Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

A novel methodology for assessing the hygroscopicity of aerosol filter samples

Abstract. Due to US regulations, concentrations of hygroscopic inorganic sulfate and nitrate have declined in recent years, leading to an increased importance of the hygroscopic nature of organic matter (OM). The hygroscopicity of OM is poorly characterized because only a fraction of the multitude of organic compounds in the atmosphere is readily measured, and there is limited information on their hygroscopic behaviors. Hygroscopicity of aerosol is traditionally measured using a humidified tandem differential mobility analyzer (HTDMA) or electrodynamic balance (EDB). EDB measures water uptake by a single particle. For ambient and chamber studies, HTDMA measurements provide water uptake and particle size information but not chemical composition. To fill this information gap, we developed a novel methodology to assess the water uptake by particles collected on Teflon filters. This method uses the same filter sample for both hygroscopicity measurements and chemical characterization, thereby providing an opportunity to link the measured hygroscopicity with ambient particle composition. To test the method, hygroscopic measurements were conducted in the laboratory for ammonium sulfate, sodium chloride, glucose, and malonic acid, which were collected on 25 mm Teflon filters using an aerosol generator and sampler. Constant-humidity solutions (CHSs), including potassium chloride, barium chloride dihydrate, and potassium sulfate, were employed in a saturated form to maintain the relative humidity (RH) at approximately 84 %, 90 %, and 97 % in small chambers. Our preliminary experiments revealed that, without the pouch, water uptake measurements were not feasible due to rapid water loss during weighing. Additionally, we observed some absorption by the aluminum pouch itself. To account for this, concurrent measurements were conducted for both the loaded and the blank filters at each RH level. Thus, the dry loaded and blank Teflon filters were placed in aluminum pouches with one side open and in RH-controlled chambers for more than 24 h. The wet loaded samples and wet blanks were then weighed using an ultramicrobalance to determine the water uptake by the respective compound and the blank Teflon filter. The net amount of water absorbed by each compound was calculated by subtracting the water uptake of the blank filter from that of the wet loaded filter. Hygroscopic parameters, including the water-to-solute (W / S) ratio, molality, mass fraction solute (mfs), and growth factors (GFs), were calculated from the measurements. The results obtained are consistent with those reported by the Extended Aerosol Inorganics Model (E-AIM) and previous studies utilizing HTDMA and EDB for these compounds, highlighting the accuracy of this new methodology. This new approach enables the hygroscopicity and chemical composition of individual filter samples to be assessed so that in complex mixtures, such as chamber and ambient samples, the total water uptake can be parsed between the inorganic and organic components of the aerosol.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1973

Investigation of use of space data in watershed hydrology

The author has identified the following significant results. Ground truth data have been compiled and 256 rainfall runoff events have been used to detemine coefficients for two storm runoff equations that apply to the 20 study watersheds. Two scenes have been processed using CCT data. Data pertinent to each of the study watersheds have been excerpted from the tapes. A computer program and display technique has been developed to retrieve the data from irregular shaped areas and store it in a format that allows future display of only the area desired. Means, standard deviations, and distributions have been determined for extreme dry and extreme wet conditions in the dormant season. Mean digital values show some variation between watersheds when dry, but no significant differences when wet. Standard deviations of digital values diminish drastically under wet dormant conditions. Thus the standard deviations may be a good indicator of influence of moisture. Distributions of seven bit values show that odd numbers are prevalent and irregular distribution may influence some classification schemes now in use.

Blanchard, B.↗
NASA NTRS1973

Microfog lubricant application system for advanced turbine engine components, phase 3

The wetting characteristics and deposit forming tendencies of a series of lubricants were evaluated using a microfog jet delivery system to wet a flat heated rotating disc. The performances of the nine lubricants are discussed in terms of the various testing parameters which include temperature, disc speed and lubricant gas flow rates. Also discussed are the heat transfer characteristics of two of the lubricants on that same plane disc specimen. The wetting characteristics and heat transfer characteristics of one of the lubricants on a complex disc simulating bearing geometry are also discussed.

