Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phenol”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Domestic wash water reclamation for reuse as commode water supply using filtration: Reverse-osmosis separation technique

A combined filtration-reverse-osmosis water recovery system has been evaluated to determine its capability to reclaim domestic wash water for reuse as a commode water supply. The system produced water that met all chemical and physical requirements established by the U.S. Public Health Service for drinking water with the exception of carbon chloroform extractables, methylene blue active substances, and phenols. It is thought that this water is of sufficient quality to be reused as commode supply water. The feasibility of using a combined filtration and reverse-osmosis technique for reclaiming domestic wash water has been established. The use of such a technique for wash-water recovery will require a maintenance filter to remove solid materials including those less than 1 micron in size from the wash water. The reverse-osmosis module, if sufficiently protected from plugging, is an attractive low-energy technique for removing contaminants from domestic wash water.

Hall, J. B., Jr.↗
NASA NTRS1974

Interaction of gases with ablative composites. I - Ar, CO2, and N2

The sorption of argon, carbon dioxide, and nitrogen on two heat shield composites (SLA-561 and SLA-561V) and on the SLA components was measured over the pressure range of 0.001 to 760 torr and in the temperature range of 30 to 50 C. The sorption of the gases by both the composites and the components varied directly with pressure. The sorption of CO2 by the phenolic spheres and the silicone elastomer and of Ar by the silicone elastomer varied inversely with temperature. The mechanism involved in the gas sorption was primarily absorption.

King, C. A.↗
NASA NTRS1974

Outer planet probe entry thermal protection. II - Heat shielding requirements

Solutions are presented for the material thermal response for heat shields of blunt probes entering Saturn and Uranus. Both monolithic and sandwich concepts were considered having exposed charring ablative or reflective materials. The solutions show that (1) Teflon heat shields are sized by mass loss considerations, other materials (unless entering the Uranus cold-dense atmosphere) by heat soak considerations, (2) steeper entries require less heat shield mass, (3) sizing requirements vary little about the bodies for heat soak dominated materials, and (4) carbon-phenolic appears superior overall, but silica is superior for the steeper entries and the high helium content atmospheres.

Nicolet, W. E.↗
NASA NTRS1974

Interaction of gases with ablative composites. II - Water

An investigation was conducted to study the sorption of water on two ablative composites and their components as a function of pressure and temperature. A pressure range from 0.001 to 10 torr and a temperature range from 25 to 35 C were considered in the investigation. It was found that the sorption of water vapor by the ablative composites and their components varied directly with pressure. The components of the ablative composites included phenolic spheres, cork, a carbon-glass fiber mixture, glass spheres, silica fibers, and a silicone elastomer.

Honeycutt, R. H., III↗
NASA NTRS1975

Prototype rigid polyimide components

The activity is reported which was conducted for utilizing spin-off Apollo base technology to fabricate a variety of commercial and aerospace related parts that are nonflammable and resistant to high-temperature degradation. Manufacturing techniques and the tooling used to fabricate each of the polyimide/glass structures is discussed. A brief history, tracing the development of high-temperature polyimide resins, is presented along with a discussion of the properties of DuPont's PI 2501/glass material (later redesignated PI 4701/glass). Mechanical and flammability properties of DuPont's PI 2501/glass laminates are compared with epoxy, phenolic, and silicone high-temperature resin/glass material systems. Offgassing characteristics are also presented. A discussion is included of the current developments in polyimide materials technology and the potential civilian and government applications of polyimide materials to reduce fire hazards and increase the survivability of men and equipment.

Wykes, D. H.↗
NASA NTRS1974

Major uncertainties influencing entry probe heat shield design

Factors influencing the design of an outer planet probe heat shield are discussed. Major factors included are: uncertainties in composition and scale height of the planet atmospheres; the augmentation/attenuation of entry heating by ablation products requires more computer study and testing; carbon heat shields, especially carbon phenolic, possessing improved resistance to spallation need developing; and white silica reflecting heat shields with improved resistance to bulk vitrification need further developing.

Congdon, W.↗
NASA NTRS1975

Interaction of graphite and ablative materials with CO2-laser, carbon-arc, and xenon-arc radiation

The behavior of graphite and several charring ablators in a variety of high radiative heat flux environments was studied in various radiative environments produced by a CO2 laser and a carbon arc facility. Graphite was also tested in xenon arc radiation. Tests were conducted in air nitrogen, helium, and a mixture of CO2 and nitrogen, simulating the Venus atmosphere. The experimental results are compared with theoretical results obtained with a one dimensional charring ablator analysis and a two dimensional subliming ablator analysis. Photomicroscopy showed no significant differences in appearance or microstructure of the charring ablators or graphite after testing in the three different facilities, indicating that the materials respond fundamentally the same to the radiation of different frequencies. The performance of phenolic nylon and graphite was satisfactorily predicted with existing analyses and published material property data.

