Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced Fuels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Spanning the Core Design Space with Binary Perturbations - A Mathematical Investigation

A reactor core design engineer, even one with many years of experience or one using advanced fuel pattern optimization software, will likely fine tune the pattern before finalizing the design. Fine tuning can further minimize local enthalpy peaks, optimize reactivity to extend burnup, and add additional margin to limits on reactivity coefficients or heat flux. For reactors that have reached an equilibrium fuel cycle, the number of feeds each cycle is typically the similar to previous cycles as is their placement in the core. It is then the engineer's responsibly to efficiently select the placement of burned assemblies to ensure optimal fuel utilization, satisfy safety limits, and meet cycle energy requirements. One of the engineer's most commonly used tools in this fine tuning investigation is to swap the positions of two assemblies, most likely two previously irradiated ('burned') assemblies since their reactivity is lower than fresh fuel. Such an operation is referred to in this work as a binary perturbation or a 'swap'. If quarter core symmetry is maintained, the perturbation translates to the other three quadrants. Likewise if eighth core symmetry is maintained, the perturbation translates to other seven octants. The question is then, how much of the core design space can binary perturbations possibly span? This work seeks to quantitatively define the space spanned by m number of binary perturbations as a function of variable size through combinatorial principles and computer simulation. The results of this study are useful in understanding the in-core fuel management problem faced by both professionals who employ hand manipulations and those who attempt stochastic solutions of the problem.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance of the HERA Pre-Hydrided Experiments

Presentation on the status of the HERA Pre-hydrided Experiments performed at TREAT to be presented at the Advanced Fuels Campaign Annual Program Review Meeting.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

LDRD Concluding Poster for Project 23A1070-162FP

This is the poster for the concluding LDRD project, Development of Two-Phase Separation Techniques for Advanced Fuel Cycle Studies, Project number: 23A1070-162FP.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗

Gap Size Uncertainty Quantification in Advanced Gas Reactor TRISO Fuel Irradiation Experiments

The Advanced Gas Reactor (AGR)-3/4 experiment is the combination of the third and fourth tests conducted within the tristructural isotropic fuel development and qualification research program. The AGR-3/4 test consists of twelve independent capsules containing a fuel stack in the center surrounded by three graphite cylinders and shrouded by a stainless steel shell. This capsule design enables temperature control of both the fuel and the graphite rings by varying the neon/helium gas mixture flowing through the four resulting gaps. Knowledge of fuel and graphite temperatures is crucial for establishing the functional relationship between fission product release and irradiation thermal conditions. These temperatures are predicted for each capsule using the commercial finite-element heat transfer code ABAQUS. Uncertainty quantification reveals that the gap size uncertainties are among the dominant factors contributing to predicted temperature uncertainty due to high input sensitivity and uncertainty. Gap size uncertainty originates from the fact that all gap sizes vary with time due to dimensional changes of the fuel compacts and three graphite rings caused by extended exposure to high temperatures and fast neutron irradiation. Gap sizes are estimated using as-fabricated dimensional measurements at the start of irradiation and post irradiation examination dimensional measurements at the end of irradiation. Uncertainties in these measurements provide a basis for quantifying gap size uncertainty. However, lack of gap size measurements during irradiation and lack of knowledge about the dimension change rates lead to gap size modeling assumptions, which could increase gap size uncertainty. In addition, the dimensional measurements are performed at room temperature, and must be corrected to account for thermal expansion of the materials at high irradiation temperatures. Uncertainty in the thermal expansion coefficients for the graphite materials used in the AGR-3/4 capsules also increases gap size uncertainty. This study focuses on analysis of modeling assumptions and uncertainty sources to evaluate their impacts on the gap size uncertainty.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FY2017 Advanced Combustion Systems and Fuels Annual Progress Report

The Advanced Combustion Systems and Fuels Program supports VTO’s goal and focuses early-stage research and development (R&D) to improve understanding of the combustion processes, fuel properties, and emission control technologies while generating knowledge and insight necessary for industry to develop the next generation of engines.

