Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ANN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Hierarchical Hybrid Multifunctional Materials through Interface Engineering

This project focuses on the development of stimuli-responsive hybrid multifunctional materials. We place emphasis on the design, synthesis, structural characterization, evaluation of functional properties (electronic, thermal and optical) of several (1-x)Cu 2 Se/(x)WBGS hierarchical bulk composites between Cu 2 Se, a narrow band gap semiconductor (NBGS), with a range of wider band gap semiconductors (WBGS) such as CuMSe 2 (M = Al, Ga, In, Fe, Cr) and Cu 4 TiSe 4 . Cu2Se is a well-studied NBGS with excellent thermoelectric properties (high electrical conductivity, large thermopower, etc.) while CuMSe 2 and Cu 4 TiSe 4 are high performance solar absorber materials (large band gap, large absorption coefficient, etc.). Our primary objectives are (i) to demonstrate the ability to integrate dissimilar functional properties such as large optical absorption coefficient and high electronic conductivity, within (1-x)Cu 2 Se/(x)WBGS composite; and (ii) to establish the correlation between the hierarchical structural entanglement of Cu 2 Se with WBGS (CuMSe 2 or Cu 4 TiSe 4 ) phase, the interactions between native electronic defects within the coexisting phases in the resulting (1-x)Cu 2 Se/(x)WBGS bulk composites , and the impacts on their electronic conductivity, thermal transport and optical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electrochemical Direct Air Capture of CO 2 Using Redox-Active Textiles

We have used vapor phase chemistry to construct a textile electrode that comprises an immobilized PCET agent, poly(1-aminoanthraquinone) (PAAQ) encapsulated within a conductive polymer, and incorporated it into CO 2 -separating electrochemical flow cells. This system facilitates pH-swing-driven carbon capture from a 1% CO 2 feed and air, with the former at a competitively low energetic cost of 202 kJ/molCO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Pressure Gain, Stability, and Operability of Methane/Syngas Based RDEs Under Steady and Transient Conditions (Final Project Report)

The scope of this work addresses key issues associated with losses associated with the detonation wave and other processes internal to the RDE operation, as well as it develops modeling tools for the evaluation of these losses and exhaust emissions in RDEs. The main challenge in studying RDEs is that RDE performance is highly reliant on the specifics of the design so much so that simple/canonical systems alone cannot provide useful engineering information, but practical RDE designs are sufficiently complex and involve extreme operational environments that detailed access either experimentally (laser diagnostics, for instance) or computationally (direct numerical simulations) are as yet to become practical. To overcome this challenge, we have conducted a combined experimental/simulation/analytical study investigating key phenomena that control the characteristics of operation of RDEs. As a result, the study has developed tools and methods that can be used to evaluate performance and design approaches using reduced-physics models, with the assumptions validated using detailed simulations, and the model prediction tested using experimental observations. The specific objectives of the research were: (1) Develop and demonstrate a low-loss fully axial injection concept, taking advantage of stratification effects to alter the detonation structure and position the wave favorably within the combustor; (2) Obtain stability and operability characteristics of an RDE across operating conditions to aid in the development of operability and performance rules for the operations of other systems; and (3) Develop quantitative metrics for performance gain as well as quantitative description of the loss mechanisms through a combination of diagnostics development, reduced-order modeling, and detailed simulations. The work conducted here has made contribution on design of low-loss inlets that has broad application within the power generation industry for use with pressure gain combustion. The operability and stability of different designs, while focusing on axial air inlet designs, has been analyzed. The effect of nozzle and injection conditions was studied. Models and simulations of exhaust emissions, focusing on NOx emission has been developed and used to investigate how operation of the RDE affect NOx production using Lagrangian analysis of RDE simulations. This work has built on previous programs, with the goal of further understanding operation of RDEs and elevate the readiness of design consideration. In addition, a suite of diagnostic and modeling tools have been developed to obtain quantitative metrics on performance based on measurements, which can be readily transferred to other experimental configurations.