Brewer, W. D.↗
NASA NTRS1975

Phase 2 study of improved materials for use on Scout rocket motor nozzles

Nozzle material performance data were obtained, and the feasibility was determined of using new materials on the Scout rocket motor nozzles. Stress and heat transfer analyses were conducted to aid in the selection of optimum materials for nozzle tests. A reimpregnated and graphitized throat insert was fabricated along with two nozzles with ablative throats. The dissection and determining of char and erosion of two nozzles fired on X-259 loaded cases are discussed; one of the nozzles used a graphite phenolic ablative throat insert, and the other unit was a standard X-259 nozzle with a reduced area ATJ graphite throat insert.

Stutzman, R. D.↗
NASA NTRS1974

Evaluation of the energy transfer in the char zone during ablation. Part 2: In-depth response of ablative composites, volume 1

The decomposition of ablative composites is described along with the transport phenomena of pyrolysis gases which result from the decomposition of these plastics as they flow through the porous char of char-forming ablators. The pyrolysis products are those formed by the thermal degradation of nylon-phenolic resin and silicone elastomer composites. Emphasis is placed on the nature and extent of chemical reactions of the pyrolysis products and the char, along with the energy absorbed by the combined pyrolysis and char zone. Chemical reactions with thermodynamically consistent kinetic data are determined in order to develop a realistic analysis for predicting the thermal performance of ablative heat shields.

Pike, R. W.↗
NASA NTRS1975

Probing a planetary atmosphere - Pioneer Venus spacecraft description

This paper describes the four Pioneer Venus probe spacecraft which will explore the atmosphere of Venus in mid-December, 1978. The probes, one large and three small, will carry a complement of sixteen scientific instruments which will make measurements from entry (200 km-altitude) down to the planet surface. The surface environment, approximately 770 K temperature and 95 bar. pressure, leads to a design in which the equipment complement is housed in internally insulated, spherical pressure vessels. Entry deceleration and stabilization are provided by 45 deg. half-angle conical forebodies, heat protected by carbon phenolic ablative heat shields. For the large probe, a parachute provides additional retardation between 67 and 44 km altitude, a region of extreme scientific interest.

Nolte, L. J.↗
NASA NTRS1976

Development of a protective decorative fire resistant low smoke emitting, thermally stable coating material

The development of suitable electrocoatings and subsequent application to nonconductive substrates are discussed. Substrates investigated were plastics or resin-treated materials such as FX-resin (phenolic-type resin) impregnated fiberglass mat, polyphenylene sulfide, polyether sulfone and polyimide-impregnated unidirectional fiberglass. Efforts were aimed at formulating a fire-resistant, low smoke emitting, thermally stable, easily cleaned coating material. The coating is to be used for covering substrate panels, such as aluminum, silicate foam, polymeric structural entities, etc., all of which are applied in the aircraft cabin interior and thus subject to the spillages, scuffing, spotting and the general contaminants which prevail in aircraft passenger compartments.

Source record↗
NASA NTRS1975

Development of lightweight reinforced plastic laminates for spacecraft interior applications

Lightweight, Kevlar - reinforced laminating systems that are non-burning, generate little smoke in the space shuttle environment, and are physically equivalent to the fiberglass/polyimide system used in the Apollo program for non-structural cabin panels, racks, etc. Resin systems representing five generic classes were screened as matrices for Kevlar 49 reinforced laminates. Of the systems evaluated, the polyimides were the most promising with the phenolics a close second. Skybond 703 was selected as the most promising resin candidate. With the exception of compression strength, all program goals of physical and mechanical properties were exceeded. Several prototype space shuttle mobility and translation handrail segments were manufactured using Kevlar/epoxy and Kevlar-graphite/epoxy. This application shows significant weight savings over the baseline aluminum configuration used previous. The hybrid Kevlar-graphite/epoxy is more suitable from a processing standpoint.

