The technique has been modified and its application has been extended first to the growth of silicon and later to a very wide range of compound semiconductors, metals, oxides and halides. It is now the dominant technique for the wide range of materials in the electronic industries. Czochralski growth is initiated by dipping a seed crystal of a chosen crystallographic orientation onto the surface of a melt contained in the heated crucible. The seed is then slowly withdrawn, solidifying the adherent column of the melt in steady state at an average rate given by the sum of the pulling rate and the rate of lowering the solid-liquid interface due to the depletion of the melt in the crucible. The control of the desired crystal diameter is achieved by closely controlling the heat balance at the solid-liquid interface.

Loutts, George B.↗
NASA NTRS1998

Variable-Frequency QPOs from the Galactic Microquasar GRS 1915+105

We show that the galactic microquasar GRS 1915+105 exhibits quasi-periodic oscillations (QPOS) whose frequency varies continuously from 1-15 Hz, during spectrally hard dips when the source is in a flaring state. NN'e report here analyses of simultaneous energy spectra and power density spectra at 4 s intervals. The energy spectrum is well fit at each time step by an optically thick accretion disk plus power law model, while the power density spectrum consists of a varying red noise component plus the variable frequency QPO. The features of both spectra are strongly correlated with one another. The 1-15 Hz QPOs appear when the power law component becomes hard and intense, and themselves have an energy spectrum consistent with the power law component (with root mean square amplitudes as high as 10%). The frequency of the oscillations, however, is most strikingly correlated with the parameters of the thermal disk component. The tightest correlation is between QPO frequency and the disk X-ray flux. This fact indicates that the properties of the QPO are not determined by solely a disk or solely a corona.

Markwardt, Craig B.↗
NASA NTRS1998

Rapid Prototyping of Composite Structures

This final report for the project Rapid Production of Composite Structures covers the period from July 14, 1997 to September 30, 1998. It will present a short overview of the project, followed by the results to date and plans for the future. The goal of this research is to provide a minimum 100x reduction in the time required to produce arbitrary, laminated products without the need for a separate mold or an autoclave. It will accomplish this by developing the science underlying the rapid production of composite structures, specifically those of carbon fiber-epoxy materials. This scientific understanding will be reduced to practice in a demonstration device that will produce a part on the order of 12in. by 12in. by 6in. Work in the past year has focussed on developing an understanding of the materials issues and of the machine design issues. Our initial goal was to use UV cureable resins to accomplish full cure on the machine. Therefore, we have centered our materials work around whether or not UV cureable resins will work. Currently, the answer seems to be that they will not work, because UV light cannot penetrate the carbon fibers, and because no "shadow" curing seems to occur. As a result, non-UV cureable resins are being investigated. This has resulted in a change in the machine design focus. We are now looking into a "dip and place" machine design, whereby a prepreg layer would have one side coated with a curing agent, and then would be placed onto the previous layer. This would lead to cure at the interface, but not to the top of the layer. The formulation of the resins to accomplish this task at room or slightly elevated temperatures is being investigated, as is the machine design needed to apply the curing agent and then cure or partially cure the part. A final, out-of-autoclave, post-cure may be needed with this strategy, as final cure on the machine may not be possible, as it was for the initial UV cure strategy. The remainder of this report details the progress in the materials and machine design areas.

Colton, Jonathan S.↗
NASA NTRS1998

Occurrence of Equatorial F Region Irregularities: Evidence for Tropospheric Seeding

