SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The goal of HYTID was to provide a cost effective hypersonic vehicle constructed of near-state-of art systems and structure with sufficient margins to assure no vehicle flight development problems, and to permit concentration of flight operations on hypersonic research with a broad series of experiments carried in a dedicated payload bay or on the exposed surface of the lower aft fuselage.
Field experiments were conducted to determine how well a seismometer installed using a penetrator would be coupled to the ground. A dry-lake bed and a lava bed were chosen as test sites to represent geological environments of two widely different material properties. At each site, two half-scale penetrators were fired into the ground, a three-component geophone assembly was mounted to the aft end of each penetrator, and dummy penetrators were at various distances to generate seismic signals. These signals were detected by the penetrator-mounted geophone assembly and by a reference geophone assembly buried or anchored to surface rock and 1-m from the penetrator. The recorded signals were digitized, and cross-spectral analyses were performed to compare the observed signals in terms of power spectral density ratio, coherence, and phase difference. The analyses indicate that seismometers deployed by penetrators will be as well coupled to the ground as are seismometers installed by conventional methods for the frequency range of interest in earthquake seismology.
An investigation was conducted in the NASA-Ames 40 by 80 Foot Wind Tunnel to determine the aerodynamic characteristics of a large scale, VTOL, lift fan, jet transport model. The model had two lift fans at the forward portion of the fuselage, a lift fan at each wing tip, and two lift/cruise fans at the aft portion of the fuselage. All fans were driven by tip turbines using T-58 gas generators. Results were obtained for several lift fan, exit vane deflections and lift/cruise fan thrust deflections are zero sideslip. Three component longitudinal data are presented at several fan tip speed ratios. A limited amount of six component data were obtained with asymmetric vane settings. All of the data were obtained without a horizontal tail. Downwash angles at a typical tail location are also presented.
The sound field due to a propeller operating at supersonic tip speed in a uniform flow was investigated. Using the fact that the wave front in a uniform stream is a convected sphere, the fundamental solution to the convected wave equation was easily obtained. The Fourier coefficients of the pressure signature were obtained by a far field approximation, and are expressed as an integral over the blade platform. It is shown that cones of silence exist fore and aft the propeller plane. The semiapex angles are shown. These angles are independent of the individual Mach components such as the flight Mach number and the rotation Mach number. The result is confirmed by the computation of the ray path of the emitted Mach waves. The Doppler amplification factor strengthens the signal behind the propeller while it weakens that upstream.
A hydrazine fueled piston engine for providing 11.2 kW was developed to satisfy the need for an efficient power supply in the range from 3.7 to 74.6 kW where existing nonair-breathing power supplies such as fuel cells or turbines are inappropriate. The engine was developed for an aircraft to fly to 21.3 km and above and cruise for extended periods. A remotely piloted aircraft and the associated flight control techniques for this application were designed. The engine is geared down internally (2:1) to accommodate a 1.8 m diameter propeller. An alternator is included to provide electrical power. The pusher-type engine is mounted onto the aft closure of the fuel tank, which also provides mounting for all other propulsion equipment. About 20 hrs of run time demonstrated good efficiency and adequate life. One flight test to 6.1 km was made using the engine with a small fixed-pitch four-bladed propeller. The test was successful in demonstrating operational characteristics and future potential.
ASALM (Advanced Strategic Air-Launched Missile) is a supersonic air vehicle designed to be air-launched from a carrier aircraft. The four aft aerodynamic control vanes are folded to maximize the number of missiles carried on-board. The unfolding (erection) system must be small, energetic, fast, and strong. The materials selected and problems that arose during development of the unfolding system are described.
Wind-tunnel tests were conducted to evaluate the effects on performance of modifying a 13-percent-thick low-speed airfoil. The airfoil contour was altered to reduce the aft upper surface pressure gradient and hence delay boundary layer separation at typical lift coefficients for light general aviation airplanes. The tests were conducted at a Mach number of 0.15 or less over a Reynolds number range from about 1,000,000 to 9,000,000.
Predictions made with NASA's aircraft noise prediction program (ANOPP) were compared with flyover noise data. A data base of six flyover noise runs for the DC-10-40/JT9D-59A configuration was used. For all power settings, ANOPP consistently underpredicted the low frequency spectral levels, overpredicted high frequency spectral levels and, consequently, overpredicted the inlet and aft PNLT time histories.
Wind tunnel tests were conducted to examine various aspects of the drooped-leading edge airfoil which reduces the tendency for an airplane to enter a spin after stall occurs. Three baseline models were used for tests of two dimensional models: NACA 0015, 0014.6, and 0014.2. The 14.6% and 14.2% models were derived from NACA 0015 sections by increasing the chord and matching the profiles aft section. Force, balance data (lift, drag, pitching moment) were obtained for each model at a free-steam Reynold's number of 2.66 x 10 to the 6th power/m. In addition, oil flow visualization tests were performed at various angles of attack. An existing NACA 64 sub 1 A211 airfoil was used in a second series of tests. The leading edge flap was segmented in three parts which allowed various baseline/drooped leading edge configurations to be tested. Force balance and flow visualization tests were completer at chord Renolds numbers of 0.44 x 10 to the 6th power, 1.4 x 10 to the 6th power, and 2.11 x 10 to the 6th power. Test results are included.
Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after five years' service. There are six Kevlar-49 panels on each aircraft: a left-hand and right-hand set of a wing-body sandwich fairing; a solid laminate under-wing fillet panel; and a 150 C (300 F) service aft engine fairing. The fairings have accumulated a total of 40,534 hours, with one ship set having 16,091 hours service as of Feb. 11, 1979. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings.
