Results for “process design tool” — Page 46

NASA NTRS2006

A low cost imaging displacement measurement system for spacecraft thermal vacuum testing

A low cost imaging displacement technique suitable for use in thermal vacuum testing was built and tested during thermal vacuum testing of the space infrared telescope facility (SIRTF, later renamed Spitzer infrared telescope facility). The problem was to measure the relative displacement of different portions of the spacecraft due to thermal expansion or contraction. Standard displacement measuring instrumentation could not be used because of the widely varying temperatures on the spacecraft and for fear of invalidating the thermal vacuum testing. The imaging system was conceived, designed, purchased, and installed in approximately 2 months at very low cost. The system performed beyond expectations proving that sub millimeter displacements could be measured from over 2 meters away. Using commercial optics it was possible to make displacement measurements down to 10 (mu)m. An automated image processing tool was used to process the data, which not only speeded up data reduction, but showed that velocities and accelerations could also be measured. Details of the design and capabilities of the system are discussed along with the results of the test on the observatory. Several images from the actual test are presented.

thermal vacuum↗

NASA NTRSDate not supplied

Integration of Design Data Into Automated Fiber Placement Process Planning Metrics

With the ever-expanding aviation industry, a need is arising for more rapid production of composite aircraft to meet increasing demand. State-of-the-art aircraft such as the Boeing 787showcase 50% composite material usage by weight, highlighting this emerging industry-wide adoption of the material system. Currently, many of the large structures associated with these aircraft are manufactured additively via Automated Fiber Placement (AFP). The AFP process shows great potential for efficient manufacturing, however unavoidable defects still occur because of tool surface geometry, placement errors, or poor process planning, resulting in decreased quality and throughput. Due to such effects, it is critical to incorporate design for manufacturing (DFM) principles to achieve the optimal manufacturing plan and resulting structure. This work will develop a methodology for incorporating design information into process planning metrics in an automated fashion to achieve an optimal set of process inputs.The analysis incorporates HyperX, Computer Aided Process Planning (CAPP) and Vericut Composite Programming (VCP). Safety margins from HyperX are imported into CAPP where AFP defects are mapped to the values. The resulting margins are then incorporated into the CAPP manufacturability algorithms, creating a design informed process planning analysis

Automated Fiber Placement↗

NASA NTRS1990

Automating analog design: Taming the shrew

The pace of progress in the design of integrated circuits continues to amaze observers inside and outside of the industry. Three decades ago, a 50 transistor chip was a technological wonder. Fifteen year later, a 5000 transistor device would 'wow' the crowds. Today, 50,000 transistor chips will earn a 'not too bad' assessment, but it takes 500,000 to really leave an impression. In 1975 a typical ASIC device had 1000 transistors, took one year to first samples (and two years to production) and sold for about 5 cents per transistor. Today's 50,000 transistor gate array takes about 4 months from spec to silicon, works the first time, and sells for about 0.02 cents per transistor. Fifteen years ago, the single most laborious and error prone step in IC design was the physical layout. Today, most IC's never see the hand of a layout designer: and automatic place and route tool converts the engineer's computer captured schematic to a complete physical design using a gate array or a library of standard cells also created by software rather than by designers. CAD has also been a generous benefactor to the digital design process. The architect of today's digital systems creates the design using an RTL or other high level simulator. Then the designer pushes a button to invoke the logic synthesizer-optimizer tool. A fault analyzer checks the result for testability and suggests where scan based cells will improve test coverage. One obstinate holdout amidst this parade of progress is the automation of analog design and its reduction to semi-custom techniques. This paper investigates the application of CAD techniques to analog design.

Barlow, A.↗

NASA NTRS1972

Program management aid for redundancy selection and operational guidelines

Although this criterion was developed specifically for use on the shuttle program, it has application to many other multi-missions programs (i.e. aircraft or mechanisms). The methodology employed is directly applicable even if the tools (nomographs and equations) are for mission peculiar cases. The redundancy selection criterion was developed to insure that both the design and operational cost impacts (life cycle costs) were considered in the selection of the quantity of operational redundancy. These tools were developed as aids in expediting the decision process and not intended as the automatic decision maker. This approach to redundancy selection is unique in that it enables a pseudo systems analysis to be performed on an equipment basis without waiting for all designs to be hardened.

