Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Composite models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Effects of thermal loading on foil and sheet composites with constituents of differing thermal expansivities.

A study was made to estimate the magnitudes of elastic stresses and elastic-plastic stresses and strains in sheet or foil laminar composites. Using a model tungsten/80Ni + 20Cr laminar composite and assuming cooling or heating through a temperature range of 80-2000 deg F (26.5-1093.5 deg C), calculated elastic stresses exceeded published or estimated strengths of the constituents. Elastic-plastic stress-strain solutions resulted in lower estimated stress levels but with the concomitant occurrence of sufficiently large strain ranges to suggest possible thermal fatigue problems. Limited experimental studies using tungsten/80Ni + 20Cr foil and sheet laminar composites, slowly cycled between 80 and 2000 deg F (26.5-1093.5 deg C) or rapidly cycled between 80 and 1600 deg F (26.5-871 deg C) produced varying degrees of observable structural damage in from 1 to 11 cycles depending upon temperature transition rate and laminae thickness; these particular results might not occur with other combinations of materials.

Hoffman, C. A.↗
NASA NTRS1982

Observation of additional low-degree 5-min modes of solar oscillation

High-order solar oscillations with degrees l=3, 4, and 5 could be detected. The observations were made by measuring the difference between the shifts in the Fe 5,124 spectrum line from light integrated from a central circular portion of the solar disk and from an annular portion exterior to it. The frequencies of the octupole modes agree well with the values obtained from whole-disk measurements at the South Pole. A least-squares fit of the observed frequencies to values interpolated between and extrapolated from the predictions of a sequence of solar models with different chemical compositions selects two models. One, a helium-rich solution, agrees with that of similar analyses of whole-disk data. The extrapolated solution has a relatively deep convection zone, and is thus consistent with analyses of 5-min oscillations of high degree.

Scherrer, P. H.↗
NASA NTRS1988

Measurements of the gas temperature and iron abundance distribution in the Coma Cluster

The medium energy X-ray detectors onboard the EXOSAT Observatory have been used to determine the gas temperature at several positions in the Coma Cluster of galaxies. Evidence is found at greater than 95 percent confidence for a higher temperature in the center of the cluster than in a position approximately 45 arcmin off-center. No difference in iron abundance is observed between the center and off-center regions and the equilibrium model for the distribution of elements in the Coma Cluster of Abramopoulos, Chanan, and Ku can be rejected with greater than 99.5 percent confidence, in favor of a model with more uniform composition. A phenomenological model is presented of the Coma Cluster, which is consistent with the data presented here, as well as the imaging data from the Einstein Observatory and the Tenma X-ray spectrum. The model has a central isothermal region of temperature about 9 keV extending to about 25 arcmin (about 1 Mpc). Beyond this radius the temperature falls as a polytrope with index about 1.6.

Hughes, John P.↗
NASA NTRS1993

Radiation fluxes at the FIFE site

The main objective of the International Satellite Land Surface Climatology Project (ISLSCP) has been stated as 'the development of techniques that may be applied to satellite observations of the radiation reflected and emitted from the Earth to yield quantitative information concerning land surface climatological conditions'. The major field study, FIFE (the First ISLSCP Field Experiment), was conducted in 1987-89 to accomplish this objective. Four intensive field campaigns (IFC's) were carried out in 1987 and one in 1989. Factors contributing to observed reflected radiation from the FIFE site must be understood before the radiation observed by satellites can be used to quantify surface processes. Our last report (Walter-Shea et al., 1992b) focused on slope effects on incoming and outgoing shortwave radiation and net radiation from data collected in 1989. We report here on the final analysis of the slope data as well as results from thermal radiation studies conducted during the FIFE experiment. The specific areas reported are the following: (1) analysis of slope effects on measured reflectance values and estimates of surface albedo; (2) using remotely-measured surface temperatures as a means of estimating sensible heat flux from the Konza Prairie; (3) extracting canopy temperatures from remotely-measured composite surface temperatures; (4) modeling the measured composite temperature of partially vegetated surfaces; and (5) estimating gap distribution in partially vegetated surfaces from reflectance measurements.

Walter-Shea, Elizabeth A.↗
NASA NTRS2005

STOP Modeling for the JWST: Techniques, Results, and Sensitivities

The James Web Space Telescope (JWST) is a large, infrared-optimized, space telescope scheduled for launch to L2 in 2011. It must meet rigorous thermal stability requirements, almost all of which will be verified through analysis. Terrestrial testing will be performed but even that will require significant analytical interpretation of results. Preliminary analysis indicates that traditional second-order effects could cause the telescope to exceed established performance requirements. This leads to very large detailed models, primarily since composite tubes are being modeled using solid elements. To minimize differences between the current baseline and the model the project is using a number of rapid analysis cycles. The large size of the telescope models and the short cycle time creates a demanding multidisciplinary analysis environment.