Petrucco, R. J.↗
NASA NTRS1975

Space processing of composite materials

Materials and processes for the testing of aluminum-base fiber and particle composites, and of metal foams under extended-time low-g conditions were investigated. A wetting and dispersion technique was developed, based on the theory that under the absence of a gas phase all solids are wetted by liquids. The process is characterized by a high vacuum environment and a high temperature cycle. Successful wetting and dispersion experiments were carried out with sapphire fibers, whiskers and particles, and with fibers of silicon carbide, pyrolytic graphite and tungsten. The developed process and facilities permit the preparation of a precomposite which serves as sample material for flight experiments. Low-g processing consists then merely in the uniform redistribution of the reinforcements during a melting cycle. For the preparation of metal foams, gas generation by means of a thermally decomposing compound was found most adaptable to flight experiments. For flight experiments, the use of compacted mixture of the component materials limits low-g processing to a simple melt cycle.

Steurer, W. H.↗
NASA NTRS1974

Space-related composite-material experiments

The preparation of composites in space depends on the immersion of reinforcements in a liquid-metal matrix and their uniform, stable dispersion in the bulk products until solidification occurs. The chief problem in achieving the composite is associated with the 'wetting' of the reinforcements. A study of the theory of wetting revealed that wetting is prevented by the presence of gaseous and oxide contaminants at the interface between the pure liquid and pure solid. Experiment then confirmed that the use of a vacuum environment, cleaning of all surfaces, elevated temperature, ion bombardment, and vigorous mechanical agitation enabled the immersion and dispersion of candidate reinforcements. The technique is limited by the increased tendency for reaction if the time at elevated temperature is extended.

Kaye, S.↗
NASA NTRS1977

Process for preparing liquid metal electrical contact device

The parts of an electrical contact device are treated by sputter etching to remove the parent metal oxide. Prior to exposure of the electrodes to any oxygen, a sacrificial metal is sputter deposited on the parts. Preferably this sacrificial metal is one that oxidizes slowly and is readily dissolved by the liquid metal. The sacrificial metal may then be removed from unwanted areas. The remainder of the ring and the probe to be wet by the liquid metal are submerged in the liquid metal or the liquid metal is flushed over these areas, preferably while they are being slightly abraded, unitl all the sacrificial material on these portions is wet by the liquid metal. In doing so the liquid metal dissolves the sacrificial metal and permanently wets the parent metal. Preferred materials used in the process and for the electrodes of electrical contact devices are high purity (99.0%) nickel or AISI type 304 stainless steel for the electrical contact devices, gallium as the liquid metal, and gold as the sacrificial material.

Lovell, R. R.↗
NASA NTRS1977

Friction characteristics of three 30 by 11.5-14.5, type 8, aircraft tires with various tread groove patterns and rubber compounds

A test program was conducted to evaluate friction performance and wear characteristics on wet runways of three 30 x 11.5-14.5, type, aircraft tires having two different tread patterns and natural rubber contents. All test tires had the standard three circumferential groove tread, but two had molded transverse grooves which extended from shoulder to shoulder. The tread rubber content of the two tires with transverse grooves differed in that one had a 100 percent natural rubber tread and the other had a rubber tread composition that was 30 percent synthetic and 70 percent natural. The third test tire had the conventional 100 percent natural rubber tread. Results indicate that the differences in tire tread design and rubber composition do not significantly affect braking and cornering friction capability on wet or dry surfaces. Braking performance of the tires decreases with increased speed, with increased yaw angle and, at higher speeds, with increased wetness of the surface.

Yager, T. J.↗
NASA NTRS1978

Study of low-cost fabrication methods for aerospace composite materials

Flat and hat section specimens of graphite/epoxy composite materials have been fabricated by the resin bath or wet pultrusion process. This demonstrated the feasibility of incorporating crossplied graphite fiber reinforcements in conjunction with epoxy resin systems in the wet pultrusion process. However, the thickness constraints of the pultrusion process, the lack of dimensional stability of the crossply materials and equipment limitations affect the quality of the hat section pultrusions. The wet pultrusion process shows promise of being a low cost method for producing composite parts with constant cross section along the length. A cost analysis showed at least 80 percent cost reduction for the hat section and 40 percent for flat panel by pultrusion over the conventional manual and automated lay-up.

Chung, H. H.↗
NASA NTRS1978

Parametric modeling of low-frequency water-vapor-induced tropospheric path length fluctuations

Detailed wet tropospheric fluctuation information is presented in support of proposals to search for gravitational waves in ultra-precise Doppler data. The similarities between the solar wind and tropospheric effects on apparent signal path length are used to hypothesize a parametric model for low-frequency wet tropospheric path length fluctuation. Experimental observations of wet tropospheric signal delay fluctuations are interpreted as confirmation of this parametric form. The model is used to suggest the appropriate conditions for collection of experimental tropospheric fluctuation data.

