SEARCH · Engineering Papers

Results for “viscoelasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Stiffness reductions during tensile fatigue testing of graphite/epoxy angle-ply laminates

Tensile fatigue data was generated under carefully controlled test conditions. A computerized data acquisition system was used to permit the measurement of dynamic modulus without interrupting the fatigue cycling. Two different 8-ply laminate configurations, viz, + or - 45 (2s) and + or - 67.5 (2s), of a T300/5208 graphite/epoxy composite were tested. The + or - 45 (2s) laminate did exhibit some modulus decay, although there was no well-defined correlation with applied stress level or number of cycles. The + or - 67.5 (2s) laminate did not exhibit any measurable modulus decay. Secondary effects observed included a small but distinct difference between modulus as measured statically and dynamically, a slight recovery of the modulus decay after a test interruption, and a significant viscoelastic (creep) response of the + or - 45 (2s) laminate during fatigue testing.

Odom, E. M.↗

NASA NTRS1983

Material characterization of structural adhesives in the lap shear mode

A general method for characterizing structual adhesives in the bonded lap shear mode is proposed. Two approaches in the form of semiempirical and theoretical approaches are used. The semiempirical approach includes Ludwik's and Zhurkov's equations to describe respectively, the failure stresses in the constant strain rate and constant stress loading modes with the inclusion of the temperature effects. The theoretical approach is used to describe adhesive shear stress-strain behavior with the use of viscoelastic or nonlinear elastic constitutive equations. Two different model adhesives are used in the single lap shear mode with titanium adherends. These adhesives (one of which was developed at NASA Langley Research Center) are currently considered by NASA for possible aerospace applications. Use of different model adhesives helps in assessment of the generality of the method.

Sancaktar, E.↗

NASA NTRS1980

An experimental investigation of noise attenuating techniques for space-shuttle canisters

A model of the space shuttle thermal canister was acoustically tested to determine the amount of noise attenuation which could be derived using a simple, single-wall canister construction having rectangular shape. Acoustic testing was performed on the basic canister and with noise-attenuating design modifications. The basic canister experienced noise amplifications at 56 and 80 Hz, which are attributed to the fundamental canister acoustic mode and local panel structural resonances, respectively. The standing wave response at 56 Hz was effectively suppressed by the incorporation of a cardboard baffle midway between the canister end-caps (an additional overall noise reduction of 4 dB). The canister was next tested with 14%, 22.5% and 31% sound absorptive coverages on the interior walls. The coverage was effective between 400-3000 Hz; the maximum benefit (9 dB) occurring at 1600 Hz. Viscoelastic damping strips bonded to the canister exterior provided an additional 4 to 5 dB attenuation over much of the frequency range and has an overall reduction of about 10 dB as compared to 4.4 dB without damping. A significant reduction of the resonant effect at 80 Hz was noted.

Mirandy, L.↗

NASA NTRS1983

Vertical movements following a dip-slip earthquake

The results of finite element (FEM) computations based on elastic dislocation theory are presented. It is shown that the ratio of fault depth to the lithospheric thickness is a significant factor in the sign of the rebound. Subsidence occurs if the fault penetrates less than approximately 0.68 of the way through the lithosphere. An uplift occurs if the fault cuts deeper. The FEM employed consisted of a 546 node, 500 element grid and a quasi-plane strain algorithm. The situation modeled consisted of a 30 deg dip fault in an initially planar elastic lithosphere overlying a Maxwell viscoelastic asthenosphere. It is suggested that postseismic rebound may be measurable over a several year interval, thus providing data on lithosphere thicknesses.

Melosh, H. J.↗

NASA NTRS1982

The evolution of tectonic features on Ganymede

The bands of bright resurfaced terrain on Ganymede are probably broad grabens formed by global expansion and filled with deposits of ice. Grooves within the bands are thought to be extensional features formed during the same episode of expansion. The crust of Ganymede is modeled as a viscoelastic material subjected to extensional strain. With sufficiently high strain rates and stresses, deep normal faulting will occur, creating broad grabens that may then be filled. Continuing deformation at high strain rates and stresses will cause propagation of deep faults up into the flood deposits and normal faulting at the surface, while lower strain rates and stresses will cause formation of open extension fractures or, if the crustal strength is very low, grabens at the surface. The spacing between adjacent fractures may reflect the geothermal gradient at the time of deformation. Surface topography resulting from fracturing and normal faulting will decay with time as a result of viscous relaxation and mass-wasting.