John D. Johnston↗
NASA NTRS2006

The X-ray Halo of GX5-1

Using Chandra observations we have measured the energy-resolved dust-scattered X-ray halo around the low-mass X-ray binary GX5-1, detecting for the first time multiply scattered X-rays from interstellar dust. % e compared the observed X-ray halo at various energies to predictions from a range of dust models. These fits used both smoothly-distributed dust as well as dust in clumped clouds, with CO and 21 cm observations helping to determine the position of the clouds along the line of sight. We found that the BARE-GR-B model of Zubko, Dwek & Arendt (2004) generally led to the best results, although inadequacies in both the overall model and the data limit our conclusions. We did find that the composite dust models of Zubko, Dwek & Arendt (2004), especially the "no carbon" models, gave uniformly poor results. Although models using cloud positions and densities derived naively from CO and 21 cm data gave generally poor results, plausible adjustments to the distance of the largest cloud and the mass of a cloud in the expanding 3 kpc Arm lead to significantly improved fits. We suggest that combining X-ray halo, CO, and 21 cm observations will be a fruitful method to improve our understanding of both the gas and dust phases of the interstellar medium.

Smith, Randall K.↗
NASA NTRS2013

Exoplanet Transit Spectroscopy Using WFC3: WASP-12 b, WASP-17 b, and WASP-19 b

We report an analysis of transit spectroscopy of the extrasolar planets WASP-12 b, WASP-17 b, and WASP-19 b using the Wide Field Camera 3 (WFC3) on the Hubble Space Telescope (HST). We analyze the data for a single transit for each planet using a strategy similar, in certain aspects, to the techniques used by Berta et al., but we extend their methodology to allow us to correct for channel- or wavelength-dependent instrumental effects by utilizing the band-integrated time series and measurements of the drift of the spectrum on the detector over time. We achieve almost photon-limited results for individual spectral bins, but the uncertainties in the transit depth for the band-integrated data are exacerbated by the uneven sampling of the light curve imposed by the orbital phasing of HST's observations. Our final transit spectra for all three objects are consistent with the presence of a broad absorption feature at 1.4 nano meter most likely due to water. However, the amplitude of the absorption is less than that expected based on previous observations with Spitzer, possibly due to hazes absorbing in the NIR or non-solar compositions. The degeneracy of models with different compositions and temperature structures combined with the low amplitude of any features in the data preclude our ability to place unambiguous constraints on the atmospheric composition without additional observations with WFC3 to improve the signal-to-noise ratio and/or a comprehensive multi-wavelength analysis.

Atmospheres↗
NASA NTRS2013

Exoplanet Transit Spectroscopy Using WFC3: WASP-12b, WASP-17b, and WASP-19b

We report an analysis of transit spectroscopy of the extrasolar planets WASP-12 b, WASP-17 b, and WASP-19 b using the Wide Field Camera 3 (WFC3) on the Hubble Space Telescope (HST). We analyze the data for a single transit for each planet using a strategy similar, in certain aspects, to the techniques used by Berta et al., but we extend their methodology to allow us to correct for channel- or wavelength-dependent instrumental effects by utilizing the band-integrated time series and measurements of the drift of the spectrum on the detector over time. We achieve almost photon-limited results for individual spectral bins, but the uncertainties in the transit depth for the band-integrated data are exacerbated by the uneven sampling of the light curve imposed by the orbital phasing of HST's observations. Our final transit spectra for all three objects are consistent with the presence of a broad absorption feature at 1.4 microns most likely due to water. However, the amplitude of the absorption is less than that expected based on previous observations with Spitzer, possibly due to hazes absorbing in the NIR or non-solar compositions. The degeneracy of models with different compositions and temperature structures combined with the low amplitude of any features in the data preclude our ability to place unambiguous constraints on the atmospheric composition without additional observations with WFC3 to improve the signal-to-noise ratio and/or a comprehensive multi-wavelength analysis. Key words: planetary systems - techniques: photometric - techniques: spectroscopic

HST↗
NASA NTRS1990

Evaluation of several micromechanics models for discontinuously reinforced metal matrix composites