Berman, A. L.↗
NASA NTRS1980

The enhanced oxidation of SO2 by NO2 on carbon particulates

The oxidation of SO2 on carbon particles in dry air and in air at 65% relative humidity (RH) was found to be greatly enhanced by the presence of gaseous NO2. Exposures of 20-80ppm SO2 + 10ppm NO2 on 1-mg samples of commercial carbon black were found to produce both sorption and desorption coverages (weight retained after desorption into N2) of over one order of magnitude greater than for corresponding SO2 exposures. Significant agglomeration and wetting were observed to occur progressively during exposures at 65% RH, and samples, even after 150-h exposure, rarely reached steady-state weight gain. The wetting may have regenerated fresh reactive carbon surface. Sorptions conducted in nitrogen atmospheres, rather than in air, appeared to produce slightly higher sorptions and weight retentions for equivalent exposure concentrations and times, indicating that NO2 served as the oxidizer and that molecular oxygen, or some trace constitutents in air, may have weakly inhibited the oxidation by NO2. Wet chemical analysis of the desorbed phase indicated that sulfate, presumably H2SO4 accounted for over half of the retained weight. Measurements of pH from water-quenched samples indicated a highly acidic surface phase, and suggested the oxidation process could proceed in an acidic environment.

Cofer, W. R., III↗
NASA NTRS1980

The evaluation of evaporation by infrared thermography: A critical analysis of the measurements on the Crau test site

Evapotranspiration was calculated for both the dry and irrigated zone by four methods which were compared with the energy balance method serving as a reference. Two methods did not involve the surface temperature. They are ETR(n) = R(n), liable to be valid under wet conditions and ET(eq) = (delta/delta + gamma) R(n) i.e, the first term of Penman's equation, adapted to moderately dry conditions. The methods using surface temperature were the combined energy balance aerodynamic approach and a simplified approach proposed by Jackson et al. Tests show the surface temperature methods give relatively satisfactory results both in the dry and wet zone, with a precision of 10% to 15% compared with the reference method. As was to be expected, ET(eq) gave satisfactory results only in the dry zone and ET(Rn) in the irrigated zone. Thermography increased the precision in the estimate of ET relative to the most suitable classical method by 5% to 8% and is equally suitable for both dry and wet conditions. The Jackson method does not require extensive ground measurements and the evaluation of the surface roughness.

Seguin, B.↗
NASA NTRS1980

Microwave radiometric observations of snowpacks

Models for the microwave emission from snowpacks were generated on the basis of radiometric observations made at 10.7 GHz, 37 HGz, and 94 GHz at a test site near Steamboat Springs, Colorado. In addition to conducting measurements on an approximately daily basis over a six week observation period, measurements were made over several diurnal cycles during which the change in snow wetness was tracked by the microwave radiometers. Also, the variation in emissivity with snow water equivalent was examined, as was the sensitivity to changes in snow surface geometry. The microwave emissivity was observed to (1) decrease exponentially with snow water equivalent and (2) increase with snow wetness. Thus, the emission behavior is the reverse of the backscattering behavior observed by the radar. By fitting the models to the measured data, the variation of the optical depth with snow wetness was estimated.

Ulaby, F. T.↗
NASA NTRS1981

Modulus, strength and thermal exposure studies of FP-Al2O3/aluminum and FP-Al2O3/magnesium composites

The mechanical properties of FP-Al2O3 fiber reinforced composites prepared by liquid infiltration techniques are improved. A strengthening addition, magnesium, was incorporated with the aluminum-lithium matrix alloy usually selected for these composites because of its good wetting characteristics. This ternary composite, FP-Al2O3/Al-(2-3)Li-(3-5)Mg, showed improved transverse strength compared with FP-Al2O3/Al-(2-3)Li composites. The lower axial strengths found for the FP-Al2O3/Al-(2-3)Li-(3-5)Mg composites were attributed to fabrication related defects. Another technique was the use of Ti/B coated FP-Al2O3 fibers in the composites. This coating is readily wet by molten aluminum and permitted the use of more conventional aluminum alloys in the composites. However, the anticipated improvements in the axial and transverse strengths were not obtained due to poor bonding between the fiber coating and the matrix. A third approach studied to improve the strengths of FP-Al2O3 reinforced composites was the use of magnesium alloys as matrix materials. While these alloys wet fibers satisfactorily, the result indicated that the magnesium alloy composites used offered no axial strength or modulus advantage over FP-Al2O3/Al-(2-3)Li composites.