We present a new gap-free version of the seasonal and longitudinal 0 (s/l) variations of P(sub EFI), the equatorial F region irregularity (EFI) occurrence probability, based on data from the AE-E spacecraft. The agreement of this and three earlier partial P(sub EFI) patterns verifies all four. We reinterpret another earlier gap-ridden pattern, that of D(bar)(sub RSF), a topside ionogram index of average darkening by range spread F. We compare it with P(sub EFI) and, using ionosonde radio science considerations, we conclude that D(bar)(sub RSF) = P(sub EFI) times a factor depending on the average number of topside plasma bubbles visible to the ionosonde. The s/l variations of D(baar)(sub RSF) thus imply s/l variations in the average spacing of bubbles, whose seeds have an occurrence probability pattern P(sub seed). For discussion we assume P(sub EFI) = P(sub inst)P(sub seed) is the pattern of F region instability. The P(sub EFI) pattern, which is by definition independent of seed and/or bubble spacing, is far too complex to be explained by the dominant paradigm, that of changes in P(sub inst) by simple changes in the F region altitude and/or north-south asymmetry. We examine evidence behind this dominance, and find it unconvincing. Both the asymmetry and sunset-node/altitude hypotheses of 1984 and 1985, respectively, seem to be partly based on misunderstood data, and their features appear displaced in time and space from those of our repeatable P(sub EFI) pattern. In contrast, if P(sub seed) variations influence the P(sub EFI) pattern and depend on thermospheric gravity waves from tropospheric convection near the dip equator, then the seasonal maxima (minima) Of P(sub EFI) could be explained, since they all occur above relatively warm (cold) surface features, where convection is maximal (minimal). Also, the hypothesis of the dominance of the P(sub seed) term could explain an unusual December/January P(sub EFI) maximum in the deep, wide, normal Pacific minimum in the one data set obtained in El Nino years. Based on the experiments we consider, we predict that the s/l variations Of P(sub seed) will be found to be similar to those of P(sub EFI) and largely to explain them. Finally, we find reasons, based on the similarity of the D(sub RSF) variations to s/l patterns of the average scintillation index, for not using, as is commonly done, such scintillation patterns as substitutes for P(sub EFI) or P(sub inst) patterns.

McClure, J. P.↗
NASA NTRS1999

Low Luminosity States of the Black Hole Candidate GX 339-4: Timing Analysis - 2

Here we present timing analysis of a set of eight Rossi X-ray Timing Explorer (RXTE) observations of the black hole candidate GX 339-4 that were taken during its hard/low state. On long time scales, the RXTE All Sky Monitor data reveal evidence of a 240 day periodicity, comparable to timescales expected from warped, precessing accretion disks. On short timescales all observations save one show evidence of a persistent f(qpo approximately equals 0.3 Hz quasi-periodic oscillations (QPO)). The broad band (10 (exp -3) to 10 (exp2) Hz) power appears to be dominated by two independent processes that can be modeled as very broad Lorentzians with Q approximately less than - 1. The coherence function between soft and hard photon variability shows that if these are truly independent processes, then they are individually coherent, but they are incoherent with one another. This is evidenced by the fact that the coherence function between the hard and soft variability is near unity between 5 x 10 (exp -3) but shows evidence of a dip at f approximately equals 1 Hz. This is the region of overlap between the broad Lorentzian fits to the Power Spectral Density (PSD). Similar to Cyg X-1, the coherence also drops dramatically at frequencies approximately greater than 1O Hz. Also similar to Cyg X-1, the hard photon variability is seen to lag the soft photon variability with the lag time increasing with decreasing Fourier frequency. The magnitude of this time lag appears to be positively correlated with the flux of GX 339-4. We discuss all of these observations in light of current theoretical models of both black hole spectra and temporal variability.

Nowak, Michael A.↗
NASA NTRS1999

Thermal Emission Spectroscopy of 1 Ceres: Evidence for Olivine

Thermal emission spectra of the largest asteroid 1 Ceres obtained from the Kuiper Airborne Observatory display features that may provide information on its surface mineralogy. A plot of the Ceres spectrum (calibrated using alpha Boo as a standard) divided by a standard thermal model (STM) is shown. Also shown is the emissivity spectrum deduced from reflectivity measurements for olivine grains <5 microns in diameter. The general shape of the Ceres and the olivine curves agree in essential details, such as the maxima from 8 to 12 microns, the minimum between 12 and 14 microns, the broad peak near 17.5 micron, and the slope beyond 22 micron. (Use of the 10 to 15-micron grain reflectivities provides a better match to the 12- to 14-micron dip. We used a value of unity for beta, the beaming factor associated with small-scale surface roughness in our STM. Adjustment of beta to a lower value raises the long-wavelength side of the Ceres spectrum, providing an even better match to the olivine curve.) The emissivity behavior roughly matches the emission coefficients which were calculated for olivine particles with a particle radius of 3 microns. Their calculations show not only the negative slope from 23 to 25 pm, but a continued decrease past 30 micron. The Ceres emissivity is thus similar to that of small olivine grains from 8 to 30 micron, but olivine's emissivity is lower from 5 to 8 pm.