33 ADVANCED PROPULSION SYSTEMS↗

Accelerated Irradiation Testing of Miniature Nuclear Fuel and Cladding Specimens

Qualification of advanced nuclear fuels and materials requires irradiation testing to provide input to predictive models for licensing. Oak Ridge National Laboratory has a long history of performing accelerated irradiation testing and post-irradiation examination (PIE) of miniature material specimens to determine the evolution of microstructure and thermophysical properties, leveraging the High Flux Isotope Reactor, dedicated hot cells, and instruments for handling small, low-level radioactive samples. This work gives a brief overview of irradiation testing of miniature samples to support qualification of advanced fuel cladding materials such as FeCrAl alloys and SiC ceramic matrix composites. More recent work has enabled separate effects irradiation testing of miniature fuel specimens. The small fuel size essentially decouples fuel temperature from fission rate, allowing for highly accelerated testing without large temperature gradients. This paper briefly highlights the new mini fuel irradiation facility and its first set of experiments.

Petrie, Christian↗

Enhancing Advanced Candu Proliferation Resistance Fuel with Minor Actinides

The advanced nuclear system will significantly advance the science and technology of nuclear energy systems and to enhance the spent fuel proliferation resistance. Minor actinides (MA) are viewed more as a resource to be recycled, and transmuted to less hazardous and possibly more useful forms, rather than simply disposed of as a waste stream in an expensive repository facility. MAs can play a much larger part in the design of advanced systems and fuel cycles, not only as additional sources of useful energy, but also as direct contributors to the reactivity control of the systems into which they are incorporated. In this work, an Advanced CANDU Reactor (ACR) fuel unit lattice cell model with 43 UO 2 fuel rods will be used to investigate the effectiveness of a Minor Actinide Reduction Approach (MARA) for enhancing proliferation resistance and improving the fuel cycle performance. The main MARA objective is to increase the 238 Pu / Pu isotope ratio by using the transuranic nuclides ( 237 Np and 241 Am) in the high burnup fuel and thereby increase the proliferation resistance even for a very low fuel burnup. As a result, MARA is a very effective approach to enhance the proliferation resistance for the on power refueling ACR system nuclear fuel. The MA transmutation characteristics at different MA loadings were compared and their impact on neutronics criticality assessed. The concept of MARA, significantly increases the 238Pu/Pu ratio for proliferation resistance, as well as serves as a burnable absorber to hold-down the initial excess reactivity. It is believed that MARA can play an important role in atoms for peace and the intermediate term of nuclear energy reconnaissance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High temperature mechanical properties of fluorite crystal structured materials (CeO 2 , ThO 2 , and UO 2 ) and advanced accident tolerant fuels (U 3 Si 2 , UN, and UB 2 )

The mechanical interaction between the fuel and cladding that occurs during operation of a nuclear reactor is important to understand as it can lead to cladding failures and release of radioactive material into the coolant. Additionally, in order to develop better models of the pellet-clad mechanical interactions, the mechanical properties of the fuel at relevant operating temperatures, like the elastic moduli, are needed for current and advanced accident tolerant fuels (ATFs). In this work, elevated temperature nanoindentation and resonant ultrasound spectroscopy were used to measure the moduli and hardness of several fluorite materials (CeO 2 , ThO 2 , UO 2 ) and several ATF candidates (ATF) (U 3 Si 2 , UN, UB 2 ). In addition, a comparison of the two techniques was performed in this study to independently validate the mechanical properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The DOE Advanced Gas Reactor Fuel Development and Qualification Program

The high outlet temperatures and high thermal-energy conversion efficiency of modular High Temperature Gas-cooled Reactors (HTGRs) enable an efficient and cost effective integration of the reactor system with non-electricity generation applications, such as process heat and/or hydrogen production, for the many petrochemical and other industrial processes that require temperatures between 300°C and 900°C. The Department of Energy (DOE) has selected the HTGR concept for the Next Generation Nuclear Plant (NGNP) Project as a transformative application of nuclear energy that will demonstrate emissions-free nuclear-assisted electricity, process heat, and hydrogen production, thereby reducing greenhouse-gas emissions and enhancing energy security. The objective of the DOE Advanced Gas Reactor (AGR) Fuel Development and Qualification program is to qualify tristructural isotropic (TRISO)-coated particle fuel for use in HTGRs. The Advanced Gas Reactor Fuel Development and Qualification Program consists of five elements: fuel manufacture, fuel and materials irradiations, post-irradiation examination (PIE) and safety testing, fuel performance modeling, and fission-product transport and source term evaluation. An underlying theme for the fuel development work is the need to develop a more complete, fundamental understanding of the relationship between the fuel fabrication process and key fuel properties, the irradiation and accident safety performance of the fuel, and the release and transport of fission products in the NGNP primary coolant system. An overview of the program and recent progress is presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this paper are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