Hertz, J.↗
NASA NTRS1976

Experimental evaluation of outer planets probe thermal insulation concepts

An experimental program was conducted to evaluate various thermal insulation concepts for use in the Outer Planets Probe (OPP) during entry and descent into the atmospheres of Jupiter, Saturn, and Uranus. Phenolic fiberglass honeycomb specimens representative of the OPP structure were packed and tested with various fillers: Thermal conductivity measurements were made over a temperature range of 300 K to 483 K and pressures from vacuum up to 10 atmospheres in helium and nitrogen gas environments. The conductivity results could not be fully explained so new test specimens were designed with improved venting characteristics, and tested to determine the validity of the original data. All of the conductivity data showed results that were substantially higher than expected. The original test data in helium were lower than the data from the redesigned specimens, probably due to inadequate venting of nitrogen gas from the original specimens. The thermal conductivity test results show only a marginal improvement in probe thermal protection performance for a filled honeycomb core compared to an unfilled core. In addition, flatwise tension tests showed a severe bond strength degradation due to the inclusion of either the powder or foam fillers. In view of these results, it is recommended that the baseline OPP design utilize an unfilled core.

Grote, M. G.↗
NASA NTRS1976

A composite system approach to aircraft cabin fire safety

The thermochemical and flammability characteristics of two polymeric composites currently in use and seven others being considered for use as aircraft interior panels are described. The properties studied included: (1) limiting oxygen index of the composite constituents; (2) fire containment capability of the composite; (3) smoke evolution from the composite; (4) thermogravimetric analysis; (5) composition of the volatile products of thermal degradation; and (6) relative toxicity of the volatile products of pyrolysis. The performance of high temperature laminating resins such as bismaleimides is compared with the performance of phenolics and epoxies. The relationship of increased fire safety with the use of polymers with high anaerobic char yield is shown. Processing parameters of one of the baremaleimide composites are detailed.

Kourtides, D. A.↗
NASA NTRS1976

Graphite and ablative material response to CO2 laser, carbon-arc, and xenon-arc radiation

The behavior was investigated of graphite and several charring ablators in a variety of high-radiative heat-flux environments. A commercial-grade graphite and nine state-of-the-art charring ablators were subjected to various radiative environments produced by a CO2 laser and a carbon arc. Graphite was also tested in xenon-arc radiation. Heat-flux levels ranged from 10 to 47 MW/sq m. Tests were conducted in air, nitrogen, helium, and a CO2-N2 mixture which simulated the Venus atmosphere. The experimental results were compared with theoretical results obtained with a one-dimensional charring-ablator analysis and a two-dimensional subliming-ablator analysis. Neither the graphite nor the charring ablators showed significant differences in appearance or microstructure after testing in the different radiative environments. The performance of phenolic nylon and graphite was predicted satisfactorily with existing analyses and published material property data. Good agreement between experimental and analytical results was obtained by using sublimation parameters from a chemical nonequilibrium analysis of graphite sublimation. Some charring ablators performed reasonably well and could withstand radiative fluxes of the level encountered in certain planetary entries. Other materials showed excessive surface recession and/or large amounts of cracking and spalling, and appear to be unsuitable for severe radiative environments.

Brewer, W. D.↗
NASA NTRS1976

Entry into outer planet environments. II - Performance of volume reflecting hyperpure silica heat shields

The performance of hyperpure silica heat shields that backscatter incident radiation in the depths of the material, i.e., a volume reflecting heat shield, is mapped for probes entering the atmospheres of Saturn and Uranus. Three models of each atmosphere are considered; the warm, nominal, and cool models. The most recent thermophysical and optical properties of hyperpure silica are employed. Detailed incident radiative spectra and the effects of ablation on radiative and convective heating obtained from benchmark flowfield solutions are used. In-depth material response is examined and results are presented in terms of the peak rear-face temperature as a function of initial thickness for each atmosphere. Results are compared with carbon phenolic heat-shield requirements.

Howe, J. T.↗
NASA NTRS1976

Flammability characteristics of aircraft interior composites

The thermochemical and flammability characteristics of two polymeric composites currently in use and seven others being considered for use as aircraft interior panels are described. The properties studied included: (1) oxygen index of the composite constituents; (2) fire containment capability of the composite; (3) smoke evolution from the composite; (4) thermogravimetric analysis; (5) composition of the volatile products of pyrolysis. The performance of foam filled honeycomb laminated panels consisting of high-temperature laminating bismaleimide resins is compared with the performance of empty honeycomb laminated panels consisting of laminating epoxy or phenolic resins at similar densities. Processing parameters of one of the bismaleimide composites is detailed.

Kourtides, D. A.↗