Witteborn, F. C.↗
NASA NTRS1999

Some Peculiar Properties of Magnetic Clouds as Observed by the WIND Spacecraft

We aimed at understanding the common characteristics of magnetic clouds, relevant to solar-interplanetary connections, but exceptional ones were noted and are stressed here through a short compendium. The study is based on analyses of 28 good or better events (Out of 33 candidates) as identified in WIND magnetic field and plasma data. These cloud intervals are provided by WIND-MFI's Website under the URL (http://lepmfi.gsfc.nasa.gov/mfi/mag_cloud_publ.html#table). The period covered is from early 1995 to November 1998. A force free, cylindrically symmetric, magnetic field model has been applied to the field data in usually 1-hour averaged form for the cloud analyses. Some of the findings are: (1) one small duration event turned out to have an approximately normal size which was due to a distant almost "skimming" passage by the spacecraft; (2) One truly small event was observed, where 10 min averages had to be used in the model fitting; it had an excellent model fit and the usual properties of a magnetic cloud, except it possessed a small axial magnetic flux; (3) One cloud ha a dual axial-field-polarity, in the sense that the "core" had one polarity and the annular region around it had an opposite polarity. This event also satisfied the model and with a ve3ry good chi-squared value. Some others show a hint of this dual polarity; (4) The temporal distribution of occurrence clouds over the 4 years show a dip in 1996; (5) About 50 % of the clouds had upstream shocks; any others had upstream pressure pulses; (6) The overall average speed (390 km/s) of the best 28 events is less than the normally quoted for the average solar wind speed (420 km/s) The average of central cloud speed to the upstream solar wind speed was not much greater than one (1.08), even though many of these clouds were drivers of interplanetary shocks. Cloud expansion is partly the reason for the existence of upstream shocks; (7) The cloud axes often (about 50 % of the time) revealed reasonable attitudes with respect to the interpreted solar source, from simple geometry, but many bore no relationship, suggesting that their observations at 1 AU were probably those of the legs of the global cloud often having near-radial axes; (8) many clouds appear to have magnetic holes at or their their boundaries.

Berdichevsky, D.↗
NASA NTRS1995

The Circum-Chryse Region as a Possible Example of a Hydrologic Cycle on Mars: Geologic Observations and Theoretical Evaluation

The transection and superposition relationships among channels, chaos, surface materials units, and other features in the circum-Chryse region of Mars were used to evaluate relative age relationships and evolution of flood events. Channels and chaos in contact (with one another) were treated as single discrete flood-carved systems. Some outflow channel systems form networks and are inferred to have been created by multiple flood events. Within some outflow channel networks, several separate individual channel systems can be traced to a specific chaos which acted as flood-source area to that specific flood channel. Individual flood-carved systems were related to widespread materials units or other surface features that served as stratigraphic horizons. Chryse outflow channels are inferred to have formed over most of the perceivable history of Mars. Outflow channels are inferred to become younger with increasing proximity to the Chryse basin. In addition, outflow channels closer to the basin show a greater diversity in age. The relationship of subsequent outflow channel sources to the sources of earlier floods is inferred to disfavor episodic flooding due to the progressive tapping of a juvenile near-surface water supply. Instead, we propose the circum-Chryse region as a candidate site of past hydrological recycling. The discharge rates necessary to carve the circum-Chryse outflow channels would have inevitably formed temporary standing bodies of H2O on the Martian surface where the flood-waters stagnated and pooled (the Chryse basin is topographically enclosed). These observations and inferences have led us to formulate and evaluate two hypotheses: (1) large amounts of the sublimated H2O off the Chryse basin flood lakes precipitated (snowed) onto the flood-source highlands and this H2O was incorporated into the near surface, recharging the H2O sources, making possible subsequent deluges; and (2) ponded flood-water in Chryse basin drained back down an anti basinward dipping subsurface layer accessed along the southern edge of the lake, recharging the flood-source aquifers. H2O not redeposited in the flood-source region was largely lost to the hydrologic cycle. This loss progressively lowered the vitality of the cycle, probably by now killing it. Our numerical evaluations indicate that of the two hypotheses we formulated, the groundwater seep cycle seems by far the more viable. Optimally, approximately 3/4 of the original mass of an ice-covered cylindrical lake (albedo 0.5, 1 km deep, 100-km radius, draining along its rim for one quarter of its circumference into substrata with a permeability of 3000 darcies) can be modeled to have moved underground (on timescales of the order of 10(exp 3) years) before the competing mechanisms of sublimation and freeze down choked off further water removal. Once underground, this water can travel distances equal to the separation between Chryse basin and flood-source sites in geologically short (approximately 10(exp 6) year-scale) times. Conversely, we calculate that optimally only approximately 40% of the H2O carried from Chryse can condense at the highlands, and most of the precipitate would either collect at the base of the highlands/lowlands scrap or sublimate at rates greater than it would accumulate over the flood-source sites. Further observations from forthcoming missions may permit the determination of which mechanisms may have operated to recycle the Chryse flood-waters.