Accident Tolerant Fuels↗

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this presentation are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Simulation Aided Metallic Fuel Design

Nuclear engineering is reaching a domain space in which computational power and methods are starting to surpass the models that are used to simulate nuclear fuel rods. As these models are updated, simulations utilizing different compositions, operating conditions, fabrication techniques, and geometries can provide core designers with an important first step towards fuel qualification. Due to the cost associated with fuel irradiations, it can be expected that time and money spent building better fuel models may provide an attractive return during initial studies of advanced fuels, especially with regards to fuels beyond the extensively studied uranium oxide system. In general, the primary U.S. experience with irradiated fuel rods beyond traditional oxide fuel is with binary (U-Zr) and ternary (U-Pu-Zr) metal fuels. The bulk of the experimental data for metal fuels is obtained from rods irradiated in the EBR-II sodium fast reactor (SFR), thus many of the correlations developed for metal fuels comes from the post-irradiation (PIE) examination of EBR-II rods. One of the unique characteristics that set U-Pu-Zr fuels apart from traditional oxide fuels is the presence of different phases that develop in the fuel during irradiation. Each of these different phases has unique thermal, mechanical, and diffusive behavior. The transitions between these phases are not static as the initially homogenous zirconium diffuses towards the center and edge of the fuel rod, resulting in a low-Zr, high-U ring. Along with the differing material properties that occur in each phase, the increase in uranium corresponds to an increase in localized fission and power production. The direct coupling between the thermal and diffusion solves highlights one of the many examples of tightly coupled phenomenon that are present in nuclear fuel, and motivation for the development of codes that simultaneously solve each piece of physics in a fully-coupled manner.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluating isoprenol production using the IPP-bypass pathway in the oleaginous yeast Rhodosporidium toruloides

Background To strengthen the national energy supply, there is an increasing demand for domestically generated aviation fuels. Bio-derived advanced aviation fuels offer the opportunity to meet this domestic need while presenting a unique opportunity to investigate the production of novel aviation fuels. Isoprenol, a chemical precursor to such novel fuels, has been shown to be a biologically producible compound in model organisms, but its bio-producibility needs to be further explored in organisms more compatible with industrial bioproduction. Results In this work, we evaluate isoprenol production using the promising bioproduction yeast, Rhodosporidium toruloides. First, we show successful isoprenol production using the IPP-bypass pathways most successful in laboratory strains of E. coli and S. cerevisiae. Next, we demonstrate that increased flux through the mevalonate pathway only modestly increases isoprenol titers. Using proteomics, we identified a potential bottleneck in production at the final step in the IPP-bypass pathway and explored alternative enzymes for this step. Finally, the top three strains of R. toruloides were evaluated in sorghum hydrolysates generated using cholinium lysinate. Through this work, 93.1 mg/L of isoprenol was produced in mock medium and 27.3 mg/L in sorghum hydrolysates. Conclusion Together these results lay the foundation for future work for the production of isoprenol from bioproduction crops.

Advanced aviation fuel↗

Confirmatory Defect Analyses of AGR-5/6/7 Fuel

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program has executed a series of experiments to test and qualify tristructural isotropic (TRISO) particle fuels for use in high-temperature gas-cooled reactors. The most recent irradiation experiments, AGR-5/6/7, are testing fuel that was fabricated in near production-scale equipment. There are three important defect fractions that must be characterized, using a deconsolidation-leach-burn-leach (DLBL) method, to better predict and understand fuel performance during irradiation. These are the dispersed uranium fraction (DUF), exposed kernel fraction (EKF), and silicon carbide defect fraction (SDF). The DLBL characterization data from analyses of the four compact batches, fabricated and characterized by the BWX Technologies Nuclear Operations Group (BWXT-NOG), showed unexpectedly higher values for all three defect fractions relative to the parent TRISO particle defect fractions. The DUF and SDF should not have changed significantly during compact fabrication and the apparent increase in the EKF, a metric for particle damage, was higher than anticipated for the compacts with 40% volumetric packing fraction (PF). Analytical results showed no net increase in the EKF for the 25% PF compacts. Compacts from one compact batch of each packing fraction were sent to Oak Ridge National Laboratory (ORNL), along with uncompacted tristructural isotropic (TRISO) particles, overcoated to a thickness targeting a 40% PF, for confirmatory analyses of the defect fractions and determination of the source(s) of damage. The ORNL results did not confirm the BWXT-NOG results for either the DUF or the SDF; the ORNL results showed no significant change in these defect fractions relative to the parent TRISO particle lot. The ORNL results did, however, confirm that a large increase in the exposed kernel fraction was found in the 40% PF compacts and that the 25% PF compacts sustained little if any damage. Data suggest that a large majority of the mechanical damage to the TRISO particles occurred in the overcoater when targeting the 40% PF. The analytical laboratories at both BWXT-NOG and ORNL had inconsistent outcomes on analyses of individual batches. Although the ORNL data is more consistent with the parent TRISO lot and expectations, the data set is too limited in size to justifiably reject suspect data from either laboratory at this time. It is recommended that an additional analysis be done to provide sufficient data for estimating the true defect fractions for interpreting the radionuclide release data during the AGR-5/6/7 irradiation experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fission Product Monitoring of TRISO Coated Fuel For The Advanced Gas Reactor -1 Experiment