A systematic experimental evaluation of whisker and particulate reinforced aluminum matrix composites was conducted to assess the variation in tensile properties with reinforcement type, volume fraction, and specimen thickness. Each material was evaluated in three thicknesses, 1.8, 3.18, and 6.35 mm, to determine the size, distribution, and orientation of the reinforcements. This information was used to evaluate several micromechanical models that predict composite moduli. The longitudinal and transverse moduli were predicted for reinforced aluminum. The Paul model, the Cox model and the Halpin-Tsai model were evaluated. The Paul model gave a good upper bound prediction for the particulate reinforced composites but under predicted whisker reinforced composite moduli. The Cox model gave good moduli predictions for the whisker reinforcement, but was too low for the particulate. The Halpin-Tsai model gave good results for both whisker and particulate reinforced composites. An approach using a trigonometric projection of whisker length to predict the fiber contribution to the modulus in the longitudinal and transverse directions was compared to the more conventional lamination theory approach.

Johnson, W. Steven↗
NASA NTRS1991

Comparison of some micromechanics models for discontinuously reinforced metal matrix composites

A systematic experimental evaluation of whisker and particulate reinforced aluminum matrix composites was conducted to assess the variation in tensile properties with reinforcement type, volume fraction, and specimen thickness. Each material was evaluated in three thicknesses, 1.8, 3.18, and 6.35 mm, to determine the size, distribution, and orientation of the reinforcements. This information was used to evaluate several micromechanical models that predict composite moduli. The longitudinal and transverse moduli were predicted for reinforced aluminum. The Paul model, the Cox model and the Halpin-Tsai model were evaluated. The Paul model gave a good upper bound prediction for the particulate reinforced composites but under predicted whisker reinforced composite moduli. The Cox model gave good moduli predictions for the whisker reinforcement, but was too low for the particulate. The Halpin-Tsai model gave good results for both whisker and particulate reinforced composites. An approach using a trigonometric projection of whisker length to predict the fiber contribution to the modulus in the longitudinal and transverse directions was compared to the more conventional lamination theory approach.

Johnson, W. S.↗
NASA NTRS1996

Neutron diffraction measurements and modeling of residual strains in metal matrix composites

Neutron diffraction measurements at room temperature are used to characterize the residual strains in tungsten fiber-reinforced copper matrix, tungsten fiber-reinforced Kanthal matrix, and diamond particulate-reinforced copper matrix composites. Results of finite element modeling are compared with the neutron diffraction data. In tungsten/Kanthal composites, the fibers are in compression, the matrix is in tension, and the thermal residual strains are a strong function of the volume fraction of fibers. In copper matrix composites, the matrix is in tension and the stresses are independent of the volume fraction of tungsten fibers or diamond particles and the assumed stress free temperature because of the low yield strength of the matrix phase.

Saigal, A.↗
NASA NTRS2021

Development of a Numerical Modeling Approach for Buckling Analysis of Sandwich Composite Cylindrical Shells with Selected Results

The buckling response of geometrically perfect and imperfect cylindrical sandwich shells can be investigated using nonlinear finite element analyses with two-dimensional general-purpose shell elements. Such analyses are used in the NASA Engineering and Safety Center Shell Buckling Knockdown Factor Project, which has the goal of developing new analysis-based buckling design recommendations for select classes of sandwich composite cylindrical structures under uniaxial compressive load. As such, finite element models of sandwich composite cylinders were developed and analyses were performed to predict the buckling responses of geometrically perfect and imperfect sandwich composite cylinders. The development of the selected finite-element modeling approach for a sandwich composite cylinder is discussed. Buckling-response sensitivity of geometrically imperfect sandwich cylinders for various shell element types were investigated as part of this study. Preliminary results of geometric imperfections influence on buckling response of sandwich cylinders are also presented.

Structural Modeling↗
DOE OSTI2025

Assessing modifications to the Abdul-Razzak and Ghan aerosol activation parameterization (version ARG2000) to improve simulated aerosol–cloud radiative effects in the UK Met Office Unified Model (UM version 13.0)

The representation of aerosol activation is a key source of uncertainty in global composition-climate model simulations of aerosol–cloud interactions. The Abdul-Razzak and Ghan (ARG) activation parameterization is used in several global and regional models that employ modal aerosol microphysics schemes. In this study, we investigate the ability of the ARG parameterization to reproduce simulations with a cloud parcel model and find its performance is sensitive to the geometric standard deviations (widths) of the lognormal aerosol modes. We recommend adjustments to three constant parameters in the ARG equations, which improve the performance of the parameterization for small mode widths and its ability to simulate activation in polluted conditions. For the accumulation mode width of 1.4 used in the Met Office Unified Model (UM), the modifications decrease the mean bias in the activated fraction of aerosols compared to a cloud parcel model from −6.6 % to +1.2 %. We implemented the improvements in the UM and compared simulated global cloud droplet concentrations with satellite observations. The simulated cloud radiative effect changes by −1.43 W m −2 (6 %) and aerosol indirect radiative forcing over the industrial period changes by −0.10 W m −2 (10 %).