Squyres, S. W.↗

NASA NTRS1983

Dynamic-mechanical response of graphite/epoxy composite laminates and neat resin

Dynamic mechanical measurement results are presented for the case of carbon fiber-reinforced, epoxy matrix composite laminates subjected to loading perpendicular to the lamination plane, as well as for neat epoxy resin under the same conditions, where temperatures ranged between 20 and 200 C and deformation levels lie within the linear viscoelastic region. In-phase and out-of-phase stiffnesses are found to become superposed, forming master curves that cover a 12-decade frequency range. The application of a master curve scaling procedure shows that the in-phase stiffness has the same shape, and out-of-phase stiffness has the same dispersion, for all laminates irrespective of stacking sequence and are, in turn, nearly identical to those for the neat epoxy resin. An empirical function is found for the relaxation modulus which, when converted to a dynamic modulus, yields good overall agreement for both of the dynamic stiffness components as a function of frequency.

Yang, P.↗

NASA NTRS1983

Acoustic emission characterization using AE (parameter) delay

The acoustic emission (AE) parameter delay concept is defined as that particular measured value of a parameter at which a specified baseline level of cumulative AE activity is reached. The parameter can be from any of a broad range of elastic, plastic, viscoelastic, and fracture mechanics parameters, as well as their combinations. Such parameters include stress, load, strain, displacement, time, temperature, loading cycle, unloading stress, stress intensity factor, strain energy release rate, and crack tip plasticity zone size, while the AE activity may be AE event counts, ringdown counts, energy, event duration, etc., as well as their combinations. Attention is given to examples for the AE parameter delay concept, together with various correlations.

Williams, J. H., Jr.↗

NASA NTRS1983

Material characterization of structural adhesives in the lap shear mode

A general method for characterizing structural adhesives in the bonded lap shear mode is proposed. Two approaches in the form of semi-empirical and theoretical approaches are used. The semi-empirical approach includes Ludwik's and Zhurkov's equations to describe respectively, the failure stresses in the constant strain rate and constant stress loading modes with the inclusion of the temperature effects. The theoretical approach is used to describe adhesive shear stress-strain behavior with the use of viscoelastic or nonlinear elastic constitutive equations. Three different model adhesives are used in the simple lap shear mode with titanium adherends. These adhesives (one of which was developed at NASA Langley Research Center) are currently considered by NASA for possible aerospace applications. Use of different model adhesives helps in assessment of the generality of the method.

Schenck, S. C.↗

NASA NTRS1983

Study of noise transmission through double wall aircraft windows

Analytical and experimental procedures were used to predict the noise transmitted through double wall windows into the cabin of a twin-engine G/A aircraft. The analytical model was applied to optimize cabin noise through parametric variation of the structural and acoustic parameters. The parametric study includes mass addition, increase in plexiglass thickness, decrease in window size, increase in window cavity depth, depressurization of the space between the two window plates, replacement of the air cavity with a transparent viscoelastic material, change in stiffness of the plexiglass material, and different absorptive materials for the interior walls of the cabin. It was found that increasing the exterior plexiglass thickness and/or decreasing the total window size could achieve the proper amount of noise reduction for this aircraft. The total added weight to the aircraft is then about 25 lbs.

Vaicaitis, R.↗

NASA NTRS1984

Investigation of articulated panel dynamics

An articulated panel dynamics experiment to evaluate present analysis and ground test methods as well as damping effectiveness is proposed. The experiment uses an existing panel design which was extensively analyzed and tested. These data provide a firm basis for evaluating the adequacy of panel analysis and ground test methodology. The key issues for future large space structure panel designs are addressed: the critical launch transient and vibroacoustic loading; the deployment analysis adequacy including air and gravitational effects; and the orbital resonant frequencies and mode shapes of deployed panel assemblies. By using an existing mature design that was thoroughly tested, the effort can focus on correlation of actual flight results with existing predictions. A second panel assembly incorporating passive damping is proposed to provide a direct measure of damped panel benefits that can be obtained. These benefits include: reduced launch loads and responses; and highly damped deployed modes. Existing space-qualified viscoelastic epoxy, in combination with composite materials or an alternate more effective damping material, will be used.

Stahle, C. V., Jr.↗

NASA NTRS1983

A numerical procedure for predicting creep and delayed failures in laminated composites

A numerical procedure is described for predicting the viscoelastic response of general laminates. A nonlinear compliance model is used to predict the creep response of the individual laminae. A biaxial delayed failure model predicts ply failure. The numerical procedure, based on lamination theory, increases by increments through time to predict creep compliance and delayed failures in laminates. Numerical stability problems and experimental verification are discussed. Although the program has been quite successful in predicting creep of general laminates, the assumptions associated with lamination theory have resulted in erroneous bounds on the predicted material response. Delayed failure predictions have been conservative. Several improvements are suggested to increase the accuracy of the procedure.