08 HYDROGEN↗
DOE OSTI2025

Aerosol Particle Mixing State and Composition at AMF3 (Interim Field Campaign Report)

The campaign is designed to support deployment of aerosol sampling equipment at the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) user facility’s third ARM Mobile Facility (AMF3) to enable both singe-particle and bulk characterization of the aerosol particles at the field site in Bankhead National Forest, northern Alabama. We are proposing to do this work as part of our proposal “Generalizing aerosol mixing state: synthesis from observations and connection to models,” which has the pre-proposal tracking number PRE-0000035878. The full proposal has Dr. Rachel O’Brien as the Principal Investigator (PI) and Dr. Andy Ault and Dr. Nicole Riemer as Co-PIs. We sought to deploy instruments in winter 2025 and summer 2025 to obtain samples in different seasons, but were delayed by AMF3 set-up and availability of students and PIs. We just completed our first deployment this summer (2025) and we are interested in obtaining samples during this upcoming fall and winter to see the seasonal trends in aerosol mixing state at the site. This will provide a comparison of the impact of biogenic emissions on the mixing state and the chemical composition of the aerosol particles. Overall, the proposed study will provide key information regarding the mixing state of aerosol particles at AMF3 with direct ties to impacts of the particles on cloud formation and light scattering/absorption. From our deployment that ended las week we have some visible observations from our samples. We are observing a regular amount of black carbon on stage 6 of our Micro-Orifice Uniform Deposit Impactor (MOUDI) and we have also observed some short, large increases in aerosol loading. We hope to continue observations of these two features to determine the sources/aging for the black carbon and the physical mixing state as well as the sources for the short (a few minutes) increases in the aerosol loading and determine if the source for these is dust or sea salt or another source. We are also interested in comparing the black carbon we see here to samples collected during the agriculture burns in January/February and in comparing the larger particles to bioaerosols in the spring. To obtain these comparisons, we will need to collect more samples in the other seasons. Finally, we have some size-resolved particle collectors that can be deployed at the same time as the tethered balloon launches. We have discussed with Swarup China about trying to get the timing to work in August and we are interested in coordinating again later, if possible. This will give us ground-level and vertical aerosol mixing state sample sets that will be very exciting to analyze.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Particle Beam Acceleration Using 3 Petawatt Laser Pulses

The Zettawatt-Equivalent Ultrashort pulse laser System (ZEUS) is presently operational at the Gerard Mourou Center for Ultrafast Optical Science (CUOS) at the University of Michigan. ZEUS is a significant upgrade of the previous high power laser systems at CUOS and consists of two beamlines thatoperate in perfect synchronization. The 500 TW beamline became operational in 2023, 2 PW operation started in 2025 and full 3 PW power levels will be available in 2026. It is presently the highest power laser system in the US. In this grant the high field science group at CUOS has leveraged this unique high power laser facility to investigate laser wake field acceleration (LWFA) in ultra-high power laser plasma interactions and have shown how this can scale for future electron–positron colliders at high energy. The dual beam experimental configuration enables flexibility for many frontier experiments in laser-driven acceleration research, in particular, enabling extended channelling/acceleration experiments, positron generation/acceleration experiments and proof-of-principle transverse pumping “dephasingless” electron acceleration experiment and theory. LWFA may be able to miniaturize particle accelerators for high energy physics and also enable new sources of ultrafast, extreme brightness and precise x-rays for a wide variety of applications. In laser wake field acceleration, an electron bunch “surfs” on the electron plasma wave (the “wake field”) generated by the ponderomotive force of an intense laser. The plasma wave has a strong longitudinal electric field that stays in phase with the relativistic driver. A relativistic charged particle may, therefore, remain in phase with the accelerating field over long distances and gain ultra-relativistic energies. The accelerating electric field strength that the plasma wave can support can be many orders of magnitude higher than that of conventional accelerators, which makes laser wakefield acceleration an exciting prospect as an advanced accelerator concept. In this research project we have investigated the scaling of this mechanism to laser powers of 2 PW and have measured the x-ray emission and radio frequency emission resulting from the acceleration process. We have also performed theoretical investigation of mechanisms to scale laser driven accelerators to much higher energy using dephasingless acceleration processes.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

2024 ASER Summary: Annual Site Environmental Report Summary (Rev. 2)

The Laboratory’s Governing Policy for the Environment: (1) We are committed to act as stewards of our environment to achieve our mission in accordance with all applicable environmental requirements. (2) We set continual improvement objectives and targets, measure and document our progress, and share our results with our workforce, sponsors, and the public. (3) We reduce our environmental risk through legacy cleanup, pollution prevention, and long-term management programs.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Advanced Materials & Manufacturing Technology (AMMT): Development of Additive Manufacturing Agnostic Process Parameter Procedure, 316H Stainless Steel Readiness Level Data Sets, and Machine Maintenance Plan

The University of California, Davis is involved in a project to deploy and enhance an artificial intelligence (AI) system for predicting and preventing plasma disruptions on the DIII D tokamak, under the funding from Department of Energy DE-SC0023500 (title: AI/Deep Learning FRNN Software for Prediction & Real-Time Control of DIII-D Plasma Control System (PCS)). The overarching goal is to demonstrate that real-time, AI-guided intervention can proactively modify the plasma state to avoid or mitigate disruptions—a critical challenge for the future of fusion energy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Metadata Standards for the NSE: Extended Field Standards