Bhatt, R. T.↗
NASA NTRS1982

Solidification studies of monotectic systems

Described is an attempt to determine critical wetting temperatures in monotectic systems and to investigate the wetting phase on container walls and the phase preferential wetting of a monotectic solid.

Chang, K.↗
NASA NTRS1983

Factors influencing aircraft ground handling performance

Problems associated with aircraft ground handling operations on wet runways are discussed and major factors which influence tire/runway braking and cornering traction capability are identified including runway characteristics, tire hydroplaning, brake system anomalies, and pilot inputs. Research results from tests with instrumented ground vehicles and aircraft, and aircraft wet runway accident investigation are summarized to indicate the effects of different aircraft, tire, and runway parameters. Several promising means are described for improving tire/runway water drainage capability, brake system efficiency, and pilot training to help optimize aircraft traction performance on wet runways.

Yager, T. J.↗
NASA NTRS1983

The utilization of Nimbus-7 SMMR measurements to delineate rainfall over land

Approaches for developing an improved passive microwave technique to delineate rain from wet land surfaces are considered, and an investigation is conducted with the objective to study the application of these ideas with empirical data. The investigation includes a statistical analysis of Nimbus-7 Scanning Multichannel Microwave Radiometer (SMMR) 37.0, 18.0, and 10.7 GHz data. The possibility was assessed to make use of the 18.0 and 10.7 GHz channels in order to reduce the ambiguities found in the 37.0 GHz radiometer data for differentiating rainfall areas from wet land surfaces. It was found, however, that none of the SMMR channels could differentiate rain from wet or dry land when surface temperatures were less than 15 C. It appears that an improved rainfall-over-land detection technique could be developed by two different methods, utilizing both satellite infrared and multifrequency dual polarized passive microwave data.

Rodgers, E.↗
NASA NTRS1986

Surface effects on phase distributions of a fast-quenched miscibility gap type system - Succinonitrile-water

If a binary homogeneous melt is cooled into an immiscible region, the newly formed second phase will generally have a density different from the parent phase, and will separate readily by sedimentation. Observation of solidification processes in microgravity indicates that outside of sedimentation, at least two other important effets can separate the phases: (1) preferential wetting, and (2) thermal migration of second-phase droplets due to interfacial tension gradients. The latter effect would drive the minority phase along the thermal gradient toward the hottest part (assuming the interfacial tension decreases with increasing temperature), which is usually away from the crucible wall. On the other hand, if the minority phase preferentially wets the crucible, a minority phase layer which thickens as initial solution compositions approach critical, will form adjacent to the solid surface and remain in the coldest region of the ingot. This study presents compelling preliminary evidence that these two effects do exist and that they compete with one another. However, the temperature dependence of preferential wetting below T(c) for the current system of study is, as yet, undetermined. These effects are sensitive to the initial concentration of a hypermonotectic solution cooling through a miscibility gap.

Frazier, D. O.↗
NASA NTRS1987

The effect of Tricresyl-Phosphate (TCP) as an additive on wear of Iron (Fe)

The effect of tricresyl phosphate (TCP) as an antiwear additive in lubricant trimethyol propane triheptanoate (TMPTH) was investigated. The objective was to examine step loading wear by use of surface analysis, wetting, and chemical bonding changes in the lubricant. The investigation consisted of steploading wear studies by a pin or disk tribometer, the effects on wear related to wetting by contact angle and surface tension measurements of various liquid systems, the chemical bonding changes between lubricant and TCP chromatographic analysis, and by determining the reaction between the TCP and metal surfaces through wear scar analysis by Auger emission spectroscopy (AES). The steploading curve for the base fluid alone shows rapid increase of wear rate with load. The steploading curve for the base fluid in presence of 4.25 percent by volume TCP under dry air purge has shown a great reduction of wear rate with all loads studied. It has also been found that the addition of 4.25 percent by volume TCP plus 0.33 percent by volume water to the base lubricant under N2 purge also greatly reduces the wear rate with all loads studied. AES surface analysis reveals a phosphate type wear resistant film, which greatly increases load-bearing capacity, formed on the iron disk. Preliminary chromatographic studies suggest that this film forms either because of ester oxidation or TCP degradation. Wetting studies show direct correlation between the spreading coefficient and the wear rate.

Ghose, Hiren M.↗