Hodge, P. W.↗

DOE OSTI2020

Conceptual Fuel Element Design Candidates for Conversion of High Flux Isotope Reactor with Low-Enriched Uranium Silicide Dispersion Fuel

Engineering design studies are underway to assess the feasibility of converting the High Flux Isotope Reactor (HFIR) to operate with low-enriched uranium (LEU) silicide dispersion (U3Si2-Al) fuel. These studies are supported by the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization. A systematic approach employing neutronic and thermal-hydraulic analyses have been performed with the ORNL Shift and HFIR Steady State Heat Transfer Code tools, respectively, to predict reactor performance and thermal safety margins for proposed LEU3Si2-Al fuel designs. The design process was initiated by generating an optimized design with fabrication features identified from previous studies that result in excellent performance and safety metrics. The approach continued by substituting a single fabrication feature anticipated to be difficult to manufacture with another feature expected to perform an analogous function to that of the removed feature. Four conceptual fuel element design candidates, with various fabrication features, for conversion of HFIR with 4.8 gU/cm3 LEU3Si2-Al fuel have been generated and shown to meet pre-defined performance and safety metrics. Results to date indicate that HFIR could convert with the subject fuel system and meet performance and safety requirements if, among other considerations, fabrication of the specific design features are demonstrated and qualification of the fuel is complete under HFIR-specific conditions.

Chandler, David↗

DOE OSTI2023

An Implicit Approach to Phase Field Modeling of Solidification for Additively Manufactured Alloys [Slides]

We are leveraging modern algorithms and computational science to provide a route to predictive simulation of microstructure evolution on emerging exascale architectures. We are utilizing the fastest supercomputers in the world for modeling and simulation of microstructure evolution for generation of data under AM conditions. Solidification conditions in AM can be tailored for the reliable design of materials to specific performance requirements. Developing computational tools to further characterize alloys and correlate the processing-structure-properties-performance (PSPP) relationship.

36 MATERIALS SCIENCE↗

DOE OSTI2025

NARUC Resilience Framework

The NARUC Resilience Framework provides state regulators and other key stakeholders with a structured approach to considering policies and programs that will enhance grid resilience amid evolving technological, environmental and economic challenges. This Framework consolidates insights from nationwide workshops and peer discussions into six actionable components: (1) setting goals and objectives, (2) leveraging use cases, (3) establishing shared definitions, (4) ensuring inclusive process leadership, (5) addressing critical design questions, and (6) guiding implementation. This Framework is intended as a strategic tool for regulators to navigate resilience investments, prioritize affordability, integrate stakeholder needs, and foster collaboration across agencies, all while balancing cost-effectiveness with societal and economic resilience outcomes. By presenting a structured approach to decision-making rather than prescriptive solutions, the Framework supports nuanced, jurisdiction-specific resilience planning and is adaptable to the dynamic demands of modern energy systems

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2025

Modular Autonomous Experimentation for Biological Applications

The Modular Autonomous Research System (MARS) was created to address a key challenge in scientific discovery: experiments are often slow, require significant manual labor, and generate data that is not easily integrated across different tools. This limits how quickly scientists can explore new materials, processes, and chemical reactions. Our motivation was to design a system that makes research faster, more reliable, and adaptable by combining automation with artificial intelligence. By doing so, we aimed to reduce human error, accelerate discovery, and allow researchers to quickly test many possibilities that would otherwise take months or years. Our approach was to build a flexible platform that connects laboratory robots, measurement instruments, and a central data system, all guided by artificial intelligence. MARS integrates liquid handling robots, robotic arms, and plate readers with an intelligent decision-making system that chooses the most informative experiments to run next. This creates a closed loop where experiments are performed automatically, the data is analyzed in real time, and new conditions are immediately tested. Through this work, we demonstrated that MARS can carry out multiple experiments with little or no human intervention, adapt to different scientific problems, and handle uncertain or noisy measurements in a robust way. The results show that modular and intelligent automation can significantly accelerate the pace of discovery, providing a model for future self-driving laboratories. This approach addresses the growing scientific need for adaptable, data-driven research platforms that can keep up with the complexity and scale of modern science.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1982

Low-cost composite blades for the Mod-0A wind turbines

Low cost approaches to the design and fabrication of blades for a two-bladed 200 kW wind turbine were identified and the applicability of the techniques to larger and smaller blades was assessed. Blade tooling was designed and fabricated. Two complete blades and a partial blade for tool tryout were built. The patented TFT process was used to wind the entire blade. This process allows rapid winding of an axially oriented composite onto a tapered mandrel, with tapered wall thickness. The blade consists of a TFT glass-epoxy airfoil structure filament wound onto a steel root end fitting. The fitting is, in turn, bolted to a conical steel adapter section to provide for mounting attachment to the hub. Structural analysis, blade properties, and cost and weight analysis are described.