This standard presents a set of optional metadata fields for managed digital objects within the Nuclear Security Enterprise (NSE) and provides a deeper look at data representation in metadata by looking at the representation of 1) Records Management required metadata, and 2) common representations of technical/scientific data. Metadata standardization is a critical enabler for effectively sharing data, documents, and other digital objects between NSE sites, and for tracing the digital thread at the object level. Standardization is necessary for both schemas and vocabularies, meaning that both field standards and value standards must be specified. This document serves as a complementary field standard, recommending an optional set of fields that should be uniformly built for all managed digital objects within the NSE. This document specifically focuses on extending the shared discovery layer defined in the first white paper by introducing additional descriptive and data representation fields that improve cross-site search and interpretation.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2026

Fluorinated Glyme Solvents to Extend Lithium-Sulfur Battery Life (Final Technical Report, Unlimited)

This project investigated a number of partially fluorinated glymes (PFGs) as electrolyte cosolvents to improve the performance of lithium-sulfur (Li-S) batteries. A major issue in Li-S cells is the electrochemical reaction of sulfur in the cathode to form lithium polysulfides (LPS) that dissolve in the electrolyte. Those LPS are electrochemically and chemically reactive at the lithium anode, resulting in lithium sulfide deposition on the anode and also electrochemical reaction at both the anode and cathode, leading to a “polysulfide shuttle” and reduced coulombic efficiency (CE) and self-discharge of the cell. PFGs reduce the solubility of LPS while maintaining good solubility of lithium salts such as LiTFSI. By adjusting the amount of PFG as cosolvent in the electrolyte, we showed that the solubility of LPS in the electrolyte can be tuned. (It is not desirable to completely eliminate LPS in the electrolyte, as they facilitate electrochemical reaction of the electrically insulating S 8 and Li 2 S within the cathode by shuttling charge between them and the conductive carbon.) Another issue in Li-S cells is degradation of the Li anode over many cycles of stripping (discharge) and plating (charge). We showed that PFGs have a beneficial effect on the physical morphology of the Li anode, SEI formation, and the CE of a Li-Li cell. Among the many PFGs tested, we found the best performance from PFGs designated PFG2 and PFG5, and these two PFGs were thoroughly studied. A systematic coin-cell study of electrolyte solvents of 90:10, 80:20, or 70:30 DME:PFG (DME = 1,2-dimethoxyethane) revealed some systematic trends: a higher percentage of PFG solvent led to substantially longer cycle life, but at the same time reduced specific capacity (mAh/g(S)) and cell capacity at higher rates. These studies used LiFSI as the electrolyte salt, as it was found to extend cycle life compared to LiTFSI. Finally, the addition of a small amount of 1,3-dioxolane (DOL) to the electrolyte was found to be beneficial. The overall optimal electrolyte solution was found to be 0.6 M LiFSI + 0.5 M LiNO 3 in 75:5:20 DME/DOL/PFG (either PFG2 or PFG5).

25 ENERGY STORAGE↗
DOE OSTI2022

Current State of 44 Ti/ 44 Sc Radionuclide Generator Systems and Separation Chemistry

We report in recent years, there has been an increased interest in 44Ti/44Sc generators as an onsite source of 44Sc for medical applications without needing a proximal cyclotron. The relatively short half-life (3.97 hours) and high positron branching ratio (94.3%) of 44Sc make it a viable candidate for positron emission tomography (PET) imaging. This review discusses current 44Ti/44Sc generator designs, focusing on their chemistry, drawbacks, post-elution processing, and relevant preclinical studies of the 44Sc for potential PET radiopharmaceuticals.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

On the minimum number of radiation field parameters to specify gas cooling and heating functions

Fast and accurate approximations of gas cooling and heating functions are needed for hydrodynamic galaxy simulations. We use machine learning to analyze atomic gas cooling and heating functions in the presence of a generalized incident local radiation field computed by Cloudy. We characterize the radiation field through binned radiation field intensities instead of the photoionization rates used in our previous work. We find a set of 6 energy bins whose intensities exhibit relatively low correlation. We use these bins as features to train machine learning models to predict Cloudy cooling and heating functions at fixed metallicity. We compare the relative SHapley Additive exPlanation (SHAP) value importance of the features. From the SHAP analysis, we identify a feature subset of 3 energy bins (0.5-1, 1-4, and 13-16Ry) with the largest importance and train additional models on this subset. We compare the mean squared errors and distribution of errors on both the entire training data table and a randomly selected 20% test set withheld from model training. The machine learning models trained with 3 and 6 bins, as well as 3 and 4 photoionization rates, have comparable accuracy everywhere, with errors ≳10 times smaller than for the interpolation table of Gnedin and Hollon (2012). We conclude that 3 energy bins (or 3 analogous photoionization rates: molecular hydrogen photodissociation, neutral hydrogen HI, and fully ionized carbon CVI) are sufficient to characterize the dependence of the gas cooling and heating functions on our assumed incident radiation field model.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Stellar reddening map from DESI imaging and spectroscopy

