SEARCH · Engineering Papers

Results for “slip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Ku band deployed assembly and gimbal

Requirements for shuttle orbiter missions to locate satellites for servicing and to communicate when out of touch with a direct ground link were established. A Ku Band deployed antenna system providing an integrated radar and communications function was designed to meet these requirements. The unique features of the gimbal assembly are described with emphasis on the following: edge mounted antenna to minimize stowage volume in shuttle and maximize gain; unique two axis housing and shaft arrangement to accommodate two runs of waveguide and 55 electrical conductors without requiring slip rings; maximum use of aluminum in gimbal structure to reduce costs; and lubricant chosen to survive Earth and space environments.

Deal, T. E.↗

NASA NTRS1970

Design and Manufacture of Wheels for A Dual-Mode (Manned - Automatic) Lunar Surface Roving Vehicle. Volume 1: Detailed Technical Report

The concept development, testing, evaluation, and the selection of a final wheel design concept for a dual-mode lunar surface vehicle (DLRV) is detailed. Four wheel configurations were fabricated (one open wheel and three closed wheel) (and subjected to a series of soft soil, mechanical, and endurance tests. Results show that the open wheel has lower draw-bar pull (slope climbing) capability in loose soil due to its higher ground pressure and tendency to dig in at high wheel slip. Endurance tests indicate that a double mesh, fully enclosed wheel can be developed to meet DLRV life requirements. There is, however, a 1.0 to 1.8 lb/wheel weight penalty associated with the wheel enclosure. Also the button cleats used as grousers for the closed-type wheels result in local stress concentration and early fatigue failure of the wire mesh. Load deflection tests indicate that the stiffness of the covered wheel increased by up to 50% after soil bin testing, due to increased friction between the fabric and the wire mesh caused by the sand. No change in stiffness was found for the open wheel. The single woven mesh open wheel design with a chevron tread is recommended for continued development

Source record↗

NASA NTRS1970

Design and Manufacture of Wheels for A Dual-Mode (Manned - Automatic) Lunar Surface Roving Vehicle. Volume 2: Proposed Test Plan

A developmental test plan for the wheel and wheel drive assembly of the dual-mode (manned/automated) lunar surface roving vehicle is presented. The tests cover performance, as well as critical environmental characteristics. Insofar as practical, the environmental conditions imposed will be in the sequence expected during the hardware's life from storage through the lunar mission. Test procedures are described for static load deflection and endurance tests. Soft soil tests to determine mobility characteristics including drawbar-pull and thrust vs slip, and motion resistance for various wheel loads are also discussed. Test designs for both ambient and thermal vacuum conditions are described. Facility, transducer, and instrumentation requirements are outlined.

Source record↗

NASA NTRS1980

Equations for determining aircraft motions for accident data

Procedures for determining a comprehensive accident scenario from a limited data set are reported. The analysis techniques accept and process data from either an Air Traffic Control radar tracking system or a foil flight data recorder. Local meteorological information at the time of the accident and aircraft performance data are also utilized. Equations for the desired aircraft motions and forces are given in terms of elements of the measurement set and certain of their time derivatives. The principal assumption made is that aircraft side force and side-slip angle are negligible. An estimation procedure is outlined for use with each data source. For the foil case, a discussion of exploiting measurement redundancy is given. Since either formulation requires estimates of measurement time derivatives, an algorithm for least squares smoothing is provided.

Bach, R. E., Jr.↗

NASA NTRS1980

Effect of cage design on characteristics of high-speed-jet-lubricated 35-millimeter-bore ball bearing

Parametric tests were conducted with a 35 mm bore angular contact ball bearing with a double outer land guided cage. Provisions were made for jet lubrication and outer-ring cooling of the bearing. Test conditions included a combined thrust and radial load at nominal shaft speeds of 48,000 rpm, and an oil-in temperature of 394 K (250 F). Successful operation of the test bearing was accomplished up to 2.5 million DN. Test results were compared with those obtained with similar bearing having a single outer land guided cage. Higher temperatures were generated with the double outer land guided cage bearing, and bearing power loss and cage slip were greater. Cooling the outer ring resulted in a decrease in overall bearing operating temperature.

Schuller, F. T.↗

NASA NTRS1979

A two dimensional model of viscous slot flow

The effects of viscosity on flows through slots are investigated. Using Briley's formulation of the Alternating Direction Implicit method together with the Thompson transformation, numerical solution of viscous incompressible flow through a slot is simulated, for Reynolds number 1000 and openness ratio one tenth. The problem is formulated in terms of stream function and vorticity. A wall iteration of Israeli type is employed to iteratively induce the no slip condition on velocity.