Moore, Jeffrey M.↗
NASA NTRS1999

The Dipper Satellite: A Medium-Class Explorer Mission to the Threshold of Space

The Dipper satellite will carry out an unprecedented, systematic, and focused in-situ exploration of the Earth's lower ionosphere and thermosphere below 200 km that will produce a pivotal base of knowledge that will significantly advance our understanding of knowledge that will significantly advance our understanding of how our near-space environment works. The satellite will carry comprehensive in-situ probes to measure vector electric and magnetic fields, plasma density and temperature, ion velocities, ion and neutral composition and winds, energetic particles including suprathermal electrons, gravity waves, and lightning bursts. The satellite will include a propulsion system and tapered body that will provide over 10,000 excursions to altitudes below 200 km with over 3000 dips to altitudes below 150 km. With this instrument complement, spacecraft, and orbit, the Dipper mission will gather the necessary combined electrodynamics and neutral dynamics measurements to provide an understanding of the Earth's critical boundary region where the ionized gases of space and the neutral gases of the atmosphere are coupled, and where impinging forces and momentum are deposited from the magnetosphere above and from the troposphere, stratosphere, and mesosphere below. In exploring those physical processes in the lower ionosphere which can only be measured in-situ, the Dipper mission addresses four main science objectives. The Dipper will: 1) reveal how ion-neutral coupling creates a global system of dynamo electric fields and currents; 2) provide first-hand understanding of how magnetospheric currents close in the ionosphere and reveal the effects on the upper atmosphere of magnetospheric energy and momentum deposition; 3) discover the degree of upwards coupling and energy deposition due to thunderstorm electric fields and determine their significance; 4) determine the dynamics and composition of the Earth's lower thermosphere, including its response to gravity, tidal, and planetary waves on a range of spatial scales. A proposal to design, build, operate, and analyze data from instruments on the Dipper spacecraft within the schedule and budget constraints of NASA's MIDEX program was submitted to NASA in 1998. This presentation summarizes the main features of the mission.

Pfaff, R. F., Jr.↗
NASA NTRS2000

Radiation Environment of the Chandra X-Ray Observatory

The Chandra X-ray Observatory lies in a highly elliptical orbit which dips into the outer radiation belt. During the initial stages of orbital operations, Chandra's front-illuminated CCD's (but not the back-illuminated ones) experienced an unanticipated degradation of the charge-transfer efficiency. The subsequent anomaly investigation determined that moderately low-energy protons (or other ions) propagated through the mirror assembly, causing the observed damage. This paper summarizes the effort to determine the radiation environment at the Chandra focal plane and the steps taken to prevent further performance degradation by magnetospheric and solar-wind protons and other ions.

ODell, S. L.↗
NASA NTRS2000

Southern Alaska as an Example of the Long-Term Consequences of Mountain Building Under the Influence of Glaciers

Southern Alaska is a continent-scale region of ongoing crustal deformation within the Pacific-North American plate boundary zone. Glaciers and glacial erosion have dictated patterns of denudation in the orogen over the last approx. 5 My. The orogen comprises three discrete topographic domains from south to north, respectively: (1) the Chugach/St. Elias Range; (2) the Wrangell Mountains; and (3) the eastern Alaska Range. Although present deformation is distributed across the orogen, much of the shortening and uplift are concentrated in the Chugach/St. Elias Range. A systematic increase in topographic wavelength of the range from east to west reflects east-to-west increases in the width of a shallowly-dipping segment of the plate interface, separation of major upper plate structures, and a decrease in the obliquity of plate motion relative to the plate boundary. Mean elevation decays exponentially from approx. 2500 m to approx. 1100 m from east to west, respectively. Topographic control on the present and past distribution of glaciers is indicated by close correspondence along the range between mean elevation and the modern equilibrium line altitude of glaciers (ELA) and differences in the modern ELA, mean annual precipitation and temperature across the range between the windward, southern and leeward, northern flanks. Net, range- scale erosion is the sum of: (1) primary bedrock erosion by glaciers and (2) erosion in areas of the landscape that are ice-marginal and are deglaciated at glacial minima. Oscillations between glacial and interglacial climates controls ice height and distribution, which, in turn, modulates the locus and mode of erosion in the landscape. Mean topography and the mean position of the ELA are coupled because of the competition between rock uplift, which tends to raise the ELA, and enhanced orographic precipitation accompanying mountain building, which tends to lower the ELA. Mean topography is controlled both by the 60 deg latitude and maritime setting of active deformation and by the feedback between shortening and uplift, glacial erosion, and orographic effects on climate accompanying mountain building.