We present new Galactic reddening maps of the high Galactic latitude sky using DESI imaging and spectroscopy. We directly measure the reddening of 2.6 million stars by comparing the observed stellar colors in $g-r$ and $r-z$ from DESI imaging with the synthetic colors derived from DESI spectra from the first two years of the survey. The reddening in the two colors is on average consistent with the Fitzpatrick (1999) extinction curve with $R_\mathrm{V}=3.1$ . We find that our reddening maps differ significantly from the commonly used Schlegel et al. (1998) (SFD) reddening map (by up to 80 mmag in $E(B-V)$ ), and we attribute most of this difference to systematic errors in the SFD map. To validate the reddening map, we select a galaxy sample with extinction correction based on our reddening map, and this yields significantly better uniformity than the SFD extinction correction. Finally, we discuss the potential systematic errors in the DESI reddening measurements, including the photometric calibration errors that are the limiting factor on our accuracy. The $E(g-r)$ and $E(r-z)$ maps presented in this work, and for convenience their corresponding $E(B-V)$ maps with SFD calibration, are publicly available.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Enhancing weak lensing redshift distribution characterization by optimizing the Dark Energy Survey Self-Organizing Map Photo-z method

Characterization of the redshift distribution of ensembles of galaxies is pivotal for large scale structure cosmological studies. In this work, we focus on improving the Self-Organizing Map (SOM) methodology for photometric redshift estimation (SOMPZ), specifically in anticipation of the Dark Energy Survey Year 6 (DES Y6) data. This data set, featuring deeper and fainter galaxies than DES Year 3 (DES Y3), demands adapted techniques to ensure accurate recovery of the underlying redshift distribution. We investigate three strategies for enhancing the existing SOM-based approach used in DES Y3: 1) Replacing the Y3 SOM algorithm with one tailored for redshift estimation challenges; 2) Incorporating $\textit{g}$-band flux information to refine redshift estimates (i.e. using $\textit{griz}$ fluxes as opposed to only $\textit{riz}$); 3) Augmenting redshift data for galaxies where available. These methods are applied to DES Y3 data, and results are compared to the Y3 fiducial ones. Our analysis indicates significant improvements with the first two strategies, notably reducing the overlap between redshift bins. By combining strategies 1 and 2, we have successfully managed to reduce redshift bin overlap in DES Y3 by up to 66$\%$. Conversely, the third strategy, involving the addition of redshift data for selected galaxies as an additional feature in the method, yields inferior results and is abandoned. Our findings contribute to the advancement of weak lensing redshift characterization and lay the groundwork for better redshift characterization in DES Year 6 and future stage IV surveys, like the Rubin Observatory.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Challenges in Bioinformatics Workflows for Processing Microbiome Omics Data at Scale

The nascent field of microbiome science is transitioning from a descriptive approach of cataloging taxa and functions present in an environment to applying multi-omics methods to investigate microbiome dynamics and function. A large number of new tools and algorithms have been designed and used for very specific purposes on samples collected by individual investigators or groups. While these developments have been quite instructive, the ability to compare microbiome data generated by many groups of researchers is impeded by the lack of standardized application of bioinformatics methods. Additionally, there are few examples of broad bioinformatics workflows that can process metagenome, metatranscriptome, metaproteome and metabolomic data at scale, and no central hub that allows processing, or provides varied omics data that are findable, accessible, interoperable and reusable (FAIR). Here, we review some of the challenges that exist in analyzing omics data within the microbiome research sphere, and provide context on how the National Microbiome Data Collaborative has adopted a standardized and open access approach to address such challenges.

