SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
It is suggested that fluid film thickness in a starved EHD contact is determined by the rate at which lubricant is forced from the Hertz zone normal to the rolling direction. A simple model allows calculation of this flow rate, together with related quantities of interest to the designer.
The use of Auger electron spectroscopy (AES) to search for transferred polymer must contend with the fact that there has been no published work on Auger analysis of polymers. Since this is a new area for AES, the Auger spectra of polymers and of halogenated polymers in particular is discussed. It is shown that the Auger spectra of halogenated polymers have certain characteristics that permit an assessment of whether a polymeric transfer film has been established by sliding contact. The discussion is general and the concepts should be useful in considering the Auger analysis of any polymer. The polymers chosen for this study are the halogenated polymers polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC), and polychlorotrifluorethylene (PCTFE).
Transparent conducting coating is applied to narrow pn junction surface to provide ohmic contact for majority carrier flow. Coating can be made thick to prevent series resistance problem.
Method enables use of crystal or semiconductor materials with selective spectral-response characteristics (ultraviolet, visible, or infrared wavelengths) in fabrication of contact lenses, reading glasses, and photographic processing equipment.
The basic rawinsonde data are described at each pressure contact from the surface to sounding termination for the 54 stations participating in the AVE 2 pilot experiment. Soundings were taken at three-hour intervals from stations within the United States east of about 105 degrees west longitude. Methods of data reduction and estimates of data accuracy are discussed. Examples of the data records produced are shown. The AVE 2 pilot experiment was conducted as part of NASA's program to better understand and establish the extent of applications for meteorological satellite sensor data through correlative ground truth experiments and to provide basic experimental data for use in studies of atmospheric scales-of-motion interrelationships.
The contact and the crack problems for an elastic wedge of arbitrary angle are considered. The problem is reduced to a singular integral equation which, in the general case, may have a generalized Cauchy kernel. The singularities under the stamp as well as at the wedge apex were studied, and the relevant stress intensity factors are defined. The problem was solved for various wedge geometries and loading conditions. The results may be applicable to certain foundation problems and to crack problems in symmetrically loaded wedges in which cracks initiate from the apex.
A concise mathematical model is developed for surface fatigue life of low-contact-ratio spur gears. The expected fatigue life of the pinion, gear, or gear sets may be calculated from the model. An equation for the dynamic capacity of the gear set was also derived in terms of the transmitted tangential tooth load which will give a 10-percent fatigue life of one million pinion revolutions. The theoretical life was compared with experimental data for a set of VAR AISI 9310 gears operating at a Hertz stress of 1.71X10 to the 9th power newtons per square meter (248,000 psi) and 10 000 revolutions per minute. Good agreement was obtained between the experimental and theoretical surface fatigue life of the gears.
An optical EHD machine is described which will measure the thickness of elastohydrodynamic lubricant films in rolling/sliding contacts while a traction force is applied to the film. A convenient way of plotting friction coefficient against slide/roll ratio is proposed. For 13 pure fluids with well-established physical properties, the value of the peak friction coefficient was found to lie between 0.011 and 0.09.
It is shown that the surface density of accumulated electrons on a wall in contact with a plasma can be expressed as a simple function of the Debye shielding distance in the plasma. The result may have applications to problems involving objects immersed in a space plasma.
Use of device eliminates crimp connectors and ferrules, resulting in compact termination assembly and efficient use of back-shell space. Pair of insulator rings, one at each end of assembly, provides spacing between disc caps and contact rings.
Infrared emission spectra from an operating EHD sliding contact were obtained through a diamond window for an aromatic polymer solute present in equal concentration in four different fluids. Three different temperature ranges, three different loads, and three different speeds for every load were examined. Very sensitive Fourier spectrophotometric (Interferometric) techniques were employed. Band Intensities and band intensity ratios found to depend both on the operating parameters and on the fluid. Fluid film and metal surface temperatures were calculated from the spectra and their dependence on the mechanical parameters plotted. The difference between these temperatures could be plotted against shear rate on one curve for all fluids. However, at the same shear rate the difference between bulk fluid temperature and diamond window temperature was much higher for one of the fluids, a traction fluid, than for the others.
Basic heat transfer data for structural materials used in the Saturn 1B/V 1U component case structural design were obtained. The main emphasis is on thermal contact conductance between dissimilar metallic surfaces, since thermal conductivity values within solids have been sufficiently established previously. The test program outline and test results are described. The following materials were tested: aluminum 6061-T6 (12 samples), aluminum 356 (as cast), almag 35 (as cast), magnesium AZ91C-T4 (4 samples), and mag lithium LA-141 (2 samples).
A small diamond disk mounted as a window in a steel plate was covered with test fluid, and a weighted steel ball was rotated over the window so as to form a sliding elastohydrodynamic (EHD) contact region. Some of the radiant energy generated in this region, both in the fluid and at the boundaries, passed through the window into an infrared interferometer, giving rise to an emission spectrum. This spectrum could be separated into contributions from the fluid and from the ball surface, making it possible, by appropriate calibrations, to estimate their temperatures separately under operating conditions. Moreover, the shape of the discrete spectral bands of the fluid permitted some inferences on its state. Two fluids were studied under identical mechanical conditions, a polyester and a naphthenic oil, each containing an equal amount of polymethylstyrene as a spectral indicator. Differences of band intensity, band width, and frequency could, therefore, be attributed to differences in the behavior of the base fluid.
Bimetallic contacts utilizing palladium and aluminum, gold, silver, or chromium, are used in reduction of series resistance in GaAlAs/GaAs solar cells, thereby improving cell reliability.
Aluminum-silicon contacts with very thin interfacial oxide layers and various surface impurity concentrations are studied for both n and p-type silicon. To determine the surface impurity concentrations on p(+)-p and n(+)-n structures, a modified C-V technique was utilized. Effects of interfacial oxide layers and surface impurity concentrations on current-voltage characteristics are discussed based on the energy band diagrams from the conductance-voltage plots. The interfacial oxide and aluminum layer causes image contrasts on X-ray topographs.
The influence of the ellipticity parameter and the dimensionless speed U, load W, and material G parameters on minimum film thickness was investigated. The ellipticity parameter k was varied from 1 (a ball-on-plate configuration) to 8 (a configuration approaching a line contact). The dimensionless speed parameter was varied over a range of nearly two orders of magnitude. And the dimensionless load parameter was varied over a range of one order of magnitude. Conditions corresponding to the use of solid materials of bronze, steel, and silicon nitride and lubricants of paraffinic and naphthenic mineral oils were considered in obtaining the exponent on the dimensionless material parameter.
The ferrograph was used to analyze wear debris generated in a sliding elastohydrodynamic contact. The amount of wear debris correlates well with the ratio of film thickness to composite surface roughness. Essentially all of the generated wear particles were of the normal rubbing wear type.
Elastohydrodynamic lubrication concepts of conjunctions of elliptical form are applied to materials of low elastic modulus. The influence of the ellipticity parameter and the dimensionless speed, load, and material parameters on minimum film thickness for these materials has been investigated. The ellipticity parameter was varied from a ball on plate configuration to a configuration approaching a line contact. The dimensionless speed and load parameters were varied by 1 order of magnitude. Seventeen different cases were used to generate minimum and central film thickness relations. Contour plots are presented that illustrate the pressure distribution and film thickness in the conjunction.