The US Department of Energy has embarked on a series of tests of TRISO-coated particle reactor fuel intended for use in the Very High Temperature Reactor (VHTR) as part of the Advanced Gas Reactor (AGR) program. The AGR-1 TRISO fuel experiment, currently underway, is the first in a series of eight fuel tests planned for irradiation in the Advanced Test Reactor (ATR) located at the Idaho National Laboratory (INL). The AGR-1 experiment reached a peak compact averaged burn up of 9% FIMA with no known TRISO fuel particle failures in March 2008. The burnup goal for the majority of the fuel compacts is to have a compact averaged burnup greater than 18% FIMA and a minimum compact averaged burnup of 14% FIMA. At the INL the TRISO fuel in the AGR-1 experiment is closely monitored while it is being irradiated in the ATR. The effluent monitoring system used for the AGR-1 fuel is the Fission Product Monitoring System (FPMS). The FPMS is a valuable tool that provides near real-time data indicative of the AGR-1 test fuel performance and incorporates both high-purity germanium (HPGe) gamma-ray spectrometers and sodium iodide [NaI(Tl)] scintillation detector-based gross radiation monitors. To quantify the fuel performance, release-to-birth ratios (R/B’s) of radioactive fission gases are computed. The gamma-ray spectra acquired by the AGR-1 FPMS are analyzed and used to determine the released activities of specific fission gases, while a dedicated detector provides near-real time count rate information. Isotopic build up and depletion calculations provide the associated isotopic birth rates. This paper highlights the features of the FPMS, encompassing the equipment, methods and measures that enable the calculation of the release-to-birth ratios. Some preliminary results from the AGR-1 experiment are also presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

STATUS OF TRISO FUEL IRRADIATIONS IN THE ADVANCED TEST REACTOR SUPPORTING HIGH-TEMPERATURE GAS-COOLED REACTOR DESIGNS

The United States Department of Energy’s Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) Fuel Development and Qualification Program is irradiating up to seven low enriched uranium (LEU) tri-isotopic (TRISO) particle fuel (in compact form) experiments in the Advanced Test Reactor (ATR) located at the Idaho National Laboratory (INL). These irradiations and fuel development are being accomplished to support development of the next generation reactors in the United States. The experiments will be irradiated over the next several years to demonstrate and qualify new TRISO coated particle fuel for use in high temperature gas reactors. The goals of the experiments are to provide irradiation performance data to support fuel process development, to qualify fuel for normal operating conditions, to support development and validation of fuel performance and fission product transport models and codes, and to provide irradiated fuel and materials for post irradiation examination (PIE) and safety testing. The experiments, which will each consist of several independent capsules, will be irradiated in an inert sweep gas atmosphere with individual on-line temperature monitoring and control of each capsule. The sweep gas will also have on-line fission product monitoring on its effluent to track performance of the fuel in each individual capsule during irradiation. The first experiment (designated AGR-1) started irradiation in December 2006 and was completed in November 2009. The second experiment (AGR-2) started irradiation in June 2010 and completed in October 2013. The third and fourth experiments have been combined into a single experiment designated (AGR-3/4), which started its irradiation in December 2011 and completed in April 2014. Since the purpose of this experiment was to provide data on fission product migration and retention in the NGNP reactor, the design of this experiment was significantly different from the first two experiments, though the control and monitoring systems are very similar. The final experiment, AGR-5/6/7, is scheduled to begin irradiation in early summer 2017.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