Cooke, C. H.↗

NASA NTRS1980

Release-rate calorimetry of multilayered materials for aircraft seats

Multilayered samples of contemporary and improved fire-resistant aircraft seat materials were evaluated for their rates of heat release and smoke generation. Top layers with glass-fiber block cushion were evaluated to determine which materials, based on their minimum contributions to the total heat release of the multilayered assembly, may be added or deleted. The smoke and heat release rates of multilayered seat materials were then measured at heat fluxes of 1.5 and 3.5 W/cm2. Abrasion tests were conducted on the decorative fabric covering and slip sheet to ascertain service life and compatibility of layers

Fewell, L. L.↗

NASA NTRS1980

On the numerical solution of time-dependent viscous incompressible fluid flows involving solid boundaries

An inherent numerical problem associated with the fully explicit pseudospectral numerical simulation of the incompressible Navier-Stokes equation for viscous flows with no-slip walls is described. A semi-implicit scheme which circumvents this numerical difficulty is presented. In this algorithm the equation of continuity rather than the Poisson equation for pressure is solved directly. Pseudospectral formulation of the channel flow problem using Fourier series and Chebyshev polynomials expansions is given for this scheme. An example demonstrating the applicability of the method is given.

Moin, P.↗

NASA NTRS1980

An axial flow research compressor facility designed for flow measurement in rotor passages

An axial flow research compressor facility, which is designed for relative flow measurement, is described in this paper. The facility has a rotating probe traverse mechanism which is capable of traversing hot wire, pitot and other probes at 0.09 deg intervals across the rotor blade passage. The data transmission system includes rotating transducers, pressure transfer device, ten-channel mercury slip ring unit, scanivalve, etc. The instrumentation includes on-line data processing capability. A brief description of probes used as well as some typical data on the rotor blade static pressure, rotor endwall flow and rotor wake characteristics are given in the paper.

Lakshminarayana, B.↗

NASA NTRS1980

The performance of suppressed carrier receivers in a pulsed RFI environment

This paper investigates the tracking performance of a Costas loop in the presence of single and multiple in-band pulsed RFI signals and receiver additive noise. It is shown that the loop's tracking performance is very sensitive to the pulse durations of the RFI signals, as well as their repetition rates and peak powers relative to those of the desired signal. The presence of in-band RFI can affect the loop's tracking performance in basically three ways. 1) The loop tracks the composite phase of the RFI instead of the phase of the desired signal when the effective RFI power is greater than that of the signal. 2) When the effective RFI power is not sufficiently large to capture the loop, there still will exist static phase error biases which cause the loop to lock at a phase between that of the desired signal and the composite RFI. 3) There is an increase in the rms phase jitter over the nominal design. These latter two effects degrade the bit error probability performance of the receiver. More significantly, if the nominal loop bandwidth is not designed properly to account for the increase in jitter phenomenon, frequency cycle slipping may result.

Simon, M. K.↗

NASA NTRS1980

Computation of three-dimensional viscous flows with the Navier-Stokes equations

The paper presents computations of three-dimensional viscous flows generated with the General Interpolation Method/STAR code based on the time-averaged Navier-Stokes equations. Calculations are presented for three viscous flow problems, and a two dimensional nozzle-exhaust shear flow case is solved and compared to an inviscid slip-line code. This nozzle-exhaust flow case is then extended to three dimensions and the steady solution displayed at pressure contours in the cross planes. The third problem consists of a simulated two-dimensional aircraft inlet flow which includes calculation of the 'spillage' flow and a shock wave/boundary layer interaction in the nozzle.

Spradley, L. W.↗

NASA NTRS1980

Anisotropic Tribological Properties of Silicon Carbide

The anisotropic friction, deformation and fracture behavior of single crystal silicon carbide surfaces were investigated in two categories. The categories were called adhesive and abrasive wear processes, respectively. In the adhesive wear process, the adhesion, friction and wear of silicon carbide were markedly dependent on crystallographic orientation. The force to reestablish the shearing fracture of adhesive bond at the interface between silicon carbide and metal was the lowest in the preferred orientation of silicon carbide slip system. The fracturing of silicon carbide occurred near the adhesive bond to metal and it was due to primary cleavages of both prismatic (10(-1)0) and basal (0001) planes.

Miyoshi, K.↗

NASA NTRS1980

Evaluation of axial lock-up of space shuttle main engine bearings from high pressure oxygen turbopump

The mainshaft support bearings of long life turbopumps for use on the space shuttle were evaluated to determine possible causes of failure. Specific aspects examined include the sensitivity of 15 degree versus 25 degree contact angle bearings with regard to heat damage and thermal runaway, the L/D aspects of the turbine end bearing pair with regard to hang-up due to cocking, the hang-up required to support a 44.5 KN axial load without cartridge slipping, the outer race growth as a result of a 44.5 KN axial load, and bearing torque as a function of axial load. Results indicate that hang-up of the cartridge due to bearing heating is a serious problem especially if poor lubrication of the bearing occurs and that race growth due to axial load can contribute to cartridge lock-up. The experimental evaluation of bearing performance under axial loads indicates that the bearing torque is a strong function of surface lubrication.