Dillard, D. A.↗

NASA NTRS1984

Hygrothermal effects on stresses and deformations in a bonded fiber-reinforced plastic/aluminum system

The hygrothermal effect on time dependent mechanical behavior of a model of nonsymmetrical bonded fiber-reinforced plastic (FRP)/aluminum system was investigated analytically. It was found that a linear viscoelastic closed form solution is sufficient for the prediction model deformations for short periods of time and small strains, while a numerical finite-element solution is preferable for determining adhesive stresses and deformational behavior of the model at any time. The thermoelastic numerical solution shows a certain decrease with time of adhesive stresses, which does not seem to affect significantly the global deformations of the model. On the other hand, it was found that the presence of moisture within the polymeric adhesive layer causes significant decrease in adhesive stresses, which affects deformational changes with time, far beyond the level predicted by the static solution.

Yaniv, G.↗

NASA NTRS1984

Deformations and strains in adhesive joints by moire interferometry

Displacement fields in a thick adherend lap joint and a cracked lap shear specimen were measured by high sensitivity moire interferometry. Contour maps of in-plane U and V displacements were obtained across adhesive and adherent surfaces. Loading sequences ranged from modest loads to near-failure loads. Quantitative results are given for displacements and certain strains in the adhesive and along the adhesive/adherend boundary lines. The results show nonlinear displacements and strains as a function of loads or stresses and they show viscoelastic or time-dependent response. Moire interferometry is an excellent method for experimental studies of adhesive joint performance. Subwavelength displacement resolution of a few micro-inches, and spatial resolution corresponding to 1600 fringes/inch (64 fringes/mm), were obtained in these studies. The whole-field contour maps offer insights not available from local measurements made by high sensitivity gages.

Post, D.↗

NASA NTRS1985

Passive and Active Control of Space Structures (PACOSS)

Passive and Active Control of Space Structures (PACOSS) is a five-year program designed to investigate highly damped structures in conjunction with active control systems, and in particular to develop technology that integrates passive damping and active control to achieve precise pointing control. Major areas of research include metal matrix composites; viscoelastic materials; damping devices; dynamic test article design, fabrication and testing; and active damping.

Morosow, G.↗

NASA NTRS1983

A thin film strain transducer

A device has been developed for the purpose of measuring longitudinal strain in thin polyethylene films. This paper describes the design, development, calibration, and application of this unique transducer in a variety of low temperature environments. This thin, ring-shaped device has a low effective modulus so as not to interfere with the strain that would naturally occur in a thin film. It has a standard 350 ohm impedance which is compatible with most available bridge balance, amplification, and telemetry instrumentation. This transducer has been successfully used for viscoelastic material characterization experiments in the laboratory, as well as in flight measurements of strain on the surface of scientific balloons during inflation, launch, ascent, and float.

Rand, J. L.↗

NASA NTRS1983

Stiffness reductions during tensile fatigue testing of graphite/epoxy angle-ply laminates

The monitoring of modulus decay during fatigue testing as an indicator of damage accumulation and incipient failure has frequently been postulated. The present study was designed to generate tensile fatigue data under carefully controlled test conditions. A computerized data acquisition system was used to permit the measurement of dynamic modulus without interrupting the fatigue cycling. Two different 8-ply laminate configurations, viz, (+ or - 45)2s and (+ or - 67.5)2s, of a T300/5208 graphite/epoxy composite were tested. The (+ or 45)2s laminate did exhibit some modulus decay, although there was no well-defined correlation with applied stress level or number of cycles. The (+ or - 67.5)2s laminate did not exhibit any measurable modulus decay. Secondary effects observed included a slight recovery of the modulus decay after a test interruption, and a significant viscoelastic (creep) response of the (+ or - 45)2s laminate during fatigue testing.

Odom, E. M.↗

NASA NTRS1985

Transient polar motions and the nature of the asthenosphere for short time scales

A uniformly valid mathematical formalism is developed to study the secular motions of the rotational axis of a layered viscoelastic earth due to seismic excitation. The changes required for implementing the formulation within the framework of the faulting problem. The rationale of adopting the chosen nrheological model, which contains a low-viscosity zone beneath the lithosphere and is based on linear Maxell constitutive relationship, is discussed. The impact of this low-viscosity channel on thhe two families of relaxation time, governing both isostatic readjustment and rotational processes, is considered. It is found that the polar motions depend sensitively on the viscosity structure of the asthenosphere and not at all on the underlying mantle. A gloal low-velocity zone with short-term asthenospheric viscosities less than about 5 x 10 to the 18th Pa-s and widths greater than 50 km is ruled out.

Boschi, E.↗

NASA NTRS1986

Predicting Failures of Composite, Spherical Pressure Vessels

Long-term viscoelastic effects computed to predict bursts. Spherical pressure vessels commonly made of filamentary composites for applications they must light in weight. Program developed for predicting failure of such vessel over long time span. Short-term failure pressures (bursting points) predicted, but long-term structual integrity of laminated vessels studied only now.

Dozier, J. D.↗