Ghosh, Pratapaditya [Carnegie Mellon University, P↗
NASA NTRS2022

Premature Deaths in Africa Due to Particulate Matter Under High and Low Warming Scenarios

Sustainable development and climate change mitigation can provide enormous public health benefits via improved air quality, especially in polluted areas. We use the latest state-of-the-art composition-climate model simulations to contrast human exposure to fine particulate matter in Africa under a “baseline” scenario with high material consumption, population growth, and warming to that projected under a sustainability scenario with lower consumption, population growth, and warming. Evaluating the mortality impacts of these exposures, we find that under the low warming scenario annual premature deaths due to PM2.5 are reduced by roughly 515,000 by 2050 relative to the high warming scenario (100,000, 175,000, 55,000, 140,000, and 45,000 in Northern, West, Central, East, and Southern Africa, respectively). This reduction rises to ∼800,000 by the 2090s, though by that time much of the difference is attributable to the projected differences in population. By contrast, during the first half of the century benefits are driven predominantly by emissions changes. Depending on the region, we find large intermodel spreads of ∼25%–50% in projected future exposures owing to different physics across the ensemble of 6 global models. The spread of projected deaths attributable to exposure to fine particulate matter, including uncertainty in the exposure-response function, are reduced in every region to ∼20%–35% by the non-linear exposure-response function. Differences between the scenarios have an even narrower spread of ∼5%–25% and are highly statistically significant in all regions for all models. These results provide valuable information for policy-makers to consider when working toward climate change mitigation and sustainable development goals.

PM2.5↗
NASA NTRS2016

Influence of Constituents on Creep Properties of SiC/SiC Composites

SiC-SiC composites are being considered as potential candidate materials for next generation turbine components such as combustor liners, nozzle vanes and blades because of their low density, high temperature capability, and tailorable mechanical properties. These composites are essentially fabricated by infiltrating matrix into a stacked array of fibers or fiber preform by one or a combination of manufacturing methods such as, Melt Infiltration (MI) of molten silicon metal, Chemical Vapor Infiltration (CVI), Polymer Infiltration and Pyrolysis (PIP). To understand the influence of constituents, the SiC-SiC composites fabricated by MI, CVI, and PIP methods were creep tested in air between 12000 and 14500 degrees Centigrade for up to 500 hours. The failed specimens were analyzed under a scanning electron microscope to assess damage mechanisms. Also, knowing the creep deformation parameters of the fiber and the matrix under the testing conditions, the creep behavior of the composites was modeled and compared with the measured data. The implications of the results on the long term durability of these composites will be discussed.

modeling↗
NASA NTRS2006

Modeling the Elastic Modulus of 2D Woven CVI SiC Composites

The use of fiber, interphase, CVI SiC minicomposites as structural elements for 2D-woven SiC fiber reinforced chemically vapor infiltrated (CVI) SiC matrix composites is demonstrated to be a viable approach to model the elastic modulus of these composite systems when tensile loaded in an orthogonal direction. The 0deg (loading direction) and 90deg (perpendicular to loading direction) oriented minicomposites as well as the open porosity and excess SiC associated with CVI SiC composites were all modeled as parallel elements using simple Rule of Mixtures techniques. Excellent agreement for a variety of 2D woven Hi-Nicalon(TradeMark) fiber-reinforced and Sylramic-iBN reinforced CVI SiC matrix composites that differed in numbers of plies, constituent content, thickness, density, and number of woven tows in either direction (i.e, balanced weaves versus unbalanced weaves) was achieved. It was found that elastic modulus was not only dependent on constituent content, but also the degree to which 90deg minicomposites carried load. This depended on the degree of interaction between 90deg and 0deg minicomposites which was quantified to some extent by composite density. The relationships developed here for elastic modulus only necessitated the knowledge of the fractional contents of fiber, interphase and CVI SiC as well as the tow size and shape. It was concluded that such relationships are fairly robust for orthogonally loaded 2D woven CVI SiC composite system and can be implemented by ceramic matrix composite component modelers and designers for modeling the local stiffness in simple or complex parts fabricated with variable constituent contents.

Morscher, Gregory N.↗