Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Carbide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Design and evaluation of experimental ceramic automobile thermal reactors

The paper summarizes the results obtained in an exploratory evaluation of ceramics for automobile thermal reactors. Candidate ceramic materials were evaluated in several reactor designs using both engine dynamometer and vehicle road tests. Silicon carbide contained in a corrugated metal support structure exhibited the best performance, lasting 1100 hours in engine dynamometer tests and for more than 38,600 kilimeters (24,000 miles) in vehicle road tests. Although reactors containing glass-ceramic components did not perform as well as silicon carbide, the glass-ceramics still offer good potential for reactor use with improved reactor designs.

Stone, P. L.↗
NASA NTRS1975

The effect of thermal exposure on the mechanical properties of aluminum-graphite composites

The mechanical properties of aluminum-graphite composites were measured at room temperature in the as-received condition, after elevated temperature exposure and after thermal cycling. The composites were fabricated by solid-state diffusion bonding of liquid-phase Al-infiltrated Thornel 50 fibers. The results showed that the maximum longitudinal tensile strength of the as-received material was 80,000 psi, which corresponds well with the rule of mixture value. The composite strength was observed to vary widely, depending on the extent of wetting of the fibers by the aluminum. The strength of the composites in the transverse direction was generally very low, due to poor interfacial bonding. Aluminum carbide (Al4C3) formed at the surface of the fibers at temperatures greater than 500 C. Development of the carbide was shown to be diffusion-controlled and was dependent on the time and temperature used. It was shown that the tensile strength was virtually unaffected by heat-treatment up to 500 C; beyond that temperature a drastic degradation of tensile strength occurred. Thermal cycling of the composites below 500 C resulted in an observable degradation of the composite strength.

Khan, I. H.↗
NASA NTRS1976

Work function determination of promising electrode materials for thermionic energy converters

The work function determinations of candidate materials for low temperature (1400 K) thermionics through vacuum emission tests are discussed. Two systems, a vacuum emission test vehicle and a thermionic emission microscope are used for emission measurements. Some nickel and cobalt based super alloys were preliminarily examined. High temperature physical properties and corrosion behavior of some super alloy candidates are presented. The corrosion behavior of sodium is of particular interest since topping cycles might use sodium heat transfer loops. A Marchuk tube was designed for plasma discharge studies with the carbide and possibly some super alloy samples. A series of metal carbides and other alloys were fabricated and tested in a special high temperature mass spectrometer. This information coupled with work function determinations was evaluated in an attempt to learn how electron bonding occurs in transition alloys.

Jacobson, D.↗
NASA NTRS1975

Improving the toughness of refractory compounds

Composition and processing studies were conducted on silicon nitride and silicon carbide materials. Charpy mode impact testing to 2415 F established the effectiveness of higher purity silicon nitride powder sources in reducing the scatter of measurements and in improving short time bend strengths as well as bend stress rupture properties. Stabilized zirconia additions in particular were observed to dramatically enhance low and high temperature bend strengths and stress rupture properties for all grades of silicon nitride powder. Silicon carbide samples showed relatively poor impact resistance, although the maxima in stress rupture behavior was exhibited by this material.

Vasilos, T.↗
NASA NTRS1977

Reinforced Carbon Carbon (RCC) oxidation resistant material samples - Baseline coated, and baseline coated with tetraethyl orthosilicate (TEOS) impregnation

Reinforced carbon-carbon material specimens were machined from 19 and 33 ply flat panels which were fabricated and processed in accordance with the specifications and procedures accepted for the fabrication and processing of the leading edge structural subsystem (LESS) elements for the space shuttle orbiter. The specimens were then baseline coated and tetraethyl orthosilicate impregnated, as applicable, in accordance with the procedures and requirements of the appropriate LESS production specifications. Three heater bars were ATJ graphite silicon carbide coated with the Vought 'pack cementation' coating process, and three were stackpole grade 2020 graphite silicon carbide coated with the chemical vapor deposition process utilized by Vought in coating the LESS shell development program entry heater elements. Nondestructive test results are reported.