Kannel, J. W.↗

NASA NTRS1980

Changes in surface chemistry of silicon carbide (0001) surface with temperature and their effect on friction

Friction studies were conducted with a silicon carbide (0001) surface contacting polycrystalline iron. The surface of silicon carbide was pretreated: (1) by bombarding it with argon ions for 30 minutes at a pressure of 1.3 pascals; (2) by heating it at 800 C for 3 hours in vacuum at a pressure of 10 to the minus eighth power pascal; or (3) by heating it at 1500 C for 3 hours in a vacuum of 10 to the minus eighth power pascal. Auger emission spectroscopy was used to determine the presence of silicon and carbon and the form of the carbon. The surfaces of silicon carbide bombarded with argon ions or preheated to 800 C revealed the main Si peak and a carbide type of C peak in the Auger spectra. The surfaces preheated to 1500 C revealed only a graphite type of C peak in the Auger spectra, and the Si peak had diminished to a barely perceptible amount. The surfaces of silicon carbide preheated to 800 C gave a 1.5 to 3 times higher coefficient of friction than did the surfaces of silicon carbide preheated to 1500 C. The coefficient of friction was lower in the 11(-2)0 direction than in the 10(-1)0 direction; that is, it was lower in the preferred crystallographic slip direction.

Miyoshi, K.↗

NASA NTRS1980

Determination of the hypersonic-continuum/rarefied-flow drag coefficient of the Viking lander capsule 1 aeroshell from flight data

Results of an investigation to determine the full scale drag coefficient in the high speed, low density regime of the Viking lander capsule 1 entry vehicle are presented. The principal flight data used in the study were from onboard pressure, mass spectrometer, and accelerometer instrumentation. The hypersonic continuum flow drag coefficient was unambiguously obtained from pressure and accelerometer data; the free molecule flow drag coefficient was indirectly estimated from accelerometer and mass spectrometer data; the slip flow drag coefficient variation was obtained from an appropriate scaling of existing experimental sphere data. Comparison of the flight derived drag hypersonic continuum flow regime except for Reynolds numbers from 1000 to 100,000, for which an unaccountable difference between flight and ground test data of about 8% existed. The flight derived drag coefficients in the free molecule flow regime were considerably larger than those previously calculated with classical theory. The general character of the previously determined temperature profile was not changed appreciably by the results of this investigation; however, a slightly more symmetrical temperature variation at the highest altitudes was obtained.

Blanchard, R. C.↗

NASA NTRS1981

Transient dynamic analysis of high-speed lightly loaded cylindrical roller bearings. 2: Computer program and results

The governing differential equations of motion for a high speed cylindrical roller bearing are programmed for numerical solution and plotted output. This computer program has the capability of performing a two dimensional or three dimensional simulation. Two numerical solutions of the governing differential equations were obtained to simulate the motion of a roller bearing, one for the two dimensional equations of motion and one for the three dimensional equations of motion. Computer generated plots were obtained and present such data as roller/cage interaction forces, roller/race traction forces, roller/race relative slip velocities and cage angular speed over a nondimensional time equivalent to 1.2 revolutions of the inner race. Roller axial displacement, roller skew angle, and skew moment are also plotted for the three dimensional solution. The trajectory of the cage center is plotted for both the two dimensional and three dimensional solutions.

Conry, T. F.↗

NASA NTRS1980

Commerical (terrestrial) and modified solar array design studies for low cost, low power space applications

The suitability of commercial (terrestrial) solar arrays for use in low Earth orbit is examined. It is shown that commercial solar arrays degrade under thermal cycling because of material flexure, and that certain types of silicones used in the construction of these arrays outgas severely. Based on the results, modifications were made. The modified array retains the essential features of typical commercial arrays and can be easily built by commercial fabrication techniques at low cost. The modified array uses a metal tray for containment, but eliminates the high outgassing potting materials and glass cover sheets. Cells are individually mounted with an adhesive and individually covered with glass cover slips, or clear plastic tape. The modified array is found to withstand severe thermal cycling for long intervals of time.

Kolecki, J. C.↗

NASA NTRS1979

Development of an improved toughness hyperpure silica reflective heat shield

High purity three dimensionally woven silica-silica materials were evaluated for use as a tough reflective heat shield for planetary entry probes. A special weave design was selected to minimize light piping effects through the heat shield thickness. Various weave spacings were evaluated for densification efficiency with an 0.7 micron particle size high purity silica. Spectral hemispherical reflectance was measured from 0.2 to 2.5 microns at room temperature. Reflectance increases due to densification and purity of material were measured. Reflectance of 3D hyperpure silica was higher than 3D astroquartz silica for all wavelengths. Mechanical properties were measured in beam flexure and beam shear tests. Results indicated strengths lower than reported for slip cast fused silica. Low strengths were attributed to low densities achieved through vacuum impregnation.

Rusert, E. L.↗