Weingart, O.↗

NASA NTRS1979

Advanced manufacturing development of a composite empennage component for L-1011 aircraft

Work in process verification and tooling development continued. The decision was made to redesign the ribs to a more producible design. The bead was eliminated and the truss ribs changed to plain C sections. The solid web rib stiffeners were eliminated as well as the beads and the webs are now reinforced with a syntactic core. Syntectic is an epoxy containing glass microballoons. Two cover specimens were successfully tested. The first specimen (H27) was designed to verify the stability and compression strength of the cover when it is hot and wet. Failure occurred at 120 percent of design ultimate load. As the failure appeared to be fixture induced and was limited to one end of the panel, the remainder of the panel will be tested. The second specimen (H28) was designed to verify the failsafe aspects of the design. The test verified the design. Preparation of the PRVT test facility is nearing completion and all ten spar durability specimens were installed in the test chambers.

Source record↗

NASA NTRS1994

Taking advantage of ground data systems attributes to achieve quality results in testing software

During the software development life cycle process, basic testing starts with the development team. At the end of the development process, an acceptance test is performed for the user to ensure that the deliverable is acceptable. Ideally, the delivery is an operational product with zero defects. However, the goal of zero defects is normally not achieved but is successful to various degrees. With the emphasis on building low cost ground support systems while maintaining a quality product, a key element in the test process is simulator capability. This paper reviews the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) test tool that is used in the acceptance test process for unmanned satellite operations control centers. The TASS is designed to support the development, test and operational environments of the Goddard Space Flight Center (GSFC) operations control centers. The TASS uses the same basic architecture as the operations control center. This architecture is characterized by its use of distributed processing, industry standards, commercial off-the-shelf (COTS) hardware and software components, and reusable software. The TASS uses much of the same TPOCC architecture and reusable software that the operations control center developer uses. The TASS also makes use of reusable simulator software in the mission specific versions of the TASS. Very little new software needs to be developed, mainly mission specific telemetry communication and command processing software. By taking advantage of the ground data system attributes, successful software reuse for operational systems provides the opportunity to extend the reuse concept into the test area. Consistency in test approach is a major step in achieving quality results.

Sigman, Clayton B.↗

NASA NTRS2002

The Role of Formal Experiment Design in Hypersonic Flight System Technology Development

Hypersonic airbreathing engine (scramjet) powered vehicles are being considered to replace conventional rocket-powered launch systems. Effective utilization of scramjet engines requires careful integration with the air vehicle. This integration synergistically combines aerodynamic forces with propulsive cycle functions of the engine. Due to the highly integrated nature of the hypersonic vehicle design problem, the large flight envelope, and the large number of design variables, the use of a statistical design approach in design is effective. Modern Design-of-Experiments (MDOE) has been used throughout the Hyper-X program, for both systems analysis and experimental testing. Application of MDOE fall into four categories: (1) experimental testing; (2) studies of unit phenomena; (3) refining engine design; and (4) full vehicle system optimization. The MDOE process also provides analytical models, which are also used to document lessons learned, supplement low-level design tools, and accelerate future studies. This paper will discuss the design considerations for scramjet-powered vehicles, specifics of MDOE utilized for Hyper-X, and present highlights from the use of these MDOE methods within the Hyper-X Program.

McClinton, Charles R.↗

NASA NTRS1982

Bank Record Processing

Barnett Banks of Florida, Inc. operates 150 banking offices in 80 Florida cities. Banking offices have computerized systems for processing deposits or withdrawals in checking/savings accounts, and for handling commercial and installment loan transactions. In developing a network engineering design for the terminals used in record processing, an affiliate, Barnett Computing Company, used COSMIC's STATCOM program. This program provided a reliable network design tool and avoided the cost of developing new software.

Source record↗

NASA NTRS2003

Risk based decision tool for space exploration missions

This paper presents an approach and corresponding tool to assess and analyze the risks involved in a mission during the pre-phase A design process. This approach is based on creating a risk template for each subsystem expert involved in the mission design process and defining appropriate interactions between the templates.

space exploration proposals↗

NASA NTRS2008

System Definition of the James Webb Space Telescope (JWST) Integrated Science Instrument Module (ISIM)

The Integrated Science Instrument Module (ISIM) for the James Webb Space Telescope (JWST) provides the critical functions and the environment for the four science instruments on JWST. This complex system development across many international organizations presents unique challenges and unique solutions. Here we describe how the requirement flow has been coordinated through the documentation system, how the tools and processes are used to minimize impact to the development of the affected interfaces, how the system design has matured, how the design review process operates, and how the system implementation is managed through reporting to ensure a truly world class scientific instrument compliment is created as the final product.