The characteristics were determined of a lift cruise fan V/STOL multi-mission configuration in the near proximity to the edge of a small flat surface representation of a ship deck. Tests were conducted at both static and forward speed test conditions. The model (0.12 scale) tested was a four fan configuration with modifications to represent a three fan configuration. Analysis of data showed that the deck edge effects were in general less critical in terms of differences from free air than a full deck (in ground effect) configuration. The one exception to this was when the aft edge of the deck was located under the center of gravity. This condition, representative of an approach from the rear, showed a significant lift loss. Induced moments were generally small compared to the single axis control power requirements, but will likely add to the pilot work load.
The aerodynamic characteristics of the augmentor wing concept with hypermixing primary nozzles were investigated. A large-scale semispan model in the Ames 40- by 80-Foot Wind Tunnel and Static Test Facility was used. The trailing edge, augmentor flap system occupied 65% of the span and consisted of two fixed pivot flaps. The nozzle system consisted of hypermixing, lobe primary nozzles, and BLC slot nozzles at the forward inlet, both sides and ends of the throat, and at the aft flap. The entire wing leading edge was fitted with a 10% chord slat and a blowing slot. Outboard of the flap was a blown aileron. The model was tested statically and at forward speed. Primary parameters and their ranges included angle of attack from -12 to 32 degrees, flap angles of 20, 30, 45, 60 and 70 degrees, and deflection and diffuser area ratios from 1.16 to 2.22. Thrust coefficients ranged from 0 to 2.73, while nozzle pressure ratios varied from 1.0 to 2.34. Reynolds number per foot varied from 0 to 1.4 million. Analysis of the data indicated a maximum static, gross augmentation of 1.53 at a flap angle of 45 degrees. Analysis also indicated that the configuration was an efficient powered lift device and that the net thrust was comparable with augmentor wings of similar static performance. Performance at forward speed was best at a diffuser area ratio of 1.37.
Tabulated surface pressure data for a series of four forebodies which have analytically defined cross sections and which are based on a parabolic arc profile having a 20 deg half angle at the nose are presented without analysis. The first forebody has a circular cross section, and the second has a cross section which is an ellipse with an axis ratio of 2/1. The third has a cross section defined by a lobed analytic curve. The fourth forebody has cross sections which develop smoothly from circular at the pointed nose through the lobed analytic curve and back to circular at the aft end. The data generally cover angles of attack from -5 deg to 20 deg at angles of sideslip from 0 deg to 5 deg for Mach numbers of 1.70, 2.50, 3.95, and 4.50 at a constant Reynolds number.
An analysis of pressure and strain-gage data from space shuttle wind tunnel test IA119 and IA138 was performed to define the influence on aerodynamic characteristics resulting from the main propulsion system and solid rocket booster plumes. Aerodynamic characteristics of each of the elements, the components and total vehicle of the space shuttle vehicle during ascent flight was considered. Pressure data were obtained over the aft portions of the space shuttle wind tunnel model in addition to wing and elevon gage data.
The CASTS Project initiated to develop graphite fiber/polyimide matrix (GR/PI) composite structures with 589K operational capability for aerospace vehicles is described. Near term tasks include screening composites and adhesives for 589K service, developing fabrication procedures and specifications, developing design allowables test methods and data, design and test of structural elements, and construction of a full scale aft body flap for the space shuttle orbiter vehicle for ground testing. Far term tasks include research efforts directed at new materials, manufacturing procedures and design/analysis methodology. Specific results discussed include: (1) identification of four GR/PI composites and three PI adhesives with 589K service potential for periods ranging from 125 to 500 hours; (2) development of an adhesive formulation suitable for bonding reusable surface insulation (RSI) titles to 589K (GR/PI) substructure; (3) the capability to fabricate and nondestructively inspect laminates, hat section shaped stiffeners, honeycomb sandwich panels, and chopped fiber moldings; and (4) test methods for measuring design allowables at 117K.
The aircraft noise prediction program (ANOPP) was used to predict the far-field noise characteristics of an L-1011 aircraft equipped with RB.211-524B engines. Actual flight noise was compared with noise predicted for the same operating and weather conditions. Correlation of predicted and measured results was very good in the aft quadrant of radiated noise. Predicted noise levels were significantly different from measured values in the forward quadrant because fan noise was predicted high. Since the major noise sources were fan and core, corrections are supplied to adjust ANOPP fan and core noise components so that the total predicted noise matches the measured L-1011 noise levels.
A Shuttle-borne tether system capable of deploying a tether to radial distances as great as 100 km was described by Rupp and Laue (1978). The system as discussed by Rupp and Laue would have a total mass of 700 kg and would be mounted on one Shuttle pallet. It would consist of a tether reel mechanism complete with a servo drive motor and control sensors, a boom with docking probe used for initial deployment and subsequent retrieval, some type of satellite weighing 175 kg, up to 100 km of synthetic or metallic tether approximately 1 mm in diameter, a digital control computer, and a control and display panel on the Orbiter aft flight deck for crew operation. The primary use of a tether system for geological applications would be in the measurement of those magnetic and gravitational fields associated with geological structures. The major appeal in connection with atmospheric applications is the system's ability to extend instrumentation down into the lower thermosphere and possibly the mesosphere.
Effects of elevon-induced three-dimensional shock-wave turbulent boundary-layer interactions on hypersonic aircraft surfaces are analyzed. Detailed surface pressure and heating rate distributions obtained on wing-elevon-fuselage models representative of aft portions of hypersonic aircraft are compared with analytical and experimental results from other sources. Examples are presented that may be used to evaluate the adequacy of current theoretical methods for estimating the effects of three-dimensional shock-wave turbulent boundary-layer interactions on hypersonic aircraft surfaces.