Meigs, Andrew↗
NASA NTRS2000

Coupling, Q-Factor, and Integration Aspects of Microsphere Applications

With suggested applications varying from microlaser and cavity QED through optical locking of diode lasers to modulators and sensors, high-Q silica microspheres with whispering-gallery (WG) modes so far remain the subject of tabletop feasibility demonstrations. Despite the uniquely high quality-factor and submillimeter dimensions suitable for tight packaging, this novel type of high-finesse cavity still has to be adapted to fiber- and integrated-optic hardware. In the visible and near infrared-band experiments (633-850nm) measuring the ringdown time tau of free oscillations, Q = (0.6 to 0.8 ) x 10(exp 10) has been obtained in silica spheres of diameter -800 microns (corresponding tau = 3 to 4 microseconds). It was proved that under normal laboratory conditions, quality-factor is subject to deterioration within several-minute scale down to (2 ... 3 ) x 10(exp 9). The responsible mechanism was identified as adsorption of a monolayer of atmospheric water, so that preservation of the ultimate Q requires manipulation in dry environment, or fast packaging into sealed devices. Larger Q can be expected closer to minimum of attenuation in fused silica alpha = 0.2 dB/km; Q greater than or equal to 1 x 10(exp 11) at lambda=1.55 microns, with corresponding energy storage time tau approx. 0.1ms. Experiments are currently underway to determine whether this high Q can be realized experimentally. The evident difficulty is that OH-related optical absorption has its peaks located near the reported minimum of attenuation in silica. We can also mention here that some of proposed fiber materials, yet not ready for fiber drawing, have been predicted to have smaller attenuation than fused silica and may be suitable for microsphere fabrication (sodium-magnesium silicate glass, alpha = 0.06dB/km). WG modes possess very small radiative loss (it does not prevent Q-10(exp 20) and more) and therefore are electromagnetically isolated and cannot be excited by free-space beams. If no modification (such as grating) is made on the sphere surface, the coupling has to he provided by an appropriate near-field device. A systematic theoretical approach has been recently developed to quantify the performance of near-field couplers for WG modes. Efficient coupling can be obtained upon fulfillment of two main conditions: (1) mode matching and (2) sufficient coupling strength to provide the buildup of a WG mode with a given intrinsic loss. In other words, the wave in the coupler has to be phase-matched and sufficiently overlapped with the WG mode to provide enough buildup in the cavity. If the coupling efficiency is characterized by the fractional depth K(sup 2) of the resonance dip in intensity transmittance observed upon varying the frequency of the exciting wave in the coupler.

Ilchenko, V. S.↗
NASA NTRS1999

Longitudinal and Seasonal Variations in Nighttime Plasma Temperatures in the Equatorial Topside Ionosphere During Solar Maximum

Latitude profiles of the ion and electron temperatures and total ion concentration across the equatorial region near 800 km altitude are routinely obtained from Defense Meteorological Satellite Program (DMSP) spacecraft. We have examined these profiles at 2100 hours local time to discover the influences of field-aligned plasma transport induced by F region neutral winds. Such dependencies are readily seen by contrasting observations at different seasons and different longitudes distinguished by different magnetic declinations. These data show strong evidence for adiabatic heating produced by interhemispheric plasma transport. This heating manifests itself as a local temperature maximum that appears in the winter hemisphere during the solstices and is generally absent during equinox. A longitudinal variation in the appearance of this maximum is consistent with the roles of meridional and zonal winds in modulating the field-aligned plasma velocities. The data also show a local temperature minimum near the dip equator. However, it is not so easy to attribute this minimum to adiabatic cooling since transport of plasma from below and the latitude variation in the flux tube content may also produce such a minimum.

Venkatraman, Sarita↗