Gantz, E. E.↗
NASA NTRS1977

Characterization, shaping, and joining of SiC/superalloy sheet for exhaust system components

Hafnium carbide was shown to be virtually inert when in contact with silicon carbide and Waspaloy for at least 200 hr at 1093 C (2000 F). Extensive interaction was noted with other superalloys such as HA-188. A continuous CVD HfC deposition process was developed for deposition of up to 8 microns on .14 mm (.0056 in.) SiC tungsten core filament at rates as high as .6 m/min. The rate can be increased by increasing the length of the reactor and the output of the power supply used in resistive heating of the filament substrate. The strength of HfC coated filament varies with thickness in a Griffith-like manner. This strength reduction was greater for HfC coatings than for tungsten coatings, presumably because of the greater ductility of tungsten.

Cornie, J. A.↗
NASA NTRS1978

Determination of the Fe-rich portion of the Fe-Ni-C phase diagram

The iron-enriched section of the phase diagram for the ternary alloy Fe-Ni-C of various compositions is determined at 773, 873, 923, and 1003 C. The two-phase tie lines and three-phase tie triangles are measured by electron microprobe analyses. Tie lines in samples without bulk equilibrium are obtained by extrapolated interface compositions under the assumption of local equilibrium at the interface. It is shown that Ni addition somewhat reduces carbon solubility in austenite while decreasing the stability of the carbide phase. In particular, the carbide is always poor in Ni relative to the coexisting metal phase(s).

Romig, A. D., Jr.↗
NASA NTRS1978

Opacified silica reusable surface insulation /RSI/ for thermal protection of the Space Shuttle Orbiter

A reusable surface insulation (RSI) material adopted for use on limited areas of the Orbiter's heat shield is described. The RSI is a rigid sintered fibrous silica material containing about 3% by weight of 1200-grit silicon carbide powder. RSI manufacture is described; strength characteristics and thermal conductivity of the final product can be tailored by controlling the isotropy, and the density, coefficient of thermal expansion, and specific heat are reported. Data establishing that opacification of RSI with silicon carbide lowers the thermal conductivity are presented.

Goldstein, H. E.↗
NASA NTRS1978

Opacified silica reusable surface insulation /RSI/ for thermal protection of the Space Shuttle Orbiter

The present paper deals with a second-generation reusable surface insulation (RSI) material, termed LI-2200, which has been chosen for use on limited areas of the Orbiter heat shield. It is a rigid sintered fibrous silica containing about 3% by weight 1200 grit silicon carbide powder, capable of surviving multiple reentries at temperatures on the order of 1400 C. The lower thermal conductivity achieved by opacification with silicon carbide is demonstrated by radiant transmission measurements and thermal response tests.

Goldstein, H. E.↗
NASA NTRS1979

Linear ruby scale and one megabar

The accuracy and validity of certain techniques used in studying high-pressure transitions have been investigated. Experiments which place upper limits of about 20 GPa and about 50 GPa on pressures practically attainable using uniaxial supported opposed anvil devices with tungsten carbide pistons and uniaxial opposed flat anvil diamond devices, respectively, are reported. Direct static determinations of the transition pressures of GaP by two different methods are described. The values obtained indicate that the linear ruby scale increasingly overestimates the transition pressure as the pressure rises above 10 GPa. It is further shown that the use of shock-based marker materials, such as silver, as the basis of pressure measurement in X-ray diffraction studies leads to bulk moduli of cubic carbides which are in extreme disagreement with expected values.

Ruoff, A. L.↗
NASA NTRS1982

Technique for Machining Glass

Process for machining glass with conventional carbide tools requires a small quantity of a lubricant for aluminum applied to area of glass to be machined. A carbide tool is then placed against workpiece with light pressure. Tool is raised periodically to clear work of glass dust and particles. Additional lubricant is applied as it is displaced.

Rice, S. H.↗
NASA NTRS1982

Prolonging the Life of Refractory Fillers

Useful life of a refractory glass cloth gap filler is increased by coating it with a suspension of silicon carbide in butanol and polyethylene. Coating is applied to the refractory filler that seals gaps between insulating tiles on the Space Shuttle orbiter. Silicon carbide coating prevents embrittlement at high temperatures such as those encountered on reentry into Earth's atmosphere.