Lundquist, Ray↗

NASA NTRS2016

Rapid Preliminary Design of Interplanetary Trajectories Using the Evolutionary Mission Trajectory Generator

This set of tutorial slides is an introduction to the Evolutionary Mission Trajectory Generator (EMTG), NASA Goddard Space Flight Center's autonomous tool for preliminary design of interplanetary missions. This slide set covers the basics of creating and post-processing simple interplanetary missions in EMTG using both high-thrust chemical and low-thrust electric propulsion along with a variety of operational constraints.

optimization↗

NASA NTRS2022

Application Table: A Bridge Connecting the Designing “With-The-Material” and “The-Material” Paradigms

Over the last few decades, advances in high-performance computing, new material characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. In 2016 NASA sponsored a 2040 Vision study (which appeared in 2018) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. The study envisions a cyber-physical-social ecosystem comprised of experimentally verified and validated (V & V) computational models, tools, and techniques, along with the associated digital tapestry, that impacts the entire supply chain to enable cost-effective, rapid, and revolutionary design of “fit-for-purpose” materials, components, and systems. Consequently, the development of a robust information management system that incorporates (across the full life cycle) both experimental (real data) and virtual data resulting from the application of various simulation tools (at single or multiple length scales), therefore enabling the virtual design and optimization of materials throughout their processing – internal structure – property – performance envelope, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality, and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. This is particularly true when attempting to merge ICME practices with recent additive manufacturing technology which will enable production of the resulting 2040 Vision material and structural designs. At NASA Glenn Research Center we are exploring the future of material science through the use of novel characterization methodologies, high performance computing, and recently an emphasis on integrated computational materials engineering (ICME). Herein, recent efforts to incorporate an Application Table within NASA Glenn Research Center’s ICME Granta MI database is presented. The goal is to provide a place where material and structural application information/requirements can be linked so as to marry the “design the-material” and the “design-with-material” paradigms and thereby enable application-driven design and optimization of materials and structures by providing a central location that links material processing at various length scales to the application’s performance requirements. This paper discusses the specifics of this Application Table as well as best practices and key principles for the development of a robust materials information management system to enable the 2040 Vision integrated materials and structures ecosystem. Furthermore, it presents the intended role of the Application Table in the future of ICME design of “fit-for-purpose” materials, showing the need for a well-established framework that can successfully bridge the gap between the design “the material” and design “with-the-material” paradigms.

Materials↗

NASA NTRSDate not supplied

Application Table: A Bridge Connecting the Designing “With-the-Material” and “the-Material”

Over the last few decades, advances in high-performance computing, new material characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. In 2016 NASA sponsored a 2040 Vision study (which appeared in 2018) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. The study envisions a cyber-physical-social ecosystem comprised of experimentally verified and validated (V & V) computational models, tools, and techniques, along with the associated digital tapestry, that impacts the entire supply chain to enable cost-effective, rapid, and revolutionary design of “fit-for-purpose” materials, components, and systems. Consequently, the development of a robust information management system that incorporates (across the full life cycle) both experimental (real data) and virtual data resulting from the application of various simulation tools (at single or multiple length scales), therefore enabling the virtual design and optimization of materials throughout their processing – internal structure – property – performance envelope, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality, and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. This is particularly true when attempting to merge ICME practices with recent additive manufacturing technology which will enable production of the resulting 2040 Vision material and structural designs. At NASA Glenn Research Center we are exploring the future of material science through the use of novel characterization methodologies, high performance computing, and recently an emphasis on integrated computational materials engineering (ICME). Herein, recent efforts to incorporate an Application Table within NASA Glenn Research Center’s ICME Granta MI database is presented. The goal is to provide a place where material and structural application information/requirements can be linked so as to marry the “design the-material” and the “design-with-material” paradigms and thereby enable application-driven design and optimization of materials and structures by providing a central location that links material processing at various length scales to the application’s performance requirements. This paper discusses the specifics of this Application Table as well as best practices and key principles for the development of a robust materials information management system to enable the 2040 Vision integrated materials and structures ecosystem. Furthermore, it presents the intended role of the Application Table in the future of ICME design of “fit-for-purpose” materials, showing the need for a well-established framework that can successfully bridge the gap between the design “the material” and design “with-the-material” paradigms.

Materials↗