NMDC, Microbiome↗
DOE OSTI2022

Revisiting the δ Scuti star FG Virginis using Kepler K2 and TESS data

FG Virginis is a δ Scuti variable star that was the target of several ground-based multisite photometric campaigns from 1992 to 2004. Over 75 pulsation frequencies were detected (Breger et al., Astron. Astrophys., 2005, 435, 955–965), more than for any other δ Sct star before the era of space photometry. FG Vir was observed for 52 days in 30-minute cadence photometry by the NASA Kepler spacecraft K2 mission in 2016, and for 23 days in 2-minute cadence photometry by the NASA TESS spacecraft in 2021. We present light curves and amplitude spectra obtained from these space missions. We find around 30 significant frequencies in the K2 data, and more than 100 significant frequencies in the TESS data. There is good correspondence between the first 10 or so highest-amplitude modes found in the K2 and TESS data and those found from the ground-based multisite campaigns, although the amplitude order is slightly different, indicating some stability in mode frequencies and amplitudes spanning 20 years. However, the 9th highest-amplitude mode of Breger et al. has moved down considerably in amplitude rank, while the 35th highest-amplitude mode has moved up to near the top ten as seen in both the K2 and TESS data. We find several low frequencies between 0.3 and 3 cycles per day in the TESS data that were not detected using the ground-based data. If low-frequency pulsations are confirmed, FG Vir would be classified as a δ Sct/γ Dor hybrid variable star. We also review stellar model results and some of the challenges for asteroseismology for this well-studied δ Sct star.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Microwave-Assisted Solution Synthesis of Metastable Intergrowth of AgInS2 Polymorphs

The intergrowth of stable and metastable AgInS2 polymorphs was synthesized using a microwave-assisted synthesis. The samples were synthesized in water and in a deep eutectic solvent (DES) consisting of choline chloride and thiourea. An increase in the metal precursor concentration improved the crystallinity of the synthesized samples and affected the particle size. AgInS2 cannot be synthesized from crystalline binary Ag2S or In2S3 via this route. The solution synthesis reported here results in the intergrowth of the thermodynamically stable polymorph (space group I4¯2d, chalcopyrite structure) and the high-temperature polymorph (space group Pna21, wurtzite-like structure) that is metastable at room temperature. A scanning transmission microscopy (STEM) study revealed the intergrowth of tetragonal and orthorhombic polymorphs in a single particle and unambiguously established that the long-thought hexagonal wurtzite polymorph has pseudo-hexagonal symmetry and is best described with the orthorhombic unit cell. The solution-synthesized AgInS2 polymorphs intergrowth has slightly lower bandgap values in the range of 1.73 eV–1.91 eV compared to the previously reported values for tetragonal I4¯2d (1.86 eV) and orthorhombic Pna21 (1.98 eV) polymorphs.

Adeyemi, Adedoyin N. (ORCID:0000000340096150)↗
DOE OSTI2025

A Region-Growing Segmentation Approach to Delineating Timberline from Satellite-Derived Tree Fractional Cover Products

Timberline marks the transitions from continuous forests to sparse forests and tundra landscapes. As the spatial distribution and dynamics of timberline are closely associated with regional energy and carbon balance, mapping timberline is important to a wide range of environmental and ecological studies. However, current timberline delineation approaches remain under-developed. We proposed an automatic timberline delineation method based on a seeded region-growing segmentation technique and satellite-derived products of tree fractional cover. We applied our approach to the West Siberian Plain and Alaska treeline regions as defined by the Circumpolar Arctic Vegetation Map. The results demonstrate the effectiveness of the proposed method for the accurate delineation of the timberlines that spatially align well with very-high-resolution satellite images. Based on the delineated timberlines, we find regional-scale tree encroachment to be not as substantial as previously reported. The proposed approach can be applied to understanding climate-induced forest responses and inform forest management practices.

Circumpolar Arctic Vegetation Map↗
DOE OSTI2024

First Very Long Baseline Interferometry Detections at 870μm

The first very long baseline interferometry (VLBI) detections at 870$\mu$m wavelength (345$\,$GHz frequency) are reported, achieving the highest diffraction-limited angular resolution yet obtained from the surface of the Earth, and the highest-frequency example of the VLBI technique to date. These include strong detections for multiple sources observed on inter-continental baselines between telescopes in Chile, Hawaii, and Spain, obtained during observations in October 2018. The longest-baseline detections approach 11$\,$G$\lambda$ corresponding to an angular resolution, or fringe spacing, of 19$\mu$as. The Allan deviation of the visibility phase at 870$\mu$m is comparable to that at 1.3$\,$mm on the relevant integration time scales between 2 and 100$\,$s. The detections confirm that the sensitivity and signal chain stability of stations in the Event Horizon Telescope (EHT) array are suitable for VLBI observations at 870$\mu$m. Operation at this short wavelength, combined with anticipated enhancements of the EHT, will lead to a unique high angular resolution instrument for black hole studies, capable of resolving the event horizons of supermassive black holes in both space and time.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