Schomburg, C.↗
NASA NTRS1980

Improved refractory coatings

The adhesion, friction and wear properties of sputtered refractory coatings on substrates of materials that form stable nitrides are enhanced by placing each substrate directly below a titanium carbide target of a commercial radiofrequency diode apparatus in a vacuum chamber. Nitrogen is bled into the system through a nozzle resulting in a small partial pressure of about 0.5% to 2.5% during the first two minutes of deposition. The flow of nitrogen is then stopped, and the sputtering ambient is reduced to pure argon through a nozzle without interrupting the sputtering process. When nitrogen is deliberately introduced during the crucial interface formation, some of the titanium at the interface reacts to form titanium nitride while the metal of the substrate also forms the nitride. These two nitrides atomically mixed together in the interfacial region act to more strongly bond the growing titanium carbide coating as it forms on the substrate.

Brainard, W. A.↗
NASA NTRS1980

Non-noble catalysts and catalyst supports for phosphoric acid fuel cells

Tungsten carbide, which is known to be active for hydrogen oxidation and CO tolerant has a hexagonal structure. Titanium carbide is inactive and has a cubic structure. Four different samples of the cubic alloys Wx-1TixC were prepared and found to be active and CO tolerant. These alloys are of interest as possible phosphoric acid fuel cell catalysts. They also are of interest as opportunities to study the activity of W in a different crystalline environment and to correlate the activities of the surface sites with surface composition.

Mcalister, A. J.↗
NASA NTRS1981

Adhesion and friction of transition metals in contact with nonmetallic hard materials

Sliding friction experiments were conducted with the metals yttrium, titanium, tantalum, zirconium, vanadium, neodymium, iron, cobalt, nickel, tungsten, platinum, rhenium, ruthenium, and rhodium in sliding contact with single crystal diamond, silicon carbide, pyrolytic boron nitride, and ferrite. Auger electron spectroscopy analysis was conducted with the metals and nonmetals to determine the surface chemistry and the degree of surface cleanliness. The results of the investigation indicate the adhesion and friction of the transition metals in contact with diamond, silicon carbide, boron nitride, and ferrite are related to the relative chemical activity of the metals. The more chemically active the metal, the higher the coefficient of friction and the greater amount of transfer to the nonmetals.

Miyoshi, K.↗
NASA NTRS1980

Surface flaw detection in structural ceramics by scanning photoacoustic spectroscopy

Laser-scanned photoacoustic spectroscopy has been used to detect tightly closed surface cracks in three structural ceramic materials: sintered silicon nitride, reaction-bonded silicon nitride, and sintered silicon carbide. It is found that the amplitude of the photoacoustic signal from the flaws is greater for the silicon nitrides than for silicon carbide, which is attributed to the lower thermal diffusivity of silicon nitride as well as differences in the grain size distribution and chemical composition. Signal amplitude, reproducibility, and signal-to-noise ratio are acceptable for effective flaw detection

Khandelwal, P. K.↗
NASA NTRS1983

Asymmetric Die Grows Purer Silicon Ribbon

Concentration of carbide impurities in silicon ribbon is reduced by growing crystalline ribbon with die one wall higher than other. Height difference controls shape of meniscus at liquid/crystal interface and concentrates silicon carbide impurity near one of broad faces. Opposite face is left with above-average purity. Significantly improves efficiency of solar cells made from ribbon.

Kalejs, J. P.↗
NASA NTRS1981

Ultrasonic velocity for estimating density of structural ceramics

The feasibility of using ultrasonic velocity as a measure of bulk density of sintered alpha silicon carbide was investigated. The material studied was either in the as-sintered condition or hot isostatically pressed in the temperature range from 1850 to 2050 C. Densities varied from approximately 2.8 to 3.2 g cu cm. Results show that the bulk, nominal density of structural grade silicon carbide articles can be estimated from ultrasonic velocity measurements to within 1 percent using 20 MHz longitudinal waves and a commercially available ultrasonic time intervalometer. The ultrasonic velocity measurement technique shows promise for screening out material with unacceptably low density levels.

Klima, S. J.↗